LS2088A and LS2080A are similar SoCs with a few differences like
ARM cores etc.
Reorganize the LS2080A device tree to move the common nodes to:
- fsl-ls208xa.dtsi
- fsl-ls208xa-rdb.dtsi
- fsl-ls208xa-qds.dtsi
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost) fully
supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier LS1043A
with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above
chips, there are only a few consumer devices and boards added
this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral support
for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom, Rockchip, Berlin,
and ZTE.
Conflicts:
- Documentation/devicetree/bindings/arm/shmobile.txt: a
rename/add conflict, keep both modifications and maintain
alphabetical ordering.
- arch/arm64/boot/dts/*/*.dtsi: nodes were added in netdev,
mmc and clk, keep both sides in each case.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=geT0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"A couple of interesting new SoC platforms are now supported, these are
the respective DTS sources:
- Samsung Exynos5433 mobile phone platform, including an (almost)
fully supported phone reference board.
- Hisilicon Hip07 server platform and D05 board, the latest iteration
of their product line, now with 64 Cortex-A72 cores across two
sockets.
- Allwinner A64 SoC, the first 64-bit chip from their "sunxi" product
line, used in Android tablets and ultra-cheap development boards
- NXP LS1046A Communication processor, improving on the earlier
LS1043A with faster CPU cores
- Qualcomm MSM8992 (Snapdragon 808) and MSM8994 (Snapdragon 810)
mobile phone SoCs
- Early support for the Nvidia Tegra Tegra186 SoC
- Amlogic S905D is a minor variant of their existing Android consumer
product line
- Rockchip PX5 automotive platform, a close relative of their popular
rk3368 Android tablet chips
Aside from the respective evaluation platforms for the above chips,
there are only a few consumer devices and boards added this time:
- Huawei Nexus 6P (Angler) mobile phone
- LG Nexus 5x (Bullhead) mobile phone
- Nexbox A1 and A95X Android TV boxes
- Pine64 development board based on Allwinner A64
- Globalscale Marvell ESPRESSOBin community board based on Armada 3700
- Renesas "R-Car Starter Kit Pro" (M3ULCB) low-cost automotive board
For the existing platforms, we get bug fixes and new peripheral
support for Juno, Renesas, Uniphier, Amlogic, Samsung, Broadcom,
Rockchip, Berlin, and ZTE"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (168 commits)
arm64: dts: fix build errors from missing dependencies
ARM64: dts: meson-gxbb: add SCPI pre-1.0 compatible
ARM64: dts: meson-gxl: Add support for Nexbox A95X
ARM64: dts: meson-gxm: Add support for the Nexbox A1
ARM: dts: artpec: add pcie support
arm64: dts: berlin4ct-dmp: add missing unit name to /memory node
arm64: dts: berlin4ct-stb: add missing unit name to /memory node
arm64: dts: berlin4ct: add missing unit name to /soc node
arm64: dts: qcom: msm8916: Add ddr support to sdhc1
arm64: dts: exynos: Enable HS400 mode for eMMC for TM2
ARM: dts: Add xo to sdhc clock node on qcom platforms
ARM64: dts: Add support for Meson GXM
dt-bindings: add rockchip RK1108 Evaluation board
arm64: dts: NS2: Add PCI PHYs
arm64: dts: NS2: enable sdio1
arm64: dts: exynos: Add the mshc_2 node for supporting T-Flash
arm64: tegra: Add NVIDIA P2771 board support
arm64: tegra: Enable PSCI on P3310
arm64: tegra: Add NVIDIA P3310 processor module support
arm64: tegra: Add GPIO controllers on Tegra186
...
Add the dts node for device configuration unit that provides
general purpose configuration and status for the device.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKrk2AAoJEFBXWFqHsHzOQlwH+wQXK2WABTOjRVchLOzup/cD
UtB7mbmXJrBSePa3OTvF8xMk4VFfjm9oljmLnUEnzWEfjsS2aURT2GJBWv/ddhqw
Mg/fYcZ1LgzJq8VOnenLpF1L2jc/I2hivCkBNmmkMK0HQvURKEAsdqNDc7Zg0meY
64qokll9Uz4DM2yeHkrUs9Q13UPs9/88ikYbE+CVDFaI0TCJjZUTImmjYkt8pJyk
poDtW6yE8ibMNk2DK4e4tthPRcYnhkFOtSJF6Qy6jouV/J9+aaKG5+rj4MBeF8Aj
T2+RFSQ4s2BuI5cH3qQq8Fv7lvF0Ay4wNWZl420R7shjbPWQNdIcbAbKL+51De0=
=jiir
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Freescale arm64 device tree updates for 4.10:
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
* tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add TMU device tree support for LS2080A
arm64: dts: ls1043a: Add TMU device tree support for LS1043A
arm64: dts: add LS1046A-QDS board support
Documentation: DT: Add entry for QorIQ LS1046A-QDS board
arm64: dts: add LS1046A-RDB board support
Documentation: DT: Add entry for QorIQ LS1046A-RDB board
arm64: dts: add QorIQ LS1046A SoC support
dt-bindings: ahci-fsl-qoriq: updated for SoC ls1046a
dt-bindings: qoriq-clock: add LS1043A/LS1046A/LS2080A compatible for clockgen
dt-bindings: i2c: adds two more nxp devices
dt-bindings: fsl: add LS1043A/LS1046A/LS2080A compatible for SCFG and DCFG
dt-bindings: fsl: Add LS1043A/LS1046A/LS2080A SoC compatible strings
Signed-off-by: Olof Johansson <olof@lixom.net>
Both the LS1043A and LS2080A platforms are affected by the Freescale
A008585 erratum. Advertise it in their respective device trees.
Signed-off-by: Scott Wood <oss@buserror.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull libata updates from Tejun Heo:
- Write same support added
- Minor ahci MSIX irq handling updates
- Non-critical SCSI command translation fixes
- Controller specific changes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: Revert "ahci: qoriq: Disable NCQ on ls2080a SoC"
libata: remove <asm-generic/libata-portmap.h>
libata: remove unused definitions from <asm/libata-portmap.h>
pata_at91: Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
ata: Replace BUG() with BUG_ON().
ata: sata_mv: Replacing dma_pool_alloc and memset with a single call dma_pool_zalloc.
libata: Some drives failing on SCT Write Same
ahci: use pci_alloc_irq_vectors
libata: SCT Write Same handle ATA_DFLAG_PIO
libata: SCT Write Same / DSM Trim
libata: Add support for SCT Write Same
libata: Safely overwrite attached page in WRITE SAME xlat
ahci: also use a per-port lock for the multi-MSIX case
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ahci: st: Add ports-implemented property in support
ahci: qoriq: enable snoopable sata read and write
ahci: qoriq: adjust sata parameter
libata-scsi: fix MODE SELECT translation for Control mode page
libata-scsi: use u8 array to store mode page copy
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The 'dma-coherent' indicates that the hardware IP block can ensure
the coherency of the data transferred from/to the IP block. This
can avoid the software cache flush/invalid actions, and improve
the performance significantly.
The PCI IP block of ls2080a has this capability, so adding this
feature to improve the PCI performance.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
By default the SATA IP on the qoriq SoCs does not generating
coherent/snoopable transactions. This patch enable it in the
sata axicc register.
In addition, the dma-coherent property must be set on the
SATA controller nodes.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Adds the cache nodes and next-level-cache property for the
cacheinfo to work.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MPIDR_EL1[63:32] value is equal to 0 for the CPUs of the LS1043A and
LS2080A SoCs. The ARM CPU binding allows #address-cells to be set to 1,
since MPIDR_EL1[63:32] bits are not used for CPUs identification. Update
the #address-cells and reg properties accordingly.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
updates to the fsl-mc node for full functionality:
-msi-parent is needed for interrupt support
-ranges is needed to enable the bus driver to translate bus addresses
-dpmac nodes provide a basis for relating dpmac objects to PHYs
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.
The chip-specific compatible "fsl,ls2080a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The arm64 device tree changes make up an increasing portion of
the overall changes, so they are kept separate from the 32-bit
devicetree changes and from the other arm64 updates.
Newly added SoCs and boards are:
- 96Boards Husky board
- AMD Overdrive board
- Amlogic S905 SoC and related Tronsmart boxes
- Annapurna Labs Alpine family and development board
- Broadcom Vulcan servers
- Broadcom Northstar 2 SoC
- Marvell Armada 3700 family and development board
- Qualcomm MSM8996 SoC
Additional devices are enabled for existing platforms from
Applied Micro, Hisilicon, Mediatek, Qualcomm, and Renesas and
there are a couple of other updates for Rockchip, Xilinx and
NXP/Freescale.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=izw3
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"The arm64 device tree changes make up an increasing portion of the
overall changes, so they are kept separate from the 32-bit devicetree
changes and from the other arm64 updates.
Newly added SoCs and boards are:
- 96Boards Husky board
- AMD Overdrive board
- Amlogic S905 SoC and related Tronsmart boxes
- Annapurna Labs Alpine family and development board
- Broadcom Vulcan servers
- Broadcom Northstar 2 SoC
- Marvell Armada 3700 family and development board
- Qualcomm MSM8996 SoC
Additional devices are enabled for existing platforms from Applied
Micro, Hisilicon, Mediatek, Qualcomm, and Renesas and there are a
couple of other updates for Rockchip, Xilinx and NXP/Freescale"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (102 commits)
ARM64: dts: amlogic: Add Tronsmart Vega S95 configs
Documentation: devicetree: amlogic: Document Tronsmart Vega S95 boards
ARM64: dts: Prepare configs for Amlogic Meson GXBaby
Documentation: devicetree: amlogic: Document Meson GXBaby
devicetree: bindings: Add vendor prefix for Tronsmart
arm64: dts: qcom: Fix MPP's function used for LED control
arm64: dts: alpine: add the MSIX node in the Alpine v2 dtsi
arm64: dts: add the Alpine v2 EVP
arm64: dts: marvell: re-order Device Tree nodes for Armada AP806
arm64: dts: marvell: update Armada AP806 clock description
arm64: dts: marvell: add Device Tree files for Armada 7K/8K
arm64: dts: apm: Add DT node for X-Gene v2 SLIMpro Mailbox I2C Driver
arm64: dts: apm: Mailbox device tree node for APM X-Gene v2 platform.
arm64: dts: apm: Add DT node for X-Gene v1 SLIMpro Mailbox I2C Driver
arm64: dts: apm: mailbox device tree node for APM X-Gene platform.
arm64: dts: apm: Update GPIO to control power-off on X-Gene v2 platforms
arm64: dts: apm: Update GPIO standby controller DT node for X-Gene v2 platforms
arm64: dts: apm: Update GPIO to control power-off on X-Gene v1 platforms
arm64: dts: salvator-x: enable USB 2.0 Host of channel 1 and 2
arm64: dts: salvator-x: enable usb2_phy of channel 1 and 2
...
The patch adds LS2085a to PCIe compatible to fix the compatibility
issue when using firmware with LS2085a compatible property.
Signed-off-by: Minghuan Lian <minghuan.lian@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4yG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"This is the first release where we split up the 64-bit contributions a
bit more, and in particular we are having a separate DT branch for
them.
Contents:
- New devices added to Broadcom NorthStar2
- Misc fixes for Exynos7 boards
- QCOM updates for MSM8916
- Rockchip tweaks for rk3368 SoC and eval board
- A series of fixes for APM X-Gene v1 and v2
- Renesas R8A7795 CPU/PSCI additions
- Marvell Berlin4CT PSCI, cpuidle, watchdog portions
- Freescale LS1043a SoC and dev board support
+ some treewide or other misc changes"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (104 commits)
dts/ls2080a: Update DTSI to add support of SP805 WDT
Documentation: DT: Add entry for ARM SP805-WDT
arm64: dts: X-Gene v2: I2C1 clock is always on
arm64: dts: X-Gene v1: I2C0 clock is always on
arm64: dts: Fix to use standard DT node names for X-Gene 1 and X-Gene 2 platforms
arm64: dts: hikey: add label properties to UARTs
arm64: dts: apq8016-sbc: add label properties for UART, I2C, and SPI
arm64: dts: apq8016-sbc: enable UART0 on LS connector
arm64: dts: juno: Add idle-states to device tree
arm64: dts: Added syscon-reboot node for FSL's LS2080A SoC
arm64: dts: add LS1043a-RDB board support
arm64: dts: add Freescale LS1043a SoC support
Documentation: DT: Add entry for Freescale LS1043a-RDB board
arm64: dts: uniphier: add PH1-LD10 SoC/board support
arm64: renesas: r8a7795: fix SATA clock assignment
arm64: dts: salvator-x: Enable SATA controller
arm64: dts: r8a7795: Add SATA controller node
arm64: renesas: r8a7795: add internal delay for i2c IPs
arm64: renesas: salvator-x: Add board part number to DT bindings
arm64: dts: r8a7795: Add pmu device nodes
...
This patch updates the LS2080a DTSI (DTS Include) file to add
support for eight SP805 Watchdog units which can be used to
reset the eight Cortex-A57 cores available on LS2080A.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added sys-reboot node to the FSL's LS2080A SoC DT to leverage
the ARM-generic reboot mechanism for this SoC. This mechanism
is enabled through CONFIG_POWER_RESET_SYSCON.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6c ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Checkpatch complains about the text suggesting writing to
Free Software Foundation for GPLv2 license copy.
This patch removes the same from the .dtsi and .dts
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch updates the LS2080a DTSI (DTS Include) file to add
support for the following peripherals:
- USB 3.0 Host
- PMU
- CCN-504
- SATA
- SPI
- PCIe
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Freescale is renaming the LS2085A SoC to LS2080A. This patch
addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Abhimanyu Saini