If the eeprom key isn't valid, either a different (currently unknown) format
is used or the eeprom is corrupted.
In both cases it doesn't make sense to interpret the data.
Also print an error message.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code uses only a single debug level and all debug messages are
printed for i2c_debug >= 2 only. So debug level 1 is actually the same as
level 0, which is odd.
Users expect debugging messages to become enabled for anything else than
debug level 0.
Fix it and simplify the code a bit by printing the debug messages also at debug
level 1;
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reduces the number of characters/lines, unifies the code and improves readability.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is only a single place where the dprintk2 macro is used, so get rid of it.
[mchehab@redhat.com: fix checkpathc.pl complain:
ERROR: space prohibited before that close parenthesis ')']
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver has changed much, especially since kernel 3.8.
So it's time to bump the driver version.
Changes since kernel 3.8:
- converted the driver to videobuf2
- converted the driver to the v4l2-ctrl framework
- added USB bulk transfer support
- use USB bulk transfers by default for webcams (allows streaming from multiple devices at the same time)
- added image quality bridge controls: contrast, brightness, saturation, blue balance, red balance, sharpness
- removed dependency from module ir-kbd-i2c
- cleaned up the frame data processing code
- removed some unused/obsolete code
- made remote controls of devices with external (i2c) receiver/decoder work again
- fixed audio over USB for device "Terratec Cinergy 250"
- several v4l2 compliance fixes and improvements (including fixes for ioctls enabling/disabling)
- lots of further bug fixes and code improvements
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the image quality bridge controls contrast, brightness, saturation,
blue balance, red balance and sharpness.
These controls are enabled only if no subdevice provides them.
Tested with the following devices:
"Terratec Cinergy 200 USB"
"Hauppauge HVR-900"
"SilverCrest 1.3MPix webcam"
"Hauppauge WinTV USB2"
"Speedlink VAD Laplace webcam"
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The image quality default values will be used in at least two different places
and by using #defines we make sure that they are always consistent.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Output resolutions <=20% of the input resolution exceed the capabilities of the
scaler.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum supported scaling value for registers 0x30+0x31 (horizontal scaling)
and 0x32+0x33 (vertical scaling) is 0x3fff, which corresponds to 20% of the
input frame size.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoids registering a VBI device and streaming in VBI-mode if the device is a
camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_DBG_G_CHIP_IDENT is a "normal" and not an "advanced" debug functionality.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_device_disconnect() is called when the device is disconnected, so that the
v4l2-core rejects all ioctl calls.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tuner type is set by the v4l2-core based on the device type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vidioc_s_fmt_vbi_cap() is a 100% duplicate of vidioc_g_fmt_vbi_cap() and
therefore can be removed.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em28xx driver doesn't support the VIDIOC_G_CROP and VIDIOC_S_CROP ioctls,
so VIDIOC_CROPCAP is useless and has the potential to confuse applications,
because it can be interpreted as indicator for cropping support.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current code V4L2_BUF_TYPE_VIDEO_CAPTURE is accepted only, but for VBI
devices only buffer type V4L2_BUF_TYPE_VBI_CAPTURE is used/valid.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_PARM doesn't make sense for VBI device nodes, because we don't support
selecting the number of read buffers to use.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
function, use v4l2_disable_ioctl() to disable the ioctl VIDIOC_S_PARM if the
device is not a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -EINVAL inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_G_AUDIO and
VIDIOC_S_AUDIO if the device doesn't support audio.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Disable the ioctls VIDIOC_G_TUNER, VIDIOC_S_TUNER, VIDIOC_G_FREQUENCY and
VIDIOC_S_FREQUENCY for video and VBI devices without tuner.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of checking the device type and returning -ENOTTY inside the ioctl
functions, use v4l2_disable_ioctl() to disable the ioctls VIDIOC_QUERYSTD,
VIDIOC_G_STD and VIDIOC_S_STD if the device is a camera.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems to work just the same as older revisions.
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the conversion to videobuf2, some unnecessary calls of
em28xx_set_alternate() have been removed. It is now called at analog streaming
start only.
This has unveiled a bug that causes USB bulk transfers to fail with all urbs
having status -EVOERFLOW.
The reason is, that for bulk transfers usb_set_interface() needs to be called
even if the previous alt setting was the same (side note: bulk transfers seem
to work only with alt=0).
While it seems to be NOT necessary for isoc transfers, it's reasonable to just
call usb_set_interface() unconditionally in em28xx_set_alternate().
Also add a comment that explains the issue to prevent regressions in the future.
