- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=b0/p
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
MMC core:
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
* tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc: (68 commits)
mmc: dw_mmc: remove the deprecated "supports-highspeed" property
mmc: dw_mmc: minor cleanup for dw_mci_adjust_fifoth
mmc: dw_mmc: use macro to define ring buffer size
mmc: dw_mmc: fix misleading error print if failing to do DMA transfer
mmc: dw_mmc: avoid race condition of cpu and IDMAC
mmc: dw_mmc: split out preparation of desc for IDMAC32 and IDMAC64
mmc: core: don't try to switch block size for dual rate mode
mmc: sdhci-of-arasan: Set controller to test mode when no CD bit
dt: sdhci-of-arasan: Add device tree option xlnx, fails-without-test-cd
mmc: tmio: add eMMC support
mmc: rtsx_usb: use new macro for R1 without CRC
mmc: rtsx_pci: use new macro for R1 without CRC
mmc: add define for R1 response without CRC
mmc: card: do away with indirection pointer
mmc: sdhci-acpi: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci-pci: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci: Support cap_cmd_during_tfr requests
mmc: mmc_test: Add tests for sending commands during transfer
mmc: core: Add support for sending commands during data transfer
mmc: sdhci-brcmstb: Fix incorrect capability
...
The core uses it for polling. Give drivers a proper define handle this
case like for other response types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A host controller driver exposes its capability using caps flag
MMC_CAP_CMD_DURING_TFR. A driver with that capability can accept requests
that are marked mrq->cap_cmd_during_tfr = true. Then the driver informs the
upper layers when the command line is available for further commands by
calling mmc_command_done(). Because of that, the driver will not then
automatically send STOP commands, and it is the responsibility of the upper
layer to send a STOP command if it is required.
For requests submitted through the mmc_wait_for_req() interface, the caller
sets mrq->cap_cmd_during_tfr = true which causes mmc_wait_for_req() in fact
not to wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete by calling
mmc_wait_for_req_done() which is now exported.
For requests submitted through the mmc_start_req() interface, the caller
again sets mrq->cap_cmd_during_tfr = true, but mmc_start_req() anyway does
not wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete in the
normal way i.e. calling mmc_start_req() again.
Irrespective of how a cap_cmd_during_tfr request is started,
mmc_is_req_done() can be called if the upper layer needs to determine if
the request is done. However the appropriate waiting function (either
mmc_wait_for_req_done() or mmc_start_req()) must still be called.
The implementation consists primarily of a new completion
mrq->cmd_completion which notifies when the command line is available for
further commands. That completion is completed by mmc_command_done().
When there is an ongoing data transfer, calls to mmc_wait_for_req() will
automatically wait on that completion, so the caller does not have to do
anything special.
Note, in the case of errors, the driver may call mmc_request_done() without
calling mmc_command_done() because mmc_request_done() always calls
mmc_command_done().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Dwmmc host controller may in unknown state when entering kernel boot. One
example is when booting from eMMC, bootloader need initialize MMC host
controller into some state so it can read. In order to make sure MMC host
controller in a clean initial state, this reset support is added.
With this patch, a 'resets' property can be added into dw_mmc device
tree node. The hardware logic is: dwmmc host controller IP receives a reset
signal from a 'reset provider' (eg. power management unit). The 'resets'
property points to this reset signal. So, during dwmmc driver probe,
it can use this signal to reset itself.
Refer to [1] for more information.
[1] Documentation/devicetree/bindings/reset/reset.txt
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD Status register contains several important fields related to the
SD Card proprietary features.
Those fields may be used by user space applications for vendor specific
usage.
None of those fields are exported today by the driver to user space.
In this patch, we are reading the SD Status register and exporting
(using MMC_DEV_ATTR) the SD Status register to the user space.
Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver already supports the bcm4339 chipset but only for the variant
that shares the same modalias as the bcm4335, ie. sdio:c00v02D0d4335.
It turns out that there are also bcm4339 devices out there that have a
more distiguishable modalias sdio:c00v02D0d4339.
Reported-by: Steve deRosier <derosier@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host drivers which needs to valdiate for non-supported MMC
commands and returnn error code for such requests.
To improve and simplify the behaviour, let's invent MMC_CAP2_NO_MMC
which these host drivers can set to tell the mmc core to skip sending MMC
commands during card initialization.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the quirks flag. (DW_MCI_QUIRK_BROKEN_DTO)
For removing this, enabled the dto_timer by defaults.
It doesn't see any I/O performance degression.
In future, dwmmc controller should not use the quirks flag.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are host drivers which needs to valdiate for non-supported SD
commands and returnn error code for such requests.
To improve and simplify the behaviour, let's invent MMC_CAP2_NO_SD
which these host drivers can set to tell the mmc core to skip sending SD
commands during card initialization.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Certain Hynix eMMC 4.41 cards might get broken when HPI feature is used
and hence this patch disables the HPI feature for such buggy cards.
As some of the other features like BKOPs/Cache/Sanitize are dependent on
HPI feature, those features would also get disabled if HPI is disabled.
Signed-off-by: Pratibhasagar V <pratibha@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
[gdavis: Forward port and cleanup]
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Controllers use data strobe line to latch data from devices
under hs400 mode, but not for cmd line. So since emmc 5.1, JEDEC
introduces enhanced strobe mode for latching cmd response from
emmc devices to host controllers. This new feature is optional,
so it depends both on device's cap and host's cap to decide
whether to use it or not.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduce mmc-hs400-enhanced-strobe for platforms
which want to enable enhanced strobe function from DT if the
mmc host controller claims to support enhanced strobe.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zHa6
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.7 rc1. They are based on a
commit earlier in the merge window and have been tested in linux-next
for a while.
MMC core:
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly"
* tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-acpi: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: sdhci-pci: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: longer timeout for long read time quirk
mmc: dw_mmc: rockchip: Set the drive phase properly
mmc: dw_mmc: fix the wrong max_blk_size
mmc: dw_mmc-rockchip: add MMC_CAP_CMD23 capabilities
mmc: sdhci-acpi: Ensure connected devices are powered when probing
ACPI / PM: Export acpi_device_fix_up_power()
mmc: block: Pause re-tuning while switched to the RPMB partition
mmc: block: Always switch back to main area after RPMB access
mmc: core: Add a facility to "pause" re-tuning
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXNbEBAAoJEG4XJFUm622bKfAH/2CnQV7dBCT5QwEiKYoOdsCR
eTiH7OYjTPw/rjKaG3laFgFbecnfUnHoGt55WKqRY58JycLza+SPTTv57hFTnOl+
4kDhUEjUggxMs5BRb3H7wtcnQVs/pTkgqKqwUrmFNkG6idENQgorK6DG4SNCwIdf
JrmxiHcN73xSATxlduoA9bGpluW3OvnFfRrJfyT6UBWZaFqFe3qsoKDx08S2WU2z
kUI9ZUO9Ht7Q85QdLfPQI7xo54dXo9a+8v3yc7fNFbcu1s8cqeYuofXfypjK7H/B
DEY96mubDnmDt8YE8yR9wStVzTr5zf39urE3o+/xSKSKhQxmNo8+x2TBSm5nFSQ=
=0HKi
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-05-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* remove IWLWIFI_DEBUG_EXPERIMENTAL_UCODE kconfig option
* work for RX multiqueue continues
* dynamic queue allocation work continues
* add Luca as maintainer
* a bunch of fixes and improvements all over
brcmfmac
* add 4356 sdio support
ath6kl
* add ability to set debug uart baud rate with a module parameter
wil6210
* add debugfs file to configure firmware led functionality
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-tuning is not possible when switched to the RPMB
partition. However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.
To ensure that re-tuning can't be done for a short
while, add a facility to "pause" re-tuning.
The existing facility to hold / release re-tuning
is used but it also flags re-tuning as needed to cause
re-tuning before the next command (which will be the
switch to RPMB).
We also need to "unpause" in the recovery path, which
is catered for by adding it to mmc_retune_disable().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A few SH boards include the file but don't make use of it (no named
interrupts). The SDHI code removed support for this feature as well.
So, drop the references and ultimately remove the unneeded file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rich Felker <dalias@libc.org>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to have a public and private header file. Merge them
into a private one, so looking up symbols is less confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
EVENT_XFER_ERROR isn't been used now, so it can be removed.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Try to fix the warning reported by:
scripts/kernel-doc -man -v include/linux/mmc/dw_mmc.h > /dev/null
warning: No description found for parameter 'irq_lock'
warning: No description found for parameter 'stop_abort'
warning: No description found for parameter 'prev_blksz'
warning: No description found for parameter 'timing'
warning: No description found for parameter 'ring_size'
warning: No description found for parameter 'dms'
warning: No description found for parameter 'phy_regs'
warning: No description found for parameter 'fifoth_val'
warning: No description found for parameter 'vqmmc_enabled'
warning: No description found for parameter 'cmd11_timer'
warning: Excess struct/union/enum/typedef member 'card_tasklet'
description in 'dw_mci'
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While here, refactor the comments so that they are before the
declaration they are referring to.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on work by Shinobu Uehara and Ben Dooks. This adds the voltage
switch operation needed for all UHS-I modes, but not the tuning needed
for SDR-104 which will come later.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mmc already use mmc_of_parse to get "broken-cd" property,
but it considered "broken-cd" to be a quirk in its driver. We
don't need this quirk here, and just take what we need from
mmc->caps.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch removes struct block_settings since
it's never used anywhere.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the indentation made the code awful to read. Fix that. Also,
introduce defines instead of magic hex values. Note that this includes
one change: We mask out know 0xff instead of 0x1ff. But 0x100 has always
been the clock enable bit. It doesn't make any sense to set it depending
on the clock calculation. Update copyright notices, too. I'll be working
on those files some more in the future.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's not set to MMC_DATA_STREAM anywhere.
It seems that it had been used with CMD11/CMD20.
But according to Spec, CMD11/CMD20 are obsolete command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver stores the physical address of the MMIO registers
in a pointer, which requires the use of type casts, and is actually
broken if anyone ever has this device on a 32-bit SoC in registers
above 4GB. Gcc warns about this possibility when the driver is built
with ARM LPAE enabled:
mmc/host/dw_mmc.c: In function 'dw_mci_edmac_start_dma':
mmc/host/dw_mmc.c:702:17: warning: cast from pointer to integer of different size
cfg.dst_addr = (dma_addr_t)(host->phy_regs + fifo_offset);
^
mmc/host/dw_mmc-pltfm.c: In function 'dw_mci_pltfm_register':
mmc/host/dw_mmc-pltfm.c:63:19: warning: cast to pointer from integer of different size
host->phy_regs = (void *)(regs->start);
This changes the code to use resource_size_t, which gets rid of the
warning, the bug and the useless casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch introduce a new MMC_CAP2_NO_SDIO cap used to tell the mmc
core to not send SDIO specific commands.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of checking for "#ifdef" directly in the code, let's invent a pair
of mmc core functions to deal with register/unregister the MMC PM notifier
block. Implement stubs for these functions when CONFIG_PM_SLEEP is unset,
as in that case the PM notifiers isn't used.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds logic to the MMC core to set VQMMC. This is expected to be
called by MMC drivers like dw_mmc as part of (or instead of) their
start_signal_voltage_switch() callback.
A few notes:
* When setting the signal voltage to 3.3V we do our best to make VQMMC
and VMMC match. It's been reported that this makes some old cards
happy since they were tested back in the day before UHS when VQMMC
and VMMC were provided by the same regulator. A nice side effect of
this is that we don't end up on the hairy edge of VQMMC (2.7V),
which some EEs claim is a little too close to the minimum for
comfort.
This is done in two steps. At first we try to find a VQMMC within
a 0.3V tolerance of VMMC and if this is not supported by the
supplying regulator we try to find a suitable voltage within the
whole 2.7V-3.6V area of the spec.
* The two step approach is currently necessary, as the used
regulator_set_voltage_triplet(min, target, max) uses a simple
implementation that just tries two basic steps:
regulator_set_voltage(target, max);
regulator_set_voltage(min, target);
So with only one step with 2.7-3.6V borders, if a suitable voltage
is a bit below VMMC, we would directly get the lowest 2.7V
which some boards (like Rockchips) don't like at all.
* When setting the signal voltage to 1.8V or 1.2V we aim for that
specific voltage instead of picking the lowest one in the range.
* We very purposely don't print errors in mmc_regulator_set_vqmmc().
There are cases where the MMC core will try several different
voltages and we don't want to pollute the logs.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_CLKGATE was once invented to save power by gating the bus clock at
request inactivity. At that time it served its purpose. The modern way to
deal with power saving for these scenarios, is by using runtime PM.
Nowadays, several host drivers have deployed runtime PM, but for those
that haven't and which still cares power saving at request inactivity,
it's certainly time to deploy runtime PM as it has been around for several
years now.
To simplify code to mmc core and thus decrease maintenance efforts, this
patch removes all code related to MMC_CLKGATE.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
As there are no users of the __mmc_switch() API, except for the mmc core
itself, let's convert it from an exported function into an internal.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some mass production of kingston eMMCs which adopt Phison's
firmware will meet an unrecoverable data conrruption occasionally
if performing trim due to a firmware bug confirmed by vendor. We
found it on Intel-C3230RK platform. So we add fixup of broken trim
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.
dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.
We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.
This means that host should get DRTO and DTO interrupt.
But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.
There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.
Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.
So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a
[ 4.991109] ------------[ cut here ]------------
[ 4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[ 4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM
because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.
Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the select_drive_strength callback to provide
drive strength selection for Intel SPT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add the ability to set eMMC driver strength
for HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporing drive strength selection
for eMMC, read the card's valid driver strengths.
Note that though the SD spec uses the term "drive strength",
the JEDEC eMMC spec uses the term "driver strength".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for adding drive strength support
for eMMC, add drive_strength to struct mmc_card
to record the card drive strength for UHS-I modes
and HS200 / HS400. For eMMC this will be needed
when switching between HS200 and HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In preparation for supporting also eMMC drive strength,
add the 'card' as a parameter so that the callback can
distinguish different types of cards if necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initialization of UHS-I modes for SD and SDIO cards
employs a callback to allow the host driver to
choose a drive strength value. Currently that
assumes the card drive strength and host driver
type must be the same value. Change to let the
callback make that decision and return both the
card drive strength and host driver type.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the new MMC_CAP2_NO_WRITE_PROTECT to let the core handle the case where
no write protect line is present instead of having custom driver code to
handle it.
dw_mci_of_get_slot_quirks() is slightly refactored to directly modify the
mmc_host capabilities instead of returning a quirk mask.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds