Add a quirk for a host controller that always sets
a Transfer Complete interrupt status for the stop
command even when a busy response is not indicated.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 98e90de99a
"mmc: host: switch OF parser to use gpio descriptors"
switched the semantic behaviour of card detect and read
only flags such that the inversion capability flag would
only be set if inversion was explicitly specified in the
device tree, in the hopes that no-one was using double
inversion.
It turns out that the XOR:ing between the explicit
inversion was indeed in use, so we need to restore the
old semantics where both ways of inversion are checked
and the end result XOR:ed.
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add MMC_POWER_UNDEFINED for power_mode in struct mmc_ios and use it as
the initial value of host->ios.power_mode.
For hosts with MMC_CAP2_NO_PRESCAN_POWERUP, this makes the later
mmc_power_off() do real power-off things instead of NOP, and further
prevents state messed up in cards that was already initialized (eg. by
BIOS of UEFI driver).
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Replace ext_csd "enhanced_area_en" attribute by
"partition_setting_completed". It was used whether or
not enhanced user area is defined and without checks of
EXT_CSD_PARTITION_SETTING_COMPLETED bit.
Signed-off-by: Grégory Soutadé <gsoutade@neotion.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This makes it possible to get the write protect (read only)
GPIO line from a GPIO descriptor. Written to exactly mirror
the card detect function.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Historically, we have been using MMC_CAP* to handle host HW issues and
currently the block layer uses MMC_CAP2_NO_MULTI_READ flag for a multi
I/O HW bug workaround.
There are a few tweaks needed to make MMC_CAP2_NO_MULTI_READ suite all
situations. Therefore let's add an optional host ops callback to enable
host drivers to return the number of blocks it allows per request.
In a future patch and when host drivers have converted to the new
callback, MMC_CAP2_NO_MULTI_READ shall be removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is fully legal for a controller to start handling busy-end interrupt
before it has signaled that the command has completed. So make sure
we do things in the proper order, Or it results that command interrupt
is ignored so it can cause unexpected operations. This is founded at some
toshiba emmc with the bellow warning.
"mmc0: Got command interrupt 0x00000001 even though
no command operation was in progress."
This issue has been also reported by Youssef TRIKI:
It is not specific to Toshiba devices, and happens with eMMC devices
as well as SD card which support Auto-CMD12 rather than CMD23.
Also, similar patch is submitted by:
Gwendal Grignou <gwendal@chromium.org>
Changes since v1:
Fixed conflict with the next of git.linaro.org/people/ulf.hansson/mmc.git
and Tested if issue is fixed again.
Signed-off-by: Hankyung Yu <hankyung.yu@lge.com>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Tested-by: Youssef TRIKI <youssef.triki@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
eMMC card can support up to 7 physical partitions, including 2 boot,
1 RPMB and 4 GPs. Change MMC_NUM_PHY_PARTITION from 6 to 7, which is
the correct value.
Signed-off-by: Yi Sun <yi.y.sun@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Switch the common SDHCI code over to use mmc_host's regulator pointers
and remove the ones in the sdhci_host structure. Additionally, use the
common mmc_regulator_get_supply function to get the regulators and set
the ocr_avail mask.
This change sets the ocr_avail directly based upon the voltage ranges
supported which ensures ocr_avail is set correctly while allowing the
use of regulators that can't provide exactly 1.8v, 3.0v, or 3.3v.
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Track whether preset mode is currently enabled in hardware, and use that
when making decisions elsewhere in the code rather than reading the
register and checking the bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than reading back the timing information from the registers,
cache it locally. This allows implementations to translate the UHS
timing by overriding the set_uhs_signaling() method as required
without also having to emulate the SDHCI_HOST_CONTROL2 register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
The Freescale esdhc driver is the only driver which needs the interrupt
registers restored after a reset. Move this quirk to be part of the
ESDHC driver implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
There's no requirement to have the card tasklet separate now that we
have a threaded interrupt handler, so kill this and move the called
code into the threaded part of the handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Use a generic threaded interrupt handler for SDIO interrupt handling,
rather than allowing the SDIO core code to buggily spawn its own
thread. This results in host drivers to be more in control of how
SDIO interrupts are acknowledged in the hardware, rather than having
the internals of the SDIO core placed upon them, possibly resulting
in sub-standard handling.
At least one SDHCI implementation specifies a very specific sequence
to deal with a card interrupt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rather than the SDIO support spawning it's own thread for handling card
interrupts, use the generic IRQ infrastructure for this, triggering it
from the host interface's interrupt handling directly.
This avoids a race between the parent thread waiting to receive an
interrupt response from the card, and the slow startup from the sdio
irq thread, which can occur as a result of high system load (eg, while
udev is running.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
[Ulf Hansson] Resolved conflict
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Callers of mmc_regulator_get_supply could benefit from knowing if either
of the regulators are present but not yet available. Since callers do
not currently examine the return value, modify this function to return
zero or -EPROBE_DEFER if either regulator get returns the same.
Furthermore, since callers check vmmc/vqmmc using IS_ERR and can deal
with absent regulators, switch to devm_regulator_get_optional. This has
the added benefit of allowing this function to behave correctly even in
the !CONFIG_REGULATOR case such that the stub can be removed.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high
speed DDR interface timing from HS200. Clock frequency is up to 200MHz
and only 8-bit bus width is supported. In addition, tuning process of
HS200 is required to synchronize the command response on the CMD line
because CMD input timing for HS400 mode is the same as HS200 mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Jackey Shen <jackey.shen@amd.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Current implementation for bus speed mode selection is too
complicated. This patch is to simplify the codes and remove
some duplicate parts.
The following changes are including:
* Adds functions for each mode selection(HS, HS-DDR, HS200 and etc)
* Rearranged the mode selection sequence with supported device type
* Adds maximum speed for HS200 mode(hs200_max_dtr)
* Adds field definition for HS_TIMING of EXT_CSD
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Device types which are supported by both host and device can be
identified when EXT_CSD is read. There is no need to check host's
capability anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Timing mode identifier has same role and can take the place
of speed mode. This change removes all related speed mode.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Fix the following sparse warnings:
drivers/mmc/card/block.c:2421:9: warning: Using plain integer as NULL pointer
drivers/mmc/core/quirks.c:69:9: warning: Using plain integer as NULL pointer
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
This change removes the callback from atomic context which it doesn't
need to be in, and puts it in line with the debounced rescan.
This code is based on these e-mail threads with Christian Daudt:
https://lkml.org/lkml/2013/8/19/539https://lkml.org/lkml/2014/3/19/79
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add functions to request a CD GPIO using the GPIO descriptor API.
Note that the new request function is paired with mmc_gpiod_free_cd()
not mmc_gpio_free_cd(). Note also that it must be called prior to
mmc_add_host() otherwise the caller must also call
mmc_gpiod_request_cd_irq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
None of this code is currently used: there are no definitions of
struct sdhci_plat_data in arch/arm, neither are there any DT properties
which use card_power_gpio/power_active_high/power_always_enb. In any
case, slot power control should be rigged up via vmmc and the regulator
subsystem in the DT case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <chris@printf.net>
Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Rename host->max_discard_to to host->max_busy_timeout, to reflect that
it tells the mmc core layer about the maximum supported busy detection
timeout by the host.
This timeout is at the moment only applicable to erase/trim/discard
commands. By the renaming we provide the option of make use of it for
other commands that cares about busy detection. In other words, those
commands that wants an R1B response, like for example the mmc switch
command.
Do note that the max_busy_timeout is supposed to be specified only by
hosts supporting MMC_CAP_WAIT_WHILE_BUSY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Add support for realtek rts5250 pci card reader. The card reader has
some problems with DDR50 mode, so add a new quirks2 for broken ddr50.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Chris Ball <chris@printf.net>
There are no reason to why the use of a non-volatile internal eMMC
cache should be controlled by a host cap. Instead let's just enable it
if the eMMC card supports it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Earlier we disabled the cache during suspend, which meant a flush was
internally at the eMMC performed as well.
To simplify code we can make use of the mmc_flush_cache(), during mmc
suspend, which makes the mmc_cache_ctrl() redundant so then we can
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
There are no active users of this host capability. The primary reason
for adding this cap was due to a bug in ux500 boot loader code, which
is not a relevant issue any more. So, let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
There is no need for keeping a host cap for MMC_CAP2_SANITIZE, instead
we just make the feature default available.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Invoking system suspend or shutdown without using the Kconfig option
MMC_UNSAFE_RESUME, did trigger an ungraceful power cut of the card.
To improve the situation, change the behavior to always make use of the
available bus_ops callbacks that handles system suspend and shutdown
properly.
By changing the behavior MMC_UNSAFE_RESUME becomes redundant, so lets's
remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Core:
- Avoid get_cd() on cards marked nonremovable.
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC.
- dwmmc: Support Hisilicon K3 SoC controllers.
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM.
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540.
- tegra: Support Tegra124 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wZBx
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.14:
Core:
- Avoid get_cd() on cards marked nonremovable
Drivers:
- arasan: New driver for controllers found in e.g. Xilinx Zynq SoC
- dwmmc: Support Hisilicon K3 SoC controllers
- esdhc-imx: Support for HS200 mode, DDR modes on MX6, runtime PM
- sdhci-pci: Support O2Micro/BayHubTech controllers used in laptops
like Lenovo ThinkPad W540, Dell Latitude E5440, Dell Latitude E6540
- tegra: Support Tegra124 SoCs"
* tag 'mmc-updates-for-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (55 commits)
mmc: sdhci-pci: Fix possibility of chip->fixes being null
mmc: sdhci-pci: Fix BYT sd card getting stuck in runtime suspend
mmc: sdhci: Allow for long command timeouts
mmc: sdio: add a quirk for broken SDIO_CCCR_INTx polling
mmc: sdhci: fix lockdep error in tuning routine
mmc: dw_mmc: k3: remove clk_table
mmc: dw_mmc: fix dw_mci_get_cd
mmc: dw_mmc: fix sparse non static symbol warning
mmc: sdhci-esdhc-imx: fix warning during module remove function
mmc: sdhci-esdhc-imx: fix access hardirq-unsafe lock in atomic context
mmc: core: sd: implement proper support for sd3.0 au sizes
mmc: atmel-mci: add vmmc-supply support
mmc: sdhci-pci: add broken HS200 quirk for Intel Merrifield
mmc: sdhci: add quirk for broken HS200 support
mmc: arasan: Add driver for Arasan SDHCI
mmc: dw_mmc: add dw_mmc-k3 for k3 platform
mmc: dw_mmc: use slot-gpio to handle cd pin
mmc: sdhci-pci: add support of O2Micro/BayHubTech SD hosts
mmc: sdhci-pci: break out definitions to header file
mmc: tmio: fixup compile error
...
Conflicts:
MAINTAINERS
Polling SDIO_CCCR_INTx could create a fake interrupt with Marvell
SD8797 card. Add a quirk to handle this case. The fixup here is
to issue a dummy CMD52 read to function 0 register 0xff, and this
dummy read must be right after SDIO_CCCR_INTx is read.
Patch has been verified on a dw_mmc controller (Samsung Chromebook)
with MMC_CAP_SDIO_IRQ disabled.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Paul Stewart <pstew@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
One of Renesas SDHI chip needs workaround to use it, and, we can judge
it based on chip version. This patch adds very quick-hack workaround
method, since we still don't know how many chips need workaround in
the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDIO identifier for Broadcom WLAN devices were defined in the
brcmfmac SDIO driver. Moving the definitions in MMC header file
seems common sense.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some environments it is to prefer to postpone the resume of the card
device until runtime_resume is being carried out, since it will mean a
signficant decrease of the total system resume time.
The reason of the decreased resume time is simply because of the actual
re-initalization of the card, which typically takes hundreds of
milliseconds, is performed outside the resume sequence and wont thus
affect it.
For removable card, the detect work tries to re-detect the card to make
sure it is still present, as a part of that sequence the card will also
be runtime_resumed and thus also fully resumed.
For a non-removable card, typically a mmc blk request will trigger a
runtime_resume and thus fully resume the card. This also means the
first request will likely suffer from an inital latency since the
re-initialization of the card needs to be performed.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
By adding a card state that records if it is suspended or resumed, we
can accept asyncronus suspend/resume requests for the mmc and sd
bus_ops.
MMC_CAP_AGGRESSIVE_PM, will at request inactivity through the runtime
bus_ops callbacks, execute a suspend of the the card. In the state were
this has been done, we can receive a suspend request for the mmc bus,
which for sd and mmc forced the card to active state by a
pm_runtime_get_sync. In other words, the card was resumed and then
immediately suspended again, completely unnecessary.
Since the suspend/resume bus_ops callbacks for sd and mmc are now
capable of handling asynchronous requests, we no longer need to force
the card to active state before executing suspend. Evidently preventing
the above sequence for MMC_CAP_AGGRESSIVE_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The are no more users of the deprecated mmc_suspend|resume_host API,
so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The negotiated ocr mask is directly related to the card. Once a card
gets removed, the mask shall be dropped. By moving the cache of the ocr
mask from the host struct to the card struct we have accomplished this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some switch operations like poweroff notify, shall according to the
spec not be followed by any other new commands. For these cases and
when the host does'nt support MMC_CAP_WAIT_WHILE_BUSY, we must not
send status commands to poll for busy detection. Instead wait for
the stated timeout from the EXT_CSD before completing the request.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In error cases, DTO interrupt may or may not be generated depending
on remained data. Stop/Abort command ensures DTO generation for that
situation. Currently if 'stop' field of data is empty, there is no
stop/abort command. So, it could hang waiting DTO. This change
reinforces these cases.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Read Threshold should be ensured that the card clock does not stop
in the middle of a block of data being transferred from the card to the
Host. Specially, clock stop is allowed in fast transfer such as HS200
or SDR104 mode. And so, it should be enabled.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This change helps to choose msize, rx_watermark and tx_watermark
depending on block size for IDMAC mode. For SDIO block size can be
variable, so if these values are set incorrectly, card clock may stop.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
cscope says there are no callers for mmc_try_claim_host in the kernel.
No reason to keep it.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We use host->ocr_mask to hold the voltage get from device-tree
node, In case host->ocr_mask was available, we use host->ocr_mask
as the final available voltage can be used by MMC/SD/SDIO card.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add function to support getting voltage from device-tree.
If voltage-range is specified in device-tree node, this function
will parse it and return the available voltage mask.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some newer MMCIF IP revisions contain a CE_CLK_CTRL2 register, that has to
be set for proper operation. Support for this feature is added in a way to
preserve the current behaviour by default, i.e. when it is not enabled
in platform data. Patch is based on work by Nobuyuki HIRAI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some earlier MMCIF IP revisions contained Command Completion Signal
support, which has been dropped again in modern versions. Sopport for
this feature is added in a way to preserve the current behaviour by
default, i.e. when it is not enabled in platform data. Patch is based
on work by Nobuyuki HIRAI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sh_dma.h isn't needed in sh_mmcif.h, move it into sh_mmcif.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The callback isn't used by the driver and isn't initialized by board
code. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The P2020 has a non-standard implementation of the SDHCI_HOST_CONTROL
register. This patch adds a QUIRK in the SDHCI header to signal that
a host controller has a non-standard SDHCI_HOST_CONTROL register. The
patch adds a check to the function esdhc_writeb in file
sdhci-of-esdhc.c, where it checks if the write is done to the
SDHCI_HOST_CONTROL register and th host has the above mentioned QUIRK,
then the function simply returns instead of writing to the register.
The patch also detects if the processor is P2020 (by looking in dev
tree) and if so, adds the QUIRK to the host->quirk2
Signed-off-by: Oded Gabbay <ogabbay@advaoptical.com>
Reviewed-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Although the HC supports HS200 (eMMC) the caps2 are always zero; this
means there's no way to use the super speed mode (when init the card).
If the HC support SDR104, for SD3.0, so it also supports HS200 for eMMC
and this patch just sets the MMC_CAP2_HS200 in the host caps2 field.
Reported-by: Youssef Triki <youssef.triki@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP2_FULL_PWR_CYCLE shall be set by host drivers which are able to
do a complete power cycle of the card. In the eMMC case that includes
both vcc and vccq.
This CAP is providing the protocol layer with important information,
needed to take optimized decisions during card initialization and in
the suspend/resume sequence.
MMC_CAP2_POWEROFF_NOTIFY is replaced by MMC_CAP2_FULL_PWR_CYCLE, since
it makes sense to use a wider scope for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Considering shutdown of the card, the responsibility to initate this
sequence shall be driven from the mmc_bus.
This patch enables the mmc_bus to handle this sequence properly. A new
.shutdown callback is added in the mmc_driver struct which is used to
shutdown the blk device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In addition to just logging errors encountered during DT parsing or
allocating GPIO slots for CD/WP, mmc_of_parse() now returns with an error.
In particular, this is needed if the GPIO allocation may return
EPROBE_DEFER.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If card power is dependent on SD bus power then the host controller
must not be runtime suspended while the card is powered up. Add
the ability to stay runtime-resumed in that case and enable it with a new
quirk SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the saved values in card->ext_csd when selecting power class.
By doing this the power class will be selected even if mmc_init_card
is called with oldcard != NULL, which is the case after a suspend/resume.
Today ext_csd is NULL if mmc_init_card is called with oldcard != NULL
and power class will not be selected.
According to the eMMC specification the POWER_CLASS value is reset after
power failure, H/W reset assertion and any CMD0 reset.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Acked By: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Aggressive power management is suitable when saving power is
essential. At request inactivity timeout, aka pm runtime
autosuspend timeout, the card will be suspended.
Once a new request arrives, the card will be re-initalized and
thus the first request will suffer from a latency. This latency
is card-specific, experiments has shown in general that SD-cards
has quite poor initialization time, around 300ms-1100ms. eMMC is
not surprisingly far better but still a couple of hundreds of ms
has been observed.
Except for the request latency, it is important to know that
suspending the card will also prevent the card from executing
internal house-keeping operations in idle mode. This could mean
degradation in performance.
To use this feature make sure the request inactivity timeout is
chosen carefully. This has not been done as a part of this patch.
Enable this feature by using host cap MMC_CAP_AGGRESSIVE_PM and
by setting CONFIG_MMC_UNSAFE_RESUME.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Once the mmc blkdevice is being probed, runtime pm will be enabled.
By using runtime autosuspend, the power save operations can be done
when request inactivity occurs for a certain time. Right now the
selected timeout value is set to 3 s. Obviously this value will likely
need to be configurable somehow since it needs to be trimmed depending
on the power save algorithm.
For SD-combo cards, we are still leaving the enablement of runtime PM
to the SDIO init sequence since it depends on the capabilities of the
SDIO func driver.
Moreover, when the blk device is being suspended, we make sure the device
will be runtime resumed. The reason for doing this is that we want the
host suspend sequence to be unaware of any runtime power save operations
done for the card in this phase. Thus it can just handle the suspend as
the card is fully powered from a runtime perspective.
Finally, this patch prepares to make it possible to move BKOPS handling
into the runtime callbacks for the mmc bus_ops. Thus IDLE BKOPS can be
accomplished.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously the MMC_CAP2_DETECT_ON_ERR was invented for detecting
slow card removal. In was never a realy good solution and a proper
fix has been merged using gpio debouncing instead. We remove this
cap in this patch.
Although when using polling card detect mode, the code invented for
MMC_CAP2_DETECT_ON_ERR is re-used to complete card removal in an
earlier phase. There are no need waiting for the polling timeout to
elapse in this case.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull LED subsystem updates from Bryan Wu:
- move LED trigger drivers into a new directory
- lp55xx common driver updates
- other led drivers updates and bug fixing
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: leds-asic3: switch to using SIMPLE_DEV_PM_OPS
leds: leds-bd2802: add CONFIG_PM_SLEEP to suspend/resume functions
leds: lp55xx: configure the clock detection
leds: lp55xx: use common clock framework when external clock is used
leds: leds-ns2: fix oops at module removal
leds: leds-pwm: Defer led_pwm_set() if PWM can sleep
leds: lp55xx: fix the sysfs read operation
leds: lm355x, lm3642: support camera LED triggers for flash and torch
leds: add camera LED triggers
leds: trigger: use inline functions instead of macros
leds: tca6507: Use of_match_ptr() macro
leds: wm8350: Complain if we fail to reenable DCDC
leds: renesas: set gpio_request_one() flags param correctly
leds: leds-ns2: set devm_gpio_request_one() flags param correctly
leds: leds-lt3593: set devm_gpio_request_one() flags param correctly
leds: leds-bd2802: remove erroneous __exit annotation
leds: atmel-pwm: remove erroneous __exit annotation
leds: move LED trigger drivers into new subdirectory
leds: add new LP5562 LED driver
Commit fa5501890d introduced a performance
regression by adding mmc_power_up() to mmc_start_host(). mmc_power_up()
is not necessary to host controller initialization, it is part of card
initialization and is performed anyway asynchronously.
This patch allows a driver to leave the power up in asynchronous code
(as it was before).
On my current target platform this reduces driver initialization from:
[ 1.313220] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 102008 usecs
to this:
[ 1.217209] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 8331 usecs
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Macros are used in case that an inline function doesn't work.
Otherwise, use an empty inline function.
(a) Case of !CONFIG_LEDS_TRIGGERS
Following macros are replaced with inline functions.
led_trigger_register_simple()
led_trigger_unregister_simple()
led_trigger_event()
To make inline types, the structure, 'led_trigger' should be defined.
This structure has no member at all.
(b) Case of !CONFIG_LEDS_TRIGGER_IDE_DISK
ledtrig_ide_activity() macro is replaced with an inline function as well.
(c) DEFINE_LED_TRIGGER() and DEFINE_LED_TRIGGER_GLOBAL()
Struct 'led_trigger' is defined both cases, with CONFIG_LEDS_TRIGGERS and
without CONFIG_LEDS_TRIGGERS.
Those macros are moved out of CONFIG_LED_TRIGGERS because of no-dependency
on CONFIG_LEDS_TRIGGERS.
(d) Fix build errors in mmc-core driver
After replacing macros with inline functions, following build errors occur.
(condition: CONFIG_LEDS_TRIGGERS is not set)
drivers/mmc/core/core.c: In function 'mmc_request_done':
drivers/mmc/core/core.c:164:25: error: 'struct mmc_host' has no member named 'led'
drivers/mmc/core/core.c: In function 'mmc_start_request':
drivers/mmc/core/core.c:254:24: error: 'struct mmc_host' has no member named 'led'
make[3]: *** [drivers/mmc/core/core.o] Error 1
The reason of these errors is non-existent member variable, 'led'.
It is only valid when CONFIG_LEDS_TRIGGERS is set.
But now, it can be used without this dependency.
To fix build errors, member 'led' is always used without its config option in
'include/linux/mmc/host.h'.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word - function number
This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The JEDEC MMC v4 spec defines a new PRV value in place of the original
fwrev and hwrev specified in v1. We can expose this in the kernel to enable
user space to more easily determine the product revision of a given MMC.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "extern" keyword isn't required in function declarations, remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds packed command feature of eMMC4.5. The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This host_ops member is used to test if the card is signaling busy by
pulling dat[0:3] low.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'. The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level). A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect. This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).
The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line. On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
When current request is running on the bus and if next request fetched
by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the
current request completes. This means that if new request comes in while
the mmcqd thread is blocked, this new request can not be prepared in
parallel to current ongoing request. This may result in delaying the new
request execution and increase it's latency.
This change allows to wake up the MMC thread on new request arrival.
Now once the MMC thread is woken up, a new request can be fetched and
prepared in parallel to the current running request which means this new
request can be started immediately after the current running request
completes.
With this change read throughput is improved by 16%.
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to UHS-I initialization sequence for SDIO 3.0 cards,
the host must set bit[24] (S18R) of OCR register during OCR
handshake to know whether the SDIO card is capable of doing
1.8V I/O.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block") area
by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports that it
supports 1.8V but the board itself has no way to switch to 1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite loop
while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQxpwoAAoJEHNBYZ7TNxYMir0P/in5xv6vVq+06hMb9JTA2+M0
+eSgNAoSQt3Zn3dTxGtcaMbrnVvegMD2sRmnHncSKoi6iUgWh7RhuT7o8vp2zgJe
KbuOF/OF5+RSnLwgCMcOCjauhBtHO7s+NPNbUH4DMN2/xQ7fpiY+QIsxrKWtImyO
E4v62zRm/6aa1IfGDgYTAlX8Y1QfEQhH55OYrF9UzU1m7TKsSGxYTXwx+LeLQZQ0
j6HO+FVlmu5jbZ4V69z3qNIdiklRGQBE7D+7cJqW6btv7x4oLmyygEoNA8M8ncxX
g5BD5oEt9oxW5OW8hYcEJ/flDErgekZekH8n+fZoNVDVq8gMJxHOV73mnN+wxRnd
lRGLhniVOzl4cU+ObcYTBzdUV+2yR3sRHSK8nwtb+HFATetM70gBlpoWni1+sGr5
qvFhnpzNrj0xCwoQpLerwrvCwPpyko9uxZQwO51HqhugFwWlJuTqQsnCgj+Q4MDE
CRUq4R6TCH7oMGeGin0qyD7jyigDnh7g4pPNQmuIYJSLsDwvinisz98MQ0XC8szc
Z1H9YXKch2woLHLPFWzNyAIlJWHXakjk5vb9uSQmkUIto/y7q+LiGVCc5uvny3rU
pJmda+U/8R8YmSWS7pUi6OmPRfcnPuAIllEwo3lBypVpdP/fcZ6aribrbGEo6DLb
XLFIHnl3O9/sjfUcMl+L
=oSX3
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.8:
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block")
area by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports
that it supports 1.8V but the board itself has no way to switch to
1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite
loop while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices
now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."
* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
mmc: sdhci: implement the .card_event() method
mmc: extend the slot-gpio card-detection to use host's .card_event() method
mmc: add a card-event host operation
mmc: sdhci-s3c: Fix compilation warning
mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
mmc: sdhci-dove: use devm_clk_get()
mmc: eSDHC: Recover from ADMA errors
mmc: dw_mmc: remove duplicated buswidth code
mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
mmc: Limit MMC speed to 52MHz if not HS200
mmc: dw_mmc: use devres functions in dw_mmc
mmc: sh_mmcif: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: fix clock frequency printing
mmc: Remove redundant null check before kfree in bus.c
mmc: Remove redundant null check before kfree in sdio_bus.c
mmc: sdhci-imx-esdhc: use more devm_* functions
mmc: dt: add no-1-8-v device tree flag
...
Some hosts need to perform additional actions upon card insertion or
ejection. Add a host operation to be called from card detection handlers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The OLPC XO-1.75 laptop includes a SDHCI controller which is 1.8v
capable, and it truthfully reports so in its capabilities. This
alternate voltage is used for driving new "UHS-I" SD cards at their
full speed.
However, what the controller doesn't know is that the motherboard
physically doesn't have a 1.8v supply available.
Add a quirk so that systems such as this one can override disable
1.8v support, adding support for UHS-I cards (by running them at
3.3v).
This avoids a problem where the system would first try to run the
card at 1.8v, fail, and then not be able to fully reset the card
to retry at the normal 3.3v voltage.
This is more appropriate than using the MISSING_CAPS quirk, which
is intended for cases where the SDHCI controller is actually lying
about its capabilities, and would force us to somehow override both
caps words from another source.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Philip Rakity <prakity@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add dt-based retrieval of host sdio pm capabilities. Based on
the dt based discovery do a bus init in the resume function.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide support for automatically sending Set Block Count
(CMD23) messages. Used at least for RPMB support.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Following JEDEC standard, if the mmc supports RPMB partition,
a new interface is created and exposed via /dev/block.
Users will be able to access RPMB partition using standard
mmc IOCTL commands.
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Loic Pallardy <loic.pallardy@stericsson.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Both of MMC_TIMING_LEGACY and MMC_TIMING_UHS_SDR12 are defined
to 0. And ios->timing is set to MMC_TIMING_LEGACY during power up.
But set_ios can't distinguish these two timing if host support
spec 3.0. Just adjust timing values to be different can resolve
this issue without any other impact.
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are discrepancies with regards to how MMC capabilities
are carried throughout the subsystem. Let's standardise them
to eliminate any confusion.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
All MXS users have been converted to device tree and the board files have
been removed.
No need to keep platform data in the driver.
Also move bus_width declaration in the beggining of mxs_mmc_probe() to
avoid: 'warning: ISO C90 forbids mixed declarations and code'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even though platform_get_irq returns error, 'host->irq'
always has an unsigned value. Less-than-zero comparison
of an unsigned value is never true. Type of 'unsigned int'
will be changed for 'int'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove non-UAPI Kbuild files that have become empty as a result of UAPI
disintegration. They used to have only header-y lines in them and those have
now moved to the Kbuild files in the corresponding uapi/ directories.
Possibly these should not be removed but rather have a comment inserted to say
they are intentionally left blank. This would make it easier to add generated
header lines in future without having to restore the infrastructure.
Note that at this point not all the UAPI disintegration parts have been merged,
so it is likely that more empty Kbuild files will turn up.
It is probably necessary to make the files non-empty to prevent the patch
program from automatically deleting them when it reduces them to nothing.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes up the broken suspend sequence for eMMC with sleep
support. Additionally it reworks the eMMC4.5 Power Off Notification
feature so it fits together with the existing sleep feature.
The CMD0 based re-initialization of the eMMC at resume is re-introduced
to maintain compatiblity for devices using sleep.
A host shall use MMC_CAP2_POWEROFF_NOTIFY to enable the Power Off
Notification feature. We might be able to remove this cap later on,
if we think that Power Off Notification always is preferred over
sleep, even if the host is not able to cut the eMMC VCCQ power.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Saugata Das <saugata.das@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung Exynos SoC's extend the dw-mshc controller for additional clock
and bus control. Add support for these extensions and include provide
device tree based discovery suppory as well.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The core dw-mshc controller driver can let platform specific
implementations of the dw-mshc controller to control the hardware
as required by such implementations. This is acheived by invoking
implementation specific (optional) callbacks. Define the list of
callbacks supported the add invocation points for the same.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the write protect pad of the controller is not connected to the write
protect pin of the slot, the driver should be notified of this condition
so that incorrect check for write protection by reading the WRTORT
register can avoided. The get_ro platform callback can be used for in
such cases, but with device tree support enabled, such platform callbacks
cannot be supported.
Add a new quirk for notifying the driver about the missing write protect
line so the driver can assume that the card write protection is disabled.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some platforms allow for clock gating and control of bus interface unit
clock and card interface unit clock. Add support for clock lookup of
optional biu and ciu clocks for clock gating and clock speed
determination.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The 'struct dw_mci' maintains a copy of the pdev->dev instance instead of
maintaining a reference to that 'struct device' instance. Any resource
allocated using the device resource management kernel API with the instance
of 'struct device' in 'struct dw_mci' is then incorrect. Fix this by
converting the copy of 'struct device' in 'struct dw_mci' to a reference.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable eMMC background operations (BKOPS) feature.
If URGENT_BKOPS is set after a response, note that BKOPS are required.
Immediately run BKOPS if required. Read/write operations should be
requested during BKOPS(LEVEL-1), then issue HPI to interrupt the
ongoing BKOPS and service the foreground operation.
(This patch only controls the LEVEL2/3.)
When repeating the writing 1GB data, at a certain time, performance is
decreased. At that time, card triggers the Level-3 or Level-2. After
running bkops, performance is recovered.
Future considerations:
* Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner.
* Interrupt ongoing BKOPS before powering off the card.
* How do we get BKOPS_STATUS value (periodically send ext_csd command)?
* If using periodic bkops, also consider runtime_pm control.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some systems the host controller does not support vccq
signaling. This is supplied by a dedicated regulator (vqmmc).
Add support for this regulator.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
References:
http://forum.xda-developers.com/showthread.php?t=1644364https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkB
Signed-off-by: Ian Chen <ian.cy.chen@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@vger.kernel.org> [3.0+]
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull slave-dmaengine update from Vinod Koul:
"This time we have a new dmaengine driver from the tegra folks. Also
we have Guennadi's cleanup of sh drivers which incudes a library for
sh drivers. And the usual odd fixes in bunch of drivers and some nice
cleanup of dw_dmac from Andy."
Fix up conflicts in drivers/mmc/host/sh_mmcif.c
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Cleanup logging messages
mmc: sh_mmcif: switch to the new DMA channel allocation and configuration
dma: sh: provide a migration path for slave drivers to stop using .private
dma: sh: use an integer slave ID to improve API compatibility
dmaengine: shdma: prepare to stop using struct dma_chan::private
sh: remove unused DMA device pointer from SIU platform data
ASoC: siu: don't use DMA device for channel filtering
dmaengine: shdma: (cosmetic) simplify a static function
dmaengine: at_hdmac: add a few const qualifiers
dw_dmac: use 'u32' for LLI structure members, not dma_addr_t
dw_dmac: mark dwc_dump_lli inline
dma: mxs-dma: Export missing symbols from mxs-dma.c
dma: shdma: convert to the shdma base library
ASoC: fsi: prepare for conversion to the shdma base library
usb: renesas_usbhs: prepare for conversion to the shdma base library
ASoC: siu: prepare for conversion to the shdma base library
serial: sh-sci: prepare for conversion to the shdma base library
mmc: sh_mobile_sdhi: prepare for conversion to the shdma base library
mmc: sh_mmcif: remove unneeded struct sh_mmcif_dma, prepare to shdma conversion
dma: shdma: prepare for conversion to the shdma base library
...
Host has different current capabilities at different voltages, we need
to record these settings seperately. The defined voltages are 1.8/3.0/3.3.
For other voltages, we do not touch current limit setting.
Before we set the current limit for the sd card, find out the host's
operating voltage first and then find out the current capabilities of
the host at that voltage to set the current limit.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a new flag of SDHCI_USING_RETUNING_TIMER to represent if the host
is using a retuning timer for the card inserted.
This flag is set when the host does tuning the first time for the card
and the host's retuning mode is 1. This flag is used afterwards whenever
needs to decide if the host is currently using a retuning timer.
This flag is cleared when the card is removed in sdhci_reinit.
The set/clear of the flag and the start/stop of the retuning timer is
associated with the card's init/remove time, so there is no need to
touch it when the host is to be removed as at that time the card should
have already been removed.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently only the capability_0 register can be set if
SDHCI_QUIRK_MISSING_CAPS is defined. This is a problem when
the capability_1 register also needs changing. Use the quirk
SDHCI_QUIRK_MISSING_CAPS to allow both registers to be set.
Redefining caps[1] is useful when the board design does not
support 1.8v vccq so UHS modes are not available. The code that
calls sdhci_add_host can then detect this condition and adjust
the caps so the UHS mode will not be attempted on UHS cards.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
max_current_caps can return 0 if not available from the sd controller.
If no regulator is present or the regulator specifies a current
less then 200ma, we no longer still set the 200mA caps bit anyway.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Aaron Lu <aaron_lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Extend the sh_mmcif driver to support GPIO card detection, provided by the
slot function module. The original .get_cd() platform callback is also
preserved for now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Let SDHI platforms specify mmc_host::caps2 flags in their platform data.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Card Write-Protect pin is often implemented, using a GPIO, which makes
it simple to provide a generic handler for it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This prepares for the addition of further slot functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A simple extension of mmc slot functions add support for CD GPIO polling
for cases where the GPIO cannot produce interrupts, or where this is not
desired for some reason.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
To handle CD and WP SD/MMC slot pins we need generic flags to specify their
polarity.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
struct mmc_host::hotplug is becoming a generic hook for slot functions.
Rename it accordingly.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a function to get regulators, supplying card's Vdd and Vccq on a
specific host. If a Vdd supplying regulator is found, the function checks,
whether a valid OCR mask can be obtained from it. The Vccq regulator is
optional. A failure to get it is not fatal.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that all users have been updated to use the embedded in struct
sh_mmcif_plat_data DMA slave IDs, struct sh_mmcif_dma is no longer needed
and can be removed. This also makes preparation to the shdma base library
conversion easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SDIO_CCCR_IF[1:0] in SDIO card is used for card data bus width
setting as below:
00b: 1-bit bus
01b: Reserved
10b: 4-bit bus
11b: 8-bit bus (only for embedded SDIO)
And sdio_enable_wide is for setting data bus width as 4-bit.
But currently, it first reads the register, second OR' 1b with
SDIO_CCCR_IF[1], and then writes it back.
As we can see, this is based on such assumption that the
SDIO_CCCR_IF[0] is always 0. Apparently, this is not right.
Signed-off-by: Yong Ding <yongd@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuex7AAoJEIwa5zzehBx3xsQP/jkyt74MvuKUi8pi2zkeMIgn
4XieyqcA0KZjJzfB22q3GIZjNIf/mEIGE4E/3bneVMPh/E2zaiohaXFExBmjNjml
hhzWeZlFGPBjrZsfpIXJIIUhwSI7gX2rjYh4npJmdNhZmy8Y89XnpNJhN1kOwMuV
oN23hPWoSVGbyDMQ0fmHx9GyOL8m7yap+joG13aljDa2OKpQg+pYvdwft+k1K9di
8yPF+qA043UUR7dSsjmTbiCcjZy2eySdCmfOAkEG4inSgxNoM7GBs3MuwZo/veCD
v5WssJqWDbLXtqKn5Uo2bvGWiEcf0xtwOAqhSpbaup3dQFJSWMEenBTtA9UlxFhk
6gdY62O+7k6N0thkxXyLNGkgaGzexZAsK7dM6XSDB+PqD+OSNJS7dvmxZM8tuaRn
rvCM1XWcNeN/dpnLbgwCR12efkwWtJoqqUZUUp/tFFaTo8HriqeAIYk7obnR8s9n
S5x9LeueQGNgaxXJzVdh481YKG/1lqjG/a06HbVgYS4XQvtdA+4khalOefJv10tm
Nkg8+4/8pMthWJfhhlfPUgWFXOXFF2AGPG4su2XwKuFXypO8599lzi7gUQaEZu2U
7caqoWP69KsKvK5iAAmA4DQ2rcsgHd44NXx/8Jjes9ma8knlYjrf42dBH6AZMQBG
69I9sJ1cyqusBwx72NPN
=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
Rename arch/arm/mach-mxs/include/mach/mmc.h to
include/linux/mmc/mxs-mmc.h, so that mxs-mmc driver becomes
<mach/*> inclusion free.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Chris Ball <cjb@laptop.org>
The variable 'dw_mci_card_workqueue' is a global variable shared between
multiple instances of the dw_mmc host controller. Due to this, data
corruption has been noticed when multiple instances of dw_mmc controllers
are actively reading/writing the media. Fix this by adding a instance
of 'struct workqueue_struct' for each host instance and removing the
global 'dw_mci_card_workqueue' instance.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Current implementation decides the card type exclusively. Even though
eMMC device can support both HS200 and DDR mode, card type will be
set only for HS200. If the host doesn't support HS200 but has DDR
capability, then DDR mode can't be selected.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit 06e8935feb ("optimized SDIO IRQ handling for single irq")
introduced some spurious calls to SDIO function interrupt handlers,
such as when the SDIO IRQ thread is started, or the safety check
performed upon a system resume. Let's add a flag to perform the
optimization only when a real interrupt is signaled by the host
driver and we know there is no point confirming it.
Reported-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC bus is using legacy suspend/resume method, which is not compatible if
runtime pm callbacks are used. In this scenario, MMC bus suspend/resume
callbacks cannot be called when system entering S3. So change to use the
new defined dev_pm_ops for system sleeping mode.
Tested on AM335x Platform. Solves major issue/crash reported at
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Tested-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ulf Hansson