Both qc_prep functions deal only with BMDMA PRD setup and PIO only SFF
drivers don't need them. Rename to ata_bmdma_[dumb_]qc_prep() and
relocate.
All usages are renamed except for pdc_adma and sata_qstor. Those two
drivers are not BMDMA drivers and don't need to call BMDMA qc_prep
functions. Calls to ata_sff_qc_prep() in the two drivers are removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some of error handling logic in ata_sff_error_handler() and all of
ata_sff_post_internal_cmd() are for BMDMA. Create
ata_bmdma_error_handler() and ata_bmdma_post_internal_cmd() and move
BMDMA part into those.
While at it, change DMA protocol check to ata_is_dma(), fix
post_internal_cmd to call ap->ops->bmdma_stop instead of directly
calling ata_bmdma_stop() and open code hardreset selection so that
ata_std_error_handler() doesn't have to know about sff hardreset.
As these two functions are BMDMA specific, there's no reason to check
for bmdma_addr before calling bmdma methods if the protocol of the
failed command is DMA. sata_mv and pata_mpc52xx now don't need to set
.post_internal_cmd to ATA_OP_NULL and pata_icside and sata_qstor don't
need to set it to their bmdma_stop routines.
ata_sff_post_internal_cmd() becomes noop and is removed.
This fixes p3 described in clean-up-BMDMA-initialization patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
port_task is tightly bound to the standard SFF PIO HSM implementation.
Using it for any other purpose would be error-prone and there's no
such user and if some drivers need such feature, it would be much
better off using its own. Move it inside CONFIG_ATA_SFF and rename it
to sff_pio_task.
The only function which is exposed to the core layer is
ata_sff_flush_pio_task() which is renamed from ata_port_flush_task()
and now also takes care of resetting hsm_task_state to HSM_ST_IDLE,
which is possible as it's now specific to PIO HSM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->[last_]ctl are specific to SFF controllers. Put them inside
CONFIG_ATA_SFF and move initialization into ata_sff_port_init().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When BMDMA initialization failed or BMDMA was not available for
whatever reason, bmdma_addr was left at zero and used as an indication
that BMDMA shouldn't be used. This leads to the following problems.
p1. For BMDMA drivers which don't use traditional BMDMA register,
ata_bmdma_mode_filter() incorrectly inhibits DMA modes. Those
drivers either have to inherit from ata_sff_port_ops or clear
->mode_filter explicitly.
p2. non-BMDMA drivers call into BMDMA PRD table allocation. It
doesn't actually allocate PRD table if bmdma_addr is not
initialized but is still confusing.
p3. For BMDMA drivers which don't use traditional BMDMA register, some
methods might not be invoked as expected (e.g. bmdma_stop from
ata_sff_post_internal_cmd()).
p4. SFF drivers w/ custom DMA interface implement noop BMDMA ops
worrying libata core might call into one of them.
These problems are caused by the muddy line between SFF and BMDMA and
the assumption that all BMDMA controllers initialize bmdma_addr.
This patch fixes p1 and p2 by removing the bmdma_addr assumption and
moving prd allocation to BMDMA port start. Later patches will fix the
remaining issues.
This patch improves BMDMA initialization such that
* When BMDMA register initialization fails, falls back to PIO instead
of failing. ata_pci_bmdma_init() never fails now.
* When ata_pci_bmdma_init() falls back to PIO, it clears
ap->mwdma_mask and udma_mask instead of depending on
ata_bmdma_mode_filter(). This makes ata_bmdma_mode_filter()
unnecessary thus resolving p1.
* ata_port_start() which actually is BMDMA specific is moved to
ata_bmdma_port_start(). ata_port_start() and ata_sff_port_start()
are killed.
* ata_sff_port_start32() is moved and renamed to
ata_bmdma_port_start32().
Drivers which no longer call into PRD table allocation are...
pdc_adma, sata_inic162x, sata_qstor, sata_sx4, pata_cmd640 and all
drivers which inherit from ata_sff_port_ops.
pata_icside sets ->port_start to ATA_OP_NULL as it doesn't need PRD
but is a BMDMA controller and doesn't have custom port_start like
other such controllers.
Note that with the previous patch which makes all and only BMDMA
drivers inherit from ata_bmdma_port_ops, this change doesn't break
drivers which need PRD table.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Reorder functions such that SFF and BMDMA functions are grouped.
While at it, s/BMDMA/SFF in a few comments where it actually meant
SFF.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_FLAG_DISABLED is only used by drivers which don't use
->error_handler framework and is largely broken. Its only meaningful
function is to make irq handlers skip processing if the flag is set,
which is largely useless and even harmful as it makes those ports more
likely to cause IRQ storms.
Kill ATA_FLAG_DISABLED and makes the callers disable attached devices
instead. ata_port_probe() and ata_port_disable() which manipulate the
flag are also killed.
This simplifies condition check in IRQ handlers. While updating IRQ
handlers, remove ap NULL check as libata guarantees consecutive port
allocation (unoccupied ports are initialized with dummies) and
long-obsolete ATA_QCFLAG_ACTIVE check (checked by ata_qc_from_tag()).
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now, with the introduction of the sff_set_devctl() method, we can
use it in sff_irq_on() method too -- that way its implementations
in 'pata_bf54x' and 'pata_scc' become virtually identical to
ata_sff_irq_on(). The sff_irq_on() method now becomes quite
superfluous, and the only reason not to remove it completely is
the existence of the 'pata_octeon_cf' driver which implements it
as an empty function. Just make the method optional then, with
ata_sff_irq_on() becoming generic taskfile-bound function, still
global for the 'pata_bf54x' driver to be able to call it from its
thaw() and postreset() methods.
While at it, make the sff_irq_on() method and ata_sff_irq_on() return
'void' as the result is always ignored anyway.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The set of libata's taskfile access methods is clearly incomplete as
it lacks a method to write to the device control register -- which
forces drivers like 'pata_bf54x' and 'pata_scc' to implement more
"high level" (and more weighty) methods like freeze() and postreset().
So, introduce the optional sff_set_devctl() method which the drivers
only have to implement if the standard iowrite8() can't be used (just
like the existing sff_check_altstatus() method) and make use of it
in the freeze() and postreset() method implementations (I could also
have used it in softreset() method but it also reads other taskfile
registers without using tf_read() making that quite pointless);
this makes freeze() method implementations in the 'pata_bf54x' and
'pata_scc' methods virtually identical to ata_sff_freeze(), so we
can get rid of them completely.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There are some SATA devices which take relatively long to get out of
0xff status after reset. In libata, this timeout is determined by
ATA_TMOUT_FF_WAIT. Quantum GoVault is the worst requring about 2s for
reliable detection. However, because 2s 0xff timeout can introduce
rather long spurious delay during boot, libata has been compromising
at the next longest timeout of 800ms for HHD424020F7SV00 iVDR drive.
Now that parallel scan is in place for common drivers, libata can
afford 2s 0xff timeout. Use 2s 0xff timeout if parallel scan is
enabled.
Please note that the chance of spurious wait is pretty slim w/ working
SCR access so this will only affect SATA controllers w/o SCR access
which isn't too common these days.
Please read the following thread for more information on the GoVault
drive.
http://thread.gmane.org/gmane.linux.ide/14545/focus=14663
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some BIOSes don't configure HPA during boot but do so while resuming.
This causes harddrives to shrink during resume making libata detach
and reattach them. This can be worked around by unlocking HPA if old
size equals native size.
Add ATA_DFLAG_UNLOCK_HPA so that HPA unlocking can be controlled
per-device and update ata_dev_revalidate() such that it sets
ATA_DFLAG_UNLOCK_HPA and fails with -EIO when the above condition is
detected.
This patch fixes the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=15396
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Oleksandr Yermolenko <yaa.bta@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem. Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.
This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received. If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port. Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.
This patch also implements ->sff_irq_check() for ata_piix. Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
* piix_base_ops dropped as suggested by Sergei.
* Spurious IRQ detection doesn't kick in anymore if polling qc is in
progress. This provides less protection but some controllers have
possible data corruption issues if the wrong register is accessed
while a command is in progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Hans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Interestingly, when SIDPR is used in ata_piix, writes to DET in
SControl sometimes get ignored leading to detection failure. Update
sata_link_resume() such that it reads back SControl after clearing DET
and retry if it's not clear.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: fengxiangjun <fengxiangjun@neusoft.com>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
This patch modifies scsi_host_template->change_queue_depth so that
it takes an argument indicating why it is being called. This will be
used so that if a LLD needs to do some extra processing when
handling queue fulls or later ramp ups, it can do so.
This is a simple port of the drivers setting a change_queue_depth
callback. In the patch I just have these LLDs adjust the queue depth
if the user was requesting it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[Vasu.Dev: v2
Also converted pmcraid_change_queue_depth and then verified
all modules compile using "make allmodconfig" for any new build
warnings on X86_64.
Updated original description after combing two original
patches from Mike to make this patch git bisectable.]
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
[jejb: fixed up 53c700]
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.
However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.
This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination. Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode. This was reported in the following bugzilla bug.
http://bugzilla.kernel.org/show_bug.cgi?id=14543
This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ->gtf_filter to ata_device and set it to ata_acpi_gtf_filter when
initializing ata_link. This is to allow quirks which apply different
gtf filters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently libata-acpi can only filter DIPM among SATA feature enables
via _GTF. This patch adds the capability to filter out FPDMA non-zero
offset, in-order guarantee and auto-activation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We're about to add more SATA_* and ATA_ACPI_FILTER_* constants.
Reformat them in preparation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was a hack to give userland shutdown tools time to drop manual
spindown. All popular distros updated quite some time ago and the due
is well passed. Drop it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Hopefully results in fewer on-the-wire FIS's and no breakage. We'll see!
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards. In the following
thread, the problem can be reliably reproduced after resuming from
STR. The BIOS turns on HPA during boot but forgets to do it during
resume.
http://thread.gmane.org/gmane.linux.kernel/858310
This patch updates libata revalidation such that it considers native
n_sectors. If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one. This should be fairly safe
while nicely working around the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christof Warlich <christof@warlich.name>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PIONEER DVD-RW DVRTD08 times out SETXFER if no media is present. The
device is SATA and simply skipping SETXFER works around the problem.
Implement ATA_HORKAGE_NOSETXFER and apply it to the device.
Reported by Moritz Rigler in the following thread.
http://thread.gmane.org/gmane.linux.ide/36790
and by Lars in bko#9540.
Updated to whine and ignore NOSETXFER if PATA component is detected as
suggested by Alan Cox.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Moritz Rigler <linux-ide@momail.e4ward.com>
Reported-by: Lars <lars21ce@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The legacy old IDE ioctl API for this is a bit primitive so we try
and map stuff sensibly onto it.
- Set PIO over DMA devices to report 32bit
- Add ability to change the PIO32 settings if the controller permits it
- Add that functionality into the sff drivers
- Add that functionality into the VLB legacy driver
- Turn on the 32bit PIO on the ninja32 and add support there
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On a timeout call a device specific handler early in the recovery so that
we can complete and process successful commands which timed out due to IRQ
loss or the like rather more elegantly.
[Revised to exclude the timeout handling on a few devices that inherit from
SFF but are not SFF enough to use the default timeout handler]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If the device is signalling that there is data to drain after an error we
should read the bytes out and throw them away. Without this some devices
and controllers get wedged and don't recover.
Based on earlier work by Mark Lord
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ap->sector_buf is used as DMA target and should at least be aligned on
cacheline. This caused problems on some embedded machines.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata passes the returned value of dma_map_sg() to
dma_unmap_sg(),which is the misuse of dma_unmap_sg().
DMA-mapping.txt says:
To unmap a scatterlist, just call:
pci_unmap_sg(pdev, sglist, nents, direction);
Again, make sure DMA activity has already finished.
PLEASE NOTE: The 'nents' argument to the pci_unmap_sg call must be
the _same_ one you passed into the pci_map_sg call,
it should _NOT_ be the 'count' value _returned_ from the
pci_map_sg call.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This fixes problems during resume with drives that take longer than 1s to
be ready. The ATA-6 spec appears to allow 5 seconds for a drive to be
ready.
On one affected system, this patch changes "PM: resume devices took..."
message from 17 seconds to 4 seconds, and gets rid of a lot of ugly
timeout/error messages.
Without this patch, the libata code moves on after 1s, tries to send a
soft reset (which the drive doesn't see because it isn't ready) which also
times out, then an IDENTIFY command is sent to the drive which times out,
and finally the error handler will try to send another hard reset which
will finally get things working.
Signed-off-by: Stuart Hayes <stuart_hayes@dell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
3Gbps is often much more prone to transmission failures. It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them. Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.
This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.
Please take a look at the following bz for related reports.
http://bugzilla.kernel.org/show_bug.cgi?id=9913
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table. I add a
new column for dmack_hold time. The values were obtained from the
Compact Flash specification Rev 4.1.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
for SAS drivers.
Caught by Ke Wei (and team?) at Marvell.
Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.
Drivers that do not set this flag get their ports scanned in
the "original" sequence.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_port_detach() first made sure EH saw ATA_PFLAG_UNLOADING and then
assumed EH context belongs to it and performed detach operation
itself. However, UNLOADING doesn't disable all of EH and this could
lead to problems including triggering WARN_ON()'s in EH path.
This patch makes port detach behave more like other EH actions such
that ata_port_detach() requests EH to detach and waits for completion.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some recent Seagate harddrives have firmware bug which causes FLUSH
CACHE to timeout under certain circumstances if NCQ is being used.
This can be worked around by disabling NCQ and fixed by updating the
firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these
devices.
The wiki page has been updated to contain information on this issue.
http://ata.wiki.kernel.org/index.php/Known_issues
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch reverts the following three commits which convert libata to
use block layer tagging.
43a49cbdf3e013e13bf62fca5ccf97
Although using block layer tagging is the right direction, due to the
tight coupling among tag number, data structure allocation and
hardware command slot allocation, libata doesn't work correctly with
the current conversion.
The biggest problem is guaranteeing that tag 0 is always used for
non-NCQ commands. Due to the way blk-tag is implemented and how SCSI
starts and finishes requests, such guarantee can't be made. I'm not
sure whether this would actually break any low level driver but it
doesn't look like a good idea to break such assumption given the
frailty of ATA controllers.
So, for the time being, keep using the old dumb in-libata qc
allocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axobe <jens.axboe@oracle.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
libata always uses PIO for ATAPI commands when the number of bytes to
transfer isn't multiple of 16 but quantum DAT72 chokes on odd bytes
PIO transfers. Implement a horkage to skip the mod16 check and apply
it to the quantum device.
This is reported by John Clark in the following thread.
http://thread.gmane.org/gmane.linux.ide/34748
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: John Clark <clarkjc@runbox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata currently imposes a UDMA5 max transfer rate and 200 sector max
transfer size for SATA devices that sit behind a pata-sata bridge. Lots
of devices have known good bridges that don't need this limit applied.
The MTRON SSD disks are such devices. Transfer rates are increased by
20-30% with the restriction removed.
So add a "blacklist" entry for the MTRON devices, with a flag indicating
that the bridge is known good.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used to control the behavior
of EH. As only the master link is visible outside EH, these flags are
set only for the master link although they should also apply to the
slave link, which causes spurious EH messages during probe and
suspend/resume.
This patch transfers those two flags to slave ehc.i before performing
slave autopsy and reporting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
reduce size by 8 bytes from 1160 to 1152 allowing it to fit in 1 fewer
cachelines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop
expected to hit the floor). In fact, the whole port stops processing
commands until the timeout has expired in order to avoid any resets due
to failed commands on another device.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Explanation taken from the comment of ata_slave_link_init().
In libata, a port contains links and a link contains devices. There
is single host link but if a PMP is attached to it, there can be
multiple fan-out links. On SATA, there's usually a single device
connected to a link but PATA and SATA controllers emulating TF based
interface can have two - master and slave.
However, there are a few controllers which don't fit into this
abstraction too well - SATA controllers which emulate TF interface
with both master and slave devices but also have separate SCR
register sets for each device. These controllers need separate links
for physical link handling (e.g. onlineness, link speed) but should
be treated like a traditional M/S controller for everything else
(e.g. command issue, softreset).
slave_link is libata's way of handling this class of controllers
without impacting core layer too much. For anything other than
physical link handling, the default host link is used for both master
and slave. For physical link handling, separate @ap->slave_link is
used. All dirty details are implemented inside libata core layer.
From LLD's POV, the only difference is that prereset, hardreset and
postreset are called once more for the slave link, so the reset
sequence looks like the following.
prereset(M) -> prereset(S) -> hardreset(M) -> hardreset(S) ->
softreset(M) -> postreset(M) -> postreset(S)
Note that softreset is called only for the master. Softreset resets
both M/S by definition, so SRST on master should handle both (the
standard method will work just fine).
As slave_link excludes PMP support and only code paths which deal with
the attributes of physical link are affected, all the changes are
localized to libata.h, libata-core.c and libata-eh.c.
* ata_is_host_link() updated so that slave_link is considered as host
link too.
* iterator extended to iterate over the slave_link when using the
underbarred version.
* force param handling updated such that devno 16 is mapped to the
slave link/device.
* ata_link_on/offline() updated to return the combined result from
master and slave link. ata_phys_link_on/offline() are the direct
versions.
* EH autopsy and report are performed separately for master slave
links. Reset is udpated to implement the above described reset
sequence.
Except for reset update, most changes are minor, many of them just
modifying dev->link to ata_dev_phys_link(dev) or using phys online
test instead.
After this update, LLDs can take full advantage of per-dev SCR
registers by simply turning on slave link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement __ata_port_next_link() and reimplement
__ata_port_for_each_link() and ata_port_for_each_link() using it.
This removes relatively large inlined code and makes iteration easier
to extend.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Logically, SCR access ops should take @link; however, there was no
compelling reason to convert all SCR access ops when adding @link
abstraction as there's one-to-one mapping between a port and a non-PMP
link. However, that assumption won't hold anymore with the scheduled
addition of slave link.
Make SCR access ops per-link.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Dave Müller sent a diff for the pata_oldpiix that highlighted a problem
where a lot of the ATA drivers assume dma_mode == 0 means "no DMA" while
the core code uses 0xFF.
This turns out to have other consequences such as code doing >= XFER_UDMA_0
also catching 0xFF as UDMAlots. Fortunately it doesn't generally affect
set_dma_mode, although some drivers call back into their own set mode code
from other points.
Having been through the drivers I've added helpers for using_udma/using_mwdma
dma_enabled so that people don't open code ranges that may change (eg if UDMA8
appears somewhere)
Thanks to David for the initial bits
[and added fix for pata_oldpiix from and signed-off-by Dave Mueller
<dave.mueller@gmx.ch> -jg]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Save SControl during probing and restore it on detach. This prevents
adjustments made by libata drivers to seep into the next driver which
gets attached (be it a libata one or not).
It's not clear whether SControl also needs to be restored on suspend.
The next system to have control (ACPI or kexec'd kernel) would
probably like to see the original SControl value but there's no
guarantee that a link is gonna keep working after SControl is adjusted
without a reset and adding a reset and modified recovery cycle soley
for this is an overkill. For now, do it only for detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Implement force params nohrst, nosrst and norst. This is to work
around reset related problems and ease debugging.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Add support for the RDC 1010 variant
- Rework the core library to have a read_id method. This allows the hacky
bits of it821x to go and prepares us for pata_hd
- Switch from WARN to BUG in ata_id_string as it will reboot if you get
it wrong so WARN won't be seen
- Allow the issue of command 0xFC on the 821x. This is needed to query
rebuild status.
- Tidy up printk formatting
- Do more ident rewriting on RAID volumes to handle firmware provided
ident data which is rather wonky
- Report the firmware revision and device layout in RAID mode
- Don't try and disable raid on the 8211 or RDC - they don't have the
relevant bits
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add Enclosure Management support to libata and ahci.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA_TMOUT_INTERNAL which was 30secs were used for all internal
commands which is way too long when something goes wrong. This patch
implements command type based stepped timeouts. Different command
types can use different timeouts and each command type can use
different timeout values after timeouts.
ie. the initial timeout is set to a value which should cover most of
the cases but not too long so that run away cases don't delay things
too much. After the first try times out, the second try can use
longer timeout and if that one times out too, it can go for full 30sec
timeout.
IDENTIFYs use 5s - 10s - 30s timeout and all other commands use 5s -
10s timeouts.
This patch significantly cuts down the needed time to handle failure
cases while still allowing libata to work with nut job devices through
retries.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
EH retries were delayed by 5 seconds to ensure that resets don't occur
back-to-back. However, this 5 second delay is superflous or excessive
in many cases. For example, after IDENTIFY times out, there's no
reason to wait five more seconds before retrying.
This patch adds ehc->last_reset timestamp and record the timestamp for
the last reset trial or success and uses it to space resets by
ATA_EH_RESET_COOL_DOWN which is 5 secs and removes unconditional 5 sec
sleeps.
As this change makes inter-try waits often shorter and they're
redundant in nature, this patch also removes the "retrying..."
messages.
While at it, convert explicit rounding up division to DIV_ROUND_UP().
This change speeds up EH in many cases w/o sacrificing robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing. As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs. So, durations are in msecs and
deadlines are in jiffies. ata_deadline() is added to compute deadline
from a start time and duration in msecs.
While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it
Add
ata_sff_irq_status - encapsulates the IRQ check logic
This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that
ata_sff_sync - ensure writes hit the device
Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.
- ata_sff_pause - 400nS delay
Ensure the command hit the device and delay 400nS
- ata_sff_dma_pause
Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)
The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I was hoping ATA_HORKAGE_NODMA | ATA_HORKAGE_SKIP_PM could keep it
happy but no even this doesn't work under certain configurations and
it's not like we can do anything useful with the cofig device anyway.
Replace ATA_HORKAGE_SKIP_PM with ATA_HORKAGE_DISABLE and use it for
the config device. This makes the device completely ignored by
libata.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This timeout was set low because previously PMP register access was
done via polling and register access timeouts could stack up. This is
no longer the case. One timeout will make all following accesses fail
immediately.
In rare cases both marvell and SIMG PMPs need almost a second. Bump
it to 3s.
While at it, rename it to SATA_PMP_RW_TIMEOUT. It's not specific to
SCR access.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use the kernel-provided clamp_val() macro.
FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants. clamp_val will not cast to short anymore.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This behavior differs across multiple controllers, so we cannot use
common logic for all controllers.
Revert back to the basic common behavior, and specific drivers will
be updated from here to take into account the unusual Status return
values.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Export ata_eh_analyze_ncq_error() for subsequent use by sata_mv,
as suggested by Tejun.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet. It looks like they use 0xff if device
presence is detected but connection isn't established. 0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.
This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions. This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.
This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.
Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Put the big stuff at the end, to prepare for upcoming changes (and
also hopefully achieve nicer packing of remaining members).
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make PMP support optional by adding CONFIG_SATA_PMP and leaving out
libata-pmp.c if it isn't set. PMP helpers return constant values if
PMP support is not enabled and PMP declarations alias non-PMP
counterparts. This makes the compiler to leave out PMP related part
out and LLDs to use non-PMP counterparts automatically.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement helpers to test whether PMP is supported, attached and
determine pmp number to use when issuing SRST to a link. While at it,
move ata_is_host_link() so that it's together with the two new PMP
helpers.
This change simplifies LLDs and helps making PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Most of PMP support code is already in libata-pmp.c. All that are in
libata-core.c are sata_pmp_port_ops and EXPORTs. Move them to
libata-pmp.c. Also, collect PMP related prototypes and declarations
in header files and move them right above of SFF stuff.
This change is to make PMP support optional.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF support is completely separated out from the core layer,
it can be made optional. Add CONFIG_ATA_SFF and let SFF drivers
depend on it. If CONFIG_ATA_SFF isn't set, all codes in libata-sff.c
and data structures for SFF support are disabled. This saves good
number of bytes for small systems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Now that SFF assumptions are separated out from non-SFF reset
sequence, port_ops->sff_dev_select() is no longer necessary for
non-SFF controllers. Kill ata_noop_dev_select() and ->sff_dev_select
initialization from base and other non-SFF port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_qc_complete_multiple() took @finish_qc and called it on every qc
before completing it. This was to give opportunity to update TF cache
before ata_qc_complete() tries to fill result_tf. Now that result TF
is a separate operation, this is no longer necessary.
Update sata_sil24, which was the only user of this mechanism, such
that it implements its own ops->qc_fill_rtf() and drop @finish_qc from
ata_qc_complete_multiple().
Signed-off-by: Tejun Heo <htejun@gmail.com>
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf. This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.
ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.
ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes. As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.
Signed-off-by: Tejun Heo <htejun@gmail.com>
If PMP fan-out reset fails and SCR isn't accessible, PMP should be
reset. This used to be tested by sata_pmp_std_hardreset() and
communicated to EH by -ERESTART. However, this logic is generic and
doesn't really have much to do with specific hardreset implementation.
This patch moves SCR access failure detection logic to ata_eh_reset()
where it belongs. As this makes sata_pmp_std_hardreset() identical to
sata_std_hardreset(), the function is killed and replaced with the
standard method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SError used to be cleared in ->postreset. This has small hotplug race
condition. If a device is plugged in after reset is complete but
postreset hasn't run yet, its hotplug event gets lost when SError is
cleared. This patch makes sata_link_resume() clear SError. This
kills the race condition and makes a lot of sense as some PMP and host
PHYs don't work properly without SError cleared.
This change makes sata_pmp_std_{pre|post}_reset()'s unnecessary as
they become identical to ata_std counterparts. It also simplifies
sata_pmp_hardreset() and ahci_vt8251_hardreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset(). sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.
ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.
piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific. Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready. Both are
optional. The former is out parameter for link onlineness after
reset. The latter is used to wait for link readiness after hardreset.
Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset(). This doesn't really cause any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready(). ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness. This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.
This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().
ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready(). Functionality remains the same.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Previously, post-softreset readiness is waited as follows.
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
If not, continue to #3.
3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
on devmask using ata_sff_wait_ready().
And for post-hardreset readiness,
1. ata_sff_wait_after_reset() waits for 150ms and then for
ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.
2. sata_sff_hardreset waits for device readiness using
ata_sff_wait_ready().
This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().
ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready(). If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.
ata_sff_wait_after_reset() is updated to perform the following steps.
1. waits for 150ms.
2. waits for dev0 readiness using ata_sff_wait_ready(). Note that
this is done regardless of devmask, as ata_sff_wait_ready() handles
0xff status correctly, this preserves the original behavior except
that it may wait longer after softreset if link is online but
status is 0xff. This behavior change is very unlikely to cause any
actual difference and is intended. It brings softreset behavior to
that of hardreset.
3. waits for dev1 readiness just the same way ata_bus_post_reset() did.
Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets. As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.
This change makes reset implementation simpler and more consistent.
While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap. This is to make them consistent with other
reset helpers and ease core changes.
pata_scc is updated accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.
ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().
This change affects pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma
now specifies postreset to ata_sff_postreset() explicitly. sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them. ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version. Waiting for device readiness is the only SFF specific part.
ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset(). This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24. pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.
This change reflects real world situation. There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that. Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.
Signed-off-by: Tejun Heo <htejun@gmail.com>
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers. Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.
This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Add sff_ prefix to SFF specific port ops.
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames ops and doesn't introduce any
behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...
* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.
* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.
* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.
* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.
* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.
The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()
This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Currently whether a command should be retried after failure is
determined inside ata_eh_finish(). Add ATA_QCFLAG_RETRY and move the
logic into ata_eh_autopsy(). This makes things clearer and helps
extending retry determination logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers. Move it out of
CONFIG_PCI.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Move SFF related functions from libata-core.c to libata-sff.c.
ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
ata_interrupt(), ata_std_ports()
* Make ata_pio_queue_task() global as it's now called from
libata-sff.c.
* Move SFF related stuff in include/linux/libata.h and
drivers/ata/libata.h into one place. While at it, move timing
constants into the global enum definition and fortify comments a
bit.
This patch strictly moves stuff around and as such doesn't cause any
functional difference.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently reset methods are not specified directly in the
ata_port_operations table. If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods. It's done this way for two reasons.
First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.
Second, as ->error_handler uses those reset methods, it can get
confusing. ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.
Now that ops table uses inheritance, the first problem doesn't exist
anymore. The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks. In fact, there currently is no driver which actually
modifies error handling behavior. Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH. I don't think making ops layering strict has
any noticeable benefit.
This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops. Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.
* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
aren't accessible. sata_promise doesn't need to use separate
error_handlers for PATA and SATA anymore.
* softreset is broken for sata_inic162x and sata_sx4. As libata now
always prefers hardreset, this doesn't really matter but the ops are
forced to NULL using ATA_OP_NULL for documentation purpose.
* pata_hpt374 needs to use different prereset for the first and second
PCI functions. This used to be done by branching from
hpt374_error_handler(). The proper way to do this is to use
separate ops and port_info tables for each function. Converted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Tejun Heo