reduce size by 8 bytes from 1160 to 1152 allowing it to fit in 1 fewer
cachelines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Explanation taken from the comment of ata_slave_link_init().
In libata, a port contains links and a link contains devices. There
is single host link but if a PMP is attached to it, there can be
multiple fan-out links. On SATA, there's usually a single device
connected to a link but PATA and SATA controllers emulating TF based
interface can have two - master and slave.
However, there are a few controllers which don't fit into this
abstraction too well - SATA controllers which emulate TF interface
with both master and slave devices but also have separate SCR
register sets for each device. These controllers need separate links
for physical link handling (e.g. onlineness, link speed) but should
be treated like a traditional M/S controller for everything else
(e.g. command issue, softreset).
slave_link is libata's way of handling this class of controllers
without impacting core layer too much. For anything other than
physical link handling, the default host link is used for both master
and slave. For physical link handling, separate @ap->slave_link is
used. All dirty details are implemented inside libata core layer.
From LLD's POV, the only difference is that prereset, hardreset and
postreset are called once more for the slave link, so the reset
sequence looks like the following.
prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
softreset(M) -> postreset(M) -> postreset(S)
Note that softreset is called only for the master. Softreset resets
both M/S by definition, so SRST on master should handle both (the
standard method will work just fine).
As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.
* ata_is_host_link() updated so that slave_link is considered as host
link too.
* iterator extended to iterate over the slave_link when using the
underbarred version.
* force param handling updated such that devno 16 is mapped to the
slave link/device.
* ata_link_on/offline() updated to return the combined result from
master and slave link. ata_phys_link_on/offline() are the direct
versions.
* EH autopsy and report are performed separately for master slave
links. Reset is udpated to implement the above described reset
sequence.
Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.
After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
relevant bits
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Enclosure Management support to libata and ahci.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong. This patch
implements command type based stepped timeouts. Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.
ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much. After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.
IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.
This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back. However, this 5 second delay is superflous or excessive
in many cases. For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.
This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.
As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.
While at it, convert explicit rounding up division to DIV_ROUND_UP().
This change speeds up EH in many cases w/o sacrificing robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing. As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs. So, durations are in msecs and
deadlines are in jiffies. ata_deadline() is added to compute deadline
from a start time and duration in msecs.
While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device. This makes the device completely ignored by
libata.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up. This is
no longer the case. One timeout will make all following accesses fail
immediately.
In rare cases both marvell and SIMG PMPs need almost a second. Bump
it to 3s.
While at it, rename it to SATA_PMP_RW_TIMEOUT. It's not specific to
SCR access.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the kernel-provided clamp_val() macro.
FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants. clamp_val will not cast to short anymore.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This behavior differs across multiple controllers, so we cannot use
common logic for all controllers.
Revert back to the basic common behavior, and specific drivers will
be updated from here to take into account the unusual Status return
values.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Put the big stuff at the end, to prepare for upcoming changes (and
also hopefully achieve nicer packing of remaining members).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set. PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts. This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link. While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.
This change simplifies LLDs and helps making PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Most of PMP support code is already in libata-pmp.c. All that are in
libata-core.c are sata_pmp_port_ops and EXPORTs. Move them to
libata-pmp.c. Also, collect PMP related prototypes and declarations
in header files and move them right above of SFF stuff.
This change is to make PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF support is completely separated out from the core layer,
it can be made optional. Add CONFIG_ATA_SFF and let SFF drivers
depend on it. If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled. This saves good
number of bytes for small systems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers. Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_qc_complete_multiple() took @finish_qc and called it on every qc
before completing it. This was to give opportunity to update TF cache
before ata_qc_complete() tries to fill result_tf. Now that result TF
is a separate operation, this is no longer necessary.
Update sata_sil24, which was the only user of this mechanism, such
that it implements its own ops->qc_fill_rtf() and drop @finish_qc from
ata_qc_complete_multiple().
Signed-off-by: Tejun Heo <htejun@gmail.com>
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.
ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.
ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes. As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset. This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART. However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.
This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs. As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SError used to be cleared in ->postreset. This has small hotplug race
condition. If a device is plugged in after reset is complete but
postreset hasn't run yet, its hotplug event gets lost when SError is
cleared. This patch makes sata_link_resume() clear SError. This
kills the race condition and makes a lot of sense as some PMP and host
PHYs don't work properly without SError cleared.
This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as
they become identical to ata_std counterparts. It also simplifies
sata_pmp_hardreset() and ahci_vt8251_hardreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset(). sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.
ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.
piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific. Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready. Both are
optional. The former is out parameter for link onlineness after
reset. The latter is used to wait for link readiness after hardreset.
Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset(). This doesn't really cause any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready(). ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness. This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.
This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().
ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready(). Functionality remains the same.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Previously, post-softreset readiness is waited as follows.
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
If not, continue to #3.
3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
on devmask using ata_sff_wait_ready().
And for post-hardreset readiness,
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. sata_sff_hardreset waits for device readiness using
ata_sff_wait_ready().
This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().
ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.
ata_sff_wait_after_reset() is updated to perform the following steps.
1. waits for 150ms.
2. waits for dev0 readiness using ata_sff_wait_ready(). Note that
this is done regardless of devmask, as ata_sff_wait_ready() handles
0xff status correctly, this preserves the original behavior except
that it may wait longer after softreset if link is online but
status is 0xff. This behavior change is very unlikely to cause any
actual difference and is intended. It brings softreset behavior to
that of hardreset.
3. waits for dev1 readiness just the same way ata_bus_post_reset() did.
Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets. As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.
This change makes reset implementation simpler and more consistent.
While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap. This is to make them consistent with other
reset helpers and ease core changes.
pata_scc is updated accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.
ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().
This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma
now specifies postreset to ata_sff_postreset() explicitly. sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them. ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version. Waiting for device readiness is the only SFF specific part.
ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset(). This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.
This change reflects real world situation. There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that. Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers. Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.
This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Currently whether a command should be retried after failure is
determined inside ata_eh_finish(). Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy(). This makes things clearer and helps
extending retry determination logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers. Move it out of
CONFIG_PCI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Move SFF related functions from libata-core.c to libata-sff.c.
ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
ata_interrupt(), ata_std_ports()
* Make ata_pio_queue_task() global as it's now called from
libata-sff.c.
* Move SFF related stuff in include/linux/libata.h and
drivers/ata/libata.h into one place. While at it, move timing
constants into the global enum definition and fortify comments a
bit.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata core layer doesn't care about sht or ->irq_handler. Those are
only of interest to the LLD during initialization. This is confusing
and has caused several drivers to have duplicate unused initializers
for these fields.
Currently only sata_nv uses these fields. Make sata_nv use
->private_data, which is supposed to carry LLD-specific information,
instead and kill ->sht and ->irq_handler. nv_pi_priv structure is
defined and struct literals are used to initialize private_data.
Notational overhead is negligible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.
This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data. In addition, port_info and host don't correspond
to each other 1-to-1. Currently, the first non-NULL
port_info->private_data is used.
This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data. LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.
Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht. Other initialization functions take the same information
as arguments. This causes confusion and duplicate unused entries in
structures.
Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly. All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.
As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.
This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.
This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.
To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.
libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.
After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.
* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.
Signed-off-by: Tejun Heo <htejun@gmail.com>
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.
This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.
All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder. This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.
Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear(). It becomes noop if BMDMA address isn't
initialized. Convert them to use ata_noop_irq_clear().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Over the time, ops in ata_port_operations has become a bit confusing.
Reorganize. SFF/BMDMA ops are separated into separate a group as they
will be taken out of ata_port_operations later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_ehi_schedule_probe() was created to hide details of link-resuming
reset magic. Now that all the softreset workarounds are gone,
scheduling probe is very simple - set probe_mask and request RESET.
Kill ata_ehi_schedule_probe() and open code it. This also increases
consistency as ata_ehi_schedule_probe() couldn't cover individual
device probings so they were open-coded even when the helper existed.
While at it, define ATA_ALL_DEVICES as mask of all possible devices on
a link and always use it when requesting probe on link level for
simplicity and consistency. Setting extra bits in the probe_mask
doesn't hurt anybody.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Some controllers can't reliably record the initial D2H FIS after SATA
link is brought online for whatever reason. Advanced controllers
which don't have traditional TF register based interface often have
this problem as they don't really have the TF registers to update
while the controller and link are being initialized.
SKIP_D2H_BSY works around the problem by skipping the wait for device
readiness before issuing SRST, so for such controllers libata issues
SRST blindly and hopes for the best.
Now that libata defaults to hardreset, this workaround is no longer
necessary. For controllers which have support for hardreset, SRST is
never issued by itself. It is only issued as follow-up SRST for
device classification and PMP initialization, so there's no need to
wait for it from prereset.
Kill ATA_LFLAG_SKIP_D2H_BSY.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ATA_EHI_RESUME_LINK has two functions - promote reset to hardreset if
ATA_LFLAG_HRST_TO_RESUME is set and preventing EH from shortcutting
reset action when probing is requested. The former is gone now and
the latter can easily be achieved by making EH to perform at least one
reset if reset is requested, which also makes more sense than
depending on RESUME_LINK flag.
As ATA_EHI_RESUME_LINK was the only EHI reset modifier, this also
kills reset modifier handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that hardreset is the preferred method of resetting, there's no
need for ATA_LFLAG_HRST_TO_RESUME flag. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
When both soft and hard resets are available, libata preferred
softreset till now. The logic behind it was to be softer to devices;
however, this doesn't really help much. Rationales for the change:
* BIOS may freeze lock certain things during boot and softreset can't
unlock those. This by itself is okay but during operation PHY event
or other error conditions can trigger hardreset and the device may
end up with different configuration.
For example, after a hardreset, previously unlockable HPA can be
unlocked resulting in different device size and thus revalidation
failure. Similar condition can occur during or after resume.
* Certain ATAPI devices require hardreset to recover after certain
error conditions. On PATA, this is done by issuing the DEVICE RESET
command. On SATA, COMRESET has equivalent effect. The problem is
that DEVICE RESET needs its own execution protocol.
For SFF controllers with bare TF access, it can be easily
implemented but more advanced controllers (e.g. ahci and sata_sil24)
require specialized implementations. Simply using hardreset solves
the problem nicely.
* COMRESET initialization sequence is the norm in SATA land and many
SATA devices don't work properly if only SRST is used. For example,
some PMPs behave this way and libata works around by always issuing
hardreset if the host supports PMP.
Like the above example, libata has developed a number of mechanisms
aiming to promote softreset to hardreset if softreset is not going
to work. This approach is time consuming and error prone.
Also, note that, dependingon how you read the specs, it could be
argued that PMP fan-out ports require COMRESET to start operation.
In fact, all the PMPs on the market except one don't work properly
if COMRESET is not issued to fan-out ports after PMP reset.
* COMRESET is an integral part of SATA connection and any working
device should be able to handle COMRESET properly. After all, it's
the way to signal hardreset during reboot. This is the most used
and recommended (at least by the ahci spec) method of resetting
devices.
So, this patch makes libata prefer hardreset over softreset by making
the following changes.
* Rename ATA_EH_RESET_MASK to ATA_EH_RESET and use it whereever
ATA_EH_{SOFT|HARD}RESET used to be used. ATA_EH_{SOFT|HARD}RESET is
now only used to tell prereset whether soft or hard reset will be
issued.
* Strip out now unneeded promote-to-hardreset logics from
ata_eh_reset(), ata_std_prereset(), sata_pmp_std_prereset() and
other places.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SAT passthrus don't really fit into ATAPI_MISC class. SAT passthru
commands always transfer multiple of 512 bytes and variable length
response is not allowed. This patch creates a separate category -
ATAPI_PASS_THRU - for these.
This fixes HSM violation on "hdparm -I".
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Uninline atapi_cmd_type(). It doesn't really have to be inline and
more case will be added which need to access unexported libata
variable.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
EH actions are ATA_EH_* not ATA_EHI_*. Rename ATA_EHI_LPM to
ATA_EH_LPM.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.
That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).
So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.
This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.
Original patch is from Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Avoids lots of these, also is more readable.
include/linux/libata.h:1210:13: warning: potentially expensive pointer subtraction
Change the subtraction to addition on the other side of the comparison.
Thanks to Christer Weinigel for the suggestion.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
that provided by the block layer
ATA requires that all DMA transfers begin and end on word boundaries.
Because of this, a large amount of machinery grew up in ide to adjust
scatterlists on this basis. However, as of 2.5, the block layer has a
dma_alignment variable which ensures both the beginning and length of a
DMA transfer are aligned on the dma_alignment boundary. Although the
block layer does adjust the beginning of the transfer to ensure this
happens, it doesn't actually adjust the length, it merely makes sure
that space is allocated for transfers beyond the declared length. The
upshot of this is that scatterlists may be padded to any size between
the actual length and the length adjusted to the dma_alignment safely
knowing that memory is allocated in this region.
Right at the moment, SCSI takes the default dma_aligment which is on a
512 byte boundary. Note that this aligment only applies to transfers
coming in from user space. However, since all kernel allocations are
automatically aligned on a minimum of 32 byte boundaries, it is safe to
adjust them in this manner as well.
tj: * Adjusting sg after padding is done in block layer. Make libata
set queue alignment correctly for ATAPI devices and drop broken
sg mangling from ata_sg_setup().
* Use request->raw_data_len for ATAPI transfer chunk size.
* Killed qc->raw_nbytes.
* Separated out killing qc->n_iter.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
qc->n_iter was used for libata's own sg walking before sg chaining
replaced it. During conversion, the field and its usage in sata_fsl
were left behind. Kill the filed and update sata_fsl.
tj: This was part of James's libata-use-block-layer-padding patch.
Separated out by me.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Factor out ata_pci_activate_sff_host() from ata_pci_one(). This does
about the same thing as ata_host_activate() but needs to be separate
because SFF controllers use different and multiple IRQs in legacy
mode.
This will be used to make SFF LLD initialization more flexible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port_queue_task() served a single user: ata_pio_task()
Rename to ata_pio_queue_task() and un-export it, as nobody outside of
libata-core.c uses it.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qc->nbytes didn't use to include extra buffers setup by libata core
layer and my be odd. This patch makes qc->nbytes include any extra
buffers setup by libata core layer and guaranteed to be aligned on 4
byte boundary.
This value is to be used to program the host controller. As this
represents the actual length of buffer available to the controller and
the controller must be able to deal with short transfers for ATAPI
commands which can transfer variable length, this shouldn't break any
controllers while making problems like rounding-down and controllers
choking up on odd transfer bytes much less likely.
The unmodified value is stored in new field qc->raw_nbytes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata used private sg iterator to handle padding sg. Now that sg can
be chained, padding can be handled using standard sg ops. Convert to
chained sg.
* s/qc->__sg/qc->sg/
* s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg
entry. There need to be two extra sg entries. The renaming is also
for future addition of other extra sg entries.
* Padding setup is moved into ata_sg_setup_extra() which is organized
in a way that future addition of other extra sg entries is easy.
* qc->orig_n_elem is unused and removed.
* qc->n_elem now contains the number of sg entries that LLDs should
map. qc->mapped_n_elem is added to carry the original number of
mapped sgs for unmapping.
* The last sg of the original sg list is used to chain to extra sg
list. The original last sg is pointed to by qc->last_sg and the
content is stored in qc->saved_last_sg. It's restored during
ata_sg_clean().
* All sg walking code has been updated. Unnecessary assertions and
checks for conditions the core layer already guarantees are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With atapi_request_sense() converted to use sg, there's no user of
non-sg interface. Kill non-sg interface.
* ATA_QCFLAG_SINGLE and ATA_QCFLAG_SG are removed. ATA_QCFLAG_DMAMAP
is used instead. (this way no LLD change is necessary)
* qc->buf_virt is removed.
* ata_sg_init_one() and ata_sg_setup_one() are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on how many bytes are transferred as a unit, PIO data
transfer may consume more bytes than requested. Knowing how much
data is consumed is necessary to determine how much is left for
draining. This patch update ->data_xfer such that it returns the
number of consumed bytes.
While at it, it also makes the following changes.
* s/adev/dev/
* use READ/WRITE constants for rw indication
* misc clean ups
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ATAPI command types - ATAPI_READ, WRITE, RW_BUF, READ_CD and MISC,
and implement atapi_cmd_type() which takes SCSI opcode and returns to
which class the opcode belongs. This will be used later to improve
ATAPI handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask() and
while at it relocate the function below ata_acpi_gtm_xfermask().
New ata_acpi_cbl_80wire() implementation takes @gtm, in both pata_via
and pata_amd, use the initial GTM value. Both are trying to peek
initial BIOS configuration, so using initial caching value makes
sense. This fixes ACPI part of cable detection in pata_amd which
previously always returned 0 because configuring PIO0 during reset
clears DMA configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata-acpi is using separate timing tables for transfer modes
although libata-core has the complete ata_timing table. Implement
ata_timing_cycle2mode() to look for matching mode given transfer type
and cycle duration and use it in libata-acpi and pata_acpi to replace
private timing tables.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Finding out matching transfer mode from ACPI GTM values is useful for
other purposes too. Separate out the function and timing tables from
pata_acpi::pacpi_discover_modes().
Other than checking shared-configuration bit after doing
ata_acpi_gtm() in pacpi_discover_modes() which should be safe, this
patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_CBL_PATA_UNK indicates that the cable type can't be determined
from the host side and might be either 80c or 40c. libata applies
drive or other generic limit in this case. However, there are
controllers where both host and drive side detections are
misimplemented and the driver has to rely solely on private method -
peeking BIOS or ACPI configuration or using some other private
mechanism.
This patch adds ATA_CBL_PATA_IGN which tells libata to ignore the
cable type completely and just let the LLD determine the transfer mode
via host transfer mode masks and ->mode_filter().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff says xfer_mask is unsigned long not unsigned int. Convert all
xfermask fields and handling functions to deal with unsigned longs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_id_to_dma_mode() isn't quite generic. The function is basically
privately implemented ata_id_xfermask() combined with hardcoded mode
printing and configuration which are specific to ata_generic.
Kill the function and open code it in generic_set_mode() using generic
xfermode handling functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s/ATA_BITS_(PIO|MWDMA|UDMA)/ATA_NR_\1_MODES/g
* Consistently use 0xff to indicate invalid transfer mode (0x00 is
valid for PIO_SLOW).
* Make ata_xfer_mode2mask() return proper mode mask instead of just
the highest bit.
* Sort ata_timing table in increasing xfermode order and update
ata_timing_find_mode() accordingly.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Export the following xfermode related functions.
* ata_pack_xfermask()
* ata_unpack_xfermask()
* ata_xfer_mask2mode()
* ata_xfer_mode2mask()
* ata_xfer_mode2shift()
* ata_mode_string()
* ata_id_xfermask()
* ata_timing_find_mode()
These functions will be used later by LLD updates. While at it,
change unsigned short @speed to u8 @xfer_mode in
ata_timing_find_mode() for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.
This will be used to improve speed down logic.
Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up EH speed down implementation.
* is_io boolean variable is replaced eflags. is_io is ATA_EFLAG_IS_IO.
* Error categories now have names.
* Better comments.
* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()
* Use local variable @link to cache @dev->link in ata_eh_speed_down()
These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Area for DFLAGs which are cleared on INIT is full. Extend it by 8
bits.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With ATAPI transfer chunk size properly programmed, libata PIO HSM
should be able to handle full spurious data chunks. Also, it's a good
idea to suppress trailing data warning for misc ATAPI commands as
there can be many of them per command - for example, if the chunk size
is 16 and the drive tries to transfer 510 bytes, there can be 31
trailing data messages.
This patch makes the following updates to libata ATAPI PIO HSM
implementation.
* Make it drain full spurious chunks.
* Suppress trailing data warning message for misc commands.
* Put limit on how many bytes can be drained.
* If odd, round up consumed bytes and the number of bytes to be
drained. This gets the number of bytes to drain right for drivers
which do 16bit PIO.
This patch is partial backport of improve-ATAPI-data-xfer patchset
pending for #upstream.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain implementations, _GTF evaluation depends on preceding _STM
and both can be pretty picky about the configuration. Using _GTM
result cached during controller initialization satisfies the most
neurotic _STM implementation. However, libata evaluates _GTF after
reset during device configuration and the hardware state can be
different from what _GTF expects and can cause evaluation failure.
This patch adds dev->gtf_cache and updates ata_dev_get_GTF() such that
it uses the cached value if available. Cache is cleared with a call
to ata_acpi_clear_gtf().
Because for SATA ACPI nodes _GTF must be evaluated after _SDD which
can't be done till IDENTIFY is complete, _GTF caching from
ata_acpi_on_resume() is used only for IDE ACPI nodes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
_GTM fetches currently configured transfer mode while _STM configures
controller according to _GTM parameter and prepares transfer mode
configuration TFs for _GTF. In many cases _GTM and _STM
implementations are quite brittle and can't cope with configuration
changed by libata.
libata does not depend on ATA ACPI to configure devices. The only
reason libata performs _GTM and _STM are to make _GTF evaluation
succeed and libata also doesn't care about how _GTF TFs configure
transfer mode. It overrides that configuration anyway, so from
libata's POV, it doesn't matter what value is feeded to _STM as long
as evaluation succeeds for _STM and following _GTF.
This patch adds dev->__acpi_init_gtm and store initial _GTM values on
host initialization before modified by reset and mode configuration.
If the field is valid, ata_acpi_init_gtm() returns pointer to the
saved _GTM structure; otherwise, NULL.
This saved value is used for _STM during resume and peek at
BIOS/firmware programmed initial timing for later use. The accessor
is there to make building w/o ACPI easy as dev->__acpi_init doesn't
exist if ACPI is not enabled.
On driver detach, the initial BIOS configuration is restored by
executing _STM with the initial _GTM values such that the next driver
can also use the initial BIOS configured values.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make prink helpers format @lv together rather than prepending to the
format string as constant.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* No internal function uses const ata_port. Drop const from @ap.
* Make ata_acpi_stm() copy @stm before using it and change @stm to
const.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
One or two ancient drives predated the cable spec and didn't sent the
valid bits for the field. I had hoped to leave this out of libata as a
piece of historical annoyance but a recent CD drive shows the same bug so
we have to import support for it.
Same concept as Bartlomiej's changes old IDE except that as we have
centralised blacklists we can avoid keeping another private table of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_QCFLAG_QUIET which indicates that there's no need to
report if the command fails with AC_ERR_DEV and set it for passthrough
commands.
Combined with previous changes, this now makes device errors for all
direct commands reported directly to the issuer without going through
EH actions and reporting.
Note that EH is still invoked after non-IO device errors to determine
the nature of the error and resume command execution (some controller
requires special care after error to continue). It just performs
default maintenance after error, examines what's going on, realizes
that it's none of its business and reports the command failure without
logging any error messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Short term, this works around a bug introduced by early sg-chaining
work.
Long term, removing this function eliminates a branch from a hot
path loop in each scatter/gather table build. Also, as this code
demonstrates, we don't need to _track_ the end of the s/g list, as
long as we mark it in some way. And doing so programatically is nice.
So its a useful cleanup, regardless of its short term effects.
Based conceptually on a quick patch by Jens Axboe.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts libata to using the sg helpers for looking up sg
elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* remove pointless pci_dev_to_dev() wrapper. Just directly reference
the embedded struct device like everyone else does.
* pata_cs5520: delete cs5520_remove_one(), it was a duplicate of
ata_pci_remove_one()
* linux/libata.h: don't bother including linux/pci.h, we don't need it.
Simply declare 'struct pci_dev' and assume interested parties will
include the header, as they should be doing anyway.
* linux/libata.h: consolidate all CONFIG_PCI declarations into a
single location in the header.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PMP registers used to be accessed with dedicated accessors ->pmp_read
and ->pmp_write. During reset, those callbacks are called with the
port frozen so they should be able to run without depending on
interrupt delivery. To achieve this, they were implemented polling.
However, as resetting the host port makes the PMP to isolate fan-out
ports until SError.X is cleared, resetting fan-out ports while port is
frozen doesn't buy much additional safety.
This patch updates libata PMP support such that PMP registers are
accessed using regular ata_exec_internal() mechanism and kills
->pmp_read/write() callbacks. The following changes are made.
* PMP access helpers - sata_pmp_read_init_tf(), sata_pmp_read_val(),
sata_pmp_write_init_tf() are folded into sata_pmp_read/write() which
are now standalone PMP register access functions.
* sata_pmp_read/write() returns err_mask instead of rc. This is
consistent with other functions which issue internal commands and
allows more detailed error reporting.
* ahci interrupt handler is modified to ignore BAD_PMP and
spurious/illegal completion IRQs while reset is in progress. These
conditions are expected during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_PFLAG_RESETTING. This flag is set while reset is in
progress. It's set before prereset is called and cleared after reset
fails or postreset is finished.
This flag itself doesn't have any function. It will be used by LLDs
to tell whether reset is in progress if it needs to behave differently
during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Talk to the dark side our driver has to, yes. Much misleading is the
data. Store it in a structure we do so that it may be parsed.
Signed-off-by: Alan Cox <alan@redhat.com>
--
Whats small, old and shouts phrases out of order across mountains ?
Yodla..
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is useful when debugging, handling problem systems, or for
distributions just to get the system installed so it can be sorted
out later.
This is a bit smarter than the old IDE one and lets you do
libata.dma=0 Disable all PATA DMA like old IDE
libata.dma=1 Disk DMA only
libata.dma=2 ATAPI DMA only
libata.dma=4 CF DMA only
(or combinations thereof - 0,1,3 being the useful ones I suspect)
(I've split CF as it seems to be a seperate case of pain and suffering
different to the others and caused by assorted PIO wired adapters etc)
Signed-off-by: Alan Cox <alan@redhat.com>
[edited to work on SATA too, changing name from 'pata_dma' to 'dma']
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement Port Multiplier support. To support PMP, a LLDD has to
supply ops->pmp_read() and pmp_write(). If non-null, ->pmp_attach and
->pmp_detach are called on PMP attach and detach, respectively.
->pmp_read/write() can be called while the port is frozen, so they
must be implemented by polling. This patch supplies several helpers
to ease ->pmp_read/write() implementation.
Also, irq_handler and error_handler must be PMP aware. Most of PMP
aware EH can be done by calling ata_pmp_do_eh() with appropriate
methods. PMP EH uses separate set of reset methods and this patch
implements standard prereset, hardreset and postreset methods.
This patch only implements PMP support. The next patch will integrate
PMP into the reset of libata and thus enable PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Restore the support for handling drives that report one sector too many
(ie SCSI not ATA style). This worked before the HPA update but was
removed in that process.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AN serves multiple purposes. For ATAPI, it's used for media change
notification. For PMP, for downstream PHY status change notification.
Implement sata_async_notification() which demultiplexes AN.
To avoid unnecessary port events, ATAPI AN is not enabled if PMP is
attached but SNTF is not available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some pseudo devices fail PM commands unnecessarily aborting system
suspend. Implement ATA_HORKAGE_SKIP_PM which makes libata skip PM
commands for these devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_LFLAG_DISABLED. The flag indicates the link is disabled
due to EH recovery failure. While a link is disabled, no EH action is
taken on the link and suspend/resume become noop too.
This will be used by PMP links to manage failed links.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some PMP links are connected to internal pseudo devices which may come
and go depending on situation. There's no reason to try hard to
recover them. ATA_LFLAG_NO_RETRY tells EH to not retry if the device
attached to the link fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some links on some PMPs locks up on SRST and/or report incorrect
device signature. Implement ATA_LFLAG_NO_SRST, ASSUME_ATA and
ASSUME_SEMB to handle these quirky links. NO_SRST makes EH avoid
SRST. ASSUME_ATA and SEMB forces class code to ATA and SEMB_UNSUP
respectively. Note that SEMB isn't currently supported yet so the
_UNSUP variant is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ap->nr_active_links (the number of links with active qcs),
ap->excl_link (pointer to link which can be used by ->qc_defer and is
cleared when a qc with ATA_QCFLAG_CLEAR_EXCL completes), and
ata_link_active().
These can be used by ->qc_defer() to implement proper command
exclusion. This set of helpers seem enough for both sil24 (ATAPI
exclusion needed) and cmd-switching PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently. This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.
If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link. If ATA_DEFER_PORT, until a qc completes
on any link. The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.
ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and
sata_sil24 are converted to use ata_std_qc_defer().
ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.
IMHO, this shouldn't cause any noticeable performance issues as
* for most cases deferring occurs rarely (except for NCQ-aware
cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
completes which usually is a very long time cpu-wise.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add PMP related constants, fields and ops. Also, update
ata_class_enabled/disabled() such that PMP classes are considered.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument. @present indicates whether the device seems present during
reset. It's the result of TF access during softreset and link
onlineness during hardreset. @present will be used to improve
diagnostic failure handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In anticipation of more features, increase number of config flags
allowed, and move the init flags.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Hugh Dickens <hugh@veritas.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
EH is sometimes repeated without any error or action. For example,
this happens when probing IDENTIFY fails because of a phantom device.
In these cases, all the repeated EH does is making sure there is no
unhandled error or pending action and return. This repeation is
necessary to avoid losing any event which occurred while EH was in
progress.
Unfortunately, this dry run causes annonying "EH pending after
completion" message. This patch moves the repeat reporting into
ata_eh_report() such that it's more compact and skipped on dry runs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikep@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Combined from two Alan Cox patches:
1) libata: ACPI checks for 80wire cable
We can use the ACPI mode information with several drivers as a hint to
cable type. If the ACPI mode set by the BIOS is faster than UDMA33 then
we know the BIOS thinks there are 80wire cables. If it doesn't set such a
mode or it has no ACPI method then we get no further information and can
rely on existing approaches
Introduce the function headers needed. Null it out for non ACPI boxes
Signed-off-by: Alan Cox <alan@redhat.com>
2) libata: ACPI checks for 80wire cable
Provide actual methods for checking if the ACPI support thinks the cable
is 80wire, or doesn't know
Signed-off-by: Alan Cox <alan@redhat.com>
Combined into a single changeset and
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tell the compiler that [__]ata_ehi_push_desc() functions take printf
style format string and arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_wait_idle() identified controller by printing out the address of
the Status register. This is bogus because 1. it's iomapped address
2. some controllers don't have Status register and don't initialize
the field. Use ata_port_printk() instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change. This will be done via the scsi device.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.
printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links. If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some drives choke on READ_NATIVE_MAX_ADDRESS[_EXT]. Implement
ATA_HORKAGE_BROKEN_HPA and apply it to affected drives.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI implementations in several TOSHIBA laptops are weird and burn cpu
cycles for tens of seconds while trying to suspend if the PCI device
for the ATA controller is disabled when the ACPI suspend is called.
This patch uses DMI to match those machines and bypass device disable
on those machines during suspend. As the device needs to be put into
enabled state on resume without affecting PCI enable count, matching
resume callback uses __pci_reenable_device().
This bug is reported in bugzilla bug 7780.
http://bugzilla.kernel.org/show_bug.cgi?id=7780
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In most cases, when EH is scheduled, all in-flight commands are
aborted causing EH to kick in immediately. However, in some cases
(especially with PMP), it's unclear which commands are affected by the
error condition and although aborting all in-flight commands work, it
isn't optimal and may cause unnecessary disruption. On the other
hand, waiting for in-flight commands to drain themselves can take up
to 30seconds.
This patch implements EH fast drain to handle such situations. It
gives in-flight commands some time to finish up but doesn't wait for
too long. After EH is scheduled, fast drain timer is started and if
no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight
commands are aborted. If any completion occurred in the interval, the
port is given another interval to finish up itself.
Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough
for finishing up most commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
__ata_ehi_hotplugged() now has no users. Regorganize
ata_ehi_hotplugged() such that a new function ata_ehi_schedule_probe()
deals with scheduling probing. ata_ehi_hotplugged() calls it and
additionally marks hotplug specific flags. ata_ehi_schedule_probe()
will be used laster.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_down_spd_limit() first reads the current SPD from SStatus and
limit the speed to the lower one of one below the current limit or one
below the current SPD in SStatus. SPD may not be accessible or valid
when SPD down is requested making sata_down_spd_limit() fail when it's
most needed.
This patch makes the current SPD cached after each successful reset
and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached
value is valid, so sata_down_spd_limit() is now guaranteed to lower
the speed limit if lower speed is available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ->scr_read/write callbacks to return error code to better
indicate failure. This will help handling of SCR_NOTIFICATION.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When an NCQ command fails, all commands in flight are aborted and the
offending one is reported using log page 10h. Depending on controller
characteristics and LLD implementation, all commands may appear as
having a device error due to shared TF status making it hard to
determine what's actually going on.
This patch adds AC_ERR_NCQ, marks the command reported by log page 10h
with it and print extra "<F>" after the error report for the command
to help distinguishing the offending command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @is_cmd to ata_tf_to_fis(). This controls bit 7 of the second
byte which tells the device whether this H2D FIS is for a command or
not. This cleans up ahci a bit and will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds a new field, lldd_task, to ata_queued_cmd so that libata
users such as libsas can associate some data with a qc. The particular
ambition with this patch is to associate a sas_task with a qc; that way,
if libata decides to timeout a command, we can come back (in
sas_ata_post_internal) and abort the sas task.
One question remains: Is it necessary to reset the phy on error, or will
the libata error handler take care of it? (Assuming that one is written,
of course.) This patch, as it is today, works well enough to clean
things up when an ATA device probe attempt fails halfway through the probe,
though I'm not sure this is always the right thing to do.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Horkage handling had the following problems.
* dev->horkage was positioned after ATA_DEVICE_CLEAR_OFFSET, so it was
cleared before the device is configured. This broke
HORKAGE_DIAGNOSTIC.
* Some used dev->horkage while others called ata_device_blacklisted()
directly. This was at best confusing.
This patch moves dev->horkage right after dev->flags and set the field
according to the blacklist during device configuration. All users
test against dev->horkage. ata_device_blacklisted() now has only one
user, make it static. While at it, rename it to ata_dev_blacklisted()
for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Richard Kennedy