Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/dhd_bus.h
drivers/net/wireless/rtlwifi/rtl8188ee/phy.h
drivers/net/wireless/rtlwifi/rtl8192ce/phy.h
drivers/net/wireless/rtlwifi/rtl8192de/phy.h
drivers/net/wireless/rtlwifi/rtl8723ae/phy.h
Just some minor conflicts between the wireless-next changes
and Joe Perches's "extern" removal from function prototypes
in header files.
John W. Linville says:
====================
Regarding the Bluetooth bits, Gustavo says:
"The big work here is from Marcel and Johan. They did a lot of work
in the L2CAP, HCI and MGMT layers. The most important ones are the
addition of a new MGMT command to enable/disable LE advertisement
and the introduction of the HCI user channel to allow applications
to get directly and exclusive access to Bluetooth devices."
As to the ath10k bits, Kalle says:
"Bartosz dropped support for qca98xx hw1.0 hardware from ath10k, it's
just too much to support it. Michal added support for the new firmware
interface. Marek fixed WEP in AP and IBSS mode. Rest of the changes are
minor fixes or cleanups."
And also:
"Major changes are:
* throughput improvements including aligning the RX frames correctly and
optimising HTT layer (Michal)
* remove qca98xx hw1.0 support (Bartosz)
* add support for firmware version 999.999.0.636 (Michal)
* firmware htt statistics support (Kalle)
* fix WEP in AP and IBSS mode (Marek)
* fix a mutex unlock balance in debugfs file (Shafi)
And of course there's a lot of smaller fixes and cleanup."
For the wl12xx bits, Luca says:
"Here are some patches intended for 3.13. Eliad is upstreaming a bunch
of patches that have been pending in the internal tree. Mostly bugfixes
and other small improvements."
Along with that...
Arend and friends bring us a batch of brcmfmac updates, Larry Finger
offers some rtlwifi refactoring, and Sujith sends the usual batch of
ath9k updates. As usual, there are a number of other small updates
from a variety of players as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix for TCP iperf from Windows to Linux stall after about 1sec
Hardware reports false errors in some situations:
Microsoft IP stack, in violation of RFC 1624, set TCP checksum that should be 0x0
as 0xffff. hardware report Rx csum error. If HW csum absolutely trusted,
this frame can be never received, as re-transmitted one will have same csum problem.
In addition, it mess up block ack reorder buffer, as if packet dropped, it is not score boarded
there.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In production code, don't use -Werror,
as it causes random compilation failures due to compiler version and options used.
With every new version of gcc, it becomes stricter and report more warnings.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for TCP and UDP HW checksum offloading.
RX chain is allways configured for offload mode.
In case of checksum error in RX path the DMA L4 error bit(5)
will be set to 1 and driver will drop the packet.
TX checksum offloading is configrable (ethtool -K).
TX descriptors are configured for checksum offload according
to the SKB protocol type (TCP/UDP, IPV4/6), Upon mismatch drop
the TX packet (checksum required but not TCP/UDP IPV4/6 type).
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Release fragments in the order of allocation; including one for skb head
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Finish all SW context modifications prior to notifying hardware
It used to be race condition: if HW finish Tx and issue Tx completion IRQ very fast,
prior to SW context update in wil_tx_vring, Tx completion will mis-handle descriptor, as
SW part will have no skb pointer stored.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable adding more data to the SW context.
For now, add flag "mapped_as_page", to separate decisions on free-ing skb
and type of DMA mapping.
This allows linking skb itself to any descriptor of fragmented skb.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to modify HW descriptor, as it will be re-initialized on Tx.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When destroying Rx vring, branch for Rx used wrong Tx descriptor:
while SW context was taken for "head", HW descriptor was, by mistake,
taken from "tail"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building driver wil6210 in 3.10 and 3.11 kernels yields the following errors:
CC [M] drivers/net/wireless/ath/wil6210/debugfs.o
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_print_ring':
drivers/net/wireless/ath/wil6210/debugfs.c:163:11: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
drivers/net/wireless/ath/wil6210/debugfs.c: In function 'wil_txdesc_debugfs_show':
drivers/net/wireless/ath/wil6210/debugfs.c:429:10: error: pointer targets in passing argument 5 of 'hex_dump_to_buffer' differ in signedness [-Werror=pointer-sign]
sizeof(printbuf), false);
^
In file included from include/linux/kernel.h:13:0,
from include/linux/cache.h:4,
from include/linux/time.h:4,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/net/wireless/ath/wil6210/debugfs.c:17:
include/linux/printk.h:361:13: note: expected 'char *' but argument is of type 'unsigned char *'
extern void hex_dump_to_buffer(const void *buf, size_t len,
^
cc1: all warnings being treated as errors
make[5]: *** [drivers/net/wireless/ath/wil6210/debugfs.o] Error 1
make[4]: *** [drivers/net/wireless/ath/wil6210] Error 2
make[3]: *** [drivers/net/wireless/ath] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
These errors are fixed by changing the type of the buffer from "unsigned char *" to "char *".
Reported-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.10]
Cc: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Map BIT 9 in TX DMA DWARD 0 as HW write back option.
We must turn on this option in the last TX descriptor,
this is required for old HW compatability.
This option indicate to HW that WB is required for this descriptor.
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vring index (MAC queue id) must be set in all TX descriptors
otherwise HW will fail to release descriptors for a specific vring
(disconnect or vring switch flows).
This is normally occurs when fragmentation required, if vring index
will not be the same for all SKB descriptors HW will fail to flush
this MAC queue.
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WMI PCP Start flow should not be handled through:
net_device_ops->ndo_open()->wil_up()->__wil_up()
because it missing mandatory FW parameters (SSID,Channel,IEs, Security...).
Prior to AP starting __wil_up() may be called with iftype set
cfg80211_ops->change_virtual_intf(NL80211_IFTYPE_AP or STATION)
depend on the application hostapd/wpa_supplicant/iw.
there should not be an attempt to start an AP flow,
AP/PCP start flow will be started latter by cfg80211_ops->start_ap().
Signed-off-by: Kirshenbaum Erez <erezk@wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tracing in wil6210 is activated with WIL6210_TRACING and not with
ATH6KL_TRACING, this is used for the ath6kl driver. Rename the config
option.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
at the vring initialisation, memory pool get allocated in the FW.
Make it 1-st because FW need this memory pool to precess
next commands
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No more need for special processing of EAPOL, FW can now send EAPOL frames
using normal Tx queue for TID 0
This fixes "schedule while atomic" bug - start_xmit called in softirq context;
while WMI mechanism that was used may sleep.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting secure AP, in some cases wpa_s provides probe template but not
probe/assoc IE's. In this case, derive missing IE's from probe.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report FC from the frame itself, as auxiliary information includes
only frame subtype. This is preparation for future changes, when
DMG beacon (extension frame) may be reported through wmi_evt_rx_mgmt()
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
map card's back-door debug data
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It may take up to 3500ms for the FW to start AP/PCP. Increase accordingly,
adding some safety margin.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sme_state is private wdev's variable.
Track connection state internally
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WMI commands wants channel index, that is channel - 1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kfree_skb() instead of kfree() to free sk_buff.
Introduced by commit e270045b56
(wil6210: Sanity check for reported DMA length)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packet drop may be caused by various flows, like disconnect
while Tx packets was queued; this should not lead to stopping
of the Tx queue, or all Tx get stalled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Introduce common code for Tx/Rx descriptor physical address set/parse
- Fix endianness for address fields
- consistent descriptor naming: '_d' for non-cached memory, 'd' for cached copy
- wil_tx_desc_map now modify cached copy, no need for 'volatile'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce NAPI for Rx and Tx completion.
This fixes packet reordering that happens when Rx handled right in
the IRQ: netif_rx puts packet in 'percpu' queue, then network stack
fetches packets from 'percpu' queues for processing, with different
pattern of queue switching. As result, network stack see packets
in different order. This causes hard to understand TCP throughput
degradation in about 30min
Complete polling if only one packet was processed - this eliminates
empty polls that would be otherwise done at the end of each burst
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move packet dump to the earliest location where it is known to have
valid data.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If Rx descriptor contains garbage, it is possible to access memory beyond
allocated buffer.
Check this condition and drop Rx if reported length is
unreasonable large
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware uses little endian for the Tx/Rx descriptors field 'length',
do appropriate conversions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Helpers to fetch various fields from the Rx descriptor
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Original Tx descriptor stored is in non-cached area for DMA;
copy it to the cached memory to speed-up access
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
vring size is known from the beginning, fill it immediately
in the struct initializer
This is minor optimization that reduces code size.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rx descriptors stored in non-cacheable memory area for DMA.
Non-cacheable memory causes long access time from CPU.
Copy rx descriptor to the skb->cb, and use this copy.
It provides faster memory access, and will be usefull to keep
Rx information for later processing (BACK reorder)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware got support for temperature measurement.
There are 2 temperature sensors: MAC and radio
"not available" temperature - reported by FW as 0 or ~0
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust driver for changes in the FW API.
Noticeable changes in the FW are:
- temperature sensing
- infrastructure for multiple connections
- infrastructure for P2P
- signal strength indication
This commit introduces only changes that are required to support same functionality
as previous firmware, no new features.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware allows for shorter SW reset procedure.
After SW reset, FW raises "fw done" IRQ, at this
moment mailbox control structures are initialized, driver caches it.
New status bit wil_status_reset_done introduced to track completion
of the reset. It is set by "fw ready" irq, and required for WMI rx flow
to access control structures.
WMI Tx flow protected by other status bit, wil_status_fwready. It can't
be set before wil_status_reset_done is set by design.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wolfram Sang