The device initialization and termination functions
were messy and convoluted. Introduce helper functions
to clarify init_softc() and simplify things in general.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sc_flags has slowly become a kitchen sink over time.
Move powersave related flags to a separate variable.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move initialization/de-initialization related
code to this file.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all LED/RFKILL/BTCOEX related code
to gpio.c
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enhances the way we parse country IEs to minimize
the number of regulatory rules that we create. It also fixes
our current implementation which treated country IE triplets
with only one channel as one independed regulatory rule even
though adjecent rules were also being provided.
Without this patch APs which send country IE information with
a channel triplet for each individual channel will force cfg80211
to deny HT40 operation as a regulatory rule would have been created
independently for each channel and as such configured only for
20 MHz operation.
Although 802.11n APs which send country IEs triplets in this fassion
are likely rare Benoit reports this against the Ubiquity NanoStation M5,
with Country "FR" and HT40 enabled.
Since we now have a helper which parses the triplets in intermediate
steps we now take care extra care to process padding.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max power from each country IE triplet was being ignored.
This fix isn't critical as CRDA was always being used for the lower
limit, but we should process it in case the AP still wants to
decrease power output even more for whatever reason.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle and Lennert reported problems with the new work
code, and at least Kalle's problem I was able to trace
to a missing jiffies initialisation.
I also ran into a problem where occasionally I couldn't
connect, which seems fixed with kicking the work items
after scanning.
Finally, also add some sanity checking code to verify
that we're not adding work items while an interface is
down -- that case could lead to something similar to
what Lennert was seeing.
There still seems to be a race condition that we're
trying to figure out separately.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store information elements from Beacon and Probe Response frames in
separate buffers to allow both sets to be made available through
nl80211. This allows user space applications to get access to IEs from
Beacon frames even if we have received Probe Response frames from the
BSS. Previously, the IEs from Probe Response frames would have
overridden the IEs from Beacon frames.
This feature is of somewhat limited use since most protocols include
the same (or extended) information in Probe Response frames. However,
there are couple of exceptions where the IEs from Beacon frames could
be of some use: TIM IE is only included in Beacon frames (and it would
be needed to figure out the DTIM period used in the BSS) and at least
some implementations of Wireless Provisioning Services seem to include
the full IE only in Beacon frames).
The new BSS attribute for scan results is added to allow both the IE
sets to be delivered. This is done in a way that maintains the
previously used behavior for applications that are not aware of the
new NL80211_BSS_BEACON_IES attribute.
Signed-off-by: Jouni Malinen <j@w1.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In various cases wl1251_op_bss_info_changed() did not call elp_sleep()
after an error was noticed. Fix it by using correct goto label.
The bug was a theoretical one, in practise it doesn't matter because
if commands start returning errors there will be lots of other problems.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of channels to be used in scan was hard coded in wl1251. The
proper way is to use the channels array provided by mac80211.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of creating the template in driver, get it from mac80211 instead.
Thanks to this, three functions can be now removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current scanning code wasn't following the preferred style. Move code
related to scan and trigger scan to commans to wl1251_cmd.c. Because
there's now less code in wl1251_hw_scan(), the function can be now
merged with wl1251_op_hw_scan().
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mac80211 now has a separate function for creating Probe Request templates,
better to use it when sending direct Probe Requests to an AP. Only the
bssid needs to be updated in the template before sending it.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Certain type of hardware, for example wl1251 and wl1271, need a template
for the Probe Request. Create a function ieee80211_probereq_get() which
creates the template and drivers send it to hardware.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that mac80211 creates templates for PS Poll and Nullfunc frames, use
them instead of creating our own.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To avoid duplicate code, use ieee80211_[pspoll|nullfunc]_get() to get
templates for PS Poll and Nullfunc frames in mlme.c.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware, for example wl1251 and wl1271, handle the transmission
of power save related frames in hardware, but the driver is responsible
for creating the templates. It's better to create the templates in mac80211,
that way all drivers can benefit from this.
Add two new functions, ieee80211_pspoll_get() and ieee80211_nullfunc_get()
which drivers need to call to get the frame. Drivers are also responsible
for updating the templates after each association.
Also new struct ieee80211_hdr_3addr is added to ieee80211.h to make it
easy to calculate length of the Nullfunc frame.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is only used within the rt2800lib module itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800pci_wait_wpdma_ready and rt2800usb_wait_wpdma_ready functions are
exactly the same, so unify them into rt200lib.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RF3052 chipset is now also being integrated onto USB devices, so
allow the RF chipset and don't treat it as PCI/SOC only.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new NL80211_CMD_SET_TX_BITRATE_MASK command and related
attributes to provide support for setting TX rate mask for rate
control. This uses the existing cfg80211 set_bitrate_mask operation
that was previously used only with WEXT compat code (SIOCSIWRATE). The
nl80211 command allows more generic configuration of allowed rates as
a mask instead of fixed/max rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend struct cfg80211_bitrate_mask to actually use a bitfield mask
instead of just a single fixed or maximum rate index. This change
itself does not modify the behavior (except for debugfs files), but it
prepares cfg80211 and mac80211 for a new nl80211 command for setting
which rates can be used in TX rate control.
Since frames are now going through the rate control algorithm
unconditionally, the internal IEEE80211_TX_INTFL_RCALGO flag can now
be removed. The RC implementations can use the rate_idx_mask value to
optimize their behavior if only a single rate is enabled.
The old max_rate_idx in struct ieee80211_tx_rate_control is maintained
(but commented as deprecated) for backwards compatibility with existing
RC implementations. Once these implementations have been updated to
use the more generic rate_idx_mask, the max_rate_idx value can be
removed.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the basic rate set is configured to not include the lowest rate
(e.g., basic rate set = 6, 12, 24 Mbps in IEEE 802.11g mode), the AP
should not send out broadcast frames at 1 Mbps. This type of
configuration can be used to optimize channel usage in cases where
there is no need for backwards compatibility with IEEE 802.11b-only
devices.
In AP mode, mac80211 was unconditionally using the lowest rate for
Beacon frames and similarly, with all rate control algorithms that use
rate_control_send_low(), the lowest rate ended up being used for all
broadcast frames (and all unicast frames that are sent before
association). Change this to take into account the basic rate
configuration in AP mode, i.e., use the lowest rate in the basic rate
set instead of the lowest supported rate when selecting the rate.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make addba_resp_timer aware the HT_AGG_STATE_REQ_STOP_BA_MSK mask
so that when ___ieee80211_stop_tx_ba_session() is issued the timer
will quit. Otherwise when suspend happens before the timer expired,
the timer handler will be called immediately after resume and
messes up driver status.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback sets slot time as specified in IEEE 802.11-2007 section
17.3.8.6 (for 20MHz channels only for now) and raises ACK and CTS
timeouts accordingly. The values are persistent, they are restored after
device reset.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code was correct in 802.11a mode only, 802.11b/g uses
different clock rates. The new code uses values taken from FreeBSD HAL
and should be correct for all modes including turbo modes.
The former rate calculation was used by slope coefficient calculation
function ath5k_hw_write_ofdm_timings. However, this function requires
the 802.11a values even in 802.11g mode. Thus the use of
ath5k_hw_htoclock was replaced by hardcoded values. Possibly the slope
coefficient calculation is not related to clock rate at all.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Functions ath5k_hw_get_slot_time and ath5k_hw_set_slot_time were
converting microseconds to clocks only for AR5210, although it's needed
for all supported devices. The conversion was moved outside the
hardware-specific branches.
The original code also limited minimum slot time to 9, while turbo modes
use 6, this was fixed too.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 callback to driver set_coverage_class() sets slot time and ACK
timeout for given IEEE 802.11 coverage class. The callback is optional,
but it's essential for long distance links.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new attribute NL80211_ATTR_WIPHY_COVERAGE_CLASS sets IEEE 802.11
Coverage Class, which depends on maximum distance of nodes in a
wireless network. It's required for long distance links (more than a few
hundred meters).
The attribute is now ignored by two non-mac80211 drivers, rndis and
iwmc3200wifi, together with WIPHY_PARAM_RETRY_SHORT and
WIPHY_PARAM_RETRY_LONG. If it turns out to be a problem, we could split
set_wiphy_params callback or add new capability bits.
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The newer single chip hardware family of chipsets have not been
experiencing issues with power saving set by default with recent
fixes merged (even into stable). The remaining issues are only
reported with AR5416 and since enabling PS by default can increase
power savings considerably best to take advantage of that feature
as this has been tested properly.
For more details on this issue see the bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=14267
We leave AR5416 with PS disabled by default, that seems to require
some more work.
Cc: stable@kernel.org
Cc: Peter Stuge <peter@stuge.se>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_CFG80211_WEXT is not set, there is
a refcount imbalance with rdev->opencount, fix
that by moving it out of the ifdef.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ieee80211_monitor_select_queue encounters data frames, it selects
the WMM AC based on skb->priority and assumes that skb->priority
contains a valid 802.1d tag. However this assumption is incorrect, since
ieee80211_select_queue has not been called at this point.
If skb->priority > 7, an array overrun occurs, which could lead to
invalid values, resulting in crashes in the tx path.
Fix this by setting skb->priority based on the 802.11 header for QoS
frames and using the default AC for all non-QoS frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Smatch (and presumably other static checkers) complain that MAX_TID_COUNT is
past the end of the array. In the resulting discussion, Zhu Yi pointed out
that this value is not used in real life and the assignment was only there to
silence a gcc warning.
If there were a bug in the surrounding code and the value were used, the
WARN_ON(!qc) would print a warning before the crash.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On beacon change update notification from mac we are not disabling
the tx in adhoc mode. Mac sends BSS_CHANGED_BEACON_ENABLED when
station leaves IBSS. Driver should indicate uCode to not to send
anything on receiving this notification.
Functionality to indicate uCode is duplicated across
two notifications so created a common function called iwl_set_no_assoc.
Fix the issue at
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2133.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot to convert the radiotap length to
CPU endian, which sparse found thankfully.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various missing sanity checks caused rejected action frames to be
interpreted as channel switch announcements, which can cause a client
mode interface to switch away from its operating channel, thereby losing
connectivity. This patch ensures that only spectrum management action
frames are processed by the CSA handling function and prevents rejected
action frames from getting processed by the MLME code.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 'mac80211: fix skb buffering issue' added an ->ndo_select_queue()
for monitor interfaces which can end up dereferencing ieee802_1d_to_ac[]
beyond the end of the array for injected data packets (as skb->priority
isn't guaranteed to be zero or within [0:7]), which then triggers the
WARN_ON in net/core/dev.c:dev_cap_txqueue(). Fix this by always setting
the priority to zero on injected data frames.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 53623f1a09.
This was inadvertantly missed in "mac80211: fix skb buffering issue",
and is required with that patch to restore proper queue operation.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix skb buffering issue" is based on what will become 2.6.34,
so it includes an incompatible usage of sta_info_get. This patch will
need to be effectively reverted when merging for 2.6.34.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The start_seq_num is taken from the station's tid_seq[tid].
This is fine, except tid_seq sequence counter is shifted
by 4 bits to accommodate for frame fragmentation.
Both (iwlagn & ath9k) were unaffected by this minor glitch,
because they don't read the *ssn for the AMPDU_TX_START action.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables HT association and AMPDU in the receive direction for
STA firmware images on hardware that supports it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AMPDU receive doesn't need any special handling, so let's enable
this before tackling the transmit side.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass the AP's MCS rate mask to SET_RATE when associating, and make
UPDATE_STADB pass in the peer's HT caps and rates when adding a new
hardware station database entry.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith