Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that various triggers use led_blink_setup() from atomic
context, so we can't do a flush_work there. Flush is still needed for
slow LEDs, but we can move it to sysfs code where it is safe.
WARNING: inconsistent lock state
5.2.0-rc1 #1 Tainted: G W
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/1/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
000000006e30541b
((work_completion)(&led_cdev->set_brightness_work)){+.?.}, at:
+__flush_work+0x3b/0x38a
{SOFTIRQ-ON-W} state was registered at:
lock_acquire+0x146/0x1a1
__flush_work+0x5b/0x38a
flush_work+0xb/0xd
led_blink_setup+0x1e/0xd3
led_blink_set+0x3f/0x44
tpt_trig_timer+0xdb/0x106
ieee80211_mod_tpt_led_trig+0xed/0x112
Fixes: 0db37915d9 ("leds: avoid races with workqueue")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If userspace doesn't end the input with a newline (which can easily
happen if the write happens from a C program that does write(fd,
iface, strlen(iface))), we may end up including garbage from a
previous, longer value in the device_name. For example
# cat device_name
# printf 'eth12' > device_name
# cat device_name
eth12
# printf 'eth3' > device_name
# cat device_name
eth32
I highly doubt anybody is relying on this behaviour, so switch to
simply copying the bytes (we've already checked that size is <
IFNAMSIZ) and unconditionally zero-terminate it; of course, we also
still have to strip a trailing newline.
This is also preparation for future patches.
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Renaming a netdev-trigger-tracked interface was resulting in an
unbalanced dev_hold().
Example:
> iw phy phy0 interface add foo type __ap
> echo netdev > trigger
> echo foo > device_name
> ip link set foo name bar
> iw dev bar del
[ 237.355366] unregister_netdevice: waiting for bar to become free. Usage count = 1
[ 247.435362] unregister_netdevice: waiting for bar to become free. Usage count = 1
[ 257.545366] unregister_netdevice: waiting for bar to become free. Usage count = 1
Above problem was caused by trigger checking a dev->name which obviously
changes after renaming an interface. It meant missing all further events
including the NETDEV_UNREGISTER which is required for calling dev_put().
This change fixes that by:
1) Comparing device struct *address* for notification-filtering purposes
2) Dropping unneeded NETDEV_CHANGENAME code (no behavior change)
Fixes: 06f502f57d ("leds: trigger: Introduce a NETDEV trigger")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Allow initialization of delays used in timer trigger from Device
Tree property.
This is especially useful for embedded systems where the trigger might
be used early, before bringing up user-space.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Allow initialization of delays used in oneshot trigger from Device
Tree property.
This is especially useful for embedded systems where the trigger might
be used early, before bringing up user-space.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Allow initialization of pattern used in pattern trigger from Device Tree
property.
This is especially useful for embedded systems where the pattern trigger
would be used to indicate the process of boot status in a nice,
user-friendly blinking way. This initialization pattern will be used
till user-space is brought up and sets its own pattern, indicating the
boot status is for example finished.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This patch adds a new LED trigger for coupling the audio mixer change
with the LED on laptops or other devices. Currently there are two
trigger types, "audio-mute" and "audio-micmute".
The audio driver triggers the LED brightness change via
ledtrig_audio_set() call with the proper type (either mute or
mic-mute). OTOH, the consumers may call ledtrig_audio_get() for the
initial brightness value that may have been set by the audio driver
beforehand.
This new stuff will be used by HD-audio codec driver and some platform
drivers (thinkpad_acpi and dell-laptop, also upcoming huawei-wmi).
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We will meet below issue due to mutex_lock() is called in interrupt context.
The mutex lock is used to protect the pattern trigger data, but before changing
new pattern trigger data (pattern values or repeat value) by users, we always
cancel the timer firstly to clear previous patterns' performance. That means
there is no race in pattern_trig_timer_function(), so we can drop the mutex
lock in pattern_trig_timer_function() to avoid this issue.
Moreover we can move the timer cancelling into mutex protection, since there
is no deadlock risk if we remove the mutex lock in pattern_trig_timer_function().
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted
4.20.0-rc1-koelsch-00841-ga338c8181013c1a9 #171
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
[<c020f19c>] (unwind_backtrace) from [<c020aecc>] (show_stack+0x10/0x14)
[<c020aecc>] (show_stack) from [<c07affb8>] (dump_stack+0x7c/0x9c)
[<c07affb8>] (dump_stack) from [<c02417d4>] (___might_sleep+0xf4/0x158)
[<c02417d4>] (___might_sleep) from [<c07c92c4>] (mutex_lock+0x18/0x60)
[<c07c92c4>] (mutex_lock) from [<c067b28c>] (pattern_trig_timer_function+0x1c/0x11c)
[<c067b28c>] (pattern_trig_timer_function) from [<c027f6fc>] (call_timer_fn+0x1c/0x90)
[<c027f6fc>] (call_timer_fn) from [<c027f944>] (expire_timers+0x94/0xa4)
[<c027f944>] (expire_timers) from [<c027fc98>] (run_timer_softirq+0x108/0x15c)
[<c027fc98>] (run_timer_softirq) from [<c02021cc>] (__do_softirq+0x1d4/0x258)
[<c02021cc>] (__do_softirq) from [<c0224d24>] (irq_exit+0x64/0xc4)
[<c0224d24>] (irq_exit) from [<c0268dd0>] (__handle_domain_irq+0x80/0xb4)
[<c0268dd0>] (__handle_domain_irq) from [<c045e1b0>] (gic_handle_irq+0x58/0x90)
[<c045e1b0>] (gic_handle_irq) from [<c02019f8>] (__irq_svc+0x58/0x74)
Exception stack(0xeb483f60 to 0xeb483fa8)
3f60: 00000000 00000000 eb9afaa0 c0217e80 00000000 ffffe000 00000000 c0e06408
3f80: 00000002 c0e0647c c0c6a5f0 00000000 c0e04900 eb483fb0 c0207ea8 c0207e98
3fa0: 60020013 ffffffff
[<c02019f8>] (__irq_svc) from [<c0207e98>] (arch_cpu_idle+0x1c/0x38)
[<c0207e98>] (arch_cpu_idle) from [<c0247ca8>] (do_idle+0x138/0x268)
[<c0247ca8>] (do_idle) from [<c0248050>] (cpu_startup_entry+0x18/0x1c)
[<c0248050>] (cpu_startup_entry) from [<402022ec>] (0x402022ec)
Fixes: 5fd752b6b3 ("leds: core: Introduce LED pattern trigger")
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Check for zero duration before skipping step. This fixes pattern
echo "0 1000 10 2550 0 1000" > pattern
which should do [ .-xXx-.] but does [ Xx-.]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Suggested-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This patch adds a new LED trigger that LED device can configure
to employ software or hardware pattern engine.
Consumers can write 'pattern' file to enable the software pattern
which alters the brightness for the specified duration with one
software timer.
Moreover consumers can write 'hw_pattern' file to enable the hardware
pattern for some LED controllers which can autonomously control
brightness over time, according to some preprogrammed hardware
patterns.
Signed-off-by: Raphael Teysseyre <rteysseyre@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
to handle device attributes. Also make use of the module_led_trigger()
helper to simplify trigger registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Use the new module_led_trigger() helper. Also use
attribute support from the trigger core. Drop error message on
allocation failure as kzalloc() already screams loudly when failing. Use
wrappers to get and set trigger data.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
can handle device attributes now. This allows simplifying the driver
considerably. Note that .deactivate() is only called when .activate()
succeeded, so the check for .activated can go away in .deactivate().
Also make use of module_led_trigger() and the accessor function to get
and set trigger_data.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This removes some boilerplate from the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
can handle device attributes now. This allows simplifying the driver
considerably. Note that .deactivate() is only called when .activate()
succeeded, so the check for .activated can go away in .deactivate().
Also make use of module_led_trigger() and the accessor function to get
and set trigger_data.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
can handle device attributes now. This allows simplifying the driver
considerably. Note that .deactivate() is only called when .activate()
succeeded, so the check for .activated can go away in .deactivate().
Also make use of module_led_trigger() and do some minor coding style
improvements.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
can handle device attributes now. This allows simplifying the driver
considerably. Note that .deactivate() is only called when .activate()
succeeded, so the check for .activated can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
can handle device attributes now. This allows simplifying the driver
considerably. Note that .deactivate() is only called when .activate()
succeeded, so the check for .trigger_data being non-NULL can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The trigger core learned error handling for the activate callback and
can handle device attributes now. This allows simplifying the driver
considerably. Note that .deactivate() is only called when .activate()
succeeded, so the check for trigger_data being non-NULL can go away.
(It was broken before because the core didn't clear .trigger_data, so it
might have been non-NULL even if .activate() failed before.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Given that activating a trigger can fail, let the callback return an
indication. This prevents to have a trigger active according to the
"trigger" sysfs attribute but not functional.
All users are changed accordingly to return 0 for now. There is no intended
change in behaviour.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
These files are licensed under GPL version 2 only. So use "GPL v2"
instead of "GPL" (which means v2 or later).
Also remove an empty (but commented) line at the end of the license
header which nicely proves in the context that the drivers are really v2
only :-)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
All the triggers are defined in a big if LEDS_TRIGGERS...endif block.
So there is no need to let each driver depend on LEDS_TRIGGERS explicitly
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
get_monotonic_boottime() is deprecated, so let's convert this to
the simpler ktime_get_boot_ns().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This adds two new disk triggers for triggering on reads
and writes respectively, named "disk-read" and "disk-write".
The use case comes from working on the D-Link DNS-313 NAS
box. This features an RGB LED for disk activity. with
these two triggers I can couple the green LED to read
activity and the red LED to write activity, which gives
the appropriate user feedback about what is happening
on the disk. When tested it gave exactly the feedback
desired.
The in-kernel interface is simply changed to pass a bool
indicating if the activity is write activity and update
each trigger (and the composite "disk-activity" trigger)
depending on what is passed in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Replace GPL license statements with SPDX GPL-2.0 license identifiers
and correct the module license to GPLv2.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This commit introduces a NETDEV trigger for named device
activity. Available triggers are link, rx, and tx.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Fixes: 7df4f9a9f0 ("leds: ledtrig-activity: Add a system activity LED trigger")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=T2rn
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.15rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- add a driver for PC Engines APU/APU2 LEDs
New LED trigger:
- add a system activity LED trigger
LED core improvements:
- replace flags bit shift with BIT() macros
Convert timers to use timer_setup() in:
- led-core
- ledtrig-activity
- ledtrig-heartbeat
- ledtrig-transient
LED class drivers fixes:
- lp55xx: fix spelling mistake: 'cound' -> 'could'
- tca6507: Remove unnecessary reg check
- pca955x: Don't invert requested value in pca955x_gpio_set_value()
LED documentation improvements:
- update 00-INDEX file"
* tag 'leds_for_4.15rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: Add driver for PC Engines APU/APU2 LEDs
leds: lp55xx: fix spelling mistake: 'cound' -> 'could'
leds: Convert timers to use timer_setup()
Documentation: leds: Update 00-INDEX file
leds: tca6507: Remove unnecessary reg check
leds: ledtrig-heartbeat: Convert timers to use timer_setup()
leds: Replace flags bit shift with BIT() macros
leds: pca955x: Don't invert requested value in pca955x_gpio_set_value()
leds: ledtrig-activity: Add a system activity LED trigger
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Willy Tarreau <w@1wt.eu>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Instead of using .data directly, convert to from_timer. Since the
trigger_data is allocated separately, the led_cdev must be explicitly
tracked for the callback.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Zhang Bo <bo.zhang@nxp.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linux-leds@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The "activity" trigger was inspired by the heartbeat one, but aims at
providing instant indication of the immediate CPU usage. Under idle
condition, it flashes 10ms every second. At 100% usage, it flashes
90ms every 100ms. The blinking frequency increases from 1 to 10 Hz
until either the load is high enough to saturate one CPU core or 50%
load is reached on a single-core system. Then past this point only the
duty cycle increases from 10 to 90%.
This results in a very visible activity reporting allowing one to
immediately tell whether a machine is under load or not, making it
quite suitable to be used in clusters.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5JLc
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"This time we're removing more than adding:
Removed drivers:
leds-versatile:
- all users of the Versatile LED driver are deleted and replaced
with the very generic leds-syscon
leds-sead3:
- SEAD3 is using the generic leds-syscon & regmap based
register-bit-led driver
LED class drivers improvements:
ledtrig-gpio:
- use threaded IRQ, which both simplifies the code because we can
drop the workqueue indirection, and it enables using the trigger
for GPIOs that work with threaded IRQs themselves
- refresh LED state after GPIO change since the new GPIO may have
a different state than the old one
leds-lp55xx:
- make various arrays static const
leds-pca963x:
- add bindings to invert polarity"
* tag 'leds_for_4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: lp55xx: make various arrays static const
leds: Remove SEAD-3 driver
leds: trigger: gpio: Use threaded IRQ
leds: trigger: gpio: Refresh LED state after GPIO change
leds: Delete obsolete Versatile driver
leds: pca963x: Add bindings to invert polarity
This reverts commit 5ab92a7cb8.
System cannot enter suspend mode because of heartbeat led trigger.
In autosleep_wq, try_to_suspend function will try to enter suspend
mode in specific period. it will get wakeup_count then call pm_notifier
chain callback function and freeze processes.
Heartbeat_pm_notifier is called and it call led_trigger_unregister to
change the trigger of led device to none. It will send uevent message
and the wakeup source count changed. As wakeup_count changed, suspend
will abort.
Fixes: 5ab92a7cb8 ("leds: handle suspend/resume in heartbeat trigger")
Signed-off-by: Zhang Bo <bo.zhang@nxp.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This both simplifies the code because we can drop the workqueue
indirection, and it enables using the trigger for GPIOs that work with
threaded IRQs themselves.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The new GPIO may have a different state than the old one.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Currently there is one CPU led trigger per cpu ('cpu0', 'cpu1', ...)
This patch adds a new trigger, 'cpu', with brightness proportional to
the number of active CPUs.
If multiple brightness levels aren't supported on the LED,
it effectively indicates if there is any CPU active.
This is particularly useful on tiny linux boards with more CPU cores than LED pins.
Signed-off-by: Paulo Costa <me@paulo.costa.nom.br>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
We are going to split <linux/sched/loadavg.h> out of <linux/sched.h>, which
will have to be picked up from a couple of .c files.
Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
LED class heartbeat trigger allowed only for blinking with max_brightness
value. This patch adds more flexibility by exploiting part of LED core
software blink infrastructure.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
There is no need the ledtriger to be called *that* early in the hotplug
process (+ with disabled interrupts). As explained by Jacek Anaszewski [0]
there is no need for it.
Therefore this patch moves it to the ONLINE/PREPARE_DOWN level using the
dynamic registration for the id.
[0] https://lkml.kernel.org/r/578C92BC.2070603@samsung.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: rt@linutronix.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-leds@vger.kernel.org
Link: http://lkml.kernel.org/r/1469028295-14702-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a straightforward conversion. We place this callback last
in the list so that the LED illuminates only after a successful
bring up sequence.
( NOTE: The patch adds a FIXME question about the callback used,
this question should probably be revisited later on.)
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-leds@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.465496902@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The following phenomena was observed: when suspending the
system, sometimes the heartbeat LED was left on, glowing and
wasting power while the rest of the system is asleep, also
disturbing power dissapation measures on the odd suspend
cycle when it's left on.
Clearly this is not how we want the heartbeat trigger to
work: it should turn off and leave the LED off during
system suspend.
This removes the heartbeat trigger when preparing suspend and
restores it during resume. The trigger code will make sure all
LEDs are left in OFF state after removing the trigger, and
will re-enable the trigger on all LEDs after resuming.
Cc: linux-pm@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit adds a new led_cdev flag LED_PANIC_INDICATOR, which
allows to mark a specific LED to be switched to the "panic"
trigger, on a kernel panic.
This is useful to allow the user to assign a regular trigger
to a given LED, and still blink that LED on a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Parameters delay_on and delay_off of led_trigger_blink_oneshot()
are pointers, to enable blink interval adjustment by LED class drivers
of the controllers that implement hardware blinking.
Move ide_blink_delay variable to ledtrig_ide_activity() in order to
prevent the situation when adjustment committed by one LED class
driver influences blink interval of the software fallback blink feature,
that is applied to the drivers that don't implement blink_set op.
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Thomas Gleixner