This is just a helper function to go from the mac80211
station struct to our internal one, to later allow us
to avoid temporary 'mvmsta' variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The transport layer doesn't need to know the TX_CMD id.
It can be set by the op_mode.
The transport layer still needs to know the layout of the
Tx command because of alignment issues and because of the
scratch pointer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some NICs embedded in platforms that have only 16 Tx queues,
this affect the mapping of the Tx queues.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enable rs algorithm to use VHT rates and use 80Mhz.
This enables reaching VHT rates which wasn't possible.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of the non-QoS seqno for each station,
query the firmware when suspending, that's more efficient. As
this can fail, move the station ID mangling later in the code.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of drivers check the frame protocol for ETH_P_PAE,
for various reasons (like making those more reliable).
Add a new flags bitmap to the TX control info and a new
flag indicating the control port protocol is in use to
let all drivers also apply such logic to other control
port protocols, should they be configured.
Also use the new flag in the iwlwifi drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently after sending EAPOL frame FW transition to power saving mode
within 10 or 100 msec (as specified by power table command). According
to new requirement this timeout for a specific EAPOL frame must be
controlled by the driver by setting tx_pm_timeout field of TX_CMD to 2
(PM_FRAME_ENUM_MGMT). This value corresponds to 32 msec timeout.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fw is unreliable in all the cases in which the packet
wasn't sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multicast, there is no retries nor RTS since there is no
specific recipient that can ACK or send CTS. This means
that we must not use the rate scale table for multicast
frames.
This true for any frame that doesn't have a valid
ieee80211_sta pointer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow, the Tx flags for BAR were completely wrong.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the counter for non-AMPDU frames to mvm. It is needed
for the drain flow which happens once the ieee80211_sta has
been freed, so keeping it in iwl_mvm_sta which is embed into
ieee80211_sta is not a good idea.
Also, since its purpose it to remove the STA in the fw only
after all the frames for this station have exited the shared
Tx queues, we need to decrement it in the reclaim flow. This
flow can happen after ieee80211_sta has been removed, which
means that we have no iwl_mvm_sta there. So we can't know
what is the vif type. Hence, we know audit these frames for
all the vif types.
In order to avoid spawning sta_drained_wk all the time, we
now check that we are in a flow in which draining might
happen - only when mvmsta is NULL. This is better than
previous code that would spawn sta_drained_wk all the time
in AP mode.
Cc: stable@vger.kernel.org [3.9]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 332235427a
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"
I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.
Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This caused issues with tracing as it's longer than
the buffer size used there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
7000.c was released as GPL only by mistake: it should be
dual licensed - GPL / BSD.
The file that contains the license in the kernel is COPYING
and not LICENSE.GPL.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the sequence number arithmetic code from mac80211 to
ieee80211.h so others can use it. Also rename the functions
from _seq to _sn, they operate on the sequence number, not
the sequence_control field.
Also move macros to convert the sequence control to/from
the sequence number value from various drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flow happens when we get a failed single Tx response
on an AMPDU queue. In this case, the frame won't be sent
any more. So we need to move the window on the recipient
side. This is done by a BAR.
Now if we are in the following case: 10, 12 and 13 are ACKed
and 11 isn't.
10 11 12 13.
V X V V
Then, 11 will be sent 16 times as an MPDU (as oppsed to
A-MPDU). If this failed, we are entering the flow described
above. So we need to send a BAR with ssn = 12.
But in this case, the scheduler will tell us to free frames
up to 13 (included).
So, it is perfectly possible to get a failed single Tx
response on an AMPDU queue that makes the scheduler's ssn
jump by more than 1 single packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With new transports coming up, move to threaded
interrupt handling now. This has the advantage
that we can use the same locking scheme with all
different transports we may need to implement.
Note that the TX path obviously still runs in a
tasklet, so some spin_lock() calls need to change
to spin_lock_bh() calls to properly lock out the
TX path.
In my test on a Calpella platform this has no
impact on throughput or latency.
Also add lockdep annotations to avoid lockups due
to catch sending synchronous commands or using
locks that connect with them from the irq thread.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware revisions have a completely new
firmware API. This is the new driver for this
new API.
I've listed the people who directly contributed
code, but many others from various teams have
contributed in other ways.
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Amit Beka <amit.beka@intel.com>
Cc: Amnon Paz <amnonx.paz@intel.com>
Cc: Assaf Krauss <assaf.krauss@intel.com>
Cc: David Spinadel <david.spinadel@intel.com>
Cc: Dor Shaish <dor.shaish@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Eytan Lifshitz <eytan.lifshitz@intel.com>
Cc: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg