Some NXP processors using ChipIdea USB IP have a bug when frame babble is
detected.
Issue description:
In USB camera test, our controller is host in HS mode. In ISOC IN, when
device sends data across the micro frame, it causes the babble in host
controller. This will clear the PE bit. In spec, it also requires to set
the PEC bit and then set the PCI bit. Without the PCI interrupt, the
software does not know the PE is cleared.
This will add a flag CI_HDRC_HAS_PORTSC_PEC_MISSED to some impacted
platform datas. And the ehci host driver will assert PEC by SW when
specific conditions are satisfied.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20230809024432.535160-2-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases, the user may need to tune the rise/fall time of the
high-speed transmitter waveform for USB Certification. This will add
a parameter for this purpose. The value will be fetched from dtb and
finally written to the register.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb38 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@vger.kernel.org>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20230627112126.1882666-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Acked-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230718143027.1064731-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dedicated imx8ulp usb compatible to remove QoS request
since imx8ulp has no such limitation of imx7ulp: DMA will
not work if system enters idle.
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Message-ID: <20230530104007.1294702-2-xu.yang_2@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart from
emitting a warning) and this typically results in resource leaks. To improve
here there is a quest to make the remove callback return void. In the first
step of this quest all drivers are converted to .remove_new() which already
returns void. Eventually after all drivers are converted, .remove_new() is
renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230517230239.187727-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20230310144729.1545857-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As there maybe more APIs of usbmisc for suspend and resume, group
them into imx_usbmisc_suspend/resume. Besides, introduced .power_lost_check
API, so that proper resume operations can be performed in power lost case.
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20221013151442.3262951-6-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err_probe() to simplify handling errors in ci_hdrc_imx_probe()
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220614120522.1469957-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the first call to devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0)
fails with something other than -ENODEV then it leads to an error
pointer dereference. For those errors we should just jump directly to
the error handling.
Fixes: 8253a34bfa ("usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211117074923.GF5237@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When passing 'phys' in the devicetree to describe the USB PHY phandle
(which is the recommended way according to
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt) the
following NULL pointer dereference is observed on i.MX7 and i.MX8MM:
[ 1.489344] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000098
[ 1.498170] Mem abort info:
[ 1.500966] ESR = 0x96000044
[ 1.504030] EC = 0x25: DABT (current EL), IL = 32 bits
[ 1.509356] SET = 0, FnV = 0
[ 1.512416] EA = 0, S1PTW = 0
[ 1.515569] FSC = 0x04: level 0 translation fault
[ 1.520458] Data abort info:
[ 1.523349] ISV = 0, ISS = 0x00000044
[ 1.527196] CM = 0, WnR = 1
[ 1.530176] [0000000000000098] user address but active_mm is swapper
[ 1.536544] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 1.542125] Modules linked in:
[ 1.545190] CPU: 3 PID: 7 Comm: kworker/u8:0 Not tainted 5.14.0-dirty #3
[ 1.551901] Hardware name: Kontron i.MX8MM N801X S (DT)
[ 1.557133] Workqueue: events_unbound deferred_probe_work_func
[ 1.562984] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO BTYPE=--)
[ 1.568998] pc : imx7d_charger_detection+0x3f0/0x510
[ 1.573973] lr : imx7d_charger_detection+0x22c/0x510
This happens because the charger functions check for the phy presence
inside the imx_usbmisc_data structure (data->usb_phy), but the chipidea
core populates the usb_phy passed via 'phys' inside 'struct ci_hdrc'
(ci->usb_phy) instead.
This causes the NULL pointer dereference inside imx7d_charger_detection().
Fix it by also searching for 'phys' in case 'fsl,usbphy' is not found.
Tested on a imx7s-warp board.
