Assume that if the guest executes clts, it knows what it's doing, and load the
guest fpu to prevent an #NM exception.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This allows accessing the guest fpu from the instruction emulator, as well as
being symmetric with kvm_put_guest_fpu().
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move to/from Control Registers chapter of Intel SDM says. "Reserved bits
in CR0 remain clear after any load of those registers; attempts to set
them have no impact". Control Register chapter says "Bits 63:32 of CR0 are
reserved and must be written with zeros. Writing a nonzero value to any
of the upper 32 bits results in a general-protection exception, #GP(0)."
This patch tries to implement this twisted logic.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Reported-by: Lorenzo Martignoni <martignlo@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Enhance mov dr instruction emulation used by SVM so that it properly
handles dr4/5: alias to dr6/7 if cr4.de is cleared. Otherwise return
EMULATE_FAIL which will let our only possible caller in that scenario,
ud_interception, re-inject UD.
We do not need to inject faults, SVM does this for us (exceptions take
precedence over instruction interceptions). For the same reason, the
value overflow checks can be removed.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Windows issues this hypercall after guest was spinning on a spinlock
for too many iterations.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Vadim Rozenfeld <vrozenfe@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Defer fpu deactivation as much as possible - if the guest fpu is loaded, keep
it loaded until the next heavyweight exit (where we are forced to unload it).
This reduces unnecessary exits.
We also defer fpu activation on clts; while clts signals the intent to use the
fpu, we can't be sure the guest will actually use it.
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we'd like to allow the guest to own a few bits of cr0 at times, we need
to know when we access those bits.
Signed-off-by: Avi Kivity <avi@redhat.com>
Then the callback can provide the maximum supported large page level, which
is more flexible.
Also move the gb page support into x86_64 specific.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Have a pointer to an allocated region inside struct kvm.
[alex: fix ppc book 3s]
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Before enabling, execution of "rdtscp" in guest would result in #UD.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Sometime, we need to adjust some state in order to reflect guest CPUID
setting, e.g. if we don't expose rdtscp to guest, we won't want to enable
it on hardware. cpuid_update() is introduced for this purpose.
Also export kvm_find_cpuid_entry() for later use.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
shared_msr_global saved host value of relevant MSRs, but it have an
assumption that all MSRs it tracked shared the value across the different
CPUs. It's not true with some MSRs, e.g. MSR_TSC_AUX.
Extend it to per CPU to provide the support of MSR_TSC_AUX, and more
alike MSRs.
Notice now the shared_msr_global still have one assumption: it can only deal
with the MSRs that won't change in host after KVM module loaded.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some bits of cr4 can be owned by the guest on vmx, so when we read them,
we copy them to the vcpu structure. In preparation for making the set of
guest-owned bits dynamic, use helpers to access these bits so we don't need
to know where the bit resides.
No changes to svm since all bits are host-owned there.
Signed-off-by: Avi Kivity <avi@redhat.com>
Windows 2003 uses task switch to triple fault and reboot (the other
exception being reserved pdptrs bits).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move Double-Fault generation logic out of page fault
exception generating function to cover more generic case.
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Current kvm wallclock does not consider the total_sleep_time which could cause
wrong wallclock in guest after host suspend/resume. This patch solve
this issue by counting total_sleep_time to get the correct host boot time.
Cc: stable@kernel.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
In function kvm_arch_vcpu_init(), if the memory malloc for
vcpu->arch.mce_banks is fail, it does not free the memory
of lapic date. This patch fixed it.
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
vcpu->arch.mce_banks is malloc in kvm_arch_vcpu_init(), but
never free in any place, this may cause memory leak. So this
patch fixed to free it in kvm_arch_vcpu_uninit().
Cc: stable@kernel.org
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
User space may not want to overwrite asynchronously changing VCPU event
states on write-back. So allow to skip nmi.pending and sipi_vector by
setting corresponding bits in the flags field of kvm_vcpu_events.
[avi: advertise the bits in KVM_GET_VCPU_EVENTS]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (84 commits)
KVM: VMX: Fix comparison of guest efer with stale host value
KVM: s390: Fix prefix register checking in arch/s390/kvm/sigp.c
KVM: Drop user return notifier when disabling virtualization on a cpu
KVM: VMX: Disable unrestricted guest when EPT disabled
KVM: x86 emulator: limit instructions to 15 bytes
KVM: s390: Make psw available on all exits, not just a subset
KVM: x86: Add KVM_GET/SET_VCPU_EVENTS
KVM: VMX: Report unexpected simultaneous exceptions as internal errors
KVM: Allow internal errors reported to userspace to carry extra data
KVM: Reorder IOCTLs in main kvm.h
KVM: x86: Polish exception injection via KVM_SET_GUEST_DEBUG
KVM: only clear irq_source_id if irqchip is present
KVM: x86: disallow KVM_{SET,GET}_LAPIC without allocated in-kernel lapic
KVM: x86: disallow multiple KVM_CREATE_IRQCHIP
KVM: VMX: Remove vmx->msr_offset_efer
KVM: MMU: update invlpg handler comment
KVM: VMX: move CR3/PDPTR update to vmx_set_cr3
KVM: remove duplicated task_switch check
KVM: powerpc: Fix BUILD_BUG_ON condition
KVM: VMX: Use shared msr infrastructure
...
Trivial conflicts due to new Kconfig options in arch/Kconfig and kernel/Makefile
update_transition_efer() masks out some efer bits when deciding whether
to switch the msr during guest entry; for example, NX is emulated using the
mmu so we don't need to disable it, and LMA/LME are handled by the hardware.
However, with shared msrs, the comparison is made against a stale value;
at the time of the guest switch we may be running with another guest's efer.
Fix by deferring the mask/compare to the actual point of guest entry.
Noted by Marcelo.
Signed-off-by: Avi Kivity <avi@redhat.com>
This way, we don't leave a dangling notifier on cpu hotunplug or module
unload. In particular, module unload leaves the notifier pointing into
freed memory.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This new IOCTL exports all yet user-invisible states related to
exceptions, interrupts, and NMIs. Together with appropriate user space
changes, this fixes sporadic problems of vmsave/restore, live migration
and system reset.
[avi: future-proof abi by adding a flags field]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Decouple KVM_GUESTDBG_INJECT_DB and KVM_GUESTDBG_INJECT_BP from
KVM_GUESTDBG_ENABLE, their are actually orthogonal. At this chance,
avoid triggering the WARN_ON in kvm_queue_exception if there is already
an exception pending and reject such invalid requests.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Otherwise kvm will leak memory on multiple KVM_CREATE_IRQCHIP.
Also serialize multiple accesses with kvm->lock.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
GUEST_CR3 is updated via kvm_set_cr3 whenever CR3 is modified from
outside guest context. Similarly pdptrs are updated via load_pdptrs.
Let kvm_set_cr3 perform the update, removing it from the vcpu_run
fast path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Acked-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The various syscall-related MSRs are fairly expensive to switch. Currently
we switch them on every vcpu preemption, which is far too often:
- if we're switching to a kernel thread (idle task, threaded interrupt,
kernel-mode virtio server (vhost-net), for example) and back, then
there's no need to switch those MSRs since kernel threasd won't
be exiting to userspace.
- if we're switching to another guest running an identical OS, most likely
those MSRs will have the same value, so there's little point in reloading
them.
- if we're running the same OS on the guest and host, the MSRs will have
identical values and reloading is unnecessary.
This patch uses the new user return notifiers to implement last-minute
switching, and checks the msr values to avoid unnecessary reloading.
Signed-off-by: Avi Kivity <avi@redhat.com>
When we migrate a kvm guest that uses pvclock between two hosts, we may
suffer a large skew. This is because there can be significant differences
between the monotonic clock of the hosts involved. When a new host with
a much larger monotonic time starts running the guest, the view of time
will be significantly impacted.
Situation is much worse when we do the opposite, and migrate to a host with
a smaller monotonic clock.
This proposed ioctl will allow userspace to inform us what is the monotonic
clock value in the source host, so we can keep the time skew short, and
more importantly, never goes backwards. Userspace may also need to trigger
the current data, since from the first migration onwards, it won't be
reflected by a simple call to clock_gettime() anymore.
[marcelo: future-proof abi with a flags field]
[jan: fix KVM_GET_CLOCK by clearing flags field instead of checking it]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 705c5323 opened the doors of hell by unconditionally injecting
single-step flags as long as guest_debug signaled this. This doesn't
work when the guest branches into some interrupt or exception handler
and triggers a vmexit with flag reloading.
Fix it by saving cs:rip when user space requests single-stepping and
restricting the trace flag injection to this guest code position.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Support for Xen PV-on-HVM guests can be implemented almost entirely in
userspace, except for handling one annoying MSR that maps a Xen
hypercall blob into guest address space.
A generic mechanism to delegate MSR writes to userspace seems overkill
and risks encouraging similar MSR abuse in the future. Thus this patch
adds special support for the Xen HVM MSR.
I implemented a new ioctl, KVM_XEN_HVM_CONFIG, that lets userspace tell
KVM which MSR the guest will write to, as well as the starting address
and size of the hypercall blobs (one each for 32-bit and 64-bit) that
userspace has loaded from files. When the guest writes to the MSR, KVM
copies one page of the blob from userspace to the guest.
I've tested this patch with a hacked-up version of Gerd's userspace
code, booting a number of guests (CentOS 5.3 i386 and x86_64, and
FreeBSD 8.0-RC1 amd64) and exercising PV network and block devices.
[jan: fix i386 build warning]
[avi: future proof abi with a flags field]
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This (broken) check dates back to the days when this code was shared
across architectures. x86 has IOMEM, so drop it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
If cpufreq can't determine the CPU khz, or cpufreq is not compiled in,
we should fallback to the measured TSC khz.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for the event that the guest
executed the SKINIT instruction. This information is
important because SKINIT is an SVM extenstion not yet
implemented by nested SVM and we may need this information
for debugging hypervisors that do not yet run on nested SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for the event that the guest
executed the INVLPGA instruction.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a special tracepoint for the event that a
nested #vmexit is injected because kvm wants to inject an
interrupt into the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for a nested #vmexit that gets
re-injected to the guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a tracepoint for every #vmexit we get from a
nested guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch adds a dedicated kvm tracepoint for a nested
vmrun.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
For a while now, we are issuing a rdmsr instruction to find out which
msrs in our save list are really supported by the underlying machine.
However, it fails to account for kvm-specific msrs, such as the pvclock
ones.
This patch moves then to the beginning of the list, and skip testing them.
Cc: stable@kernel.org
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Push TF and RF injection and filtering on guest single-stepping into the
vender get/set_rflags callbacks. This makes the whole mechanism more
robust wrt user space IOCTL order and instruction emulations.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Disable paravirt MMU capability reporting, so that new (or rebooted)
guests switch to native operation.
Paravirt MMU is a burden to maintain and does not bring significant
advantages compared to shadow anymore.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Much of so far vendor-specific code for setting up guest debug can
actually be handled by the generic code. This also fixes a minor deficit
in the SVM part /wrt processing KVM_GUESTDBG_ENABLE.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
They are globals, not clearly protected by any ordering or locking, and
vulnerable to various startup races.
Instead, for variable TSC machines, register the cpufreq notifier and get
the TSC frequency directly from the cpufreq machinery. Not only is it
always right, it is also perfectly accurate, as no error prone measurement
is required.
On such machines, when a new CPU online is brought online, it isn't clear what
frequency it will start with, and it may not correspond to the reference, thus
in hardware_enable we clear the cpu_tsc_khz variable to zero and make sure
it is set before running on a VCPU.
Signed-off-by: Zachary Amsden <zamsden@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
X86 CPUs need to have some magic happening to enable the virtualization
extensions on them. This magic can result in unpleasant results for
users, like blocking other VMMs from working (vmx) or using invalid TLB
entries (svm).
Currently KVM activates virtualization when the respective kernel module
is loaded. This blocks us from autoloading KVM modules without breaking
other VMMs.
To circumvent this problem at least a bit, this patch introduces on
demand activation of virtualization. This means, that instead
virtualization is enabled on creation of the first virtual machine
and disabled on destruction of the last one.
So using this, KVM can be easily autoloaded, while keeping other
hypervisors usable.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The only thing it protects now is interrupt injection into lapic and
this can work lockless. Even now with kvm->irq_lock in place access
to lapic is not entirely serialized since vcpu access doesn't take
kvm->irq_lock.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Conflicts:
arch/x86/kernel/kprobes.c
kernel/trace/Makefile
Merge reason: hw-breakpoints perf integration is looking
good in testing and in reviews, plus conflicts
are mounting up - so merge & resolve.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Wrap in the cpu dr7 check that tells if we have active
breakpoints that need to be restored in the cpu.
This wrapper makes the check more self-explainable and also
reusable for any further other uses.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: "K. Prasad" <prasad@linux.vnet.ibm.com>
This patch rebase the implementation of the breakpoints API on top of
perf events instances.
Each breakpoints are now perf events that handle the
register scheduling, thread/cpu attachment, etc..
The new layering is now made as follows:
ptrace kgdb ftrace perf syscall
\ | / /
\ | / /
/
Core breakpoint API /
/
| /
| /
Breakpoints perf events
|
|
Breakpoints PMU ---- Debug Register constraints handling
(Part of core breakpoint API)
|
|
Hardware debug registers
Reasons of this rewrite:
- Use the centralized/optimized pmu registers scheduling,
implying an easier arch integration
- More powerful register handling: perf attributes (pinned/flexible
events, exclusive/non-exclusive, tunable period, etc...)
Impact:
- New perf ABI: the hardware breakpoints counters
- Ptrace breakpoints setting remains tricky and still needs some per
thread breakpoints references.
Todo (in the order):
- Support breakpoints perf counter events for perf tools (ie: implement
perf_bpcounter_event())
- Support from perf tools
Changes in v2:
- Follow the perf "event " rename
- The ptrace regression have been fixed (ptrace breakpoint perf events
weren't released when a task ended)
- Drop the struct hw_breakpoint and store generic fields in
perf_event_attr.
- Separate core and arch specific headers, drop
asm-generic/hw_breakpoint.h and create linux/hw_breakpoint.h
- Use new generic len/type for breakpoint
- Handle off case: when breakpoints api is not supported by an arch
Changes in v3:
- Fix broken CONFIG_KVM, we need to propagate the breakpoint api
changes to kvm when we exit the guest and restore the bp registers
to the host.
Changes in v4:
- Drop the hw_breakpoint_restore() stub as it is only used by KVM
- EXPORT_SYMBOL_GPL hw_breakpoint_restore() as KVM can be built as a
module
- Restore the breakpoints unconditionally on kvm guest exit:
TIF_DEBUG_THREAD doesn't anymore cover every cases of running
breakpoints and vcpu->arch.switch_db_regs might not always be
set when the guest used debug registers.
(Waiting for a reliable optimization)
Changes in v5:
- Split-up the asm-generic/hw-breakpoint.h moving to
linux/hw_breakpoint.h into a separate patch
- Optimize the breakpoints restoring while switching from kvm guest
to host. We only want to restore the state if we have active
breakpoints to the host, otherwise we don't care about messed-up
address registers.
- Add asm/hw_breakpoint.h to Kbuild
- Fix bad breakpoint type in trace_selftest.c
Changes in v6:
- Fix wrong header inclusion in trace.h (triggered a build
error with CONFIG_FTRACE_SELFTEST
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jan Kiszka <jan.kiszka@web.de>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Paul Mundt <lethal@linux-sh.org>
If TSS we are switching to resides in high memory task switch will fail
since address will be truncated. Windows2k3 does this sometimes when
running with more then 4G
Cc: stable@kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We only allocate memory for 32 MCE banks (KVM_MAX_MCE_BANKS) but we
allow user space to fill up to 255 on setup (mcg_cap & 0xff), corrupting
kernel memory. Catch these overflows.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Conflicts:
kernel/Makefile
kernel/trace/Makefile
kernel/trace/trace.h
samples/Makefile
Merge reason: We need to be uptodate with the perf events development
branch because we plan to rewrite the breakpoints API on top of
perf events.
The number of entries is multiplied by the entry size, which can
overflow on 32-bit hosts. Bound the entry count instead.
Reported-by: David Wagner <daw@cs.berkeley.edu>
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'kvm-updates/2.6.32' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (202 commits)
MAINTAINERS: update KVM entry
KVM: correct error-handling code
KVM: fix compile warnings on s390
KVM: VMX: Check cpl before emulating debug register access
KVM: fix misreporting of coalesced interrupts by kvm tracer
KVM: x86: drop duplicate kvm_flush_remote_tlb calls
KVM: VMX: call vmx_load_host_state() only if msr is cached
KVM: VMX: Conditionally reload debug register 6
KVM: Use thread debug register storage instead of kvm specific data
KVM guest: do not batch pte updates from interrupt context
KVM: Fix coalesced interrupt reporting in IOAPIC
KVM guest: fix bogus wallclock physical address calculation
KVM: VMX: Fix cr8 exiting control clobbering by EPT
KVM: Optimize kvm_mmu_unprotect_page_virt() for tdp
KVM: Document KVM_CAP_IRQCHIP
KVM: Protect update_cr8_intercept() when running without an apic
KVM: VMX: Fix EPT with WP bit change during paging
KVM: Use kvm_{read,write}_guest_virt() to read and write segment descriptors
KVM: x86 emulator: Add adc and sbb missing decoder flags
KVM: Add missing #include
...
Debug registers may only be accessed from cpl 0. Unfortunately, vmx will
code to emulate the instruction even though it was issued from guest
userspace, possibly leading to an unexpected trap later.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Instead of saving the debug registers from the processor to a kvm data
structure, rely in the debug registers stored in the thread structure.
This allows us not to save dr6 and dr7.
Reduces lightweight vmexit cost by 350 cycles, or 11 percent.
Signed-off-by: Avi Kivity <avi@redhat.com>
Segment descriptors tables can be placed on two non-contiguous pages.
This patch makes reading segment descriptors by linear address.
Signed-off-by: Mikhail Ershov <Mike.Ershov@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
According to 16.2.5 in the SDM, eflags.vm in the tss is consulted before loading
and new segments. If eflags.vm == 1, then the segments are treated as 16-bit
segments. The LDTR and TR are not normally available in vm86 mode so if they
happen to somehow get loaded, they need to be treated as 32-bit segments.
This fixes an invalid vmentry failure in a custom OS that was happening after
a task switch into vm8086 mode. Since the segments were being mistakenly
treated as 32-bit, we loaded garbage state.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since on vcpu entry we do it only if apic is enabled we should do
it when TPR is changed while apic is disabled. This happens when windows
resets HW without setting TPR to zero.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We ignore writes to the perfctr msrs. Ignore reads as well.
Kaspersky antivirus crashes Windows guests if it can't read
these MSRs.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far unprivileged guest callers running in ring 3 can issue, e.g., MMU
hypercalls. Normally, such callers cannot provide any hand-crafted MMU
command structure as it has to be passed by its physical address, but
they can still crash the guest kernel by passing random addresses.
To close the hole, this patch considers hypercalls valid only if issued
from guest ring 0. This may still be relaxed on a per-hypercall base in
the future once required.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If userspace knows that the kernel part supports 1GB pages it can enable
the corresponding cpuid bit so that guests actually use GB pages.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit f0a3602c20 ("KVM: Move interrupt injection logic to x86.c") does not
update the cr8 intercept if the lapic is disabled, so when userspace updates
cr8, the cr8 threshold control is not updated and we are left with illegal
control fields.
Fix by explicitly resetting the cr8 threshold.
Signed-off-by: Avi Kivity <avi@redhat.com>
Now KVM allow guest to modify guest's physical address of EPT's identity mapping page.
(change from v1, discard unnecessary check, change ioctl to accept parameter
address rather than value)
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use kvm_get_gdt() and kvm_read_ldt() to reduce inline assembly code.
Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Use get_desc_base() and get_desc_limit() to get the base address and
limit in desc_struct.
Cc: Avi Kivity <avi@redhat.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Remove kvm_cpu_has_interrupt() and kvm_arch_interrupt_allowed() from
interface between general code and arch code. kvm_arch_vcpu_runnable()
checks for interrupts instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
ioeventfd is a mechanism to register PIO/MMIO regions to trigger an eventfd
signal when written to by a guest. Host userspace can register any
arbitrary IO address with a corresponding eventfd and then pass the eventfd
to a specific end-point of interest for handling.
Normal IO requires a blocking round-trip since the operation may cause
side-effects in the emulated model or may return data to the caller.
Therefore, an IO in KVM traps from the guest to the host, causes a VMX/SVM
"heavy-weight" exit back to userspace, and is ultimately serviced by qemu's
device model synchronously before returning control back to the vcpu.
However, there is a subclass of IO which acts purely as a trigger for
other IO (such as to kick off an out-of-band DMA request, etc). For these
patterns, the synchronous call is particularly expensive since we really
only want to simply get our notification transmitted asychronously and
return as quickly as possible. All the sychronous infrastructure to ensure
proper data-dependencies are met in the normal IO case are just unecessary
overhead for signalling. This adds additional computational load on the
system, as well as latency to the signalling path.
Therefore, we provide a mechanism for registration of an in-kernel trigger
point that allows the VCPU to only require a very brief, lightweight
exit just long enough to signal an eventfd. This also means that any
clients compatible with the eventfd interface (which includes userspace
and kernelspace equally well) can now register to be notified. The end
result should be a more flexible and higher performance notification API
for the backend KVM hypervisor and perhipheral components.
To test this theory, we built a test-harness called "doorbell". This
module has a function called "doorbell_ring()" which simply increments a
counter for each time the doorbell is signaled. It supports signalling
from either an eventfd, or an ioctl().
We then wired up two paths to the doorbell: One via QEMU via a registered
io region and through the doorbell ioctl(). The other is direct via
ioeventfd.
You can download this test harness here:
ftp://ftp.novell.com/dev/ghaskins/doorbell.tar.bz2
The measured results are as follows:
qemu-mmio: 110000 iops, 9.09us rtt
ioeventfd-mmio: 200100 iops, 5.00us rtt
ioeventfd-pio: 367300 iops, 2.72us rtt
I didn't measure qemu-pio, because I have to figure out how to register a
PIO region with qemu's device model, and I got lazy. However, for now we
can extrapolate based on the data from the NULLIO runs of +2.56us for MMIO,
and -350ns for HC, we get:
qemu-pio: 153139 iops, 6.53us rtt
ioeventfd-hc: 412585 iops, 2.37us rtt
these are just for fun, for now, until I can gather more data.
Here is a graph for your convenience:
http://developer.novell.com/wiki/images/7/76/Iofd-chart.png
The conclusion to draw is that we save about 4us by skipping the userspace
hop.
--------------------
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When kvm is in hpet_legacy_mode, the hpet is providing the timer
interrupt and the pit should not be. So in legacy mode, the pit timer
is destroyed, but the *state* of the pit is maintained. So if kvm or
the guest tries to modify the state of the pit, this modification is
accepted, *except* that the timer isn't actually started. When we exit
hpet_legacy_mode, the current state of the pit (which is up to date
since we've been accepting modifications) is used to restart the pit
timer.
The saved_mode code in kvm_pit_load_count temporarily changes mode to
0xff in order to destroy the timer, but then restores the actual
value, again maintaining "current" state of the pit for possible later
reenablement.
[avi: add some reserved storage in the ioctl; make SET_PIT2 IOW]
[marcelo: fix memory corruption due to reserved storage]
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We emulate x2apic in software, so host support is not required.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will save a couple of IPIs.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some Windows versions check whether the BIOS has setup MMI/O for
config space accesses on AMD Fam10h CPUs, we say "no" by returning 0 on
reads and only allow disabling of MMI/O CfgSpace setup by igoring "0" writes.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This reverts commit 6c20e1442bb1c62914bb85b7f4a38973d2a423ba.
To my understanding, it became obsolete with the advent of the more
robust check in mmu_alloc_roots (89da4ff17f). Moreover, it prevents
the conceptually safe pattern
1. set sregs
2. register mem-slots
3. run vcpu
by setting a sticky triple fault during step 1.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Windows 7 tries to update the CPU's microcode on some processors,
so we ignore the MSR write here. The patchlevel register is already handled
(returning 0), because the MSR number is the same as Intel's.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch implements MSR interface to local apic as defines by x2apic
Intel specification.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Directed EOI is specified by x2APIC, but is available even when lapic is
in xAPIC mode.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux guests will try to enable access to the extended PCI config space
via the I/O ports 0xCF8/0xCFC on AMD Fam10h CPU. Since we (currently?)
don't use ECS, simply ignore write and read attempts.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This changes bus accesses to use high-level kvm_io_bus_read/kvm_io_bus_write
functions. in_range now becomes unused so it is removed from device ops in
favor of read/write callbacks performing range checks internally.
This allows aliasing (mostly for in-kernel virtio), as well as better error
handling by making it possible to pass errors up to userspace.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
switch pit creation to slots_lock. slots_lock is already taken for read
everywhere, so we only need to take it for write when creating pit.
This is in preparation to removing in_range and kvm->lock around it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM will inject a #GP into the guest if that tries to access unhandled
MSRs. This will crash many guests. Although it would be the correct
way to actually handle these MSRs, we introduce a runtime switchable
module param called "ignore_msrs" (defaults to 0). If this is Y, unknown
MSR reads will return 0, while MSR writes are simply dropped. In both cases
we print a message to dmesg to inform the user about that.
You can change the behaviour at any time by saying:
# echo 1 > /sys/modules/kvm/parameters/ignore_msrs
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the Linux kernel detects an C1E capable AMD processor (K8 RevF and
higher), it will access a certain MSR on every attempt to go to halt.
Explicitly handle this read and return 0 to let KVM run a Linux guest
with the native AMD host CPU propagated to the guest.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Linux tries to disable the flush filter on all AMD K8 CPUs. Since KVM
does not handle the needed MSR, the injected #GP will panic the Linux
kernel. Ignore setting of the HWCR.FFDIS bit in this MSR to let Linux
boot with an AMD K8 family guest CPU.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Correct missing locking in a few places in x86's vm_ioctl handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the opcodes for syscall, sysenter and sysexit to the list of instructions
handled by the undefined opcode handler.
Signed-off-by: Christoph Egger <christoph.egger@amd.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This allows use of the powerful ftrace infrastructure.
See Documentation/trace/ for usage information.
[avi, stephen: various build fixes]
[sheng: fix control register breakage]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Replace previous exception with a new one in a hope that instruction
re-execution will regenerate lost exception.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The performance counter MSRs are different for AMD and Intel CPUs and they
are chosen mainly by the CPUID vendor string. This patch catches writes to
all addresses (regardless of VMX/SVM path) and handles them in the generic
MSR handler routine. Writing a 0 into the event select register is something
we perfectly emulate ;-), so don't print out a warning to dmesg in this
case.
This fixes booting a 64bit Windows guest with an AMD CPUID on an Intel host.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since the guest and host ptes can have wildly different format, adjust
the pte accessor names to indicate on which type of pte they operate on.
No functional changes.
Signed-off-by: Avi Kivity <avi@redhat.com>
Protect irq injection/acking data structures with a separate irq_lock
mutex. This fixes the following deadlock:
CPU A CPU B
kvm_vm_ioctl_deassign_dev_irq()
mutex_lock(&kvm->lock); worker_thread()
-> kvm_deassign_irq() -> kvm_assigned_dev_interrupt_work_handler()
-> deassign_host_irq() mutex_lock(&kvm->lock);
-> cancel_work_sync() [blocked]
[gleb: fix ia64 path]
Reported-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of reloading the pdptrs on every entry and exit (vmcs writes on vmx,
guest memory access on svm) extract them on demand.
Signed-off-by: Avi Kivity <avi@redhat.com>
We modernize the io_device code so that we use container_of() instead of
dev->private, and move the vtable to a separate ops structure
(theoretically allows better caching for multiple instances of the same
ops structure)
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
The in-kernel speaker emulation is only a dummy and also unneeded from
the performance point of view. Rather, it takes user space support to
generate sound output on the host, e.g. console beeps.
To allow this, introduce KVM_CREATE_PIT2 which controls in-kernel
speaker port emulation via a flag passed along the new IOCTL. It also
leaves room for future extensions of the PIT configuration interface.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM provides a complete virtual system environment for guests, including
support for injecting interrupts modeled after the real exception/interrupt
facilities present on the native platform (such as the IDT on x86).
Virtual interrupts can come from a variety of sources (emulated devices,
pass-through devices, etc) but all must be injected to the guest via
the KVM infrastructure. This patch adds a new mechanism to inject a specific
interrupt to a guest using a decoupled eventfd mechnanism: Any legal signal
on the irqfd (using eventfd semantics from either userspace or kernel) will
translate into an injected interrupt in the guest at the next available
interrupt window.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The problem exists only on VMX. Also currently we skip this step if
there is pending exception. The patch fixes this too.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If we run out of cpuid entries for extended request types
we should return -E2BIG, just like we do for the standard
request types.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Replace 0xc0010010 with MSR_K8_SYSCFG and 0xc0010015 with MSR_K7_HWCR.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The related MSRs are emulated. MCE capability is exported via
extension KVM_CAP_MCE and ioctl KVM_X86_GET_MCE_CAP_SUPPORTED. A new
vcpu ioctl command KVM_X86_SETUP_MCE is used to setup MCE emulation
such as the mcg_cap. MCE is injected via vcpu ioctl command
KVM_X86_SET_MCE. Extended machine-check state (MCG_EXT_P) and CMCI are
not implemented.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use standard msr-index.h's MSR declaration.
MSR_IA32_TSC is better than MSR_IA32_TIME_STAMP_COUNTER as it also solves
80 column issue.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Do not allow invalid memory types in MTRR/PAT (generating a #GP
otherwise).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far, KVM copied the emulated_msrs (only MSR_IA32_MISC_ENABLE) to a
wrong address in user space due to broken pointer arithmetic. This
caused subtle corruption up there (missing MSR_IA32_MISC_ENABLE had
probably no practical relevance). Moreover, the size check for the
user-provided kvm_msr_list forgot about emulated MSRs.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In commit 7fe29e0faa we ignored the
reads to the P6 EVNTSEL MSRs. That fixed crashes on Intel machines.
Ignore the reads to K7 EVNTSEL MSRs as well to fix this on AMD
hosts.
This fixes Kaspersky antivirus crashing Windows guests on AMD hosts.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
INTn will be re-executed after migration. If we wanted to migrate
pending software interrupt we would need to migrate interrupt type
and instruction length too, but we do not have all required info on
SVM, so SVM->VMX migration would need to re-execute INTn anyway. To
make it simple never migrate pending soft interrupt.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently they are not requested if there is pending exception.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Re-inject event instead. This is what Intel suggest. Also use correct
instruction length when re-injecting soft fault/interrupt.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Only one interrupt vector can be injected from userspace irqchip at
any given time so no need to store it in a bitmap. Put it into interrupt
queue directly.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Verify the cr3 address stored in vcpu->arch.cr3 points to an existant
memslot. If not, inject a triple fault.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_handle_hva, called by MMU notifiers, manipulates mmu data only with
the protection of mmu_lock.
Update kvm_mmu_change_mmu_pages callers to take mmu_lock, thus protecting
against kvm_handle_hva.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We currently unblock shadow interrupt state when we skip an instruction,
but failing to do so when we actually emulate one. This blocks interrupts
in key instruction blocks, in particular sti; hlt; sequences
If the instruction emulated is an sti, we have to block shadow interrupts.
The same goes for mov ss. pop ss also needs it, but we don't currently
emulate it.
Without this patch, I cannot boot gpxe option roms at vmx machines.
This is described at https://bugzilla.redhat.com/show_bug.cgi?id=494469
Signed-off-by: Glauber Costa <glommer@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch replaces drop_interrupt_shadow with the more
general set_interrupt_shadow, that can either drop or raise
it, depending on its parameter. It also adds ->get_interrupt_shadow()
for future use.
Signed-off-by: Glauber Costa <glommer@redhat.com>
CC: H. Peter Anvin <hpa@zytor.com>
CC: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM uses a function call IPI to cause the exit of a guest running on a
physical cpu. For virtual interrupt notification there is no need to
wait on IPI receival, or to execute any function.
This is exactly what the reschedule IPI does, without the overhead
of function IPI. So use it instead of smp_call_function_single in
kvm_vcpu_kick.
Also change the "guest_mode" variable to a bit in vcpu->requests, and
use that to collapse multiple IPI's that would be issued between the
first one and zeroing of guest mode.
This allows kvm_vcpu_kick to called with interrupts disabled.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
MTRR, PAT, MCE, and MCA are all supported (to some extent) but not reported.
Vista requires these features, so if userspace relies on kernel cpuid
reporting, it loses support for Vista.
Signed-off-by: Avi Kivity <avi@redhat.com>
The stats entry request_nmi is no longer used as the related user space
interface was dropped. So clean it up.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Shadow_mt_mask is out of date, now it have only been used as a flag to indicate
if TDP enabled. Get rid of it and use tdp_enabled instead.
Also put memory type logical in kvm_x86_ops->get_mt_mask().
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This moves the get_cpu() call down to be called after we wake up the
waiters. Therefore the waitqueue locks can safely be rt mutex.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Sven-Thorsten Dietrich <sven@thebigcorporation.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It just returns pending IRQ vector from the queue for VMX/SVM.
Get IRQ directly from the queue before migration and put it back
after.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Re-put pending IRQ vector into interrupt_bitmap before migration.
Otherwise it will be lost if migration happens in the wrong time.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_arch_interrupt_allowed() also checks IF so drop the check.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use the same callback to inject irq/nmi events no matter what irqchip is
in use. Only from VMX for now.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
At the vector level, kernel and userspace irqchip are fairly similar.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Matt T. Yourst notes that kvm_arch_vcpu_ioctl_set_sregs lacks validity
checking for the new cr3 value:
"Userspace callers of KVM_SET_SREGS can pass a bogus value of cr3 to
the kernel. This will trigger a NULL pointer access in gfn_to_rmap()
when userspace next tries to call KVM_RUN on the affected VCPU and kvm
attempts to activate the new non-existent page table root.
This happens since kvm only validates that cr3 points to a valid guest
physical memory page when code *inside* the guest sets cr3. However, kvm
currently trusts the userspace caller (e.g. QEMU) on the host machine to
always supply a valid page table root, rather than properly validating
it along with the rest of the reloaded guest state."
http://sourceforge.net/tracker/?func=detail&atid=893831&aid=2687641&group_id=180599
Check for a valid cr3 address in kvm_arch_vcpu_ioctl_set_sregs, triple
fault in case of failure.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In the new mode instruction is decoded, but not executed. The EIP
is moved to point after the instruction.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is no need to skip instruction if the reason for a task switch
is a task gate in IDT and access to it is caused by an external even.
The problem is currently solved only for VMX since there is no reliable
way to skip an instruction in SVM. We should emulate it instead.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
A pte that is shadowed when the guest EFER.NXE=1 is not valid when
EFER.NXE=0; if bit 63 is set, the pte should cause a fault, and since the
shadow EFER always has NX enabled, this won't happen.
Fix by using a different shadow page table for different EFER.NXE bits. This
allows vcpus to run correctly with different values of EFER.NXE, and for
transitions on this bit to be handled correctly without requiring a full
flush.
Signed-off-by: Avi Kivity <avi@redhat.com>
Detect, indicate, and propagate page faults where reserved bits are set.
Take care to handle the different paging modes, each of which has different
sets of reserved bits.
[avi: fix pte reserved bits for efer.nxe=0]
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_vcpu_block() unhalts vpu on an interrupt/timer without checking
if interrupt window is actually opened.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently timer events are processed before entering guest mode. Move it
to main vcpu event loop since timer events should be processed even while
vcpu is halted. Timer may cause interrupt/nmi to be injected and only then
vcpu will be unhalted.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We ignore writes to the performance counters and performance event
selector registers already. Kaspersky antivirus reads the eventsel
MSR causing it to crash with the current behaviour.
Return 0 as data when the eventsel registers are read to stop the
crash.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
After discussion with Marcelo, we decided to rework device assignment framework
together. The old problems are kernel logic is unnecessary complex. So Marcelo
suggest to split it into a more elegant way:
1. Split host IRQ assign and guest IRQ assign. And userspace determine the
combination. Also discard msi2intx parameter, userspace can specific
KVM_DEV_IRQ_HOST_MSI | KVM_DEV_IRQ_GUEST_INTX in assigned_irq->flags to
enable MSI to INTx convertion.
2. Split assign IRQ and deassign IRQ. Import two new ioctls:
KVM_ASSIGN_DEV_IRQ and KVM_DEASSIGN_DEV_IRQ.
This patch also fixed the reversed _IOR vs _IOW in definition(by deprecated the
old interface).
[avi: replace homemade bitcount() by hweight_long()]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This issue just appeared in kvm-84 when running on 2.6.28.7 (x86-64)
with PREEMPT enabled.
We're getting syslog warnings like this many (but not all) times qemu
tells KVM to run the VCPU:
BUG: using smp_processor_id() in preemptible [00000000] code:
qemu-system-x86/28938
caller is kvm_arch_vcpu_ioctl_run+0x5d1/0xc70 [kvm]
Pid: 28938, comm: qemu-system-x86 2.6.28.7-mtyrel-64bit
Call Trace:
debug_smp_processor_id+0xf7/0x100
kvm_arch_vcpu_ioctl_run+0x5d1/0xc70 [kvm]
? __wake_up+0x4e/0x70
? wake_futex+0x27/0x40
kvm_vcpu_ioctl+0x2e9/0x5a0 [kvm]
enqueue_hrtimer+0x8a/0x110
_spin_unlock_irqrestore+0x27/0x50
vfs_ioctl+0x31/0xa0
do_vfs_ioctl+0x74/0x480
sys_futex+0xb4/0x140
sys_ioctl+0x99/0xa0
system_call_fastpath+0x16/0x1b
As it turns out, the call trace is messed up due to gcc's inlining, but
I isolated the problem anyway: kvm_write_guest_time() is being used in a
non-thread-safe manner on preemptable kernels.
Basically kvm_write_guest_time()'s body needs to be surrounded by
preempt_disable() and preempt_enable(), since the kernel won't let us
query any per-CPU data (indirectly using smp_processor_id()) without
preemption disabled. The attached patch fixes this issue by disabling
preemption inside kvm_write_guest_time().
[marcelo: surround only __get_cpu_var calls since the warning
is harmless]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The processor is documented to reload the PDPTRs while in PAE mode if any
of the CR4 bits PSE, PGE, or PAE change. Linux relies on this
behaviour when zapping the low mappings of PAE kernels during boot.
The code already handled changes to CR4.PAE; augment it to also notice changes
to PSE and PGE.
This triggered while booting an F11 PAE kernel; the futex initialization code
runs before any CR3 reloads and writes to a NULL pointer; the futex subsystem
ended up uninitialized, killing PI futexes and pulseaudio which uses them.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Some processors don't have EFER; don't oops if userspace wants us to
read EFER when we check NX.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
Properly unregister cpufreq notifier on onload if it was registered
during init.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Not releasing the time_page causes a leak of that page or the compound
page it is situated in.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: Make symbols static.
Fix this sparse warnings:
arch/x86/kvm/mmu.c:992:5: warning: symbol 'mmu_pages_add' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1124:5: warning: symbol 'mmu_pages_next' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1144:6: warning: symbol 'mmu_pages_clear_parents' was not declared. Should it be static?
arch/x86/kvm/x86.c:2037:5: warning: symbol 'kvm_read_guest_virt' was not declared. Should it be static?
arch/x86/kvm/x86.c:2067:5: warning: symbol 'kvm_write_guest_virt' was not declared. Should it be static?
virt/kvm/irq_comm.c:220:5: warning: symbol 'setup_routing_entry' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
IRQ injection status is either -1 (if there was no CPU found
that should except the interrupt because IRQ was masked or
ioapic was misconfigured or ...) or >= 0 in that case the
number indicates to how many CPUs interrupt was injected.
If the value is 0 it means that the interrupt was coalesced
and probably should be reinjected.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvmclock currently falls apart on machines without constant tsc.
This patch fixes it. Changes:
* keep tsc frequency in a per-cpu variable.
* handle kvmclock update using a new request flag, thus checking
whenever we need an update each time we enter guest context.
* use a cpufreq notifier to track frequency changes and force
kvmclock updates.
* send ipis to kick cpu out of guest context if needed to make
sure the guest doesn't see stale values.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
AMD K10 CPUs implement the FFXSR feature that gets enabled using
EFER. Let's check if the virtual CPU description includes that
CPUID feature bit and allow enabling it then.
This is required for Windows Server 2008 in Hyper-V mode.
v2 adds CPUID capability exposure
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently KVM has a static routing from GSI numbers to interrupts (namely,
0-15 are mapped 1:1 to both PIC and IOAPIC, and 16:23 are mapped 1:1 to
the IOAPIC). This is insufficient for several reasons:
- HPET requires non 1:1 mapping for the timer interrupt
- MSIs need a new method to assign interrupt numbers and dispatch them
- ACPI APIC mode needs to be able to reassign the PCI LINK interrupts to the
ioapics
This patch implements an interrupt routing table (as a linked list, but this
can be easily changed) and a userspace interface to replace the table. The
routing table is initialized according to the current hardwired mapping.
Signed-off-by: Avi Kivity <avi@redhat.com>
Some typos, comments, whitespace errors corrected in the cpuid code
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Certain clocks (such as TSC) in older 2.6 guests overaccount for lost
ticks, causing severe time drift. Interrupt reinjection magnifies the
problem.
Provide an option to disable it.
[avi: allow room for expansion in case we want to disable reinjection
of other timers]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we advertise MSR_VM_HSAVE_PA, userspace will attempt to read it
even on Intel. Implement fake support for this MSR to avoid the
warnings.
Signed-off-by: Avi Kivity <avi@redhat.com>
vmap() on guest pages hides those pages from the Linux mm for an extended
(userspace determined) amount of time. Get rid of it.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This commit change the name of emulator_read_std into kvm_read_guest_virt,
and add new function name kvm_write_guest_virt that allow writing into a
guest virtual address.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
VMX initializes the TSC offset for each vcpu at different times, and
also reinitializes it for vcpus other than 0 on APIC SIPI message.
This bug causes the TSC's to appear unsynchronized in the guest, even if
the host is good.
Older Linux kernels don't handle the situation very well, so
gettimeofday is likely to go backwards in time:
http://www.mail-archive.com/kvm@vger.kernel.org/msg02955.htmlhttp://sourceforge.net/tracker/index.php?func=detail&aid=2025534&group_id=180599&atid=893831
Fix it by initializating the offset of each vcpu relative to vm creation
time, and moving it from vmx_vcpu_reset to vmx_vcpu_setup, out of the
APIC MP init path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Don't allow a vcpu with cr4.pge cleared to use a shadow page created with
cr4.pge set; this might cause a cr3 switch not to sync ptes that have the
global bit set (the global bit has no effect if !cr4.pge).
This can only occur on smp with different cr4.pge settings for different
vcpus (since a cr4 change will resync the shadow ptes), but there's no
cost to being correct here.
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the remaining bits to make use of debug registers also for guest
debugging, thus enabling the use of hardware breakpoints and
watchpoints.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far KVM only had basic x86 debug register support, once introduced to
realize guest debugging that way. The guest itself was not able to use
those registers.
This patch now adds (almost) full support for guest self-debugging via
hardware registers. It refactors the code, moving generic parts out of
SVM (VMX was already cleaned up by the KVM_SET_GUEST_DEBUG patches), and
it ensures that the registers are properly switched between host and
guest.
This patch also prepares debug register usage by the host. The latter
will (once wired-up by the following patch) allow for hardware
breakpoints/watchpoints in guest code. If this is enabled, the guest
will only see faked debug registers without functionality, but with
content reflecting the guest's modifications.
Tested on Intel only, but SVM /should/ work as well, but who knows...
Known limitations: Trapping on tss switch won't work - most probably on
Intel.
Credits also go to Joerg Roedel - I used his once posted debugging
series as platform for this patch.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This rips out the support for KVM_DEBUG_GUEST and introduces a new IOCTL
instead: KVM_SET_GUEST_DEBUG. The IOCTL payload consists of a generic
part, controlling the "main switch" and the single-step feature. The
arch specific part adds an x86 interface for intercepting both types of
debug exceptions separately and re-injecting them when the host was not
interested. Moveover, the foundation for guest debugging via debug
registers is layed.
To signal breakpoint events properly back to userland, an arch-specific
data block is now returned along KVM_EXIT_DEBUG. For x86, the arch block
contains the PC, the debug exception, and relevant debug registers to
tell debug events properly apart.
The availability of this new interface is signaled by
KVM_CAP_SET_GUEST_DEBUG. Empty stubs for not yet supported archs are
provided.
Note that both SVM and VTX are supported, but only the latter was tested
yet. Based on the experience with all those VTX corner case, I would be
fairly surprised if SVM will work out of the box.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Userspace has to tell the kernel module somehow that nested SVM should be used.
The easiest way that doesn't break anything I could think of is to implement
if (cpuid & svm)
allow write to efer
else
deny write to efer
Old userspaces mask the SVM capability bit, so they don't break.
In order to find out that the SVM capability is set, I had to split the
kvm_emulate_cpuid into a finding and an emulating part.
(introduced in v6)
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Implement the hsave MSR, that gives the VCPU a GPA to save the
old guest state in.
v2 allows userspace to save/restore hsave
v4 dummys out the hsave MSR, so we use a host page
v6 remembers the guest's hsave and exports the MSR
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This is better.
Currently, this code path is posing us big troubles,
and we won't have a decent patch in time. So, temporarily
disable it.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In the past, kvm_get_kvm() and kvm_put_kvm() was called in assigned device irq
handler and interrupt_work, in order to prevent cancel_work_sync() in
kvm_free_assigned_irq got a illegal state when waiting for interrupt_work done.
But it's tricky and still got two problems:
1. A bug ignored two conditions that cancel_work_sync() would return true result
in a additional kvm_put_kvm().
2. If interrupt type is MSI, we would got a window between cancel_work_sync()
and free_irq(), which interrupt would be injected again...
This patch discard the reference count used for irq handler and interrupt_work,
and ensure the legal state by moving the free function at the very beginning of
kvm_destroy_vm(). And the patch fix the second bug by disable irq before
cancel_work_sync(), which may result in nested disable of irq but OK for we are
going to free it.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_arch_sync_events is introduced to quiet down all other events may happen
contemporary with VM destroy process, like IRQ handler and work struct for
assigned device.
For kvm_arch_sync_events is called at the very beginning of kvm_destroy_vm(), so
the state of KVM here is legal and can provide a environment to quiet down other
events.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is no point in doing the ready_for_nmi_injection/
request_nmi_window dance with user space. First, we don't do this for
in-kernel irqchip anyway, while the code path is the same as for user
space irqchip mode. And second, there is nothing to loose if a pending
NMI is overwritten by another one (in contrast to IRQs where we have to
save the number). Actually, there is even the risk of raising spurious
NMIs this way because the reason for the held-back NMI might already be
handled while processing the first one.
Therefore this patch creates a simplified user space NMI injection
interface, exporting it under KVM_CAP_USER_NMI and dropping the old
KVM_CAP_NMI capability. And this time we also take care to provide the
interface only on archs supporting NMIs via KVM (right now only x86).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the guest executes invlpg, peek into the pagetable and attempt to
prepopulate the shadow entry.
Also stop dirty fault updates from interfering with the fork detector.
2% improvement on RHEL3/AIM7.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Skip syncing global pages on cr3 switch (but not on cr4/cr0). This is
important for Linux 32-bit guests with PAE, where the kmap page is
marked as global.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The code to traverse the cpuid data array list for counting type of leaves is
currently broken.
This patches fixes the 2 things in it.
1. Set the 1st counting entry's flag KVM_CPUID_FLAG_STATE_READ_NEXT. Without
it the code will never find a valid entry.
2. Also the stop condition in the for loop while looking for the next unflaged
entry is broken. It needs to stop when it find one matching entry;
and in the case of count of 1, it will be the same entry found in this
iteration.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
For cpuid leaf 0xb the bits 8-15 in ECX register define the end of counting
leaf. The previous code was using bits 0-7 for this purpose, which is
a bug.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Ideally, every assigned device should in a clear condition before and after
assignment, so that the former state of device won't affect later work.
Some devices provide a mechanism named Function Level Reset, which is
defined in PCI/PCI-e document. We should execute it before and after device
assignment.
(But sadly, the feature is new, and most device on the market now don't
support it. We are considering using D0/D3hot transmit to emulate it later,
but not that elegant and reliable as FLR itself.)
[Update: Reminded by Xiantao, execute FLR after we ensure that the device can
be assigned to the guest.]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If we call the emulator we shouldn't call skip_emulated_instruction()
in the first place, since the emulator already computes the next rip
for us. Thus we move ->skip_emulated_instruction() out of
kvm_emulate_pio() and into handle_io() (and the svm equivalent). We
also replaced "return 0" by "break" in the "do_io:" case because now
the shadow register state needs to be committed. Otherwise eip will never
be updated.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
The effective memory type of EPT is the mixture of MSR_IA32_CR_PAT and memory
type field of EPT entry.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
GUEST_PAT support is a new feature introduced by Intel Core i7 architecture.
With this, cpu would save/load guest and host PAT automatically, for EPT memory
type in guest depends on MSR_IA32_CR_PAT.
Also add save/restore for MSR_IA32_CR_PAT.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Call kvm_arch_vcpu_reset() instead of directly using arch callback.
The function does additional things.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduces the KVM_NMI IOCTL to the generic x86 part of KVM for
injecting NMIs from user space and also extends the statistic report
accordingly.
Based on the original patch by Sheng Yang.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Ensure that a VCPU with pending NMIs is considered runnable.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
CPU reset invalidates pending or already injected NMIs, therefore reset
the related state variables.
Based on original patch by Gleb Natapov.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Every call of kvm_set_irq() should offer an irq_source_id, which is
allocated by kvm_request_irq_source_id(). Based on irq_source_id, we
identify the irq source and implement logical OR for shared level
interrupts.
The allocated irq_source_id can be freed by kvm_free_irq_source_id().
Currently, we support at most sizeof(unsigned long) different irq sources.
[Amit: - rebase to kvm.git HEAD
- move definition of KVM_USERSPACE_IRQ_SOURCE_ID to common file
- move kvm_request_irq_source_id to the update_irq ioctl]
[Xiantao: - Add kvm/ia64 stuff and make it work for kvm/ia64 guests]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (134 commits)
KVM: ia64: Add intel iommu support for guests.
KVM: ia64: add directed mmio range support for kvm guests
KVM: ia64: Make pmt table be able to hold physical mmio entries.
KVM: Move irqchip_in_kernel() from ioapic.h to irq.h
KVM: Separate irq ack notification out of arch/x86/kvm/irq.c
KVM: Change is_mmio_pfn to kvm_is_mmio_pfn, and make it common for all archs
KVM: Move device assignment logic to common code
KVM: Device Assignment: Move vtd.c from arch/x86/kvm/ to virt/kvm/
KVM: VMX: enable invlpg exiting if EPT is disabled
KVM: x86: Silence various LAPIC-related host kernel messages
KVM: Device Assignment: Map mmio pages into VT-d page table
KVM: PIC: enhance IPI avoidance
KVM: MMU: add "oos_shadow" parameter to disable oos
KVM: MMU: speed up mmu_unsync_walk
KVM: MMU: out of sync shadow core
KVM: MMU: mmu_convert_notrap helper
KVM: MMU: awareness of new kvm_mmu_zap_page behaviour
KVM: MMU: mmu_parent_walk
KVM: x86: trap invlpg
KVM: MMU: sync roots on mmu reload
...
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To share with other archs, this patch moves device assignment
logic to common parts.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM-x86 dumps a lot of debug messages that have no meaning for normal
operation:
- INIT de-assertion is ignored
- SIPIs are sent and received
- APIC writes are unaligned or < 4 byte long
(Windows Server 2003 triggers this on SMP)
Degrade them to true debug messages, keeping the host kernel log clean
for real problems.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The PIC code makes little effort to avoid kvm_vcpu_kick(), resulting in
unnecessary guest exits in some conditions.
For example, if the timer interrupt is routed through the IOAPIC, IRR
for IRQ 0 will get set but not cleared, since the APIC is handling the
acks.
This means that everytime an interrupt < 16 is triggered, the priority
logic will find IRQ0 pending and send an IPI to vcpu0 (in case IRQ0 is
not masked, which is Linux's case).
Introduce a new variable isr_ack to represent the IRQ's for which the
guest has been signalled / cleared the ISR. Use it to avoid more than
one IPI per trigger-ack cycle, in addition to the avoidance when ISR is
set in get_priority().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Allow guest pagetables to go out of sync. Instead of emulating write
accesses to guest pagetables, or unshadowing them, we un-write-protect
the page table and allow the guest to modify it at will. We rely on
invlpg executions to synchronize individual ptes, and will synchronize
the entire pagetable on tlb flushes.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
With pages out of sync invlpg needs to be trapped. For now simply nuke
the entry.
Untested on AMD.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The vcpu should process pending SIPI message before entering guest mode again.
kvm_arch_vcpu_runnable() returns true if the vcpu is in SIPI state, so
we can't call it here.
Signed-off-by: Gleb Natapov <gleb@qumranet.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Noticed by sparse:
arch/x86/kvm/x86.c:3591:5: warning: symbol 'kvm_load_realmode_segment' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Convert gfn_to_pfn to use get_user_pages_fast, which can do lockless
pagetable lookups on x86. Kernel compilation on 4-way guest is 3.7%
faster on VMX.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When an IRQ allocation fails, we free up the device structures and
disable the device so that we can unregister the device in the
userspace and not expose it to the guest at all.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Based on a patch by: Kay, Allen M <allen.m.kay@intel.com>
This patch enables PCI device assignment based on VT-d support.
When a device is assigned to the guest, the guest memory is pinned and
the mapping is updated in the VT-d IOMMU.
[Amit: Expose KVM_CAP_IOMMU so we can check if an IOMMU is present
and also control enable/disable from userspace]
Signed-off-by: Kay, Allen M <allen.m.kay@intel.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: Ben-Ami Yassour <benami@il.ibm.com>
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Since "KVM: x86: do not execute halted vcpus", HLT by vcpu0 before system
reset by the IO thread will hang the guest.
Mark vcpu as runnable in such case.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Offline or uninitialized vcpu's can be executed if requested to perform
userspace work.
Follow Avi's suggestion to handle halted vcpu's in the main loop,
simplifying kvm_emulate_halt(). Introduce a new vcpu->requests bit to
indicate events that promote state from halted to running.
Also standardize vcpu wake sites.
Signed-off-by: Marcelo Tosatti <mtosatti <at> redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently KVM implements MC0-MC4_MISC read support. When booting Linux this
results in KVM warnings in the kernel log when the guest tries to read
MC5_MISC. Fix this warnings with this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
sparse says:
arch/x86/kvm/x86.c:107:32: warning: symbol 'kvm_find_assigned_dev' was not declared. Should it be static?
arch/x86/kvm/i8254.c:225:6: warning: symbol 'kvm_pit_ack_irq' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Even though we don't share irqs at the moment, we should ensure
regular user processes don't try to allocate system resources.
We check for capability to access IO devices (CAP_SYS_RAWIO) before
we request_irq on behalf of the guest.
Noticed by Avi.
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The vcpu thread can be preempted after the guest_debug_pre() callback,
resulting in invalid debug registers on the new vcpu.
Move it inside the non-preemptable section.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
[sheng: fix KVM_GET_LAPIC using wrong size]
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
On my machine with gcc 3.4, kvm uses ~2k of stack in a few
select functions. This is mostly because gcc fails to
notice that the different case: statements could have their
stack usage combined. It overflows very nicely if interrupts
happen during one of these large uses.
This patch uses two methods for reducing stack usage.
1. dynamically allocate large objects instead of putting
on the stack.
2. Use a union{} member for all of the case variables. This
tricks gcc into combining them all into a single stack
allocation. (There's also a comment on this)
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Based on a patch from: Amit Shah <amit.shah@qumranet.com>
This patch adds support for handling PCI devices that are assigned to
the guest.
The device to be assigned to the guest is registered in the host kernel
and interrupt delivery is handled. If a device is already assigned, or
the device driver for it is still loaded on the host, the device
assignment is failed by conveying a -EBUSY reply to the userspace.
Devices that share their interrupt line are not supported at the moment.
By itself, this patch will not make devices work within the guest.
The VT-d extension is required to enable the device to perform DMA.
Another alternative is PVDMA.
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Ben-Ami Yassour <benami@il.ibm.com>
Signed-off-by: Weidong Han <weidong.han@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Netware writes to DEBUGCTL and reads from the DEBUGCTL and LAST*IP MSRs
without further checks and is really confused to receive a #GP during that.
To make it happy we should just make them stubs, which is exactly what SVM
already does.
Writes to DEBUGCTL that are vendor-specific are resembled to behave as if the
virtual CPU does not know them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we're emulating an instruction, either it will succeed, in which case
any previously queued exception will be spurious, or we will requeue the
same exception.
Signed-off-by: Avi Kivity <avi@qumranet.com>
As suggested by Avi, introduce accessors to read/write guest registers.
This simplifies the ->cache_regs/->decache_regs interface, and improves
register caching which is important for VMX, where the cost of
vmcs_read/vmcs_write is significant.
[avi: fix warnings]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows reading memslots with only the mmu_lock hold for mmu
notifiers that runs in atomic context and with mmu_lock held.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows the mmu notifier code to run unalias_gfn with only the
mmu_lock held. Only alias writes need the mmu_lock held. Readers will
either take the slots_lock in read mode or the mmu_lock.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is no guarantee that the old TSS descriptor in the GDT contains
the proper base address. This is the case for Windows installation's
reboot-via-triplefault.
Use guest registers instead. Also translate the address properly.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The segment base is always a linear address, so translate before
accessing guest memory.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Flush the shadow mmu before removing regions to avoid stale entries.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is no need to grab slots_lock if the vapic_page will not
be touched.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of prefetching all segment bases before emulation, read them at the
last moment. Since most of them are unneeded, we save some cycles on
Intel machines where this is a bit expensive.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we're not gonna do anything (case in which failure is already
reported), we do not need to even bother with calculating the linear rip.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables coalesced MMIO for x86 architecture.
It defines KVM_MMIO_PAGE_OFFSET and KVM_CAP_COALESCED_MMIO.
It enables the compilation of coalesced_mmio.c.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Modify member in_range() of structure kvm_io_device to pass length and the type
of the I/O (write or read).
This modification allows to use kvm_io_device with coalesced MMIO.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Prefixes functions that will be exported with kvm_.
We also prefixed set_segment() even if it still static
to be coherent.
signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add emulation for the memory type range registers, needed by VMware esx 3.5,
and by pci device assignment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
VMX hardware can cache the contents of a vcpu's vmcs. This cache needs
to be flushed when migrating a vcpu to another cpu, or (which is the case
that interests us here) when disabling hardware virtualization on a cpu.
The current implementation of decaching iterates over the list of all vcpus,
picks the ones that are potentially cached on the cpu that is being offlined,
and flushes the cache. The problem is that it uses mutex_trylock() to gain
exclusive access to the vcpu, which fires off a (benign) warning about using
the mutex in an interrupt context.
To avoid this, and to make things generally nicer, add a new per-cpu list
of potentially cached vcus. This makes the decaching code much simpler. The
list is vmx-specific since other hardware doesn't have this issue.
[andrea: fix crash on suspend/resume]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds some kvmtrace bits to the generic x86 code
where it is instrumented from SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Noticed by sparse:
arch/x86/kvm/vmx.c:1583:6: warning: symbol 'vmx_disable_intercept_for_msr' was not declared. Should it be static?
arch/x86/kvm/x86.c:3406:5: warning: symbol 'kvm_task_switch_16' was not declared. Should it be static?
arch/x86/kvm/x86.c:3429:5: warning: symbol 'kvm_task_switch_32' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1968:6: warning: symbol 'kvm_mmu_remove_one_alloc_mmu_page' was not declared. Should it be static?
arch/x86/kvm/mmu.c:2014:6: warning: symbol 'mmu_destroy_caches' was not declared. Should it be static?
arch/x86/kvm/lapic.c:862:5: warning: symbol 'kvm_lapic_get_base' was not declared. Should it be static?
arch/x86/kvm/i8254.c:94:5: warning: symbol 'pit_get_gate' was not declared. Should it be static?
arch/x86/kvm/i8254.c:196:5: warning: symbol '__pit_timer_fn' was not declared. Should it be static?
arch/x86/kvm/i8254.c:561:6: warning: symbol '__inject_pit_timer_intr' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If a timer fires after kvm_inject_pending_timer_irqs() but before
local_irq_disable() the code will enter guest mode and only inject such
timer interrupt the next time an unrelated event causes an exit.
It would be simpler if the timer->pending irq conversion could be done
with IRQ's disabled, so that the above problem cannot happen.
For now introduce a new vcpu requests bit to cancel guest entry.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A guest vcpu instance can be scheduled to a different physical CPU
between the test for KVM_REQ_MIGRATE_TIMER and local_irq_disable().
If that happens, the timer will only be migrated to the current pCPU on
the next exit, meaning that guest LAPIC timer event can be delayed until
a host interrupt is triggered.
Fix it by cancelling guest entry if any vcpu request is pending. This
has the side effect of nicely consolidating vcpu->requests checks.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Migrate the PIT timer to the physical CPU which vcpu0 is scheduled on,
similarly to what is done for the LAPIC timers, otherwise PIT interrupts
will be delayed until an unrelated event causes an exit.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This make sure not to schedule in atomic during fx_init. I also
changed the name of fpu_init to fx_finit to avoid duplicating the name
with fpu_init that is already used in the kernel, this makes grep
simpler if nothing else.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Clear pending exceptions when setting new register values. This avoids
spurious exceptions after restoring a vcpu state or after
reset-on-triple-fault.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
[aliguory: plug leak]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is a window open between testing of pending IRQ's
and assignment of guest_mode in __vcpu_run.
Injection of IRQ's can race with __vcpu_run as follows:
CPU0 CPU1
kvm_x86_ops->run()
vcpu->guest_mode = 0 SET_IRQ_LINE ioctl
..
kvm_x86_ops->inject_pending_irq
kvm_cpu_has_interrupt()
apic_test_and_set_irr()
kvm_vcpu_kick
if (vcpu->guest_mode)
send_ipi()
vcpu->guest_mode = 1
So move guest_mode=1 assignment before ->inject_pending_irq, and make
sure that it won't reorder after it.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
So userspace can save/restore the mpstate during migration.
[avi: export the #define constants describing the value]
[christian: add s390 stubs]
[avi: ditto for ia64]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Trace markers allow userspace to trace execution of a virtual machine
in order to monitor its performance.
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Unify slots_lock acquision around vcpu_run(). This is simpler and less
error-prone.
Also fix some callsites that were not grabbing the lock properly.
[avi: drop slots_lock while in guest mode to avoid holding the lock
for indefinite periods]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This emulates the x86 hardware task switch mechanism in software, as it is
unsupported by either vmx or svm. It allows operating systems which use it,
like freedos, to run as kvm guests.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Hypercall based pte updates are faster than faults, and also allow use
of the lazy MMU mode to batch operations.
Don't report the feature if two dimensional paging is enabled.
[avi:
- one mmu_op hypercall instead of one per op
- allow 64-bit gpa on hypercall
- don't pass host errors (-ENOMEM) to guest]
[akpm: warning fix on i386]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The patch moves the PIT model from userspace to kernel, and increases
the timer accuracy greatly.
[marcelo: make last_injected_time per-guest]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tested-and-Acked-by: Alex Davis <alex14641@yahoo.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
In the current inject_page_fault path KVM only checks if there is another PF
pending and injects a DF then. But it has to check for a pending DF too to
detect a shutdown condition in the VCPU. If this is not detected the VCPU goes
to a PF -> DF -> PF loop when it should triple fault. This patch detects this
condition and handles it with an KVM_SHUTDOWN exit to userspace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Create large pages mappings if the guest PTE's are marked as such and
the underlying memory is hugetlbfs backed. If the largepage contains
write-protected pages, a large pte is not used.
Gives a consistent 2% improvement for data copies on ram mounted
filesystem, without NPT/EPT.
Anthony measures a 4% improvement on 4-way kernbench, with NPT.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Mark zapped root pagetables as invalid and ignore such pages during lookup.
This is a problem with the cr3-target feature, where a zapped root table fools
the faulting code into creating a read-only mapping. The result is a lockup
if the instruction can't be emulated.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
In two case statements, use the ever popular 'i' instead of index:
arch/x86/kvm/x86.c:1063:7: warning: symbol 'index' shadows an earlier one
arch/x86/kvm/x86.c:1000:9: originally declared here
arch/x86/kvm/x86.c:1079:7: warning: symbol 'index' shadows an earlier one
arch/x86/kvm/x86.c:1000:9: originally declared here
Make it static.
arch/x86/kvm/x86.c:1945:24: warning: symbol 'emulate_ops' was not declared. Should it be static?
Drop the return statements.
arch/x86/kvm/x86.c:2878:2: warning: returning void-valued expression
arch/x86/kvm/x86.c:2944:2: warning: returning void-valued expression
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This is the host part of kvm clocksource implementation. As it does
not include clockevents, it is a fairly simple implementation. We
only have to register a per-vcpu area, and start writing to it periodically.
The area is binary compatible with xen, as we use the same shadow_info
structure.
[marcelo: fix bad_page on MSR_KVM_SYSTEM_TIME]
[avi: save full value of the msr, even if enable bit is clear]
[avi: clear previous value of time_page]
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The load_pdptrs() function is required in the SVM module for NPT support.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch makes the EFER register accessible on a 32bit KVM host. This is
necessary to boot 32 bit PAE guests under SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch aligns the bits the guest can set in the EFER register with the
features in the host processor. Currently it lets EFER.NX disabled if the
processor does not support it and enables EFER.LME and EFER.LMA only for KVM on
64 bit hosts.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch give the SVM and VMX implementations the ability to add some bits
the guest can set in its EFER register.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch replaces the mmap_sem lock for the memory slots with a new
kvm private lock, it is needed beacuse untill now there were cases where
kvm accesses user memory while holding the mmap semaphore.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Injecting an GP when accessing this MSR lets Windows crash when running some
stress test tools in KVM. So this patch emulates access to this MSR.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
One of the use cases for the supported cpuid list is to create a "greatest
common denominator" of cpu capabilities in a server farm. As such, it is
useful to be able to get the list without creating a virtual machine first.
Since the code does not depend on the vm in any way, all that is needed is
to move it to the device ioctl handler. The capability identifier is also
changed so that binaries made against -rc1 will fail gracefully.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Whilst working on getting a VM to initialize in to IA32e mode I found
this issue. set_cr0 relies on comparing the old cr0 to the new one to
work correctly. Move the assignment below so the compare can work.
Signed-off-by: Paul Knowles <paul@transitive.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
arch/x86/kvm/x86.c: In function 'emulator_cmpxchg_emulated':
arch/x86/kvm/x86.c:1746: warning: passing argument 2 of 'vcpu->arch.mmu.gva_to_gpa' makes integer from pointer without a cast
arch/x86/kvm/x86.c:1746: warning: 'addr' is used uninitialized in this function
Is true. Local variable `addr' shadows incoming arg `addr'. Avi is on
vacation for a while, so...
Cc: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Migrating the apic timer in the critical section is not very nice, and is
absolutely horrible with the real-time port. Move migration to the regular
vcpu execution path, triggered by a new bitflag.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When preparing to enter the guest, if an interrupt comes in while
preemption is disabled but interrupts are still enabled, we miss a
preemption point. Fix by explicitly checking whether we need to
reschedule.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Otherwise we re-initialize the mmu caches, which will fail since the
caches are already registered, which will cause us to deinitialize said caches.
Signed-off-by: Avi Kivity <avi@qumranet.com>
When executing a test program called "crashme", we found the KVM guest cannot
survive more than ten seconds, then encounterd kernel panic. The basic concept
of "crashme" is generating random assembly code and trying to execute it.
After some fixes on emulator insn validity judgment, we found it's hard to
get the current emulator handle the invalid instructions correctly, for the
#UD trap for hypercall patching caused troubles. The problem is, if the opcode
itself was OK, but combination of opcode and modrm_reg was invalid, and one
operand of the opcode was memory (SrcMem or DstMem), the emulator will fetch
the memory operand first rather than checking the validity, and may encounter
an error there. For example, ".byte 0xfe, 0x34, 0xcd" has this problem.
In the patch, we simply check that if the invalid opcode wasn't vmcall/vmmcall,
then return from emulate_instruction() and inject a #UD to guest. With the
patch, the guest had been running for more than 12 hours.
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Do not hold kvm->lock mutex across the entire pagefault code,
only acquire it in places where it is necessary, such as mmu
hash list, active list, rmap and parent pte handling.
Allow concurrent guest walkers by switching walk_addr() to use
mmap_sem in read-mode.
And get rid of the lockless __gfn_to_page.
[avi: move kvm_mmu_pte_write() locking inside the function]
[avi: add locking for real mode]
[avi: fix cmpxchg locking]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This adds a mechanism for exposing the virtual apic tpr to the guest, and a
protocol for letting the guest update the tpr without causing a vmexit if
conditions allow (e.g. there is no interrupt pending with a higher priority
than the new tpr).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add a facility to report on accesses to the local apic tpr even if the
local apic is emulated in the kernel. This is basically a hack that
allows userspace to patch Windows which tends to bang on the tpr a lot.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This can help diagnosing what the guest is trying to do. In many cases
we can get away with partial emulation of msrs.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Moving kvm_vcpu_kick() to x86.c. Since it should be
common for all archs, put its declarations in <linux/kvm_host.h>
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This paves the way for multiple architecture support. Note that while
ioapic.c could potentially be shared with ia64, it is also moved.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Avi Kivity
