intel_modeset_gem_init() now only sets up the legacy overlay, so let's
remove the function and call the setup directly during driver load. This
should help us find a better point in the initialisation sequence for it
later.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171110142634.10551-5-chris@chris-wilson.co.uk
This patch adds per engine reset and recovery (TDR) support when GuC is
used to submit workloads to GPU.
In the case of i915 directly submission to ELSP, driver manages hang
detection, recovery and resubmission. With GuC submission these tasks
are shared between driver and GuC. i915 is still responsible for detecting
a hang, and when it does it only requests GuC to reset that Engine. GuC
internally manages acquiring forcewake and idling the engine before
resetting it.
Once the reset is successful, i915 takes over again and handles the
resubmission. The scheduler in i915 knows which requests are pending so
after resetting a engine, pending workloads/requests are resubmitted
again.
v2: s/i915_guc_request_engine_reset/i915_guc_reset_engine/ to match the
non-guc function names.
v3: Removed debug message about engine restarting from which request,
since the new baseline do it regardless of submission mode. (Chris)
v4: Rebase.
v5: Do not pass unnecessary reporting flags to the fw (Jeff);
tasklet_schedule(&execlists->irq_tasklet) handles the resubmit; rebase.
v6: Rename the existing reset engine function and share a similar
interface between guc and non-guc paths (Chris).
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031225309.10888-1-michel.thierry@intel.com
Reviewed-by: Jeff McGee <jeff.mcgee@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Pretty similar to what we have on execlists.
We're reusing most of the GEM code, however, due to GuC quirks we need a
couple of extra bits.
Preemption is implemented as GuC action, and actions can be pretty slow.
Because of that, we're using a mutex to serialize them. Since we're
requesting preemption from the tasklet, the task of creating a workitem
and wrapping it in GuC action is delegated to a worker.
To distinguish that preemption has finished, we're using additional
piece of HWSP, and since we're not getting context switch interrupts,
we're also adding a user interrupt.
The fact that our special preempt context has completed unfortunately
doesn't mean that we're ready to submit new work. We also need to wait
for GuC to finish its own processing.
v2: Don't compile out the wait for GuC, handle workqueue flush on reset,
no need for ordered workqueue, put on a reviewer hat when looking at my own
patches (Chris)
Move struct work around in intel_guc, move user interruput outside of
conditional (Michał)
Keep ring around rather than chase though intel_context
v3: Extract WA for flushing ggtt writes to a helper (Chris)
Keep work_struct in intel_guc rather than engine (Michał)
Use ordered workqueue for inject_preempt worker to avoid GuC quirks.
v4: Drop now unused INTEL_GUC_PREEMPT_OPTION_IMMEDIATE (Daniele)
Drop stray newlines, use container_of for intel_guc in worker,
check for presence of workqueue when flushing it, rather than
enable_guc_submission modparam, reorder preempt postprocessing (Chris)
v5: Make wq NULL after destroying it
v6: Swap struct guc_preempt_work members (Michał)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171026133558.19580-1-michal.winiarski@intel.com
We would also like to make use of execlist_cancel_port_requests and
unwind_incomplete_requests in GuC preemption backend.
Let's rename the functions to use the correct prefixes, so that we can
simply add the declarations in the following patch.
Similar thing for applies for can_preempt, except we're introducing
HAS_LOGICAL_RING_PREEMPTION macro instad, converting other users that
were previously touching device info directly.
v2: s/intel_engine/execlists and pass execlists to unwind (Chris)
v3: use locked version for exporting, drop const qual (Chris)
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171025200020.16636-11-michal.winiarski@intel.com
Defined new struct intel_rc6 to hold RC6 specific state and
intel_ring_pstate to hold ring specific state.
v2: s/intel_ring_pstate/intel_llc_pstate. Removed checks from
autoenable_* functions. (Chris)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-13-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-12-chris@chris-wilson.co.uk
This function gives the status of RC6, whether disabled or if
enabled then which state. intel_enable_rc6 will be used for
enabling RC6 in the next patch.
v2: Rebase.
v3: Rebase.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> #1
Reviewed-by: Ewelina Musial <ewelina.musial@intel.com> #1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-10-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-9-chris@chris-wilson.co.uk
Prepared substructure rps for RPS related state. autoenable_work is
used for RC6 too hence it is defined outside rps structure. As we do
this lot many functions are refactored to use intel_rps *rps to access
rps related members. Hence renamed intel_rps_client pointer variables
to rps_client in various functions.
v2: Rebase.
v3: s/pm/gt_pm (Chris)
Refactored access to rps structure by declaring struct intel_rps * in
many functions.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com> #1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-9-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-8-chris@chris-wilson.co.uk
Use a priority stored in the context as the initial value when
submitting a request. This allows us to change the default priority on a
per-context basis, allowing different contexts to be favoured with GPU
time at the expense of lower importance work. The user can adjust the
context's priority via I915_CONTEXT_PARAM_PRIORITY, with more positive
values being higher priority (they will be serviced earlier, after their
dependencies have been resolved). Any prerequisite work for an execbuf
will have its priority raised to match the new request as required.
Normal users can specify any value in the range of -1023 to 0 [default],
i.e. they can reduce the priority of their workloads (and temporarily
boost it back to normal if so desired).
Privileged users can specify any value in the range of -1023 to 1023,
[default is 0], i.e. they can raise their priority above all overs and
so potentially starve the system.
Note that the existing schedulers are not fair, nor load balancing, the
execution is strictly by priority on a first-come, first-served basis,
and the driver may choose to boost some requests above the range
available to users.
This priority was originally based around nice(2), but evolved to allow
clients to adjust their priority within a small range, and allow for a
privileged high priority range.
For example, this can be used to implement EGL_IMG_context_priority
https://www.khronos.org/registry/egl/extensions/IMG/EGL_IMG_context_priority.txt
EGL_CONTEXT_PRIORITY_LEVEL_IMG determines the priority level of
the context to be created. This attribute is a hint, as an
implementation may not support multiple contexts at some
priority levels and system policy may limit access to high
priority contexts to appropriate system privilege level. The
default value for EGL_CONTEXT_PRIORITY_LEVEL_IMG is
EGL_CONTEXT_PRIORITY_MEDIUM_IMG."
so we can map
PRIORITY_HIGH -> 1023 [privileged, will failback to 0]
PRIORITY_MED -> 0 [default]
PRIORITY_LOW -> -1023
They also map onto the priorities used by VkQueue (and a VkQueue is
essentially a timeline, our i915_gem_context under full-ppgtt).
v2: s/CAP_SYS_ADMIN/CAP_SYS_NICE/
v3: Report min/max user priorities as defines in the uapi, and rebase
internal priorities on the exposed values.
Testcase: igt/gem_exec_schedule
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003203453.15692-9-chris@chris-wilson.co.uk
When we write to ELSP, it triggers a context preemption at the earliest
arbitration point (3DPRIMITIVE, some PIPECONTROLs, a few other
operations and the explicit MI_ARB_CHECK). If this is to the same
context, it triggers a LITE_RESTORE where the RING_TAIL is merely
updated (used currently to chain requests from the same context
together, avoiding bubbles). However, if it is to a different context, a
full context-switch is performed and it will start to execute the new
context saving the image of the old for later execution.
Previously we avoided preemption by only submitting a new context when
the old was idle. But now we wish embrace it, and if the new request has
a higher priority than the currently executing request, we write to the
ELSP regardless, thus triggering preemption, but we tell the GPU to
switch to our special preemption context (not the target). In the
context-switch interrupt handler, we know that the previous contexts
have finished execution and so can unwind all the incomplete requests
and compute the new highest priority request to execute.
It would be feasible to avoid the switch-to-idle intermediate by
programming the ELSP with the target context. The difficulty is in
tracking which request that should be whilst maintaining the dependency
change, the error comes in with coalesced requests. As we only track the
most recent request and its priority, we may run into the issue of being
tricked in preempting a high priority request that was followed by a
low priority request from the same context (e.g. for PI); worse still
that earlier request may be our own dependency and the order then broken
by preemption. By injecting the switch-to-idle and then recomputing the
priority queue, we avoid the issue with tracking in-flight coalesced
requests. Having tried the preempt-to-busy approach, and failed to find
a way around the coalesced priority issue, Michal's original proposal to
inject an idle context (based on handling GuC preemption) succeeds.
The current heuristic for deciding when to preempt are only if the new
request is of higher priority, and has the privileged priority of
greater than 0. Note that the scheduler remains unfair!
v2: Disable for gen8 (bdw/bsw) as we need additional w/a for GPGPU.
Since, the feature is now conditional and not always available when we
have a scheduler, make it known via the HAS_SCHEDULER GETPARAM (now a
capability mask).
v3: Stylistic tweaks.
v4: Appease Joonas with a snippet of kerneldoc, only to fuel to fire of
the preempt vs preempting debate.
Suggested-by: Michal Winiarski <michal.winiarski@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003203453.15692-8-chris@chris-wilson.co.uk
In the next few patches, we wish to enable different features for the
scheduler, some which may subtlety change ABI (e.g. allow requests to be
reordered under different circumstances). So we need to make sure
userspace is cognizant of the changes (if they care), by which we employ
the usual method of a GETPARAM. We already have an
I915_PARAM_HAS_SCHEDULER (which notes the existing ability to reorder
requests to avoid bubbles), and now we wish to extend that to be a
bitmask to describe the different capabilities implemented.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003203453.15692-7-chris@chris-wilson.co.uk
This patch adds new function intel_uc_init_mmio which will initialize
MMIO access related variables prior to uc load/init.
v2: Removed unnecessary export of guc_send_init_regs. Created
intel_uc_init_mmio that currently wraps guc_init_send_regs. (Michal)
v3 (Michal): add kerneldoc (Joonas)
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171004153327.32608-4-michal.wajdeczko@intel.com
Atm, on GEN9 big core platforms before saving the hibernation image we
uninitialize the display, disabling power wells manually, while before
restoring the image we keep things powered (letting HW/DMC power down
things as needed). The state mismatch will trigger the following error:
DC state mismatch (0x0 -> 0x2)
While the restore handler knows how to initialize the display from an
unknown state (due to a different loader kernel or not having i915
loaded in the loader kernel) we should still use the same state for
consistency before image saving and restoring. Do this by uniniting the
display before restoring the image too.
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?id=133376
Reported-and-tested-by: Wang Wendy <wendy.wang@intel.com>
Reported-and-tested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Wang Wendy <wendy.wang@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170816144607.9935-1-imre.deak@intel.com
If we store the platform as a bitmask, and convert the
IS_PLATFORM macro to use it, we allow the compiler to
merge the IS_PLATFORM(a) || IS_PLATFORM(b) || ... checks
into a single conditional.
As a secondary benefit this saves almost 1k of text:
text data bss dec hex filename
-1460254 60014 3656 1523924 1740d4 drivers/gpu/drm/i915/i915.ko
+1459260 60026 3656 1522942 173cfe drivers/gpu/drm/i915/i915.ko
v2: Removed the infamous -1.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170927164138.15474-1-tvrtko.ursulin@linux.intel.com
Our global struct with params is named exactly the same way
as new preferred name for the drm_i915_private function parameter.
To avoid such name reuse lets use different name for the global.
v5: pure rename
v6: fix
Credits-to: Coccinelle
@@
identifier n;
@@
(
- i915.n
+ i915_modparams.n
)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170919193846.38060-1-michal.wajdeczko@intel.com
This patch adds IPC support. This patch also enables IPC in all supported
platforms based on has_ipc flag.
IPC (Isochronous Priority Control) is the hardware feature, which
dynamically controls the memory read priority of Display.
When IPC is enabled, plane read requests are sent at high priority until
filling above the transition watermark, then the requests are sent at
lower priority until dropping below the level 0 watermark.
The lower priority requests allow other memory clients to have better
memory access. When IPC is disabled, all plane read requests are sent at
high priority.
Changes since V1:
- Remove commandline parameter to disable ipc
- Address Paulo's comments
Changes since V2:
- Address review comments
- Set ipc_enabled flag
Changes since V3:
- move ipc_enabled flag assignment inside intel_ipc_enable function
Changes since V4:
- Re-enable IPC after suspend/resume
Changes since V5:
- Enable IPC for all gen >=9 except SKL
Changes since V6:
- fix commit msg
- after resume program IPC based on SW state.
Changes since V7:
- Modify IPC support check based on HAS_IPC macro (suggested by Chris)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817134529.2839-8-mahesh1.kumar@intel.com
Ville Syrjälä spotted that PGETBL_CTL was losing its enable bit upon a
reset. That was causing the display to show garbage on his 945gm. On my
i915gm the effect was far more severe; re-enabling the display following
the reset without PGETBL_CTL being enabled lead to an immediate hard
hang.
We do have a routine to re-enable PGETBL_CTL which is applicable to
gen2-4, although on gen4 it is documented that a graphics reset doesn't
alter the register (no such wording is given for gen3) and should be safe
to call to punch back in the enable bit. However, that leaves the question
of whether we need to completely re-initialise the register and the
rest of the GSM. For g33/pnv/gen4+, where we do have a configurable
page table, its contents do seem to be kept, and so we should be able to
recover without having to reinitialise the GTT from scratch (as prior to
g33, that register is configured by the BIOS and we leave alone except
for the enable bit).
This appears to have been broken by commit 5fbd0418ee ("drm/i915:
Re-enable GGTT earlier during resume on pre-gen6 platforms"), which
moved the intel_enable_gtt() from i915_gem_init_hw() (also used by
reset) to add it earlier during hw init and resume, missing the reset
path.
v2: Find the culprit, rearrange ggtt_enable to be before gem_init_hw to
match init/resume
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 5fbd0418ee ("drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101852
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170906111405.27110-1-chris@chris-wilson.co.uk
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Coffee Lake CPU on Kaby Lake PCH is possible.
It does exist, and it does work.
The only missed case was this warning here noticed
by Wendy who could get one system with this configuration
and reported the issue for us:
Hardware Configuration
Board ID KBL S DDR4 UDIMM EV CRB
Processor Intel® Processor code named Coffee Lake S, (6+2), 6 cores 12 threads, GT2, A0 (Internal) (QNJ4)
[ 3.220585] WARNING: CPU: 10 PID: 206 at drivers/gpu/drm/i915/i915_drv.c:340 i915_driver_load+0x1210/0x1660 [i915]
[ 3.221312] Modules linked in: hid_generic usbhid i915 i2c_algo_bit drm_kms_helper e1000e syscopyarea sysfillrect sysimgblt nvme fb_sys_fops ptp ahci i2c_hid drm pps_core nvme_core libahci wmi hid video
[ 3.222050] CPU: 10 PID: 206 Comm: systemd-udevd Not tainted 4.13.0-rc5-intel-next+ #1
[ 3.222706] Hardware name: Intel Corporation Kabylake Client platform/KBL S DDR4 UDIMM EV CRB, BIOS KBLSE2R1.R00.X089.P00.1705051000 05/05/2017
Cc: Wendy Wang <wendy.wang@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170821235056.9015-1-rodrigo.vivi@intel.com
This commit adds support for waiting on or signaling DRM syncobjs as
part of execbuf. It does so by hijacking the currently unused cliprects
pointer to instead point to an array of i915_gem_exec_fence structs
which containe a DRM syncobj and a flags parameter which specifies
whether to wait on it or to signal it. This implementation
theoretically allows for both flags to be set in which case it waits on
the dma_fence that was in the syncobj and then immediately replaces it
with the dma_fence from the current execbuf.
v2:
- Rebase on new syncobj API
v3:
- Pull everything out into helpers
- Do all allocation in gem_execbuffer2
- Pack the flags in the bottom 2 bits of the drm_syncobj*
v4:
- Prevent a potential race on syncobj->fence
Testcase: igt/gem_exec_fence/syncobj*
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1499289202-25441-1-git-send-email-jason.ekstrand@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170815145733.4562-1-chris@chris-wilson.co.uk
Ben Widawsky/Daniel Stone need the extended modifier support from
drm-misc to be able to merge CCS support for i915.ko
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change.
KBP was based on SPT and spec wasn't clear about the full name.
There was the initial point of the "Point" confusion.
Later the split with Coffee Lake and Cannon Lake both using CNP
and also some uncertainty from the specs we had at that time
made us to propagated the mistake along.
So, let's fix this now and avoid propagating these wrong
"points".
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170731185220.758-1-rodrigo.vivi@intel.com
The motivation behind this new interface is expose at runtime the
creation of new OA configs which can be used as part of the i915 perf
open interface. This will enable the kernel to learn new configs which
may be experimental, or otherwise not part of the core set currently
available through the i915 perf interface.
v2: Drop DRM_ERROR for userspace errors (Matthew)
Add padding to userspace structure (Matthew)
s/guid/uuid/ (Matthew)
v3: Use u32 instead of int to iterate through registers (Matthew)
v4: Lock access to dynamic config list (Lionel)
v5: by Matthew:
Fix uninitialized error values
Fix incorrect unwiding when opening perf stream
Use kmalloc_array() to store register
Use uuid_is_valid() to valid config uuids
Declare ioctls as write only
Check padding members are set to 0
by Lionel:
Return ENOENT rather than EINVAL when trying to remove non
existing config
v6: by Chris:
Use ref counts for OA configs
Store UUID in drm_i915_perf_oa_config rather then using pointer
Shuffle fields of drm_i915_perf_oa_config to avoid padding
v7: by Chris
Rename uapi pointers fields to end with '_ptr'
v8: by Andrzej, Marek, Sebastian
Update register whitelisting
by Lionel
Add more register names for documentation
Allow configuration programming in non-paranoid mode
Add support for value filter for a couple of registers already
programmed in other part of the kernel
v9: Documentation fix (Lionel)
Allow writing WAIT_FOR_RC6_EXIT only on Gen8+ (Andrzej)
v10: Perform read access_ok() on register pointers (Lionel)
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Reviewed-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170803165812.2373-2-lionel.g.landwerlin@intel.com
During our selftests, we try reseting the GPU tens of thousands of
times, flooding the dmesg with our reset spam drowning out any potential
warnings. Add an option to i915_reset()/i915_reset_engine() to specify a
quiet reset for selftesting.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-19-chris@chris-wilson.co.uk
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Although a banned context will be told to -EIO off if they try to submit
more requests, we have a discrepancy between whole device resets and
per-engine resets where we report the GPU reset but not the engine
resets. This leaves a bit of mystery as to why the context was banned,
and also reduces awareness overall of when a GPU (engine) reset occurs
with its possible side-effects.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-13-chris@chris-wilson.co.uk
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We rely on disabling the execlists (by stopping the tasklet) to prevent
new requests from submitting to the engine ELSP before we are ready.
However, we re-enable the engine before we call init_hw which gives
userspace the opportunity to subit a new request which is then
overwritten by init_hw -- but not before the HW may have started
executing. The subsequent out-of-order CSB is detected by our sanity
checks in intel_lrc_irq_handler().
Fixes: a1ef70e144 ("drm/i915: Add support for per engine reset recovery")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-3-chris@chris-wilson.co.uk
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We try to fixup the context image after the reset to ensure that there
are no more pending writes from the hw that may conflict and to fixup
any that were in flight.
Fixes: a1ef70e144 ("drm/i915: Add support for per engine reset recovery")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170721123238.16428-2-chris@chris-wilson.co.uk
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Resync with upstream to avoid git getting too badly confused. Also, we
have a conflict with the drm_vblank_cleanup removal, which cannot be
resolved by simply taking our side. Bake that in properly.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I need this to be able to apply the deferred fbdev setup patches, I
need the relevant prep work that landed through the drm-intel tree.
Also squash in conflict fixup from Laurent Pinchart.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This gets rid of all the interactions between the legacy flip code and
the modeset code. Yay!
This highlights an ommission in the atomic paths, where we fail to
apply a boost to the pending rendering when we miss the target vblank.
But the existing code is still dead and can be removed.
v2: Note that the boosting doesn't work in atomic (Chris).
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170720175754.30751-7-daniel.vetter@ffwll.ch
We first need to make sure no one else can get at us anymore,
before we can proceed to tear down all the datastructures.
Just a small step towards eventually the perfect unload code ...
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170714224656.6431-3-daniel.vetter@ffwll.ch
First thing we need to do is unregister the fbdev instance, but we
can't just go ahead and kfree it. That must wait until the hotplug and
polling work are stopped, since they can race with the with the
teardown. That means we need to split up the fbdev teardown into the
unregister part and the cleanup part.
I originally suspected that this was broken in one of the unload
shuffles, but on closer inspection the oldest sequence I've dug out
also gets this wrong. Just not quite so badly.
I've run drv_module_reload a few hundred times and it's rock solid
compared to insta-death beforehand. This bug seems to have been
uncovered by
commit 88be58be88
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 6 15:00:19 2017 +0200
drm/i915/fbdev: Always forward hotplug events
But the effect of that seems to only be to increase the race window
enough to make it blow up easier. I'm not exactly clear on what's
going on there ...
v2: Fix whitespace and use fetch_and_zero (Chris).
Testcase: igt/drv_module_reload
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101791
Cc: martin.peres@free.fr
Cc: chris@chris-wilson.co.uk
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170714224656.6431-2-daniel.vetter@ffwll.ch
Workers on the i915->wq may rearm themselves so for completeness we need
to replace our flush_workqueue() with a call to drain_workqueue() before
unloading the device.
v2: Reinforce the drain_workqueue with an preceding rcu_barrier() as a
few of the tasks that need to be drained may first be armed by RCU.
References: https://bugs.freedesktop.org/show_bug.cgi?id=101627
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170718134124.14832-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
In a IGD passthrough environment, the real ISA bridge may doesn't exist.
then pch_id couldn't be correctly gotten from ISA bridge, but pch_id is
used to identify LPT_H and LPT_LP. Currently i915 treat all LPT pch as
LPT_H,then errors occur when i915 runs on LPT_LP machines with igd
passthrough.
This patch set pch_id for HSW/BDW according to IGD type and isn't fully
correct. But it solves such issue on HSW/BDW ult/ulx machines.
QA CI system is blocked by this issue for a long time, it's better that
we could merge it to unblock QA CI system.
We know the root cause is in device model of virtual passthrough, and
will resolve it in the future with several parts cooperation in kernel,
qemu and xen.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99938
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1497496305-5364-1-git-send-email-xiong.y.zhang@intel.com
We have pretty clear evidence that MSIs are getting lost on g4x and
somehow the interrupt logic doesn't seem to recover from that state
even if we try hard to clear the IIR.
Disabling IER around the normal IIR clearing in the irq handler isn't
sufficient to avoid this, so the problem really seems to be further
up the interrupt chain. This should guarantee that there's always
an edge if any IIR bits are set after the interrupt handler is done,
which should normally guarantee that the CPU interrupt is generated.
That approach seems to work perfectly on VLV/CHV, but apparently
not on g4x.
MSI is documented to be broken on 965gm at least. The chipset spec
says MSI is defeatured because interrupts can be delayed or lost,
which fits well with what we're seeing on g4x. Previously we've
already disabled GMBUS interrupts on g4x because somehow GMBUS
manages to raise legacy interrupts even when MSI is enabled.
Since there's such widespread MSI breakahge all over in the pre-gen5
land let's just give up on MSI on these platforms.
Seqno reporting might be negatively affected by this since the legcy
interrupts aren't guaranteed to be ordered with the seqno writes,
whereas MSI interrupts may be? But an occasioanlly missed seqno
seems like a small price to pay for generally working interrupts.
Cc: stable@vger.kernel.org
Cc: Diego Viola <diego.viola@gmail.com>
Tested-by: Diego Viola <diego.viola@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101261
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170626203051.28480-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to do a modeset from within a reset is fraught with danger. We
can fall into a cyclic deadlock where the modeset is waiting on a
previous modeset that is waiting on a request, and since the GPU hung
that request completion is waiting on the reset. As modesetting doesn't
allow its locks to be broken and restarted, or for its *own* reset
mechanism to take over the display, we have to do something very
evil instead. If we detect that we are stuck waiting to prepare the
display reset (by using a very simple timeout), resort to cancelling all
in-flight requests and throwing the user data into /dev/null, which is
marginally better than the driver locking up and keeping that data to
itself.
This is not a fix; this is just a workaround that unbreaks machines
until we can resolve the deadlock in a way that doesn't lose data!
v2: Move the retirement from set-wegded to the i915_reset() error path,
after which we no longer any delayed worker cleanup for
i915_handle_error()
v3: C abuse for syntactic sugar
v4: Cover all waits with the timeout to catch more driver breakage
References: https://bugs.freedesktop.org/show_bug.cgi?id=99093
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170622105625.16952-1-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Make the code less confusiong by always using the top 9 bits of the
LPC bridge device ID to detect the PCH type. We need to add a bit of
new code for WPT, and we need to adjust the KBP ID as well. All the
other pre-CNP IDs are fine as is.
The virtualization cases I think are fine. These P2X and P3X IDs
actually just look like the old PIIX4 and PIIX3 IDs to me. Not sure
why they're not called PIIX3/4 though. The qemu one has a comment
saying the full ID is 0x2918 which is fine with 9 bits.
v2: Keep the CNP ID as 0xa300 (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170621174944.23306-1-ville.syrjala@linux.intel.com
Write the '!(SNB||IVB)' checks in the CPT/PPT detections
as '!SNB && !IVB' to make it less messy looking, and clear out
some useless parens the from the virtualization PCH detection case.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620130310.13245-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Driver maintains count of how many times a given engine is reset, useful to
capture this in error state also. It gives an idea of how engine is coping
up with the workloads it is executing before this error state.
A follow-up patch will provide this information in debugfs.
v2: s/engine_reset/reset_engine/ (Chris)
Define count as unsigned int (Tvrtko)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-7-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-7-chris@chris-wilson.co.uk
This change implements support for per-engine reset as an initial, less
intrusive hang recovery option to be attempted before falling back to the
legacy full GPU reset recovery mode if necessary. This is only supported
from Gen8 onwards.
Hangchecker determines which engines are hung and invokes error handler to
recover from it. Error handler schedules recovery for each of those engines
that are hung. The recovery procedure is as follows,
- identifies the request that caused the hang and it is dropped
- force engine to idle: this is done by issuing a reset request
- reset the engine
- re-init the engine to resume submissions.
If engine reset fails then we fall back to heavy weight full gpu reset
which resets all engines and reinitiazes complete state of HW and SW.
v2: Rebase.
v3: s/*engine_reset*/*reset_engine*/; freeze engine and irqs before
calling i915_gem_reset_engine (Chris).
v4: Rebase, modify i915_gem_reset_prepare to use a ring mask and
reuse the function for reset_engine.
v5: intel_reset_engine_start/cancel instead of request/unrequest_reset.
v6: Clean up reset_engine function to not require mutex, i.e. no need to call
revoke/restore_fences and _retire_requests (Chris).
v7: Remove leftovers from v5, i.e. no need to disable irq, hold
forcewake or wakeup the handoff bit (Chris).
v8: engine_retire_requests should be (and it was) static; explain that
we have to re-init the engine after reset, which is why the init_hw call
is needed; check reset-in-progress flag (Chris).
v9: Rebase, include code to pass the active request to gem_reset_engine
(as it is already done in full reset). Remove unnecessary
intel_reset_engine_start/cancel, these are executed as part of the
reset.
v10: Rebase, use the right I915_RESET_ENGINE flag.
v11: Fixup to call reset_finish_engine even on error.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-6-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-6-chris@chris-wilson.co.uk
This is a preparatory patch which modifies error handler to do per engine
hang recovery. The actual patch which implements this sequence follows
later in the series. The aim is to prepare existing recovery function to
adapt to this new function where applicable (which fails at this point
because core implementation is lacking) and continue recovery using legacy
full gpu reset.
A helper function is also added to query the availability of engine
reset. A subsequent patch will add the capability to query which type
of reset is present (engine -> full -> no-reset) via the get-param
ioctl.
It has been decided that the error events that are used to notify user of
reset will only be sent in case if full chip reset. In case of just
single (or multiple) engine resets, userspace won't be notified by these
events.
Note that this implementation of engine reset is for i915 directly
submitting to the ELSP, where the driver manages the hang detection,
recovery and resubmission. With GuC submission these tasks are shared
between driver and firmware; i915 will still responsible for detecting a
hang, and when it does it will have to request GuC to reset that Engine and
remind the firmware about the outstanding submissions. This will be
added in different patch.
v2: rebase, advertise engine reset availability in platform definition,
add note about GuC submission.
v3: s/*engine_reset*/*reset_engine*/. (Chris)
Handle reset as 2 level resets, by first going to engine only and fall
backing to full/chip reset as needed, i.e. reset_engine will need the
struct_mutex.
v4: Pass the engine mask to i915_reset. (Chris)
v5: Rebase, update selftests.
v6: Rebase, prepare for mutex-less reset engine.
v7: Pass reset_engine mask as a function parameter, and iterate over the
engine mask for reset_engine. (Chris)
v8: Use i915.reset >=2 in has_reset_engine; remove redundant reset
logging; add a reset-engine-in-progress flag to prevent concurrent
resets, and avoid dual purposing of reset-backoff. (Chris)
v9: Support reset of different engines in parallel (Chris)
v10: Handle reset-engine flag locking better (Chris)
v11: Squash in reporting of per-engine-reset availability.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Ian Lister <ian.lister@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170615201828.23144-4-michel.thierry@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620095751.13127-5-chris@chris-wilson.co.uk
If we move the actual cleanup of the context to a worker, we can allow
the final free to be called from any context and avoid undue latency in
the caller.
v2: Negotiate handling the delayed contexts free by flushing the
workqueue before calling i915_gem_context_fini() and performing the final
free of the kernel context directly
v3: Flush deferred frees before new context allocations
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170620110547.15947-2-chris@chris-wilson.co.uk
Although we use 9 bits of Device ID for identifying PCH, only 8 bits are
stored in dev_priv->pch_id. This makes HAS_PCH_CNP_LP() and
HAS_PCH_SPT_LP() incorrect. Fix this by storing all the 9 bits for the
platforms with LP PCH.
v2: Drop PCH_LPT_LP change (Imre)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Fixes: commit ec7e0bb35f ("drm/i915/cnp: Add PCI ID for Cannonpoint LP PCH")
Reported-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497641774-29104-1-git-send-email-dhinakaran.pandiyan@intel.com
Currently, the last object in the execlist is the always the batch.
However, when building the batch buffer we often know the batch object
first and if we can use the first slot in the execlist we can emit
relocation instructions relative to it immediately and avoid a separate
pass to adjust the relocations to point to the last execlist slot.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Chris Wilson