Fixes: 746f316b75 ("usb: chipidea: introduce imx7d USB charger detection")
Cc: stable@vger.kernel.org
Reported-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210921113754.767631-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if of_find_device_by_node() succeed, usbmisc_get_init_data() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: ef12da914e ("usb: chipidea: imx: properly check for usbmisc")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201117011430.642589-1-yukuai3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl/R7S0ACgkQSFkpgVDW
cbv/QQf+KhHOZYYzGMZXvyDiFIoE28sfrxyTrZKoDUXIWuAsLegpvY/bw6YJxAZy
bj8z/iAk6NOyQLMH+2ULQoJfc8GX18O05ZOSKg+prcIw5e398TEH0NFrJZV/0dBa
VSk0+pGaRvn6jLfw/lF2EImf4gHLh4EsgDOgWn4ffZL3IRwmGPub2splppmu9N88
1fbrxexc5NORnIpigH0kkftPQkda7slPfo3pMRjpHHb49SDQVw0C2x6FPooQxoaz
c7DWEKfy2E8OcRDCgFdFFLIZNELSlvLHXOk1H8taTXlcVSHHFgos69qzCdOeiRuq
OMHzsRM+M2XEb7LlSPYU0+G/K6SXFQ==
=dV/G
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Below are main changes for v5.11-rc1:
For Chipidea USB2:
- Add tracepoint support for UDC
- Some tiny improvements
For Cadence USB3
- Add some quirks for host mode, and let host work well at more use cases
* SKIP_PHY_INIT
* Disable BEI
* Enable runtime PM default for i.mx platform
- Some tiny improvements
* tag 'usb-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
MAINTAINERS: Add myself as a reviewer for CADENCE USB3 DRD IP DRIVER
usb: chipidea: ci_hdrc_imx: Use of_device_get_match_data()
usb: chipidea: usbmisc_imx: Use of_device_get_match_data()
usb: cdns3: fix NULL pointer dereference on no platform data
usb: chipidea: trace: fix the endian issue
usb: chipidea: add tracepoint support for udc
doc: dt-binding: cdns,usb3: add wakeup-irq
usb: cdns3: imx: enable runtime pm by default
usb: cdns3: add quirk for enable runtime pm by default
usb: cdns3: host: disable BEI support
usb: cdns3: host: add xhci_plat_priv quirk XHCI_SKIP_PHY_INIT
usb: cdns3: host: add .suspend_quirk for xhci-plat.c
usb: cdns3: Rids of duplicate error message
usb: cdns3: Add static to cdns3_gadget_exit function
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
According to the i.MX6UL Errata document:
https://www.nxp.com/docs/en/errata/IMX6ULCE.pdf
ERR007881 also affects i.MX6UL, so pass the
CI_HDRC_DISABLE_DEVICE_STREAMING flag to workaround the issue.
Fixes: 52fe568e5d ("usb: chipidea: imx: add imx6ul usb support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20201207020909.22483-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pinctrl setting may lost during the system suspend
(eg, imx7ulp), it needs to restore them after system resume.
Meanwhile, some platforms may need to set special pinctrl
for power comsumption.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
These two parameters are used to improve USB signal for board level,
in this commit, we read it from the dtb, and write to related register
during the initialization.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If runtime dr_mode is not dual-role, it doesn't need to enable ID
wakeup interrupt.
If runtime dr_mode is host, it doesn't need to enable VBUS
wakeup interrupt.
With these changes, the user will not get the unexpected wakeup
for single role use case. For example, the host-only use case at
Micro-AB port, the controller should not be waken up by only
plug in Micro-AB cable or the Micro-B cable with host.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAl7Mf1oACgkQSFkpgVDW
cbskgggAvRbKPI2Zbw4tHa1JgwkADxg2Q3ewxFLiNIJ7GVLpZeiBn4Dziong6za9
1tB/f4qVyAlVT/zLYrxo9oCMwmGOLJjxigGLqJ2iMtDqcRG++jCdirTMXiI2Fdlh
ZCup49W0IWKmQ7mSLK0TDVbEpYT8YOICiCJumMxhMYuP6bfgFihPjh8NTiz4X7Jr
SUw5rCS7qTRAwDeywIbzWIeCmc4MKaohx4t/XD4Xxz0rPvJrkPgZAaiPh9vJzyMh
2XgFZovLin46QaVbSxxhTUJ7PitCQYzXF+W5vqsdtHkj2u3N3o0MPbSDCKT3oYUb
2zLS7SHzHuKmgFSnxOcLI56gF32uHg==
=YwB9
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Some improvments for ci_hdrc_usb2.c
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
* tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: Enable user-space triggered role-switching
usb: chipidea: udc: add software sg list support
usb: chipidea: usbmisc_imx: using different ops for imx7d and imx7ulp
usb: chipidea: pull down dp for possible charger detection operation
usb: chipidea: introduce imx7d USB charger detection
usb: chipidea: introduce CI_HDRC_CONTROLLER_VBUS_EVENT glue layer use
usb: chipidea: usb2: remove unneeded semicolon
usb: chipidea: allow disabling glue drivers if EMBEDDED
usb: chipidea: usb2: absorb zevio glue driver
usb: chipidea: usb2: make clock optional
usb: chipidea: usb2: fix formatting
usb: chipidea: usb2: constify zynq_pdata
usb: chipidea: core: show the real pointer value for register
usb: chipidea: core: refine the description for this driver
usb: chipidea: udc: fix the kernel doc for udc.h
imx7d (and imx8mm, imx8mn) uses Samsung PHY and USB generic PHY driver.
The USB generic PHY driver is impossible to have a charger detection
for every user, so we implement USB charger detection routine at glue
layer. After the detection has finished, it will notify USB PHY
charger framework, and the uevents will be triggered.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Call cpu_latency_qos_add/remove_request() instead of
pm_qos_add/remove_request(), respectively, because the
latter are going to be dropped.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
For imx chipidea controllers, if they use mxs PHY, they need pinctrl
for HSIC. Otherwise, it doesn't need pinctrl and usbmisc control. Like
imx7d and imx8mm.
Reported-by: André Draszik <git@andred.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
- -EPROBE_DEFER is an error, but without need show error message
- If pintrol is not existed, as pintrol is NULL
Signed-off-by: Peter Chen <peter.chen@nxp.com>
As usbmisc_data is optional, so add the check before access its member,
this fix below static checker warning:
drivers/usb/chipidea/ci_hdrc_imx.c:438 ci_hdrc_imx_probe()
warn: 'data->usbmisc_data' can also be NULL
which is introduced by Patch 15b80f7c3a7f:
"usb: chipidea: imx: enable vbus and id wakeup only for OTG events"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
If ID or VBUS is from external block, don't enable its wakeup
because it isn't used at all.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Since the chipidea common code support get the USB PHY phandle from
"phys", the glue layer is not mandatory to get the "fsl,usbphy" phandle
any more.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In this commit, we add CI_HDRC_PMQOS to avoid system entering idle,
at imx7ulp, if the system enters idle, the DMA will stop, so the USB
transfer can't work at this case.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds support to set the power line polarity for i.MX SoCs.
To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.
Also make use of of_property_read_bool.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those 2 headers files are not required now.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the static checker, "data->usbmisc_data" may be NULL.
Fix it by adding this pointer judgement before using.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polarity of the over current detection pin isn't configured on i.MX6/7
if it's unspecified in the device tree. So the actual configuration depends
on bootloader behavior which is bad.
So encourage users to fix their device tree by issuing a warning in this
case.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
To support imx HSIC, there are some special requirement:
- The HSIC pad is 1.2v, it may need to supply from external
- The data/strobe pin needs to be pulled down first, and after
host mode is initialized, the strobe pin needs to be pulled up
- During the USB suspend/resume, special setting is needed
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The SPDX-License-Identifier is set to GPL-2.0+, which correspond to
MODULE_LICENSE "GPL".
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Use preprocessor conditionals for CONFIG_PM and CONFIG_PM_SLEEP is
not necessary since SET_SYSTEM_SLEEP_PM_OPS and SET_RUNTIME_PM_OPS does
that internally.
It is also the preferred way according to our coding style guidelines.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Workaround introduced for i.MX53 in be9cae2479 ("usb: chipidea:
imx: Fix ULPI on imx53") seems to be applicable in case of i.MX51 as
well. Running latest kernel on ZII RDU1 Board (imx51-zii-rdu1.dts)
exhibits a kernel frozen on PORTSC access and applying the workaround
resolves the issue.
Fixes: be9cae2479 ("usb: chipidea: imx: Fix ULPI on imx53")
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traditionally, PORTSC should be set before initializing ULPI phys. But
setting PORTSC before powering on the phy results in a kernel freeze
on imx53 based GE PPD. As a workaround this initializes the phy early
in the imx platform code and disables phy power management from the
core.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some trivial cleanups, that do not change functionality.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use ULPI phy with usb host 2 and 3, we need to configure
controller register to enable ULPI features.
Each USB controller have different behaviour, so in order to avoid to have
several "swicth(data->index)" and lock/unlock, we prefer to get the index
switch and then test for features if they exist for this index.
This patch also remove useless test of reg and val. Those two values cannot
be NULL.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx usb over current polarity is low active by default, with
over-current-active-high property added, user can config it to be high
active. Meanwhile keep this setting unchanged for existing platforms
so new platform must set the right value for active low by its usbmisc
init function if over current is enabled.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For each platform devices which is created by device tree, the default
DMA mask is set by of_dma_configure when the device are created. So
delete the redundant code at driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Avoid printing an error if adding the device failes with return
value EPROBE_DEFFER. This may happen e.g. due to missing GPIO for
the vbus-supply regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Xu Yang