Pull input layer updates from Dmitry Torokhov:
- a bunch of new drivers (DA9052/53 touchscreenn controller, Synaptics
Navpoint, LM8333 keypads, Wacom I2C touhscreen);
- updates to existing touchpad drivers (ALPS, Sntelic);
- Wacom driver now supports Intuos5;
- device-tree bindings in numerous drivers;
- other cleanups and fixes.
Fix annoying conflict in drivers/input/tablet/wacom_wac.c that I think
implies that the input layer device naming is broken, but let's see. I
brough it up with Dmitry.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: matrix-keymap - fix building keymaps
Input: spear-keyboard - document DT bindings
Input: spear-keyboard - add device tree bindings
Input: matrix-keymap - wire up device tree support
Input: matrix-keymap - uninline and prepare for device tree support
Input: adp5588 - add support for gpio names
Input: omap-keypad - dynamically handle register offsets
Input: synaptics - fix compile warning
MAINTAINERS: adjust input-related patterns
Input: ALPS - switch to using input_mt_report_finger_count
Input: ALPS - add semi-MT support for v4 protocol
Input: Add Synaptics NavPoint (PXA27x SSP/SPI) driver
Input: atmel_mxt_ts - dump each message on just 1 line
Input: atmel_mxt_ts - do not read extra (checksum) byte
Input: atmel_mxt_ts - verify object size in mxt_write_object
Input: atmel_mxt_ts - only allow root to update firmware
Input: atmel_mxt_ts - use CONFIG_PM_SLEEP
Input: sentelic - report device's production serial number
Input: tl6040-vibra - Device Tree support
Input: evdev - properly handle read/write with count 0
...
Move synaptics_invert_y() inside CONFIG_MOUSE_PS2_SYNAPTICS to get rid of
a compile warning when we don't select synaptics support.
drivers/input/mouse/synaptics.c:53:12: warning: ‘synaptics_invert_y’ defined but not used [-Wunused-function]
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of open-coded reporting number of fingers on the touchpad
let's use input_mt_report_finger_count() helper.
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds semi-MT support for ALPS v4 protocol touchpads.
It is based on the work by Seth Forshee for ALPS v3 and v4 protocol
support. Three packets are required to assemble and process the MT
data. ST events are reported at once to avoid latency. If there
were two contacts or more, report MT data instead of ST events.
Thanks to Seth Forshee for providing most of the code, guidance
and insight for producing this patch.
Signed-off-by: George Pantalos <gpantalos@gmail.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This driver adds support for the Synaptics NavPoint touchpad connected
to a PXA27x SSP port in SPI slave mode. The device emulates a mouse;
a tap or tap-and-a-half drag gesture emulates the left mouse button.
For example, use the xf86-input-evdev driver for an X pointing device.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Hardware since Cx supports an unique identity (used to identify OEM vendors
and released lot number) which is very helpful for diagnostic purpose.
This revision tries to make it as a part of driver boot up message.
Whilst here, also bumping fsp_drv_ver to acknowledge recent addition of
absolute coordinates output.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
My last patch fixing up the dev_* messages caused a compiler warning
accidentally for an unused variable. Fix this up, as it was my fault.
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously I had made the struct device point to the input device, but
after talking with Dmitry, he said that the USB device would make more
sense for this driver to point to. So converted it to use that instead.
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dbg() was a very old USB-specific macro that should no longer
be used. This patch removes it from being used in the driver
and uses dev_dbg() instead.
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should always reference the input device for dev_err(), not the USB
device. Fix up the places where I got this wrong.
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input fix from Dmitry Torokhov:
"A simple fix for a recent regression in Synaptics driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix regression with "image sensor" trackpads
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Henrik Rydberg <rydberg@euromail.se>
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Alessandro Rubini <rubini@ipvvis.unipv.it>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7968a5dd49
Input: synaptics - add support for Relative mode
Accidentally broke support for advanced gestures (multitouch)
on some trackpads such as the one in my ThinkPad X220 by
incorretly changing the condition for enabling them. This
restores it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: stable@kernel.org [3.3]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Pull input updates from Dmitry Torokhov:
"Just a few small fixes..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: da9052 - fix memory leak in da9052_onkey_probe()
Input: gpio_mouse - use linux/gpio.h rather than asm/gpio.h
Input: trackpoint - use psmouse_fmt() for messages
Input: elantech - v4 is a clickpad, with only one button
Input: elantech - reset touchpad before configuring it
Input: sentelic - filter taps in absolute mode
Input: tps6507x-ts - fix MODULE_ALIAS to match driver name
Direct usage of the asm include has long been deprecated by the
introduction of gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add pointer and buttonpad properties for v4 hardware.
Also, Jachiet reported that on Asus UX31, right button has no effect.
It turns out v4 has only one button, the right-button effect is
implemented with software when Windows driver is installed, or in
firmware when touchpad is in relative mode. So remove BTN_RIGHT
while at it.
Reported-by: Jachiet Louis <louis@jachiet.com>
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acer VH40 has a Fn key toggling the touchpad on and off, but it's
implemented in system firmware, and the EC chip has to receive
reset command to activate this function. Also when this machine
wakes up after resume, psmouse_reset is necessary to bring the
touchpad back on.
Signed-off-by: JJ Ding <jj_ding@emc.com.tw>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts the drivers in drivers/input/* to use
module_serio_driver() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Taps in absolute positioning single-finger mode are currently reported
as physical clicks by the driver. This should be handled by userspace,
not the kernel.
When a tap occurs, the FSP_PB0_LBTN bit is set, but the FSP_PB0_PHY_BTN
is not. We use this to filter out physical clicks from taps.
Signed-off-by: Oskari Saarenmaa <os@ohmu.fi>
Reviewed-by: Tai-hwa Liang <avatar@sentelic.com>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Improve code readability by converting yet another magic number into a
pre-defined constant.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Hooking multi-finger coordinates output with kernel multitouch library;
- Enabling absolute coordinates output for Cx+ hardware. The older hardware
performs much better in relative mode; thus relative mode related code
are preserved.
Part of the code is based on the work done by Oskari Saarenmaa <os@ohmu.fi>,
which was used to support the clickpad found on ASUS UX21/31 Ultrabook.
On the other hand, the FSP found on UX21/31 doesn't have hardware capability
register other than PnP ID, which means that we'll have to figure out an
alternative approach to identify such pad correctly; otherwise, blindly
adding INPUT_PROP_BUTTONPAD property may compatability issues amongst
existing FSPs.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Move event bits setup code into a separate function,
fsp_set_input_params(), so that we can perform hardware-specific settings
in the future;
- Take hardware version information into account when activating
protocol;
- Remove button information from boot message as it's somewhat confusing
and is only for internal processing. While there, also move button
retrieval code to be a part of protocol activation process.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch converts the drivers in drivers/input/* to use the
module_i2c_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make use of psmouse_activate() and psmouse_deactivate() from psmouse-base.c
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Other drivers duplicate this code; no sense in having it be private
to psmouse-base.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS touchpad detection fails if some buttons of ALPS are pressed.
The reason is that the "E6" query response byte is different from
what is expected.
This was tested on a Toshiba Portege R500.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
To simplify detection as a touchpad, inform userspace of the physical
properties of the device.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
[rydberg@euromail.se: conflict resolution]
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
This patch adds a driver for Synaptics USB touchpad or pointing stick
devices. These USB devices emulate an USB mouse by default, so one can
also use the usbhid driver. However, in combination with special user
space drivers this kernel driver allows one to customize the behaviour
of the device.
An extended version of this driver with support for the cPad background
display can be found at
<http://jan-steinhoff.de/linux/synaptics-usb.html>.
Signed-off-by: Jan Steinhoff <mail@jan-steinhoff.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: bcm5974 - set BUTTONPAD property
Input: serio_raw - return proper result when serio_raw_write fails
Input: serio_raw - really signal HUP upon disconnect
Input: serio_raw - remove stray semicolon
Input: revert some over-zealous conversions to module_platform_driver()
Some bcm5974 trackpads have a physical button beneath the physical surface.
This patch sets the property bit so user space applications can detect the
trackpad type and act accordingly.
Signed-off-by: Jussi Pakkanen <jussi.pakkanen@canonical.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Recent conversion to module_platform_driver() went a bit too far and
converted not only drivers that used platform_driver_register() but
also ones using platform_driver_probe(), breaking them in process.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
Linus Torvalds