Cc: stable@vger.kernel.org # for 3.8
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bytesperline calculation was incorrect: it used the old width instead of
the provided width. Fixed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- move the bit shifting of width+height values inside the function
- fix the debug message format and output values
- add comment about the size limit (e.g. EM277x supports >2MPix)
- make void, because error checking is incomplete and we never check the
returned value (we would continue anyway)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove em28xx_i2c_ir_work() and check the device type in the common callback
function em28xx_ir_work() instead. Simplifies em28xx_ir_start().
Reduces the code size with a minor performance drawback.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set up the i2c_client locally in em28xx_i2c_ir_handle_key().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already have the key polling functions and the polling infrastructure in
em28xx-input, so we can easily get rid of the dependency on module ir-kbd-i2c.
For maximum safety, do not touch the key reporting mechanism for those devices.
Code size could be improved further but would have minor peformance impacts.
Tested with device "Terratec Cinergy 200 USB" (EM2800_BOARD_TERRATEC_CINERGY_200)
[mchehab@redhat.com: Fix two checkpatch.pl warnings:
ERROR: "foo * bar" should be "foo *bar" (line 465)
WARNING: kfree(NULL) is safe this check is probably not required (line 725)]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't report any key/scan codes or errors inside the key polling functions
for internal IR RC devices, just in the key handling fucntions.
Do the same for external devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Field 'old' of struct IR_i2c is used nowhere in module ir-kbd-i2c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remy Blank reported that audio over USB can be made working for the television
input if .amux is changed from EM28XX_AMUX_LINE_IN to EM28XX_AMUX_VIDEO.
An examination of his devices shows, that it is indeed supplied with an EM202
AC97 audio IC. We also use this setting for the Cinergy 200.
Remy Blank also provided the original version of this patch (many thanks !).
Fixes bug 14126 (see bug report for further device details).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Remy Blank <remy.blank@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that it uses videobuf2, em28xx can support DMABUF.
Tested with an HVR-950 on analog mode and a 2gen i5core machine
with an i915 graphics adapter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That fixes the following warning:
drivers/media/usb/em28xx/em28xx-video.c:611:5: warning: no previous prototype for 'em28xx_stop_streaming' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
EEPROMs are currently read in blocks of 16 bytes, but the em2800 is limited
to 4 bytes per read. All other chip variants support reading of max. 64 bytes
at once (according to the em258x datasheet; also verified with em2710, em2882,
and em28174).
Since em2800_i2c_recv_bytes() has been fixed to return with -EOPNOTSUPP when
more than 4 bytes are requested, EEPROM reading with this chip is broken.
It was actually broken before that change, too, it just didn't throw an error
because the i2c adapter silently returned trash data (for all reads >1 byte !).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- do not pass USB specific error codes to userspace/i2c-subsystem
- unify the returned error codes and make them compliant with
the i2c subsystem spec
- check number of actually transferred bytes (via USB) everywehere
- fix/improve debug messages
- improve code comments
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I2C_FUNC_SMBUS_EMUL includes flag I2C_FUNC_SMBUS_WRITE_BLOCK_DATA which signals
that up to 31 data bytes can be written to the ic2 client.
But the EM2800 supports only i2c messages with max. 4 data bytes.
I2C_FUNC_IC2 should be set if a master_xfer function pointer is provided in
struct i2c_algorithm.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Function em2800_i2c_recv_bytes() has 2 severe bugs:
1) It does not wait for the i2c read to complete before reading the received message content from the bridge registers.
2) Reading more than 1 byte doesn't work
The former can result in data corruption, the latter always does.
The rewritten code also superseds the content of function
em2800_i2c_check_for_device().
Tested with device "Terratec Cinergy 200 USB".
[mchehab@redhat.com: Fix CodingStyle issues]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The em2800 can transfer up to 4 bytes per i2c message.
All other em25xx/em27xx/28xx chips can transfer at least 64 bytes per message.
I2C adapters should never split messages transferred via the I2C subsystem
into multiple message transfers, because the result will almost always NOT be
the same as when the whole data is transferred to the I2C client in a single
message.
If the message size exceeds the capabilities of the I2C adapter, -EOPNOTSUPP
should be returned.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_key functions are independent from the selected protocol, so assign
them once only at device initialization.
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main purpose of this patch is to move the call of em28xx_release_resources()
after the call of em28xx_close_extension().
This is necessary, because some resources might be needed/used by the extensions
fini() functions when they get closed.
Also mark the device as disconnected earlier in this function and unify the
em28xx_uninit_usb_xfer() calls for analog and digital mode.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Frank Schaefer