Renaming variables, no functional changes
Event trbs on the event ring cointain a pointer to the transfer trb
on a endpoint ring that caused the event.
The naming has been very confusing as the event trb was called "event"
and the endpoint transfer trb was called "event_trb".
rename all variables that are realated to the endpoint transfer trb
from event_* to ep_*
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mostly refactoring, but does also change error message if
we get a bad length in the event trb.
Adds a helper function to sum trb lengths of partial TDs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor pricess_ctrl_tx() to make it more readable
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only check for the URB_SHORT_NOT_OK urb flag to set the urb status
to -EREMOTEIO for transfers that didn't transfer all data.
This will be done in __usb_hcd_giveback() for other than isoc tranfers,
so remove the redundant check from xhci.
Also fix a couple split lines in debug messages to make them greppable.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
replace the complex check for noop with a simple helper
Improve code readability
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the trb_is_link() and link_trb_toggles_cycle() helpers to
make the code more readable
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no point in trying to reset the host controller by writing
to its registers if host is removed and registers just return 0xffffffff
bail out and return -ENODEV instead
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old error message always stated that host was not halted
even after trying a certain time.
Host may fail the halt immediately as well with -ENODEV if device
is removed and returns 0xffffffff.
Use a more generic error message and show return value to know if we
failed with -ETIMEDOUT or -ENODEV
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fist function called in xhci_halt is xhci_quiesce, so no point
in calling it twice
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: stable@vger.kernel.org
Never seen XHCI auto handoff working on TI and RENESAS cards.
Eventually, we force handoff. This code forces the handoff
unconditionally. It saves 5 seconds boot time for each card.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove this macro
from the driver.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
usb_endpoint_maxp() is now returning maxpacket
correctly - iow only bits 10:0. We can finaly remove
XHCI's private GET_MAX_PACKET macro.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make IPPC register optional to support host side of dual-role mode,
due to it is moved into common glue layer for simplification.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Davinci OHCI host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
[Axel: adapted and rebased, fixed minor comments]
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Including mach/* is frowned upon in device drivers, so get rid of it.
This replaces usb20_clk and code that pokes CFGCHIP2 with a proper phy
driver.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the descriptor-based interface to manipulate GPIOs, instead of
the legacy integer-based interface.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This merges the vendor NEC case with the INTEL and AMD one,
as those 3 do exactly the same thing: disabling of the IO
watchdog.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes 10 timer wakeups per second. I'm running this patch for
a while now and haven't spotted any adverse effects.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset value of RWC is 0, set RemoteWakeupConnected bit explicitly
before calling ohci_run, it also fixes the issue that the mass
storage stick connected wasn't suspended when the system suspend.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.
This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SEAD-3 board is now probing its EHCI controller using the generic
EHCI driver & its generic-ehci device tree binding. Remove the unused
SEAD-3 specific EHCI code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This driver should initialize controller only, PHY initialization should
be handled by separated PHY driver. We already have phy-bcm-ns-usb2 in
place so let it makes its duty.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With LPAE config we don't have omap3 or omap4 selected for
omap5 variants.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warning:
drivers/usb/host/ohci-at91.c:141:15: warning:
symbol 'at91_dt_syscon_sfr' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return error code -ENOMEM from the usb_create_shared_hcd()
error handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ohci-omap doesn't need to include mach/irqs.h - nothing within this
driver needs anything from this header file. Remove this include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mach/hardware.h include doesn't seem to be necessary to build
ohci-sa1111, so let's remove it to kill off an unnecessary platform
specific include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The neponset is a daughter board for the Assabet platform, which has a
SA1111 chip on it. If we're initialising the SA1111 OHCI, and we're
part of a neponset, the host platform must be an Assabet.
This allows us to eliminate machine_has_neponset() from this driver,
replacing it instead with machine_is_assabet(), and killing the
mach/assabet.h include.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb controller does not manage correctly the suspend mode for
the ehci. In echi mode, there is no way to suspend without any
device connected to it. This is why this specific control is added
to fix this issue. Since the suspend mode works in ohci mode, this
specific control works by suspend the usb controller in ohci mode.
This specific control is by setting the SUSPEND_A/B/C fields of
SFR_OHCIICR(OHCI Interrupt Configuration Register) in the SFR
while the OHCI USB suspend.
This set operation must be done before the USB clock disabled,
clear operation after the USB clock enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently bcma-hcd driver handles 3 different bcma cores:
1) BCMA_CORE_USB20_HOST (0x819)
2) BCMA_CORE_NS_USB20 (0x504)
3) BCMA_CORE_NS_USB30 (0x505)
The first one was introduced years ago and so far was used on MIPS
devices only. All Northstar (ARM) devices were using other two cores
which allowed easy implementation of separated initialization paths.
It seems however Broadcom decided to reuse this old USB 2.0 controller
on some recently introduced cheaper Northstar BCM53573 SoCs. I noticed
this on Tenda AC9 (based on BCM47189B0 belonging to BCM53573 family).
There is no difference in this old controller core identification
between MIPS and ARM devices: they share the same id and revision. We
need different controller initialization procedure however.
To handle this add a check for architecture and implement required
initialization for ARM case.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
The workqueue "workqueue" has multiple workitems which may require
ordering. Hence, a dedicated ordered workqueue has been used.
Since the workqueue is not being used on a memory reclaim path,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPIO control register is divided into IOPINS1 and IOPINS2.
And low 4-bit of register is controls output.
So, this patch fixes wrong mask of GPIO output.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a rather simple controller, we just need to make sure USB is
powered (using GPIO pin) and reset bus core. Once this is done it's
safe to register XHCI controller and let it init PHY and do its magic.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
gcc warns about what first looks like a reference to an uninitialized
variable:
drivers/usb/host/xhci-ring.c: In function 'handle_cmd_completion':
drivers/usb/host/xhci-ring.c:753:4: error: 'ep_ring' may be used uninitialized in this function [-Werror=maybe-uninitialized]
xhci_unmap_td_bounce_buffer(xhci, ep_ring, cur_td);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-ring.c:647:20: note: 'ep_ring' was declared here
struct xhci_ring *ep_ring;
^~~~~~~
It's clear to see that the list_empty() check means it can never be
uninitialized, however it still looks wrong:
When ep->cancelled_td_list contains more than one entry, the
ep_ring variable will point to the ring that was retrieved
from the last urb, and we have to look it up again in the
second loop instead, which fixes the behavior and gets rid of the
warning too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
- Fixes: 0b52297 ("reset: Add support for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mo7m
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP. New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP. New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PT1e
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
No more users for it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting the only property that the driver needs using the
unified device property interface so it will be available
for all types of platforms, not just the ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's only used with rings that have link trbs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only used in one place, replace with trb_is_link() helper
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inc_deq() is called both for rings with link trbs and the event ring
without link trbs.
The last_trb() check in inc_deq() has a off by one error, going beyond
allocated array when checking if trb == [TRBS_PER_SEGMENT], and the whole
inc_deq() depend on this.
Rewrite the inc_deq() funciton, remove the faulty last_trb() helper, add
new last_trb_on_seg() and last_trb_on_ring() helpers
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new is_link_trb() function that only checks for link trbs.
We want to split generic last_trb() function which is used for both
event rings without link trbs, and endpoint and command rings with links.
This will allow us to easier check for link trbs added mid segments.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the event ring related checks in inc_enq()
Host hardware is the producer of events on the event ring,
driver will not queue anything, or call inc_enq() for the
event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.
Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.
For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TD fragments section 4.11.7.1 in xhci specs have additional requirements
on how trbs in TDs must be organized.
TD fragments shall not span transfer ring segments and TD fragments must
be packet aligned. Normally we don't care about TD fragments, on TD is one
big fragment, but if a TD spans ring segments it will be treated as two
fragments, and we need to comply with the alignment requirements.
For us this means that the payload data must be packet aligned in the
last trb before a link trb.
In most mass storage bulk tranfers we are lucky as the block size aligns
nicely with packet size, and there are no issues.
However, usb network adapters using scatterlists can hit this alignment
issue, and usbtest in kernel triggers this in minutes.
This patch is a partial solution, it solves the easy case when the last
trb before the link trb contains a packet boundary.
If that is the case then just split the trb at the boundary.
If not, then just print a debug message and continue as we have always
done, hoping for the best
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Queue trbs until all payload data in the urb is tranferred.
The actual number of trbs might need to change from the pre-calculated
number when the packet alignment restrictions for td fragments in
xhci 4.11.7.1 are taken into account.
Long term plan is to get rid of calculating the needed trbs in advance
all together. It's an unnecessary extra walk through the scatterlist.
This change also allows some bulk queue function simplifications
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only need to know if we are queuing the last trb for a TD when
calculating the td remainder field.
The total number of trbs left is not used.
We won't be able to trust the pre-calculated number of trbs used if we
need to align trb data by splitting or merging trbs in order to satisfy
comply with data alignment requirements in xhci specs section 4.11.7.1.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a zero-length packet is needed after a bulk transfer, then an
additional zero length TD was prepared before enqueueing the bulk transfer
This set up the zero packet TD structure with incorrect td->start_seg
and td->first_trb pointers.
Prepare the zero packet TD after the data bulk TD is enqueued instead.
It sets these pointers correctly.
This change also simplifies unnecessary complexity related to keeping
track of the last trb when enqueuing trbs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tiny change, a bit more readable.
The real reason for this change is that the coming td fragment work
had several over 80 lines character lines split just because of a few
extra characters in variable names.
no functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
instead of defining all functions as static inlines,
let's move them to udc-core and export them with
EXPORT_SYMBOL_GPL, that way we can make sure that
only GPL drivers will use them.
As a side effect, it'll be nicer to add tracepoints
to the gadget API.
While at that, also fix Kconfig dependencies to
avoid randconfig build failures.
Acked-By: Sebastian Reichel <sre@kernel.org>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 7150bc9b4d.
It is not correct, based on review from others.
Reported-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the Linux PCI core does not touch power state of PCI bridges and
PCIe ports when system suspend is entered. Leaving them in D0 consumes
power unnecessarily and may prevent the CPU from entering deeper C-states.
With recent PCIe hardware we can power down the ports to save power given
that we take into account few restrictions:
- The PCIe port hardware is recent enough, starting from 2015.
- Devices connected to PCIe ports are effectively in D3cold once the port
is transitioned to D3 (the config space is not accessible anymore and
the link may be powered down).
- Devices behind the PCIe port need to be allowed to transition to D3cold
and back. There is a way both drivers and userspace can forbid this.
- If the device behind the PCIe port is capable of waking the system it
needs to be able to do so from D3cold.
This patch adds a new flag to struct pci_device called 'bridge_d3'. This
flag is set and cleared by the PCI core whenever there is a change in power
management state of any of the devices behind the PCIe port. When system
later on is suspended we only need to check this flag and if it is true
transition the port to D3 otherwise we leave it in D0.
Also provide override mechanism via command line parameter
"pcie_port_pm=[off|force]" that can be used to disable or enable the
feature regardless of the BIOS manufacturing date.
Tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for shared platform controllers by using
devm_reset_control_get_shared_by_index instead of
of_reset_control_get_by_index.
Note we use the devm function because there is no
of_reset_control_get_shared_by_index, this also leads
to a nice cleanup of the cleanup code.
This brings the ehci-platform reset handling code inline
with ohci-platform.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least the EHCI/OHCI found on the Allwinnner H3 SoC needs multiple
reset lines, the controller will not initialize while the reset for
its companion is still asserted, which means we need to de-assert
2 resets for the controller to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to the save power consumption, as a workaround, suspend
forcibly the USB PORTA/B/C via set the SUSPEND_A/B/C bits of OHCI
Interrupt Configuration Register in the SFRs while OHCI USB suspend.
This suspend operation must be done before the USB clock is disabled,
resume after the USB clock is enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ehci compatible controllers have more than one reset signal lines,
e.g., Synopsys DWC USB2.0 Host-AHB Controller has two resets hreset_i_n
and phy_rst_i_n. Two more resets are added in this patch in order for
this kind of controller to use this driver directly.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a suspend/resume issue where the driver is blindly
calling ehci_suspend/resume functions when the ehci hasn't been setup.
This results in a crash during suspend/resume operations.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <pramod.gurav@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with commit 0b52297f22 ("reset: Add support for shared reset
controls") there is a reference count for reset control assertions. The
goal is to allow resets to be shared by multiple devices and an assert
will take effect only when all instances have asserted the reset.
In order to preserve backwards-compatibility, all reset controls become
exclusive by default. This is to ensure that reset_control_assert() can
immediately assert in hardware.
However, this new behaviour triggers the following warning in the EHCI
driver for Tegra:
[ 3.365019] ------------[ cut here ]------------
[ 3.369639] WARNING: CPU: 0 PID: 1 at drivers/reset/core.c:187 __of_reset_control_get+0x16c/0x23c
[ 3.382151] Modules linked in:
[ 3.385214] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.6.0-rc6-next-20160503 #140
[ 3.392769] Hardware name: NVIDIA Tegra SoC (Flattened Device Tree)
[ 3.399046] [<c010fa50>] (unwind_backtrace) from [<c010b120>] (show_stack+0x10/0x14)
[ 3.406787] [<c010b120>] (show_stack) from [<c0347dcc>] (dump_stack+0x90/0xa4)
[ 3.414007] [<c0347dcc>] (dump_stack) from [<c011f4fc>] (__warn+0xe8/0x100)
[ 3.420964] [<c011f4fc>] (__warn) from [<c011f5c4>] (warn_slowpath_null+0x20/0x28)
[ 3.428525] [<c011f5c4>] (warn_slowpath_null) from [<c03cc8cc>] (__of_reset_control_get+0x16c/0x23c)
[ 3.437648] [<c03cc8cc>] (__of_reset_control_get) from [<c0526858>] (tegra_ehci_probe+0x394/0x518)
[ 3.446600] [<c0526858>] (tegra_ehci_probe) from [<c04516d8>] (platform_drv_probe+0x4c/0xb0)
[ 3.455029] [<c04516d8>] (platform_drv_probe) from [<c044fe78>] (driver_probe_device+0x1ec/0x330)
[ 3.463892] [<c044fe78>] (driver_probe_device) from [<c0450074>] (__driver_attach+0xb8/0xbc)
[ 3.472320] [<c0450074>] (__driver_attach) from [<c044e1ec>] (bus_for_each_dev+0x68/0x9c)
[ 3.480489] [<c044e1ec>] (bus_for_each_dev) from [<c044f338>] (bus_add_driver+0x1a0/0x218)
[ 3.488743] [<c044f338>] (bus_add_driver) from [<c0450768>] (driver_register+0x78/0xf8)
[ 3.496738] [<c0450768>] (driver_register) from [<c010178c>] (do_one_initcall+0x40/0x170)
[ 3.504909] [<c010178c>] (do_one_initcall) from [<c0c00ddc>] (kernel_init_freeable+0x158/0x1f8)
[ 3.513600] [<c0c00ddc>] (kernel_init_freeable) from [<c0810784>] (kernel_init+0x8/0x114)
[ 3.521770] [<c0810784>] (kernel_init) from [<c0107778>] (ret_from_fork+0x14/0x3c)
[ 3.529361] ---[ end trace 4bda87dbe4ecef8a ]---
The reason is that Tegra SoCs have three EHCI controllers, each with a
separate reset line. However the first controller contains UTMI pads
configuration registers that are shared with its siblings and that are
reset as part of the first controller's reset. There is special code in
the driver to assert and deassert this shared reset at probe time, and
it does so irrespective of which controller is probed first to ensure
that these shared registers are reset before any of the controllers are
initialized. Unfortunately this means that if the first controller gets
probed first, it will request its own reset line and will subsequently
request the same reset line again (temporarily) to perform the reset.
This used to work fine before the above-mentioned commit, but now
triggers the new WARN.
Work around this by making sure we reuse the controller's reset if the
controller happens to be the first controller.
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three EHCI controllers on Tegra SoCs, each with its own reset
line. However, the first controller contains a set of UTMI configuration
registers that are shared with its siblings. These registers will only
be reset as part of the first controller's reset. For proper operation
it must be ensured that the UTMI configuration registers are reset
before any of the EHCI controllers are enabled, irrespective of the
probe order.
Commit a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to
broken USB") introduced code that ensures the first controller is always
reset before setting up any of the controllers, and is never again reset
afterwards.
This code, however, grabs the wrong reset. Each EHCI controller has two
reset controls attached: 1) the USB controller reset and 2) the UTMI
pads reset (really the first controller's reset). In order to reset the
UTMI pads registers the code must grab the second reset, but instead it
grabbing the first.
Fixes: a47cc24cd1 ("USB: EHCI: tegra: Fix probe order issue leading to broken USB")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ed_schedule begins with marking the ED as "operational",
the ED may be left in such state even if scheduling actually
fails.
This allows future submission attempts to smuggle this ED to the
hardware behind the scheduler's back and without linking it to
the ohci->eds_in_use list.
The former causes bandwidth saturation and data loss on isoc
endpoints, the latter crashes the kernel when attempt is made
to unlink such ED from this list.
Fix ed_schedule to update ED state only on successful return.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I got one of these cards for testing uas with, it seems that with streams
it dma-s all over the place, corrupting memory. On my first tests it
managed to dma over the BIOS of the motherboard somehow and completely
bricked it.
Tests on another motherboard show that it does work with streams disabled.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several people have reported that UBSAN doesn't like the pointer
arithmetic in ehci_hub_control():
u32 __iomem *status_reg = &ehci->regs->port_status[
(wIndex & 0xff) - 1];
u32 __iomem *hostpc_reg = &ehci->regs->hostpc[(wIndex & 0xff) - 1];
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains.
According to the C standard, pointer computations leading to locations
outside the bounds of an array object (other than 1 position past the
end) are undefined. In this case, the compiler would be justified in
concluding the wIndex can never be 0 and then optimizing away the
tests for !wIndex that occur later in the subroutine. (Although,
since ehci->regs->port_status and ehci->regs->hostpc are both 0-length
arrays and are thus GCC extensions to the C standard, it's not clear
what the compiler is really allowed to do.)
At any rate, we can avoid all these difficulties, at the cost of
making the code slightly longer, by not decrementing the index when it
is equal to 0. The runtime effect is minimal, and anyway
ehci_hub_control() is not on a hot path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Martin_MOKREJÅ <mmokrejs@gmail.com>
Reported-by: "Navin P.S" <navinp1912@gmail.com>
CC: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman