Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode
("RGMII-*ID") settings, but used the hardware defaults, augmented by
explicit configuration of individual skew values using the "*-skew-ps"
DT properties. The lack of PHY mode support was compensated by the
EtherAVB MAC driver, which configures TX and/or RX internal delay
itself, based on the PHY mode.
However, now the KSZ9031 driver has gained PHY mode support, delays may
be configured twice, causing regressions. E.g. on the Renesas
Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca.
400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp.
As internal delay configuration supported by the KSZ9031 PHY is too
limited for some use cases, the ability to configure MAC internal delay
is deemed useful and necessary. Hence a proper fix would involve
splitting internal delay configuration in two parts, one for the PHY,
and one for the MAC. However, this would require adding new DT
properties, thus breaking DTB backwards-compatibility.
Hence fix the regression in a backwards-compatibility way, by letting
the EtherAVB driver mask the PHY mode when it has inserted a delay, to
avoid the PHY driver adding a second delay. This also fixes messages
like:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii"
as the PHY no longer sees the original RGMII-*ID mode.
Solving the issue by splitting configuration in two parts can be handled
in future patches, and would require retaining a backwards-compatibility
mode anyway.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove fdb from nh_list before the rcu grace period
- protect fdb->vdev with rcu
- hold spin lock before destroying fdb
Fixes: c7cdbe2efc ("vxlan: support for nexthop notifiers")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NDA_NH_ID represents a remote ip or a group of remote ips.
It allows use of nexthop groups in lieu of a remote ip or a
list of remote ips supported by the fdb api.
Current code ignores the other remote ip attrs when NDA_NH_ID is
specified. In the spirit of strict checking, This commit adds a
check to explicitly return an error on incorrect usage.
Fixes: 1274e1cc42 ("vxlan: ecmp support for mac fdb entries")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-28
This series contains updates to the ice driver only.
Anirudh (Ani) adds a poll for reset completion before proceeding with
driver initialization when the DDP package fails to load and the firmware
issues a core reset.
Jake cleans up unnecessary code, since ice_set_dflt_vsi_ctx() performs a
memset to clear the info from the context structures. Fixed a potential
double free during probe unrolling after a failure. Also fixed a
potential NULL pointer dereference upon register_netdev() failure.
Tony makes two functions static which are not called outside of their
file.
Brett refactors the ice_ena_vf_mappings(), which was doing the VF's MSIx
and queue mapping in one function which was hard to digest. So create a
new function to handle the enabling MSIx mappings and another function
to handle the enabling of queue mappings. Simplify the code flow in
ice_sriov_configure(). Created a helper function for clearing
VPGEN_VFRTRIG register, as this needs to be done on reset to notify the
VF that we are done resetting it. Fixed the initialization/creation and
reset flows, which was unnecessarily complicated, so separate the two
flows into their own functions. Renamed VF initialization functions to
make it more clear what they do and why. Added functionality to set the
VF trust mode bit on reset. Added helper functions to rebuild the VLAN
and MAC configurations when resetting a VF. Refactored how the VF reset
is handled to prevent VF reset timeouts.
Paul cleaned up code not needed during a CORER/GLOBR reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify handling the power management callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functionality for quiescing the chip is spread across different
functions currently. Move it to rtl8169_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move calls that are needed before and after calling rtl8169_hw_reset()
into this function. This requires to move the function in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In places where the indexes have to be reset, we call
rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We go to runtime-suspend few secs after cable removal. As cable is
removed "physical link up" is the only meaningful WoL source.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change driver private data type to struct rtl8169_private * to avoid
some overhead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third set of patches for v5.8. Final new features before the merge
window (most likely) opens, noteworthy here is adding WPA3 support to
old drivers rt2800, b43 and b43_legacy.
Major changes:
ath10k
* SDIO and SNOC busses are not experimental anymore
ath9k
* allow receive of broadcast Action frames
ath9k_htc
* allow receive of broadcast Action frames
rt2800
* enable WPA3 support out of box
b43
* enable WPA3 support
b43_legacy
* enable WPA3 support
mwifiex
* advertise max number of clients to user space
mt76
* mt7663: add remain-on-channel support
* mt7915: add spatial reuse support
* add support for mt7611n hardware
iwlwifi
* add ACPI DSM support
* support enabling 5.2GHz bands in Indonesia via ACPI
* bump FW API version to 56
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJe0nFMAAoJEG4XJFUm622bf04H/1IqM/9Wpt6qMSa+adBz5ij7
yNwWCD2nXAgyirafRIot6uoOY7ePfutwwUXD5IatwPFIEQVZP/uoRDqBPqsbz85J
w5Izvpt15eG5uSDuy5rLUFucOz3XJZQkOGWRo/GKGSLjm2uPGGXAVul+fWX+i05J
xfH1GvLys//An/X6AIx6kWqyJYqUfmxXj7pLkiOYFlt8JNS49gDaA1Emvv7/xv+Q
hyBswKjNrEeT5K4dqYjQ/hp9/ukX8JQtpVBRF7rth5T8gxzJQmOKiP86L8YH5SyI
r3U3ok1aUIuG6xhsTV/cWkqQeD6YsO9M1dTO1WQQLQyZgwl/esbjw/4BVNMGgVk=
=9pX4
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
Third set of patches for v5.8. Final new features before the merge
window (most likely) opens, noteworthy here is adding WPA3 support to
old drivers rt2800, b43 and b43_legacy.
Major changes:
ath10k
* SDIO and SNOC busses are not experimental anymore
ath9k
* allow receive of broadcast Action frames
ath9k_htc
* allow receive of broadcast Action frames
rt2800
* enable WPA3 support out of box
b43
* enable WPA3 support
b43_legacy
* enable WPA3 support
mwifiex
* advertise max number of clients to user space
mt76
* mt7663: add remain-on-channel support
* mt7915: add spatial reuse support
* add support for mt7611n hardware
iwlwifi
* add ACPI DSM support
* support enabling 5.2GHz bands in Indonesia via ACPI
* bump FW API version to 56
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The dynamic configuration interface for the General Params and the L2
Lookup Params tables was copy-pasted between E/T devices and P/Q/R/S
devices. Nonetheless, these interfaces are bitwise different.
The driver is using dynamic reconfiguration of the General Parameters
table for the port mirroring feature, which was therefore broken on
P/Q/R/S.
Note that this patch can't be backported easily very far to stable trees
(since it conflicts with some other development done since the
introduction of the driver). So the Fixes: tag is purely informational.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer compilers complain with W=1 builds that there are non-static
functions defined in sja1105_static_config.c that don't have a
prototype, because their prototype is defined in sja1105.h which this
translation unit does not include.
I don't entirely understand what is the point of these warnings, since
in principle there's nothing wrong with that. But let's move the
prototypes to a header file that _is_ included by
sja1105_static_config.c, since that will make these warnings go away.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7R3wcACgkQSD+KveBX
+j6/ZQf/QD39naPeImfLjemkRK9L+TKbS4nU6wpUwf1jC33Wdm4HhkhsWEnR6C4l
OwU/Pae3I9EtKP4gRE0W1o8h7zC9h4hY7+IKZOdyQ32iUY55PX/H25oqAiCj1NCM
xzWpXOTwK/vkqmkCedAd+YpNdYlbOhfycr+KVPSsvFdaPqjzfNO1PJcLsUbAbzrX
A+8pYdhUYTtx1N3YHJL5abLN6WzMAKxgwlm9GG8YCXACTJT6CBWWHGebVsC5TDUk
Lj5hJj38mI8/3dcu6vWP0kLGVfRZo0HS/gpPGxbKQFpP+1uBYaRENAQONxkY++6S
GDPix7ccvN+yNMlON893PC/Cogw3Yg==
=WaCJ
-----END PGP SIGNATURE-----
Merge tag 'mlx5-cleanup-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-cleanup-2020-05-29
Accumulated cleanup patches and sparse warning fixes for mlx5 driver.
1) sync with mlx5-next branch
2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested
by Jakub Kicinski and David Ahern, and use it in mlx5
3) Jesper Fixes xdp data_meta setup in mlx5
4) Many sparse and build warnings cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_VLAN_CTAG_FILTER is not set in netdev->hw_feature for
the HNS3 driver, so the handler of NETIF_F_HW_VLAN_CTAG_FILTER
in hns3_nic_set_features() won't be called, remove it.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a redundant blank line in hclgevf_cmd_set_promisc_mode(),
and fix a reverse xmas tree coding style issue in
hclgevf_set_rss_tc_mode().
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hclgevf_dev stands for VF device, its field num_tqps
indicates the number of VF's task queue pairs, so the comment
is incorrect, replace 'PF' with 'VF'.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro hclgevf_ring_to_dma_dir and hclgevf_is_csq defined in
hclgevf_cmd.c, but not used, so remove them.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro hclge_is_csq defined in hcgle_cmd.c has not been used,
so remove it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %d to print int variable 'ret' in hclge_mac_mdio_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ath10k/qmi.h header file contains a declaration for the function
ath10k_qmi_register_service_notifier(). This function doesn't exist.
Remove the declaration.
This patch is a no-op and was just found by code inspection.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200528122105.1.I31937dce728b441fd72cbe23447bc4710fd56ddb@changeid
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-2-jouni@codeaurora.org
Advertise support for multicast frame registration and update the RX
filter based on the recently added FIF_MCAST_ACTION to allow broadcast
Action frames to be received. This is needed for Device Provisioning
Protocol (DPP) use cases that use broadcast Public Action frames.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426084733.7889-1-jouni@codeaurora.org
Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c:988:29:
error: symbol 'mlx5e_dcbnl_ops' was not declared. Should it be static?
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix some trivial warnings of the type:
warning: incorrect type in initializer (different base types)
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
tls handle and rcd_sn are actually big endian and not in host format.
Fix that.
Fix the following sparse warnings:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:177:21:
warning: cast to restricted __be64
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:178:52:
warning: incorrect type in argument 2 (different base types)
expected unsigned int [usertype] handle
got restricted __be32 [usertype] handle
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1949:15:
warning: memset with byte count of 271720
mlx5_cmd_stats array is too big to be held inline in mlx5_cmd.
Allocate it separately.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
dr_ste_crc32_calc() calculates crc32 and should return it in HW format.
It is being used to calculate a u32 index, hence we force the return value
of u32 to avoid the sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:115:16:
warning: incorrect type in return expression (different base types)
expected unsigned int
got restricted __be32 [usertype]
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
raw_ip actual type is __be32 and not u32.
Fix that and get rid of the warning.
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:906:31:
warning: cast to restricted __be32
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
HW spec objects should receive a void ptr to work on, the MLX5_SET/GET
macro will know how to handle it.
No need to provide explicit or wrong pointer type in this case.
warning: incorrect type in argument 1 (different base types)
expected unsigned long long const [usertype] *sw_action
got restricted __be64 [usertype] *[assigned] sw_action
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Make use of generic API mpls_entry_encode() to build mpls label and get
rid of local function.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Moving the mlx5_ifc_query_qp_out_bits structure on the stack was a bit
excessive and now causes the compiler to complain on 32-bit architectures:
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field':
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:274:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Revert the previous patch partially to use dynamically allocation as
the code did before. Unfortunately there is no good error handling
in case the allocation fails.
Fixes: 57a6c5e992 ("net/mlx5: Replace hand written QP context struct with automatic getters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:6: warning:
variable 'err' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
if (IS_ERR(d->pkt_reformat)) {
^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3718:6: note:
uninitialized use occurs here
if (err)
^~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:2: note: remove the
'if' if its condition is always true
if (IS_ERR(d->pkt_reformat)) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3670:9: note: initialize
the variable 'err' to silence this warning
int err;
^
= 0
1 warning generated.
It is not wrong, err is only ever initialized in if statements but this
one is not in one. Initialize err to 0 to fix this.
Fixes: 14e6b038af ("net/mlx5e: Add support for hw decapsulation of MPLS over UDP")
Link: https://github.com/ClangBuiltLinux/linux/issues/1037
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The helper function xdp_set_data_meta_invalid() must be called after
setting xdp->data as it depends on it.
The bug was introduced in the cited patch below, and cause the kernel
to crash when using BPF helper bpf_xdp_adjust_head() on mlx5 driver.
Fixes: 39d6443c8d ("mlx5, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL")
Reported-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
VNIC protocol version is reported in big-endian format, but it
is not byteswapped before logging. Fix that, and remove version
comparison as only one protocol version exists at this time.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous refactoring missed some locations the flags were renamed
but not moved from the previous flower_ext_feats to the new flower_en_feats
variable. This lead to the FLOW_MERGE and LAG features not being enabled.
Fixes: e09303d3c4 ("nfp: flower: renaming of feature bits")
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP imx8 family like imx8mp/imx8dxl chips support Synopsys MAC 5.10a IP.
This patch adds settings for NXP imx8 glue layer:
- clocks
- dwmac address width
- phy interface mode selection
- adjust rgmii txclk rate
v2:
- adjust code sequences in order to have reverse christmas
tree local variable ordering.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "snps,dwmac-5.10a" compatible string for 5.10a version that can
avoid to define some plat data in glue layer.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be there 2 switches spi/spi2.0 and spi/spi2.1 in a cross-chip setup,
both under the same VLAN-filtering bridge, both in the
SJA1105_VLAN_BEST_EFFORT state.
If we try to change the VLAN state of one of the switches (to
SJA1105_VLAN_FILTERING_FULL) we get the following error:
devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value
false cmode runtime
[ 38.325683] sja1105 spi2.1: Not allowed to overcommit frame memory.
L2 memory partitions and VL memory partitions share the
same space. The sum of all 16 memory partitions is not
allowed to be larger than 929 128-byte blocks (or 910
with retagging). Please adjust
l2-forwarding-parameters-table.part_spc and/or
vl-forwarding-parameters-table.partspc.
[ 38.356803] sja1105 spi2.1: Invalid config, cannot upload
This is because the spi/spi2.1 switch doesn't support tagging anymore in
the SJA1105_VLAN_FILTERING_FULL state, so it doesn't need to have any
retagging rules defined. Great, so it can use more frame memory
(retagging consumes extra memory).
But the built-in low-level static config checker from the sja1105 driver
says "not so fast, you've increased the frame memory to non-retagging
values, but you still kept the retagging rules in the static config".
So we need to rebuild the VLAN table immediately before re-uploading the
static config, operation which will take care, based on the new VLAN
state, of removing the retagging rules.
Fixes: 3f01c91aab ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q sub-VLANs")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
net/mlx5: Add support in forward to namespace
{IB/net}/mlx5: Simplify don't trap code
net/mlx5: Replace zero-length array with flexible-array
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The drivers reports EINVAL to userspace through netlink on invalid meta
match. This is confusing since EINVAL is usually reserved for malformed
netlink messages. Replace it by more meaningful codes.
Fixes: 6d65bc64e2 ("net/mlx5e: Add mlx5e_flower_parse_meta support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change MLX5_TC_CT config dependencies to include MLX5_ESWITCH instead of
MLX5_CORE_EN && NET_SWITCHDEV, which are already required by MLX5_ESWITCH.
Without this change mlx5 fails to compile if user disables MLX5_ESWITCH
without also manually disabling MLX5_TC_CT.
Fixes: 4c3844d9e9 ("net/mlx5e: CT: Introduce connection tracking")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add a call to mlx5e_reset_rx/tx_moderation() when enabling/disabling
adaptive moderation, in order to select the proper default values.
In order to do so, we separate the logic of selecting the moderation values
and setting moderion mode (CQE/EQE based).
Fixes: 0088cbbc4b ("net/mlx5e: Enable CQE based moderation on TX CQ")
Fixes: 9908aa2929 ("net/mlx5e: CQE based moderation")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change type of active_fec to u32 to match the type expected by
mlx5e_get_fec_mode. Copy active_fec and configured_fec values to
unsigned long before preforming bitwise manipulations.
Take the same approach when configuring FEC over 50G link modes: copy
the policy into an unsigned long and only than preform bitwise
operations.
Fixes: 2132b71f78 ("net/mlx5e: Advertise globaly supported FEC modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On tunnel decap rule insertion, the indirect mechanism will attempt to
offload the rule on all uplink representors which will trigger the
"devices are not on same switch HW, can't offload forwarding" message
for the uplink which isn't on the same switch HW as the VF representor.
The above flow is valid and shouldn't cause warning message,
fix by removing the warning and only report this flow using extack.
Fixes: 321348475d ("net/mlx5e: Fix allowed tc redirect merged eswitch offload cases")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently a Linux system with the mlx5 NIC always crashes upon
hibernation - suspend/resume.
Add basic callbacks so the NIC could be suspended and resumed.
Fixes: 9603b61de1 ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We need to call phy_restore_page() even if phy_select_page() fails.
Otherwise we are holding the phy_lock_mdio_bus() lock. This requirement
is documented at the start of the phy_select_page() function.
Fixes: a618e86da9 ("net : phy: marvell: Speedup TDR data retrieval by only changing page once")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYs using the vsc8574_probe fail to be initialized and their
config_init return -EIO leading to errors like:
"could not attach PHY: -5".
This is because when the conversion of the MSCC PHY driver to use the
shared PHY package helpers was done, the base address retrieval and the
base PHY read and write helpers in the driver were modified. In
particular, the base address retrieval logic was moved from the
config_init to the probe. But the vsc8574_probe was forgotten. This
patch fixes it.
Fixes: deb04e9c0f ("net: phy: mscc: use phy_package_shared")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The desc pointer is set but not used. Remove it.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-05-28
This series contains updates to e1000, e1000e, igc, igb, ixgbe and i40e.
Takashi Iwai, from SUSE, replaces some uses of snprintf() with
scnprintf() since the succeeding calls may go beyond the given buffer
limit in i40e.
Jesper Dangaard Brouer fixes up code comments in i40e_xsk.c
Xie XiuQi, from Huawei, fixes a signed-integer-overflow warning ixgbe
driver.
Jason Yan, from Huawei, converts '==' expression to bool to resolve
warnings, also fixed a warning for assigning 0/1 to a bool variable in
the ixgbe driver. Converts functions that always return 0 to void in the
igb and i40e drivers.
YueHaibing, from Hauwei, cleans up dead code in ixgbe driver.
Sasha cleans up more dead code which is not used in the igc driver.
Added receive error counter to reflect the total number of non-filtered
packets received with errors. Fixed a register define name to properly
reflect the register address being used.
Andre updates the igc driver to reject NFC rules that have multiple
matches, which is not supported in i225 devices. Updates the total
number of NFC rules supported and added a code comment to explain what
is supported.
Punit Agrawal, from Toshiba, relaxes the condition to trigger a reset
for ME, which was leading to inconsistency between the state of the
hardware as expected by the driver in e1000e.
Hari, from the Linux community, cleaned up a code comment in the e1000
driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
'Commit dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload
support")' added support for encapsulation offload. However, while
preparing inner tso packet, it uses reference to outer ip headers.
This patch fixes this issue by using correct reference for inner
headers.
Fixes: dacce2be33 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Update range request API;
* Add ACPI DSM support;
* Support enabling 5.2GHz bands in Indonesia via ACPI;
* Bump FW API version to 56;
* TX queues refactoring started;
* Fix one memory leak;
* Some other small fixes and clean-ups;
-----BEGIN PGP SIGNATURE-----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=nlI2
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2020-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Third set of iwlwifi patches intended for v5.8
* Update range request API;
* Add ACPI DSM support;
* Support enabling 5.2GHz bands in Indonesia via ACPI;
* Bump FW API version to 56;
* TX queues refactoring started;
* Fix one memory leak;
* Some other small fixes and clean-ups;
# gpg: Signature made Fri 29 May 2020 10:38:28 AM EEST using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
SD8997 firmware sends TLV_TYPE_MAX_CONN with struct hw_spec_max_conn to
inform kernel about maximum number of p2p connections and stations in AP
mode.
During initialization of SD8997 wifi chip kernel prints warning:
mwifiex_sdio mmc0:0001:1: Unknown GET_HW_SPEC TLV type: 0x217
This patch adds support for parsing TLV_TYPE_MAX_CONN (0x217) and sets
appropriate cfg80211 member 'max_ap_assoc_sta' from retrieved structure.
It allows userspace to retrieve NL80211_ATTR_MAX_AP_ASSOC_STA attribute.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123559.29028-1-pali@kernel.org
During initialization of SD8997 wifi chip kernel prints warnings:
mwifiex_sdio mmc0:0001:1: Unknown api_id: 3
mwifiex_sdio mmc0:0001:1: Unknown api_id: 4
This patch adds support for parsing all api ids provided by SD8997
firmware.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200521123444.28957-1-pali@kernel.org
The problem is that we always copy a minimum of ETH_ZLEN (60) bytes from
skb->data even when skb->len is less than ETH_ZLEN so it leads to a read
overflow.
The fix is to pad skb->data to at least ETH_ZLEN bytes.
Cc: <stable@vger.kernel.org>
Reported-by: Hu Jiahui <kirin.say@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200527184830.GA1164846@mwanda
Set MES watermark size to 0x50 for 43012. It fixes SDIO bus hang issue
when running at high throughput.
Signed-off-by: Double Lo <double.lo@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-6-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4354/4356 SDIO.
Also enable and configure F1 MesBusyCtrl. It would resolve random driver
crash issue.
Signed-off-by: Frank Kao <frank.kao@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-4-chi-hsien.lin@cypress.com
Set F2 blocksize to 256 bytes for 4373. It fixes DMA error while having
UDP bi-directional traffic. Also use a defined F1 MesBusyCtrl value.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529034938.124533-2-chi-hsien.lin@cypress.com
When wlcore_fw_status() returns an error code, a pairing
runtime PM usage counter decrement is needed to keep the
counter balanced. It's the same for all error paths after
wlcore_fw_status().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522044906.29564-1-dinghao.liu@zju.edu.cn
The CCK TX setting when switch channel will fix the CCK to
path A only, so if the antenna is configured to path B
(e.g. iw phy set antenna 0x2 0x3 "TX B/RX AB"), then the CCK
packets can never be delivered to the air if only path B is
connected with an antenna (it can possibly be transmitted
through path A, but as path B is configured, the expected
behavior is incorrect).
This can also solve the racing issue of CCK TX setting between
driver and firmware. The CCK TX setting in driver should be
removed. Otherwise, the CCK TX setting would be wrong when the
racing occurs.
Fixes: 297bcf8222 ("rtw88: add support for set/get antennas")
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522091234.24495-1-yhchuang@realtek.com
For older versions of gcc, the array = {0}; will cause warnings:
drivers/net/wireless/realtek/rtw88/rtw8822c.c: In function 'rtw8822c_power_trim':
>> drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning:
>> missing braces around initializer [-Wmissing-braces]
s8 bb_gain[2][8] = {0};
^
drivers/net/wireless/realtek/rtw88/rtw8822c.c:1039:2: warning: (near
initialization for 'bb_gain[0]') [-Wmissing-braces]
Fixes: 5ad4d8957b ("rtw88: set power trim according to efuse PG values")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522035521.12295-1-yhchuang@realtek.com
Connecting to an AP with WPA2 security may fail. The IQK
and the EAPOL 4-way handshake may overlap because the
driver does IQK right after assoc success.
For 802.11n devices, the IQK is done in the driver and it
could require more than 100ms to complete. During IQK, any
TX/RX events are paused. So if the EAPOL 4-way handshake
started before IQK finished, then the 1/4 and 2/4 part of
the handshake could be dropped. The AP will then issue
deauth with reason IEEE8021X_FAILED (23).
To resolve this, move IQK routine into managed TX prepare
(ieee80211_ops::mgd_prepare_tx()). The callback is called
before the managed frames (auth/assoc) are sent. This will
make sure that the IQK is completed before the handshake
starts. But don't do IQK during scanning because doing it
on each channel will take too long.
For 802.11ac devices, the IQK is done in firmware and it
takes less time to complete. Therefore we don't see a
failure during the EAPOL 4-way handshake. But it is still
worth moving the IQK into ieee80211_ops::mgd_prepare_tx().
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-4-yhchuang@realtek.com
Coex mechanism used to make BT have higher priority and more time to
transfer data when BT inquiry-page, which leads to poor WiFi performance.
Should take WiFi traffic into consideration. If the WiFi is having heavy
traffic, use another parameter to make sure WiFi has more chance to TX/RX,
while guarantee the priority of BT for inquiry. If the WiFi isn't busy
(connected or not), set proper parameter to fix originals.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-3-yhchuang@realtek.com
Without setting antenna control owner, the WiFi could be disconnected if
the BT has traffic. Because the antenna is switched to BT side for its
traffic, and the WiFi will have no chance to transfer data. Set control
owner to prevent WiFi disconnect issue.
Fixes: f5df1a8b43 ("rtw88: 8723d: Add 8723DE to Kconfig and Makefile")
Tested-by: You-Sheng Yang <vicamo.yang@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200529025009.2468-2-yhchuang@realtek.com
When wl12xx_cmd_role_disable() returns an error code,
a pairing runtime PM usage counter decrement is needed to
keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520130806.14789-1-dinghao.liu@zju.edu.cn
When wlcore_hw_interrupt_notify() returns an error code,
a pairing runtime PM usage counter decrement is needed to
keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520125724.12832-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124649.10848-1-dinghao.liu@zju.edu.cn
There are two error handling paths in this functon. When
wlcore_tx_work_locked() returns an error code, we should
decrease the runtime PM usage counter the same way as the
error handling path beginning from pm_runtime_get_sync().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124241.9931-1-dinghao.liu@zju.edu.cn
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200525134906.1672-1-rsalvaterra@gmail.com
All macro names for SDIO device IDs are prefixed by vendor name to which
device ID belongs. So for consistency add Broadcom string vendor prefix to
all Cypress macro names as they belong to SDIO Broadcom vendor ID.
Change also Cypress 43012 value from decimal do hexadecimal notation to be
consistent with all other values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-11-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Checks for device IDs are slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath10k.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200522144412.19712-9-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also replace generic MANUFACTURER macros by proper SDIO IDs macros.
Check for "AR6003 or later" is slightly modified to use SDIO device IDs.
This allows removal of all custom MANUFACTURER macros from ath6kl.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-8-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add _WLAN suffix to macro names for consistency with other Marvell macros.
These IDs represents wlan function of combo bt/wlan cards. Other functions
of these cards have different IDs.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200522144412.19712-4-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Range request version 10 keeps the same command size as version 9
but uses 2 reserved fields for the responder beacon interval and
station id (if exists).
For now, since the beacon interval of unassoc APs is unknown, use
a value of 100 TUs which is a common value for many APs.
While at it, remove the definition for CCMP_256 cipher, since this
is not supported.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.b7ccdad0805f.I59ea7f773caed85a66c61401066ae169008442e6@changeid
We don't want to have txq code in the PCIe transport code, so move all
the relevant elements to a new iwl_txq structure and store it in
iwl_trans.
spatch
@ replace_pcie @
struct iwl_trans_pcie *trans_pcie;
@@
(
-trans_pcie->queue_stopped
+trans->txqs.queue_stopped
|
-trans_pcie->queue_used
+trans->txqs.queue_used
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->txq
+trans->txqs.txq
|
-trans_pcie->cmd_queue
+trans->txqs.cmd.q_id
|
-trans_pcie->cmd_fifo
+trans->txqs.cmd.fifo
|
-trans_pcie->cmd_q_wdg_timeout
+trans->txqs.cmd.wdg_timeout
)
// clean all new unused variables
@ depends on replace_pcie @
type T;
identifier i;
expression E;
@@
- T i = E;
... when != i
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.a428d3c9d66f.Ie04ae55f33954636a39c98e7ae1e739c0507435b@changeid
Newer firmware versions will parse a few extra bits in the
context info to be able to determine whether we are using
bigger than 4k RBs, indicate 8k/12k to them if we actually
use those (e.g. for sniffer based on the module parameter).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.f83f994572ca.Ibcfd66c3f9b69e68a53b3b2df8331ffb225db655@changeid
ACPI Device Specific Method (DSM) allows standardized feature
configuration through the ACPI interface without the namespace
pollution of the usual mechanism (ACPI method for each feature).
Add generic function for evaluating DSM objects and function for
evaluating a DSM with no arguments and a single int return value.
also implement the required backport for UUID.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.c3242ff3ba5c.Icb48c8d61bede5dda7ef267bff10e4798e9dc77b@changeid
Continuous Double "the" in a comment. Changed it to single "the"
Signed-off-by: Hari <harichandrakanthan@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet this register address
used by Host Transmit Discarded Packet by MAC counter
and not by not applicable Carrier Extension Error counter.
This patch comes to fix this wrong definition.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet sequence error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Receive error counter reflect total number of non-filtered
packets received with errors. This includes: CRC error,
symbol error, Rx data error and carrier extend error.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Accordance to the i225 datasheet symbol error counter does not
applicable to the i225 device.
This patch comes to clean up this counter.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/i40e/i40e_adminq.c:699:13-21: Unneeded
variable: "ret_code". Return "0" on line 710
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.
Fix this by dropping the check for number of delay iterations.
While at it, also make __ew32_prepare() static as it's not used
anywhere else.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IGC supports a total of 32 rules. 16 MAC address based, 8 VLAN priority
based, and 8 Ethertype based. This patch fixes IGC_MAX_RXNFC_RULES
accordingly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The way Rx queue assignment based on mac address, Ethertype and VLAN
priority filtering operates in I225 doesn't allow us to properly support
NFC rules with multiple matches.
Consider the following example which assigns to queue 2 frames matching
the address MACADDR *and* Ethertype ETYPE.
$ ethtool -N eth0 flow-type ether dst <MACADDR> proto <ETYPE> queue 2
When such rule is applied, we have 2 unwanted behaviors:
1) Any frame matching MACADDR will be assigned to queue 2. It
doesn't matter the ETYPE value.
2) Any accepted frame that has Ethertype equals to ETYPE, no matter
the mac address, will be assigned to queue 2 as well.
In current code, multiple-match filters are accepted by the driver, even
though it doesn't support them properly. This patch adds a check for
multiple-match rules in igc_ethtool_is_nfc_rule_valid() so they are
rejected.
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Transmit underrun, late and excess collision flags not in use.
This patch comes to clean up these flags.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function always return 0 now, we can make it return void to
simplify the code. This fixes the following coccicheck warning:
drivers/net/ethernet/intel/igb/e1000_mac.c:728:5-12: Unneeded variable:
"ret_val". Return "0" on line 751
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit b5f69ccf67 ("ixgbe: avoid bringing rings up/down as macvlans are added/removed")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the following coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c:105:2-38: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No need to convert '==' expression to bool. This fixes the following
coccicheck warning:
drivers/net/ethernet/intel/ixgbe/ixgbe_common.c:68:11-16: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The comment above i40e_run_xdp_zc() was clearly copy-pasted from
function i40e_xsk_umem_setup, which is just above.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When calling hclge_parse_speed() fails, printing out the speed is
helpful for debugging.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some fields in struct hclge_dev which have not been used.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_CMDQ_INTR_SRC_REG and HCLGEVF_CMDQ_INTR_STS_REG are same
as HCLGEVF_VECTOR0_CMDQ_SRC_REG and HCLGEVF_VECTOR0_CMDQ_STAT_REG,
replace the former with the latter, and rename macro
HCLGEVF_VECTOR0_CMDQ_STAT_REG since 'stat' is not abbreviation of
'state'.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since field .uinfo in struct hnae3_handle never be used,
so remove it and its structure definition.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove HNAE3_RESTORE_CLIENT which is not needed now.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some fileds which defined in struct hns3_nic_priv,
but not used, and remove the related definition of struct
hns3_udp_tunnel and enum hns3_udp_tnl_type.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify field .gro_en in struct hclgevf_cfg_gro_status_cmd to u8
according to the UM, otherwise, it will overwrite the reserved
byte which may be used for other purpose.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify field .gro_en in struct hclge_cfg_gro_status_cmd to u8
according to the UM, otherwise, it will overwrite the reserved
byte which may be used for other purpose.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to improve code maintainability and readability, rewrite
the process of BDs' initialization in hclge_query_bd_num_cmd_send().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since parameters 'tso_mss_min' and 'tso_mss_max' only indicate
the minimum and maximum MSS, the hnae3_set_field() calls are
meaningless, remove them and change the type of these two
parameters to u16.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mutex destroy call in hclge_init_ae_dev() when fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the redundant 'goto' and return -ENOMEM directly, when
allocating memory for 'hdev' fails in hclge_init_ae_dev().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851_mll.c is replaced by ks8851_par.c, which is using common code
from ks8851.c, just like ks8851_spi.c . Remove this old ad-hoc driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement accessors for KS8851-16MLL/MLLI/MLLU parallel bus variant of
the KS8851. This is based off the ks8851_mll.c , which is a driver for
exactly the same hardware, however the ks8851.c code is much higher
quality. Hence, this patch pulls out the relevant information from the
ks8851_mll.c on how to access the bus, but uses the common ks8851.c
code. To make this patch reviewable, instead of rewriting ks8851_mll.c,
ks8851_mll.c is removed in a separate subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull all the SPI bus specific code into a separate file, so that it is
not mixed with the common code. Rename ks8851.c to ks8851_common.c. The
ks8851_common.c is linked with ks8851_spi.c now, so it can call the
accessors in the ks8851_spi.c without any pointer indirection.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register and FIFO accessors are bus specific, so is locking.
Implement callbacks so that each variant of the KS8851 can implement
matching accessors and locking, and use the rest of the common code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parallel bus variant does not need to use the TX interrupt at all
as it writes the TX FIFO directly with in .ndo_start_xmit, permit the
drivers to configure the interrupt enable bits.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the SPI version of the KS8851 requires a TX worker thread to pump
data via SPI, the parallel bus version can write data into the TX FIFO
directly in .ndo_start_xmit, as the parallel bus access is much faster
and does not sleep. Factor out this TX work flush part, so it can be
overridden by the parallel bus driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out common code into ks8851_probe_common() and
ks8851_remove_common() to permit both SPI and parallel
bus driver variants to use the common code path for
both probing and removal.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new struct ks8851_net_spi, which embeds the original
struct ks8851_net and contains the entries specific only to
the SPI variant of KS8851.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out this netif_rx_ni(), so it could be overridden by the parallel
bus variant of the KS8851 driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out bus access locking code into separate functions, this is done
in preparation for unifying the driver with the parallel bus one. The
parallel bus driver does not need heavy mutex locking of the bus and
works better with spinlocks, hence prepare these locking functions to
be overridden then.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RXFC register is the only one being read using 8-bit accessors.
To make it easier to support the 16-bit accesses used by the parallel
bus variant of KS8851, use 16-bit accessor to read RXFC register as
well as neighboring RXFCTR register.
Remove ks8851_rdreg8() as it is not used anywhere anymore.
There should be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the SPI variant of KS8851, the MAC address can be programmed with
either 8/16/32-bit writes. To make it easier to support the 16-bit
parallel option of KS8851 too, switch both the MAC address programming
and readout to 16-bit operations.
Remove ks8851_wrreg8() as it is not used anywhere anymore.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ks8851_rdreg32() is used only in one place, to read two registers
using a single read. To make it easier to support 16-bit accesses via
parallel bus later on, replace this single read with two 16-bit reads
from each of the registers and drop the ks8851_rdreg32() altogether.
If this has noticeable performance impact on the SPI variant of KS8851,
then we should consider using regmap to abstract the SPI and parallel
bus options and in case of SPI, permit regmap to merge register reads
of neighboring registers into single, longer, read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which
works for both SPI and platform drivers. This is done in preparation
for unifying the KS8851 SPI and parallel bus drivers.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device managed version of alloc_etherdev() to simplify the code.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver probe function already has a struct device *dev pointer
and can easily derive of_node pointer from it, pass the of_node pointer as
a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev.
This is the only reference to spidev in the function, so get rid of it.
This is done in preparation for unifying the KS8851 SPI and parallel bus
drivers.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev
in the interrupt handler. This is the only place which uses the spidev
in this function, so replace it with netdev_err() to get rid of it. This
is done in preparation for unifying the KS8851 SPI and parallel drivers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ndev variable to netdev for the sake of consistency.
No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull out the spi->dev into one common place in the function instead of
having it repeated over and over again. This is done in preparation for
unifying ks8851 and ks8851-mll drivers. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all vmxnet3 version 4 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 4, provided
the emulation advertises support for version 4.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vmxnet3 version 3 device supports checksum/TSO offload. Thus, vNIC to
pNIC traffic can leverage hardware checksum/TSO offloads. However,
vmxnet3 does not support checksum/TSO offload for Geneve/VXLAN
encapsulated packets. Thus, for a vNIC configured with an overlay, the
guest stack must first segment the inner packet, compute the inner
checksum for each segment and encapsulate each segment before
transmitting the packet via the vNIC. This results in significant
performance penalty.
This patch will enhance vmxnet3 to support Geneve/VXLAN TSO as well as
checksum offload.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With vmxnet3 version 4, the emulation supports multiqueue(RSS) for
UDP and ESP traffic. A guest can enable/disable RSS for UDP/ESP over
IPv4/IPv6 by issuing commands introduced in this patch. ESP ipv6 is
not yet supported in this patch.
This patch implements get_rss_hash_opts and set_rss_hash_opts
methods to allow querying and configuring different Rx flow hash
configurations.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmxnet3 is currently at version 3 and this patch initiates the
preparation to accommodate changes for version 4. Introduced utility
macros for vmxnet3 version 4 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a VF VSI calls ice_vsi_release() and ice_vsi_setup() it
subsequently clears/sets the VF cached variables for lan_vsi_idx and
lan_vsi_num. This works fine, but can be improved by handling this in
the VF specific VSI release and setup functions.
Also, when a VF VSI is setup too many parameters are passed that can be
derived from the VF. Fix this by only calling VF VSI setup with the bare
minimum parameters.
Also, add functionality to invalidate a VF's VSI when it's released
and/or setup fails. This will make it so a VF VSI cannot be accessed via
its cached vsi_idx/vsi_num in these cases.
Finally when a VF's VSI is invalidated set the lan_vsi_idx and
lan_vsi_num to ICE_NO_VSI to clearly show that there is no valid VSI
associated with this VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove VM/VF disable AQC (opcode 0x0C31) when resetting all VFs.
This is not required for CORER/GLOBR reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When resetting a VF the VLAN and MAC filter configurations need to be
replayed. Add helper functions for this purpose.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As the title says, use a function to set trust mode bit on reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some function names weren't very clear and some portions of VF creation
could be moved into functions for clarity. Fix this by renaming some
functions and move pieces of code into clearly name functions.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the same flow is used for VF VSI initialization/creation and VF
VSI reset. This makes the initialization/creation flow unnecessarily
complicated. Fix this by separating the initialization/creation of the
VF VSI from the reset flow.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Create a helper function for clearing VPGEN_VFRTRIG as this needs to be
done on reset to notify the VF that we are done resetting it. Also, it
needs to be done on SR-IOV initialization/creation in case it was left
in a bad state after SR-IOV tear down.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new function for checking if SR-IOV can be configured based on
the PF and/or device's state/capabilities. Also, simplify the flow in
ice_sriov_configure().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ice_ena_vf_mappings() does all of the VF's MSIX and queue
mapping in one function. This makes it hard to digest. Fix this by
creating a new function for enabling MSIX mappings and one for enabling
queue mappings.
Also, rename some variables in the functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove an unnecessary copy of vsi->info into ctxt->info in ice_vsi_init.
This line is essentially a no-op because ice_set_dflt_vsi_ctx performs
a memset to clear the info from the context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'nic_data' is no longer used outside of the #ifdef block
in efx_ef10_set_mac_address:
drivers/net/ethernet/sfc/ef10.c:3231:28: error: unused variable 'nic_data' [-Werror,-Wunused-variable]
struct efx_ef10_nic_data *nic_data = efx->nic_data;
Move the variable into a local scope.
Fixes: dfcabb0788 ("sfc: move vport_id to struct efx_nic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-27
This series contains updates to the ice driver only.
Jesse fixes a number of issues, starting with fixing the remaining
signed versus unsigned comparison issues. Cleaned up an unused code
define. Fixed the implementation of the manage MAC write command, to
simplify it by using a simple array to represent the MAC address when
writing it.
Paul fixes the setting of the VF default LAN address, by removing a
check that assumed that the address had been deleted and zeroed.
Surabhi prevents a memory leak on filter management initialization
failures and during queue initialization and buffer allocation failures.
Brett adds additional receive error counters that are reported by
ethtool. Fixed the enabling and disabling of VLAN stripping when the
PVID has been set.
Evan fixes a race condition between the firmware and software, which can
occur between the admin queue setup and the first command sent.
Marta fixes the driver when XDP transmit rings are destroyed, also make
sure the XDP transmit queues are also destroyed. Update the statistics
when XDP transmit programs are loaded and packets are sent. Changed the
number of XDP transmit queues to match the number of receive queues,
instead of matching the number of transmit queues.
Bruce avoids undefined behavior by not writing the 8-bit element
init_q_state with the associated internal-to-hardware field which is
122-bits.
Anirudh (Ani) refactors the receive checksum checks.
Krzysztof notifies the user if the fill queue is not long enough to
prepare all buffers before packet processing starts and allocates the
buffers during the NAPI poll.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb718348b8" fixed a similar problem.
Fixes: 07699f9a7c ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates highlights:
1) From Vu Pham (8): Support VM traffics failover with bonded VF
representors and e-switch egress/ingress ACLs
This series introduce the support for Virtual Machine running I/O
traffic over direct/fast VF path and failing over to slower
paravirtualized path using the following features:
__________________________________
| VM _________________ |
| |FAILOVER device | |
| |________________| |
| | |
| ____|_____ |
| | | |
| ______ |___ ____|_______ |
| | VF PT | |VIRTIO-NET | |
| | device | | device | |
| |_________| |___________| |
|___________|______________|________|
| |
| HYPERVISOR |
| ____|______
| | macvtap |
| |virtio BE |
| |___________|
| |
| ____|_____
| |host VF |
| |_________|
| |
_____|______ _____|_____
| PT VF | | host VF |
|representor| |representor|
|___________| |___________|
\ /
\ /
\ /
\ / _________________
\_______/ | |
_______|________ | V-SWITCH |
|VF representors |________________| (OVS) |
| bond | |________________|
|________________| |
________|________
| Uplink |
| representor |
|_________________|
Summary:
--------
Problem statement:
------------------
Currently in above topology, when netfailover device is configured using
VFs and eswitch VF representors, and when traffic fails over to stand-by
VF which is exposed using macvtap device to guest VM, eswitch fails to
switch the traffic to the stand-by VF representor. This occurs because
there is no knowledge at eswitch level of the stand-by representor
device.
Solution:
---------
Using standard bonding driver, a bond netdevice is created over VF
representor device which is used for offloading tc rules.
Two VF representors are bonded together, one for the passthrough VF
device and another one for the stand-by VF device.
With this solution, mlx5 driver listens to the failover events
occuring at the bond device level to failover traffic to either of
the active VF representor of the bond.
a. VM with netfailover device of VF pass-thru (PT) device and virtio-net
paravirtualized device with same MAC-address to handle failover
traffics at VM level.
b. Host bond is active-standby mode, with the lower devices being the VM
VF PT representor, and the representor of the 2nd VF to handle
failover traffics at Hypervisor/V-Switch OVS level.
- During the steady state (fast datapath): set the bond active
device to be the VM PT VF representor.
- During failover: apply bond failover to the second VF representor
device which connects to the VM non-accelerated path.
c. E-Switch ingress/egress ACL tables to support failover traffics at
E-Switch level
I. E-Switch egress ACL with forward-to-vport rule:
- By default, eswitch vport egress acl forward packets to its
counterpart NIC vport.
- During port failover, the egress acl forward-to-vport rule will
be added to e-switch vport of passive/in-active slave VF
representor
to forward packets to other e-switch vport ie. the active slave
representor's e-switch vport to handle egress "failover"
traffics.
- Using lower change netdev event to detect a representor is a
lower
dev (slave) of bond and becomes active, adding egress acl
forward-to-vport rule of all other slave netdevs to forward to
this
representor's vport.
- Using upper change netdev event to detect a representor unslaving
from bond device to delete its vport's egress acl forward-to-vport
rule.
II. E-Switch ingress ACL metadata reg_c for match
- Bonded representors' vorts sharing tc block have the same
root ingress acl table and a unique metadata for match.
- Traffics from both representors's vports will be tagged with same
unique metadata reg_c.
- Using upper change netdev event to detect a representor
enslaving/unslaving from bond device to setup shared root ingress
acl and unique metadata.
2) From Alex Vesker (2): Slpit RX and TX lock for parallel rule insertion in
software steering
3) Eli Britstein (2): Optimize performance for IPv4/IPv6 ethertype use the HW
ip_version register rather than parsing eth frames for ethertype.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl7PEFAACgkQSD+KveBX
+j4Z5Af+NYwihYZpQYBBN00K7Wu10XZ65u5MbGSDmzpdN62w0kKfjsJ70bb9aiws
h8LC7lspdMLRMMn9pWwFKshyF6RoSD9Ku3ZYhUbtj+hJLElAd9IwGt6pPKr8hPDd
9h+ZcBkacdhNwWKf7CKThic0c/0PLdVyzRysHxcQWKSMPCTdgiL5Z3PQHA0TM6J3
6Excs2z7kSuuyyxQ1cyWCaqSz4rqCrYyd8Ws4HOPhXgSbX14Q3mtMsBDayx2gHNW
rdVbaNN6s2o0TxbrCwd0AaNP3UWcnjNqu1ohxgJiSe8y+MHMoB0OMoO+6vQJnwNI
bzpZEioswV1zdgK3qNmXqbHOiHRSVQ==
=xM1D
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2020-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-05-26
Updates highlights:
1) From Vu Pham (8): Support VM traffics failover with bonded VF
representors and e-switch egress/ingress ACLs
This series introduce the support for Virtual Machine running I/O
traffic over direct/fast VF path and failing over to slower
paravirtualized path using the following features:
__________________________________
| VM _________________ |
| |FAILOVER device | |
| |________________| |
| | |
| ____|_____ |
| | | |
| ______ |___ ____|_______ |
| | VF PT | |VIRTIO-NET | |
| | device | | device | |
| |_________| |___________| |
|___________|______________|________|
| |
| HYPERVISOR |
| ____|______
| | macvtap |
| |virtio BE |
| |___________|
| |
| ____|_____
| |host VF |
| |_________|
| |
_____|______ _____|_____
| PT VF | | host VF |
|representor| |representor|
|___________| |___________|
\ /
\ /
\ /
\ / _________________
\_______/ | |
_______|________ | V-SWITCH |
|VF representors |________________| (OVS) |
| bond | |________________|
|________________| |
________|________
| Uplink |
| representor |
|_________________|
Summary:
--------
Problem statement:
------------------
Currently in above topology, when netfailover device is configured using
VFs and eswitch VF representors, and when traffic fails over to stand-by
VF which is exposed using macvtap device to guest VM, eswitch fails to
switch the traffic to the stand-by VF representor. This occurs because
there is no knowledge at eswitch level of the stand-by representor
device.
Solution:
---------
Using standard bonding driver, a bond netdevice is created over VF
representor device which is used for offloading tc rules.
Two VF representors are bonded together, one for the passthrough VF
device and another one for the stand-by VF device.
With this solution, mlx5 driver listens to the failover events
occuring at the bond device level to failover traffic to either of
the active VF representor of the bond.
a. VM with netfailover device of VF pass-thru (PT) device and virtio-net
paravirtualized device with same MAC-address to handle failover
traffics at VM level.
b. Host bond is active-standby mode, with the lower devices being the VM
VF PT representor, and the representor of the 2nd VF to handle
failover traffics at Hypervisor/V-Switch OVS level.
- During the steady state (fast datapath): set the bond active
device to be the VM PT VF representor.
- During failover: apply bond failover to the second VF representor
device which connects to the VM non-accelerated path.
c. E-Switch ingress/egress ACL tables to support failover traffics at
E-Switch level
I. E-Switch egress ACL with forward-to-vport rule:
- By default, eswitch vport egress acl forward packets to its
counterpart NIC vport.
- During port failover, the egress acl forward-to-vport rule will
be added to e-switch vport of passive/in-active slave VF
representor
to forward packets to other e-switch vport ie. the active slave
representor's e-switch vport to handle egress "failover"
traffics.
- Using lower change netdev event to detect a representor is a
lower
dev (slave) of bond and becomes active, adding egress acl
forward-to-vport rule of all other slave netdevs to forward to
this
representor's vport.
- Using upper change netdev event to detect a representor unslaving
from bond device to delete its vport's egress acl forward-to-vport
rule.
II. E-Switch ingress ACL metadata reg_c for match
- Bonded representors' vorts sharing tc block have the same
root ingress acl table and a unique metadata for match.
- Traffics from both representors's vports will be tagged with same
unique metadata reg_c.
- Using upper change netdev event to detect a representor
enslaving/unslaving from bond device to setup shared root ingress
acl and unique metadata.
2) From Alex Vesker (2): Slpit RX and TX lock for parallel rule insertion in
software steering
3) Eli Britstein (2): Optimize performance for IPv4/IPv6 ethertype use the HW
ip_version register rather than parsing eth frames for ethertype.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SJA1105, being AVB/TSN switches, provide hardware assist for the
Credit-Based Shaper as described in the IEEE 8021Q-2018 document.
First generation has 10 shapers, freely assignable to any of the 4
external ports and 8 traffic classes, and second generation has 16
shapers.
The Credit-Based Shaper tables are accessed through the dynamic
reconfiguration interface, so we have to restore them manually after a
switch reset. The tables are backed up by the static config only on
P/Q/R/S, and we don't want to add custom code only for that family,
since the procedure that is in place now works for both.
Tested with the following commands:
data_rate_kbps=67000
port_transmit_rate_kbps=1000000
idleslope=$data_rate_kbps
sendslope=$(($idleslope - $port_transmit_rate_kbps))
locredit=$((-0x80000000))
hicredit=$((0x7fffffff))
tc qdisc add dev swp2 root handle 1: mqprio hw 0 num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7
tc qdisc replace dev swp2 parent 1:1 cbs \
idleslope $idleslope \
sendslope $sendslope \
hicredit $hicredit \
locredit $locredit \
offload 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7611N is basically the same as MT7615N, except it only supports 5GHz
It is used by some TP-Link and Mercury wireless routers
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76 core uses ffs() to find the next free bit. This works well for 32 bit
architectures where BITS_PER_LONG is 32. ffs only checks 32 bit values, so
allocation fails on 64 bit architectures.
Additionally, the wcid mask array was too small in cases where the array
was not a multiple of BITS_PER_LONG.
Fix this by making the wcid mask array u32 instead and use DIV_ROUND_UP
for the size, just in case we ever bump it to a value that's not a multiple
of 32.
Reported-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix a NULL pointer dereference in mt7915_register_ext_phy since phy
data structure is allocated by mt76_alloc_phy routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix hw_scan with ssid_type for specified SSID only
The definition for ssid_type in current firmware is that
ssid_type BIT(2) set actually for specified SSID + wildcard SSID.
ssid_type BIT(2) and ssid_type_ext BIT(0) both set actually for
specified SSID only;
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are some spelling mistakes in some literal strings. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
switch to per-vif ps support since mt7615 offload firmware can handle it
properly. This patch allows enabling/disabling power-save support on p2p
interface
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
drivers/net/wireless/mediatek/mt76/mt7915/main.c:694:1: sparse:
sparse: context imbalance in 'mt7915_sta_rc_update' - wrong count at exit
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:303:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:304:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:305:43: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:319:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:327:35: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:345:41: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:355:33: sparse: sparse: cast to restricted __le32
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: sparse: invalid assignment: |=
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: left side has type unsigned int
drivers/net/wireless/mediatek/mt76/mt7915/mac.c:451:21: sparse: right side has type restricted __le32
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All drivers before MT7915 have a limit of 128 WCID entries. Stop relying
on ARRAY_SIZE(dev->mt76.wcid), since it no longer reflects that limit.
Fixes: 49e649c3e0 ("mt76: adjust wcid size to support new 802.11ax generation")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move assignment of .data1 and .data2 to a single place and fix overwriting
of values from the template
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable or disable OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
With this patch, we can get ~20% gain in OBSS OTA environment.
Tested-by: Evelyn Tsai <evelyn.tsai@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x02_mcu_msg_send is run just by mmio code so get rid of
mt76_is_mmio() check
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce remain_on_channel support to mt7615 driver if the device is
running offload firmware
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
If a UMEM is present on a queue when an interface/queue pair is being
enabled, the driver will try to prepare the Rx buffers in advance to
improve performance. However, if fill queue is shorter than HW Rx ring,
the driver will report failure after getting the last address from the
fill queue.
This still lets the driver process the packets correctly during the NAPI
poll, but leads to a constant NAPI rescheduling. Not allocating the
buffers in advance would result in a potential performance decrease.
Commit d57d76428a ("xsk: Add API to check for available entries in FQ")
provides an API that lets drivers check the number of addresses that the
fill queue holds.
Notify the user if fill queue is not long enough to prepare all buffers
before packet processing starts, and allocate the buffers during the
NAPI poll. If the fill queue size is sufficient, prepare Rx buffers in
advance.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the locking flow to support RX and TX locks, splitting
the single lock to two will allow inserting rules in parallel
for RX and TX parts of the FDB.
Locking the dr_domain will be done by locking the RX domain
and the TX domain locks, this is mostly used for control operations
on the dr_domain. When inserting rules for RX or TX the single
nic_doamin RX or TX lock will be used. Splitting the lock is safe since
RX and TX domains are logically separated from each other, shared
objects such the send-ring and memory pool are protected by locks.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding this lock will allow writing steering entries without
locking the dr_domain and allow parallel insertion.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The HW is optimized for IPv4/IPv6. For such cases, pending capability,
avoid matching on ethertype, and use ip_version field instead.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set ethertype match in a helper function as a pre-step towards
optimizing it.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use change upper event to detect slave representor from
enslaving/unslaving to/from lag device.
On enslaving event, call mlx5_enslave_rep() API to create, add
this slave representor shadow entry to the slaves list of
bond_metadata structure representing master lag device and use
its metadata to setup ingress acl metadata header.
On unslaving event, resetting the vport of unslaved representor
to use its default ingress/egress acls and rx rules with its
default_metadata.
The last slave will free the shared bond_metadata and its
unique metadata.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bonded slave representors' vports must share a unique metadata
for match.
On enslaving event of slave representor to lag device, allocate
new unique "bond_metadata" for match if this is the first slave.
The subsequent enslaved representors will share the same unique
"bond_metadata".
On unslaving event of slave representor, reset the slave
representor's vport to use its own default metadata.
Replace ingress acl and rx rules of the slave representors' vports
using new vport->bond_metadata.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce infrastructure to create unique metadata for match
for vport without depending on vport_num. Vport uses its
default metadata for match in standalone configuration but
will share a different unique "bond_metadata" for match with
other vports in bond configuration.
Using ida to generate unique metadata for match for vports
in default and bond configurations.
Introduce APIs to generate, free metadata for match.
Introduce APIs to set vport's bond_metadata and replace its
ingress acl rules with bond_metatada.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adding bond_metadata and its slave entries to represent a lag device
and its slaves VF representors. Bond_metadata structure includes a
unique metadata shared by slaves VF respresentors, and a list of slaves
representors slave entries.
On enslaving event, create a bond_metadata structure representing
the upper lag device of this slave representor if it has not been
created yet. Create and add entry for the slave representor to the
slaves list.
On unslaving event, free the slave entry of the slave representor.
On the last unslave event, free the bond_metadata structure and its
resources.
Introduce APIs to create and remove bond_metadata and its resources,
enslave and unslave VF representor slave entries.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When a bond device is created over one or more non uplink representors,
and when a flow rule is offloaded to such bond device, offload a rule
to the active lower device.
Assuming that this is active-backup lag, the rules should be offloaded
to the active lower device which is the representor of the direct
path (not the failover).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently offloading a rule over a tc block shared by multiple
representors fails because an e-switch global hashtable to keep
the mapping from tc cookies to mlx5e flow instances is used, and
tc block sharing offloads the same rule/cookie multiple times,
each time for different representor sharing the tc block.
Changing the implementation and behavior by acknowledging and returning
success if the same rule/cookie is offloaded again to other slave
representor sharing the tc block by setting, checking and comparing
the netdev that added the rule first.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Register a notifier block to handle netdev events for bond device
of non-uplink representors to support eswitch vports bonding.
When a non-uplink representor is a lower dev (slave) of bond and
becomes active, adding egress acl forward-to-vport rule of all slave
netdevs (active + standby) to forward to this representor's vport. Use
change lower netdev event to do this.
Use change upper event to detect slave representor unslaved from lag
device to delete its vport egress acl forward rule if any.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
By default, e-switch vport's egress acl just forward packets to its
counterpart NIC vport using existing egress acl table.
During port failover in bonding scenario where two VFs representors
are bonded, the egress acl forward-to-vport rule will be added to
the existing egress acl table of e-switch vport of passive/inactive
slave representor to forward packets to other NIC vport ie. the active
slave representor's NIC vport to handle egress "failover" traffic.
Enable egress acl and have APIs to create and destroy egress acl
forward-to-vport rule and group.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Restructure the eswitch ingress acl codes into eswitch directory
and different files:
. Acl ingress helper functions to acl_helper.c/h
. Acl ingress functions used in offloads mode to acl_ingress_ofld.c
. Acl ingress functions used in legacy mode to acl_ingress_lgy.c
This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Refactor the egress acl codes so that offloads and legacy modes
can configure specifically their own needs of egress acl table,
groups and rules. While at it, restructure the eswitch egress
acl codes into eswitch directory and different files:
. Acl egress helper functions to acl_helper.c/h
. Acl egress functions used in offloads mode to acl_egress_ofld.c
. Acl egress functions used in legacy mode to acl_egress_lgy.c
This patch does not change any functionality.
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We don't need both rx_status and rx_error parameters, as the latter is
a subset of the former. Remove rx_error completely and check the right bit
in rx_status.
Rename rx_status to rx_status0, and rx_status_err1 to
rx_status1. This naming more closely reflects the specification.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When writing the driver's struct ice_tlan_ctx structure, do not write the
8-bit element int_q_state with the associated internal-to-hardware field
which is 122-bits, otherwise the helper function ice_write_byte() will use
undefined behavior when setting the mask used for that write. This should
not cause any functional change and will avoid use of undefined behavior.
Also, update a comment to highlight this structure element is not written.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In current implementation number of XDP Tx queues is the same as
the number of transmit queues, which is not always true. This
patch changes this number to match the number of receive queues.
XDP programs are running on Rx rings, so what we actually need to
provide is the XDP Tx ring per each Rx ring so that the whole XDP
ecosystem is functional, e.g. if the result of XDP prog is XDP_TX
then you have the need to access the XDP Tx ring.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx program is loaded and packets are sent from
interface, VSI statistics are not updated. This patch adds
packets sent on Tx XDP ring to VSI ring stats.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP Tx rings are destroyed the number of XDP Tx queues
is not changing. This patch is changing this number to 0.
Signed-off-by: Marta Plantykow <marta.a.plantykow@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A race condition between FW and SW can occur between admin queue setup and
the first command sent. A link event may occur and FW attempts to notify a
non-existent queue. FW will set the critical error bit and disable the
queue. When this happens retry queue setup.
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, if the PVID is set in the VLAN handling section of the VSI
context the driver still allows VLAN stripping to be enabled/disabled.
VLAN stripping should only be modifiable when the PVID is not set. Fix
this by preventing VLAN stripping modification when PVID is set.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we are only including illegal_bytes and rx_crc_errors in the
PF netdev's rx_error counter. There are many more causes of Rx errors
that the device supports and reports via Ethtool. Accumulate all Rx
errors in the PF netdev's rx_error counter.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Handle memory leaks during control queue initialization and
buffer allocation failures. The macro ICE_FREE_CQ_BUFS is modified to
re-use for this fix.
Signed-off-by: Surabhi Boob <surabhi.boob@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The manage MAC write command was implemented in an overly complex way
that actually didn't work, as it wasn't symmetric to the manage MAC
read command, and was feeding bytes out of order to the firmware. Fix
the implementation by just using a simple array to represent the MAC
address when it is being written via firmware command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove is_zero_ether_add() check when setting the VF default LAN address.
This check assumed that the address had been delete and zeroed before
calling ice_vc_add_mac_addr(). Now the default LAN address will be set
to the last unicast MAC address added by the VF.
The default LAN address is reported by the PF via ndo_get_vf_config.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver had an unused define that can be removed. Found by
compiler -Werror=unused-macros check.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the remaining signed vs unsigned issues, which appear
when compiling with -Werror=sign-compare.
Many of these are because there is an external interface that is passing
an int to us (which we can't change) but that we (rightfully) store
and compare against as an unsigned in our data structures.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
No element named "client" exists within "struct ipa_endpoint".
It might be a heritage forgotten to be removed. Delete it now.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "transactio" -> "transaction". Also an alignment correction.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing CMDQ fails because of reset pending,
there is no hint for debugging, so adds a log for it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets will not pass through MAC during app loopback.
Therefore, it is meaningless to enable MAC while doing
app loopback. This patch removes this unnecessary action.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS RDMA driver will support VF device later, whose
re-initialization should be done after PF's. This patch
changes the order of hclge_reset_prepare_up() and
hclge_notify_roce_client(), so that PF's RoCE client
will be reinitialized before VF's.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent from initializing VF NIC client in reset handling state,
this patch adds resetting check in hclgevf_init_nic_client_instance().
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading timestamping operations not only
to the Ocelot switch (as already supported) but to compatible PHYs.
When both the PHY and the Ocelot switch support timestamping operations,
the PHY implementation is chosen as the timestamp will happen closer to
the medium.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ioctl to be implemented by the PHY, when a PHY is attached to the
Ocelot switch. In case the ioctl is a request to set or get the hardware
timestamp, use the Ocelot switch implementation for now.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
From the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in following patches
* branch 'mellanox/mlx5-next':
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
As explained in other commits before (b9cd75e668 and 87b0f983f6),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.
But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:
bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16
(note that port 5 is the CPU port and not the front-panel swp0).
So this hardware will send all VLANs as tagged towards the CPU.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_PM, the compiler warns about two unused functions:
drivers/net/ethernet/mediatek/mtk_star_emac.c:1472:12: error: unused function 'mtk_star_suspend' [-Werror,-Wunused-function]
drivers/net/ethernet/mediatek/mtk_star_emac.c:1488:12: error: unused function 'mtk_star_resume' [-Werror,-Wunused-function]
Mark these as __maybe_unused.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable new_pvid is being assigned with a value that is never read,
the following if statement updates new_pvid with a new value in both
of the if paths. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_addr field in desc_data must not be overwritten until after the
new skb is mapped. Currently we do replace it with uninitialized value
in error path. This change fixes it by moving the assignment before the
label to which we jump after mapping or allocation errors.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer br_dev is being initialized with a value that is never read
and is being updated with a new value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change the correct value for the used counter is calculated
but not stored nor, therefore, propagated to user-space. In use-cases such
as OVS use-case at least this results in active flows being removed from
the hardware datapath. Which results in both unnecessary flow tear-down
and setup, and packet processing on the host.
This patch addresses the problem by saving the calculated used value
which allows the value to propagate to user-space.
Found by inspection.
Fixes: aa6ce2ea0c ("nfp: flower: support stats update for merge flows")
Signed-off-by: Heinrich Kuhn <heinrich.kuhn@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.
Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a ton of minor checkpatch errors/warnings and remove version
printing at module init/when device is found and use MODULE_VERSION
instead. Also modifying the RTL8029 PCI string to include the compatible
RTL8029AS nic.
The only mayor issue remaining is the missing SPDX tag, but since the
exact version of the GPL is not stated anywhere inside the file, its
impossible to add such a tag at the moment.
But maybe it is possible, since 8390.h states Donald Becker's 8390
drivers are licensed under GPL 2.2 only (= GPL-2.0-only ?).
The kernel module containing this patch compiles and runs without
problems on a RTL8029AS-based NE2000 clone card with kernel 5.7.0-rc6.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has a trap for IPv6 packets that need be routed and have a
unicast link-local destination IP (i.e., fe80::/10). This allows mlxsw
to ignore link-local routes, as the packets will be trapped to the CPU
in any case.
However, since link-local routes are not programmed, it is possible for
routed packets to hit the default route which might also be programmed
to trap packets. This means that packets with a link-local destination
IP might be trapped for the wrong reason.
To overcome this, allow programming link-local prefix routes (usually
one fe80::/64 per-table), so that the packets will be forwarded until
reaching the link-local trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bidirectional Forwarding Detection (BFD) provides "low-overhead,
short-duration detection of failures in the path between adjacent
forwarding engines" (RFC 5880).
This is accomplished by exchanging BFD packets between the two
forwarding engines. Up until now these packets were trapped via the
general local delivery (i.e., IP2ME) trap which also traps a lot of
other packets that are not as time-sensitive as BFD packets.
Expose dedicated traps for BFD packets so that user space could
configure a dedicated policer for them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 packets that need to be forwarded and have a link-local source IP are
dropped by the kernel and an ICMPv6 "Destination unreachable" is sent to
the sending host.
As such, change the trap group of such packets so that they do not
interfere with IPv6 management packets. In the future this trap will be
exposed as an exception via devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven