This patch replaces hardcoded 2's with the NET_IP_ALIGN constant or
TG3_RAW_IP_ALIGN where appropriate. Some platforms can redefine the
NET_IP_ALIGN definition to zero if unaligned DMA transfers cost more
than the IP header alignment gains. This patch represents a
performance improvement when using the 5701 on these platforms.
The copy path can be avoided.
TG3_RAW_IP_ALIGN is used in cases where we always want to align the
IP header on dword boundaries.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to network device ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version to 3.95.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines support for the 5785 device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refines the phylib support in the tg3 driver. The patch does
the following things :
* Rename tg3_mdio_config() to tg3_mdio_config_5785(). The 5785 will be
the only device that will use it so the name might as well reflect
that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
MAC <=> PHY interface.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows WOL to be enabled for Broadcom phys under phylib
control. The only exception is the AC131, which has a completely
different register set.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver. The patch was understandably conservative, so this patch
elaborates on that work.
The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL. The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.
The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled. The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, phylib reports appear with a eth%d prefix. Move the line
after register_netdev() and place it alongside the other informative
messages. Update nearby informative messages accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With older versions of the NVRAM format, the driver may mistakenly
determine that APE is enabled. Make sure this doesn't happen by
restricting the ENABLE_APE check to devices known to have more
recent NVRAM image formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reclaims the TG3_FLG3_5761_5784_AX_FIXES flag. It only
used twice in non-fast paths. This patch also consolidates some other
places where specific 5784 AX chip revisions can be generalized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the __tg3_set_mac_addr() function earlier in the file
listing, to avoid a function prototype, and calls the function to
restore the LAA after a driver unload chip reset. With this code in
place, the administrator can wake the machine using the LAA.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH firmware runs on the APE side of the chip, but it requires a few MAC
to be programmed correctly.
When WOL is enabled and management firmware is disabled, incoming
packets are evaluated and discarded at the chip's rule processor.
When management firmware is enabled, the hardware must be informed that
there are agents further up the stack that still use the incoming
frames. Normally management firmware will configure the MAC correctly
on its own, but there can be cases where the setting could get clobbered
by the driver. The first hunk of this patch preserves this setting.
The second hunk of this patch wipes out the driver present signature of
the APE memory space. By doing so, the DASH firmware can assume
driver absent behavior.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the existing APE register mapping code with a call
to pci_ioremap_bar(). The code that maps the main device register space
did not undergo a similar change because the information derived from
the pci_resource_start() and pci_resource_len() is still used to
populate the (optional) mem_start and mem_end netdevice members.
Replace hardcoded constants where appropriate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 5761S chip variants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces mdiobus_alloc() and mdiobus_free(), and
makes all mdio bus drivers use these functions to allocate their
struct mii_bus'es dynamically.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch updates the version number to 3.94.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool stats are 64-bits in length. net_device_stats members are
unsigned long types. When gathering information for
a get_ethtool_stats call, the driver will call a driver-private,
inlined get_stat64() function, which returns an unsigned long value.
This call will inadvertently mask off the upper 32-bits of a stat on
32-bit machines.
This patch defines a new get_estat() inline function and modifies the
ESTAT_ADD() macro to use it.
Signed-off-by: Stefan Buehler <stbuehler@web.de>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The git commit 7c5026aa9b ("tg3: Add
link state reporting to UMP firmware") introduced code that waits for
previous firmware events to be serviced before attempting to submit a
new event. Unfortunately that patch contained a bug that cause the
driver to wait 2.5 seconds, rather than 2.5 milliseconds as intended.
This patch fixes that bug.
This bug revealed that not all firmware versions service driver events
though. Since we do not know which versions of the firmware do and don't
service these events, the driver needs some way to minimize the effects
of the delay. This patch solves the problem by recording a jiffies
timestamp when it submits an event to the hardware. If the jiffies
counter shows that 2.5 milliseconds have already passed, a wait is not
needed and the driver can proceed to submit a new event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENABLE_ASF flag is set when DASH is enabled on the NIC, but DASH
does not run on the RX CPU. Instead it runs on the APE.
Consequently, the driver does not need to send "driver alive" updates
to the RX CPU when the APE is present.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's DASH (Desktop and mobile Architecture for System Hardware)
implementation requires that the driver preserve particular register
settings. If the driver does not preserve them, communication with
the DASH firmware will be lost.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, more status bits have been added to the APE status register.
This patch refines the status register check so that the driver can
send more events than it would have otherwise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver resets the chip while the APE is performing a register
access, that register access will never complete and the APE will hang
indefinitely. To prevent this race condition, the driver must acquire
an APE mutex before resetting the chip. The APE will not attempt a
register access until it acquires this lock.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the 'scheduling while atomic' errors introduced by
commit 12dac0756d ("tg3: adapt tg3 to
use reworked PCI PM code").
The first hunk of the patch removes an unnecessary
tg3_set_power_state() call. The chip will already be in the D0 state
either due to a chip reset or through a previous call to
tg3_set_power_state().
The second hunk of the patch moves the tg3_set_power_state() call
outside the critical section guarded by tg3_full_lock() and
tg3_full_unlock() functions. The power state of the device is and
should be outside the lock's domain and all other
tg3_set_power_state() calls support this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the tg3 driver to use the reworked PCI PM and make it use the
exported PCI PM core functions instead of accessing the PCI PM registers
directly by itself.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increments the version to 3.92.1.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 5761 non-e devices, two problems prevent the administrator from
overriding the WOL settings in the device's NVRAM.
The first problem is that GPIO 0 and GPIO 2 have been swapped. This
change prevented the administrator from turning on WOL when it is
disabled in NVRAM. The fix is to add a new path for the 5761 that
swaps the two GPIOs in the code as well.
The second problem is that GPIO 1 could not be toggled by the driver
because the GPIO is shared with the debug UART GPIO. This will prevent
the administrator from being able to turn WOL off if it was enabled in
NVRAM. The fix is to always disable the debug UART after a GRC reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the TG3_FLAG_10_100_ONLY flag was
testing against the wrong flags variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The git commit ef167e2703 entitled
"Fix supporting flowctrl code" introduced a bug that prevents 5714S,
5715S and 5780S devices from falling back to a forced link mode. The
problem is that the added flow control check will always fail if flow
control is set to autoneg and either RX or TX (or both) flow control
is enabled. The driver defaults to setting flow control to autoneg
and advertises both RX and TX flow control.
The fix is to remove the errant check.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increments the version to 3.93.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some options obtained through shared memory.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added the 5785 device ID and ASIC revision to the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the libphy support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces code to register and unregister the tg3 mdio bus
with the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the TG3_FLG3_USE_PHYLIB flag and applies it to
some select places. This work makes later patches a little easier to
read.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch applies cleanups that would otherwise clutter later
patches.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves some functions towards the top of the file to avoid
unnecessary function prototypes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove extraneous semicolons after switch and conditional statements.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be. This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MI clock is not configured correctly on adapters with the CPMU
present. The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions. Consequently, the MI will run slow when the
core's clock has been slowed down.
There is a new 500KHz constant frequency clock available on adapters
with a CPMU. This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.
Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following sparse warning :
drivers/net/tg3.c:4025:3: warning: context imbalance in 'tg3_restart_hw'
- unexpected unlock
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu's commit fb93134dfc, entitled
"[TCP]: Fix size calculation in sk_stream_alloc_pskb", has triggered a
bug in the 5701 where the 5701 DMA engine will corrupt outgoing
packets. This problem only happens when the starting address of the
packet matches a certain range of offsets and only when the 5701 is
placed downstream of a particular Intel bridge.
This patch detects the problematic bridge and if present, readjusts the
starting address of the packet data to a dword aligned boundary.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver stores the PCI resource addresses into 'unsigned long' variable
before calling ioremap_nocache() on them. This warrants kernel oops when the
registers are accessed on PPC 44x platforms which (being 32-bit) have PCI
memory space mapped beyond 4 GB.
The arch/ppc/ kernel has a fixup in ioremap() that creates an illusion that
the PCI memory resource is mapped below 4 GB, but arch/powerpc/ code got rid
of this trick, having instead CONFIG_RESOURCES_64BIT enabled.
[ Bump driver version and release date -DaveM ]
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5784 B step and newer chips require the PHY DSPs to be fine-tuned
based on one-time programmable values stored in the chip. This is
essential to achieve optimal PHY operations especially when using
long cables. We also need to properly handle the 10Mbit RX bit in the
CPMU_CTRL register during PHY reset.
Update version to 3.89.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparc MAC address support should be protected consistently
with CONFIG_SPARC, but there was a stray CONFIG_SPARC64
case.
Bump driver version and release date.
Reported by Andrew Morton.
Signed-off-by: David S. Miller <davem@davemloft.net>
When asked to blink LEDs the tg3 driver behaves when using:
ethtool -p ethX
The default value for data is zero, and other drivers interpret this
as blink forever (or at least a really long time). The tg3 driver
interprets this as blink once. All drivers should have the same
behaviour.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.87.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does three things. It modifies tg3_setup_flow_control() to
use the administrator requested flow control settings if
autonegotiation is turned off. It slightly modifies the
tg3_setup_fiber_mii_phy() function to account for this new use case.
And finally, it does the same for tg3_setup_copper_phy().
The copper modifications are more than a small multi-line change. The
new code makes an attempt to avoid a link renegotiation if the link is
active at half duplex and the only difference between the current
advertised settings and requested advertised settings is the
flow control advertisements.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the software autoneg code to use the administrator
specified flow control parameters. Since the autonegotiation code uses
alternative flow control enumerations, the 1000-BaseX utility functions
are used and code was added to convert the definitions to and from the
alternate enumerations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the 5704S hardware autoneg code to use the
administrator specified flow control parameters. Since the 5704S uses
device specific flow control enumerations, the 1000-BaseX utility
functions are used and code was added to convert the definitions to and
from the proprietary enumerations.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces magic values with preprocessor definitions for
the sg_dig_ctrl and sg_dig_status registers. This is preparatory work
for the next patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two functions designed to convert abstract TX & RX
flow control parameters to 1000-BaseT and 1000-BaseX autonegotiation
advertisements. Code that uses standard definitions which statically
advertises TX & RX flow control has been replaced with code that
configures the advertisements based on administrator dictated
preferences.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new utility functions to resolve flow control. One
function resolves flow control based on 1000-BaseT register definitions.
The other resolves flow control based on 1000-Base X register
definitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the TX and RX flow control flags from tg3_flags and
adds two new flow control variables, flowctrl and active_flowctrl.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_nvram_write_block_unbuffered() is reading data from nvram into
allocated buffer before overwriting a part of it with user-supplied
data. Then it feeds the entire page back to nvram. It should be
storing the words it had read as little-endian, not as host-endian.
Note that tg3_set_eeprom() does exactly that for padding the same
data to full words before it gets passed down to tg3_nvram_write_block()
and then to tg3_nvram_write_block_unbuffered().
Moreover, when we get to sending the entire thing back to nvram, we
go through it word-by-word, doing essentially
writel(swab32(le32_to_cpu(word)), ...)
so if we want them to reach the card in host-independent endianness,
we'd better really have all that buffer filled with fixed-endian.
For user-supplied part we obviously do have that (it's an array of
octets memcpy'd in), ditto for padding of user-supplied part to word
boundaries (taken care of in tg3_set_eeprom()). The rest of the
buffer gets filled by tg3_nvram_write_block_unbuffered() and it would
damn better be consistent with that (and with tg3_get_eeprom(), while
we are at it - there we also convert the words read from nvram to
little-endian before returning the buffer to user).
The bug should get triggered on big-endian boxen when set_eeprom is done
for less than entire page. Then the words that should've been unaffected
at all will actually get byteswapped in place in nvram.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed misannotations, introduced a new helper - tg3_nvram_read_le().
It gets __le32 * instead of u32 * and puts there the value converted
to little-endian. A lot of callers of tg3_nvram_read() were doing
that; converted them to tg3_nvram_read_le().
At that point the driver is practically endian-clean; the only remaining
place is an actual bug, AFAICS; will be dealt with in the next patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.86
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the PHY type reported through ethtool for copper
devices from MII to TP. The latter is more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the A1 revision of 5784, 5764, and 5761, and applies all
previous bugfixes. In places where the list of devices gets too long,
the patch uses a new TG3_FLG3_5761_5784_AX_FIXES flag instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous devices hardcoded the PCI Maximum Read Request Size to 4K. To
better comply with the PCI spec, the hardware now defaults the MRRS to
512 bytes. This will yield poor driver performance if left untouched.
This patch increases the MRRS to 4K on driver initialization.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal hardware timers become inaccurate after link events. Clock
frequency switches performed by the CPMU fail to adjust timer
prescalers. The fix is to detect core clock frequency changes during
link events and adjust the timer prescalers accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most 5784 / 5764 LED modes do not work as expected because of a hardware
bug. This patch forces the LED mode to be in MAC LED mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New CPMU devices contend with the GPHY for power management. The GPHY
autopowerdown feature is enabled by default in the PHY and thus needs to
be disabled after every PHY reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the LINK_SPEED mode to the list of CPMU modes that can
cause the loopback tests to fail. These bugs are planned to be fixed in
future revisions of the chip, so the patch qualifies the fixes as such.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The
fix is to run the MAC clock at faster speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle. This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available. When the PHY is powered down, the clock the MAC depends on
is disabled. The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates. The tg3 driver has code to detect this
condition and resets the device during initialization. On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761. However, during this initialization stage, communications
to the APE registers have not yet been set up. The driver then
dereferences a NULL pointer and crashes the machine. The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A reasonably common problem with some devices is that they will
disable MSI generation when the INTX_DISABLE bit is set in the
PCI_COMMAND register.
Quirk this explicitly, guarding the pci_intx() calls in msi.c with
this quirk indication.
The first entries for this quirk are for 5714 and 5780 Tigon3 chips,
and thus we can remove the workaround code from the tg3.c driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the version number to 3.85.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the way the driver works with the PCI command
register. It adjusts the access size from dwords to words. This patch
is done both as a PCI configuration space cleanup and as preparatory
work for PCI error recovery.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch appends the management firmware version to the bootcode
firmware string reported through ethtool.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for upcoming 5723 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IPV6]: Consolidate the ip6_pol_route_(input|output) pair
[TCP]: Make snd_cwnd_cnt 32-bit
[TCP]: Update the /proc/net/tcp documentation
[NETNS]: Don't panic on creating the namespace's loopback
[NEIGH]: Ensure that pneigh_lookup is protected with RTNL
[INET]: kmalloc+memset -> kzalloc in frag_alloc_queue
[ISDN]: Fix compile with CONFIG_ISDN_X25 disabled.
[IPV6]: Replace sk_buff ** with sk_buff * in input handlers
[SELINUX]: Update for netfilter ->hook() arg changes.
[INET]: Consolidate the xxx_put
[INET]: Small cleanup for xxx_put after evictor consolidation
[INET]: Consolidate the xxx_evictor
[INET]: Consolidate the xxx_frag_destroy
[INET]: Consolidate xxx_the secret_rebuild
[INET]: Consolidate the xxx_frag_kill
[INET]: Collect common frag sysctl variables together
[INET]: Collect frag queues management objects together
[INET]: Move common fields from frag_queues in one place.
[TG3]: Fix performance regression on 5705.
[ISDN]: Remove local copy of device name to make sure renames work.
...
This will convert remaining non-obvious or naive calculations of array
sizes to use ARRAY_SIZE() macro.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A performance regression was introduced by the following commit:
commit ee6a99b539
Author: Michael Chan <mchan@broadcom.com>
Date: Wed Jul 18 21:49:10 2007 -0700
[TG3]: Fix msi issue with kexec/kdump.
In making that change, the PCI latency timer and cache line size
registers were not restored after chip reset. On the 5705, the
latency timer gets reset to 0 during chip reset and this causes
very poor performance.
Update version to 3.84.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to read and store sblk->status_tag before checking for more work.
The status tag is later written back to the hardware when enabling
interrupts to acknowledge how much work has been processed. If the
order is reversed, we can end up acknowledging work we haven't
processed.
When we detect tx error, it is more correct to return the rx
work_done so far instead of 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug caused by the recent APE support added for 5761
devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for the list handling in net_rx_action() to be
correct, drivers must follow certain rules as stated by
this comment in net_rx_action():
/* Drivers must not modify the NAPI state if they
* consume the entire weight. In such cases this code
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
A few drivers do not do this because they mix the budget checks
with reading hardware state, resulting in crashes like the one
reported by takano@axe-inc.co.jp.
BNX2 and TG3 are taken care of here, SKY2 fix is from Stephen
Hemminger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update to version 3.83.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables WOL by default if out-of-box WOL is enabled in the
NVRAM.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rest of the miscellaneous code required to support the
5761.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new APE block, present in 5761 chips.
APE stands for Application Processing Engine. The primary function of
the APE is to process manageability traffic, such as ASF.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new 5761-specific NVRAM strapping decode routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I recently noticed that when calling:
# ethtool -s eth0 autoneg on
on a 5722 (though I'm sure it's not specific to that card) that
subsequent checks of the cards status looked like this:
# ethtool eth0
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised auto-negotiation: No <---- This seems odd?!?
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
I noticed that the following commit:
commit 3600d918d8
Author: Michael Chan <mchan@broadcom.com>
Date: Thu Dec 7 00:21:48 2006 -0800
[TG3]: Allow partial speed advertisement.
Honor the advertisement bitmask from ethtool. We used to always
advertise the full capability when autoneg was set to on.
changed things around so that ethtool speed settings were strictly
followed. Unfortunately ethtool doesn't seem to set ADVERTISED_Autoneg
in the advertising field (and maybe it shouldn't have to). I'd vote
that it should be fixed there, but it should also be added here just in
case someone using ethtool ioctls in their own application gets what
they want.
Adding that flag in tg3_set_settings seemed like the most logical place
since the driver works fine on boot. This is just an issue when
re-enabling autonegotiation, so we should probably nip it there.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support for 5784 and 5764 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer products change the way the ASIC revision is obtained. This patch
implements how the driver will extract the revision number.
This patch also adds preliminary CPMU support. CPMU stands for Central
Power Management Unit. The CPMU's role is to put the chip into lower
power states when the operating conditions allow it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer tg3 devices shuffle around the registers in PCI configuration
space. This patch changes the way the driver accesses the PCI
capabilities registers. Hardcoded register locations are replaced with
offsets from pci_find_capability() return values.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed sparse warnings from tg3 driver. The new logic seems fine (I
don't immediately see where we are running over values for any of the
variables that need to be saved).
This patch compiles fine and I'm currently using a tg3 with the patched
driver to post this patch as a basic proof of concept.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI. The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.
We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.
Update version to 3.81.
This problem was discovered by David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joachim Deguara <joachim.deguara@amd.com> reported that tg3 devices
would not resume properly if the device was shutdown before the system
was suspended. In such scenario where the netif_running state is 0,
tg3_suspend() would not save the PCI state and so the memory enable bit
and bus master enable bit would be lost.
We fix this by always saving and restoring the PCI state in
tg3_suspend() and tg3_resume() regardless of netif_running() state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tina Yang <tina.yang@oracle.com> discovered an MSI related problem
when doing kdump. The problem is that the kexec kernel is booted
without going through system reset, and as a result, MSI may already
be enabled when tg3_init_one() is called. tg3_init_one() calls
pci_save_state() which will save the stale MSI state. Later on in
tg3_open(), we call pci_enable_msi() to reconfigure MSI on the chip
before we reset the chip. After chip reset, we call
pci_restore_state() which will put the stale MSI address/data back
onto the chip.
This is no longer a problem in the latest kernel because
pci_restore_state() has been changed to restore MSI state from
internal data structures which will guarantee restoring the proper
MSI state.
But I think we should still fix it. Our save and restore sequence
can still cause very subtle problems down the road. The fix is to
have our own functions save and restore precisely what we need. We
also change it to save and restore state inside tg3_chip_reset() in a
more straight forward way.
Thanks to Tina for helping to test and debug the problem.
[ Bump driver version and release date. -DaveM ]
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool utility function to set or clear IPV6_CSUM feature flag.
Modify tg3.c and bnx2.c to use this function when doing ethtool -K
to change tx checksum.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
This patch adds a missing NVRAM strapping for 5755 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds automatic MDI crossover support when autonegotiation is
turned off. Automatic MDI crossover allows link to be established
without the use of a crossover cable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most pre-5705 devices, multiple link interrupts were being generated
for a single physical link change. The source of the interrupts was
determined to be unnecessary toggling of the MAC link polarity bit.
This patch changes the way the link polarity bit gets configured. Where
possible, code that dynamically configures the bit in response to link
changes has been replaced by code that configures the bit once during
initialization time and then leaves the bit alone.
For correctness, this patch also limits the use of the bit to those
devices where it is defined, namely devices before the 5705. This patch
also corrects the link polarity configurations for 5700 devices when
paired against a bcm5411 phy.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gagan Arneja <gaagaan@gmail.com> pointed out that tg3_reset_task()
could potentially race with another thread calling tg3_full_lock()
such as the ethtool_set_xxx() functions. This may trigger the
BUG_ON() in tg3_irq_quiesce() or cause the irq_sync flag to be out-
of-sync.
I think the easiest way to fix this is to get the tp->lock first
before setting the irq_sync flag. This is safe to do because the
tp->lock is never grabbed by the irq handler. This change will
guarantee that the irq_sync flag updates will be serialized. We also
have to change one spot to call tg3_netif_start() (which clears the
irq_sync flag) before releasing the tp->lock.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The existing model for checksum offload does not correctly handle
devices that can offload IPV4 and IPV6 only. The NETIF_F_HW_CSUM flag
implies device can do any arbitrary protocol.
This patch:
* adds NETIF_F_IPV6_CSUM for those devices
* fixes bnx2 and tg3 devices that need it
* add NETIF_F_IPV6_CSUM to ipv6 output (incl GSO)
* fixes assumptions about NETIF_F_ALL_CSUM in nat
* adjusts bridge union of checksumming computation
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug is caused by code that always set
(TG3_FLAG_USE_MI_INTERRUPT | TG3_FLAG_USE_LINKCHG_REG) on all Dell's
onboard devices. With these 2 flags set, the link status is polled
by tg3_timer() and will only work when the PHY is set up to interrupt
the MAC on link changes. This breaks 5906 because the 5906 PHY does
not support TG3_FLAG_USE_MI_INTERRUPT the same as other PHYs.
For correctness, only Dell's onboard 5701 needs these 2 flags to be
set. This change will fix the 5906 problem and will change other
Dell devices except 5700 and 5701 to use the more efficient
interrupt-driven link changes.
Update version to 3.77.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers had code that did kill_vid, but they weren't doing vlan
filtering. With new API the stub is unneeded unless device sets
NETIF_F_HW_VLAN_FILTER.
Bad habit: I couldn't resist fixing a couple of nearby style things
in acenic, and forcedeth.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
flush_work(wq, work) doesn't need the first parameter, we can use cwq->wq
(this was possible from the very beginnig, I missed this). So we can unify
flush_work_keventd and flush_work.
Also, rename flush_work() to cancel_work_sync() and fix all callers.
Perhaps this is not the best name, but "flush_work" is really bad.
(akpm: this is why the earlier patches bypassed maintainers)
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert tg3 over to flush_work_keventd(). Remove nasty now-unneeded deadlock
avoidance logic.
(akpm: bypassed maintainers, sorry. There are other patches which depend on
this)
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Spurious interrupts are often encountered especially on systems
using the 8259 PIC mode. This is because the I/O write to deassert
the interrupt is posted and won't get to the chip immediately. As
a result, the IRQ may remain asserted after the IRQ handler exits,
causing spurious interrupts.
Flush the interrupt mailbox in non-MSI handlers to de-assert the
IRQ immediately. This seems to be the most straight forward approach
after discussion with Jeff Garzik and David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds workaround to fix performance problems caused by slow
PCIE L1->L0 transitions on ICH8 platforms.
Changed all magic numbers to constants as suggested by Jeff Garzik.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix up the code to always allow MSI on 5714 A2.
Call tg3_find_peer() earlier because we need that information before
we can determine whether we can set TG3_FLAG_SUPPORT_MSI or not.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.
[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL. This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the NVRAM sizing procedure so that the driver can
take advantage of devices with 1:1 NVRAM strapping configurations. This
is useful in cases where the traditional NVRAM sizing method fails. In
the event that the flash size cannot be determined, the largest known
NVRAM size is used. The patch also removes support for 5755 NVRAM
devices that are not supported by Broadcom and adds explicit sizing for
this device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the check for skb->len greater than MTU when doing TSO.
When the destination has a smaller MSS than the source, a TSO packet
may be smaller than the MTU and we still need to process it as a TSO
packet.
2. On 5705A3 devices with TSO enabled, the DMA engine can hang due to a
hardware bug. This patch avoids the hanging condition by reducing the
DMA burst size.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
The only unfortunate bit here is that the name field of struct map_info
is not const, so for now we put a cast on the assignment of it.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The ip_hdrlen() buddy, created to reduce the number of skb->h.th-> uses and to
avoid the longer, open coded equivalent.
Ditched a no-op in bnx2 in the process.
I wonder if we should have a BUG_ON(skb->h.th->doff < 5) in tcp_optlen()...
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common sequence "skb->nh.iph->ihl * 4", removing a good number of open
coded skb->nh.iph uses, now to go after the rest...
Just out of curiosity, here are the idioms found to get the same result:
skb->nh.iph->ihl << 2
skb->nh.iph->ihl<<2
skb->nh.iph->ihl * 4
skb->nh.iph->ihl*4
(skb->nh.iph)->ihl * sizeof(u32)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will crash when the chip has been initialized by EFI before
tg3_init_one(). In this case, the driver will call tg3_chip_reset()
before allocating consistent memory.
The bug is fixed by checking for tp->hw_status before accessing it
during tg3_chip_reset().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On most tg3 chips, the memory enable bit in the PCI command register
gets cleared during chip reset and must be restored before accessing
PCI registers using memory cycles. The chip does not generate
interrupt during chip reset, but the irq handler can still be called
because of irq sharing or irqpoll. Reading a register in the irq
handler can cause a master abort in this scenario and may result in a
crash on some architectures.
Use the TG3_FLAG_CHIP_RESETTING flag to tell the irq handler to exit
without touching any registers. The checking of the flag is in the
"slow" path of the irq handler and will not affect normal performance.
The msi handler is not shared and therefore does not require checking
the flag.
Thanks to Bernhard Walle <bwalle@suse.de> for reporting the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This flag to support multiple PCIX split completions was never used
because of hardware bugs. This will make room for a new flag.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson