Adding visibility of resource usage of QPs, CQs and counters used by
virtual functions. This feature will be used to give the PF administrator
more data while debugging VF status. Usage info was added to ALLOC_RES
command, to notify the PF if the resource which is being reserved or
allocated for the VF will be used by kernel driver or by user verbs.
Updated reservation and allocation functions of QP, CQ and counter with
additional usage parameter.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When inline-receive is enabled, the HCA may write received
data into the receive WQE.
Inline-receive is enabled by setting its matching bit in
the QP context and each single-packet message with payload
not exceeding the receive WQE size will be delivered to
the WQE.
The completion report will indicate that the payload was placed to the WQE.
It includes:
1) Return maximum supported size of inline-receive by the hardware
in query_device vendor's data part.
2) Enable the feature when requested by the vendor data input.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds below requester and responder side error counters,
which will be exposed by hardware counters interface and are supported
as part of query Q counters command extension.
+---------------------------+-------------------------------------+
| Name | Description |
|---------------------------+-------------------------------------|
|resp_local_length_error | Number of times responder detected |
| | local length errors |
|---------------------------+-------------------------------------|
|resp_cqe_error | Number of CQEs completed with error |
| | at responder |
|---------------------------+-------------------------------------|
|req_cqe_error | Number of CQEs completed with error |
| | at requester |
|---------------------------+-------------------------------------|
|req_remote_invalid_request | Number of times requester detected |
| | remote invalid request error |
|---------------------------+-------------------------------------|
|req_remote_access_error | Number of times requester detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_remote_access_error | Number of times responder detected |
| | remote access error |
|---------------------------+-------------------------------------|
|resp_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at responder |
|---------------------------+-------------------------------------|
|req_cqe_flush_error | Number of CQEs completed with |
| | flushed with error at requester |
+---------------------------+-------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.
Fixes: 17d2f88f92 ("IB/mlx5: Add ODP atomics support")
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When we have a miss in one order of the mkey cache, we try to get
an mkey from a higher order.
We still need to check that the higher order can be used with UMR
before using it. Otherwise, we will get an mkey with 0 entries and
the post send operation that is used to fill it will complete with
the following error:
mlx5_0:dump_cqe:275:(pid 0): dump error cqe
00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000000 0f007806 25000025 49ce59d2
Fixes: 49780d42df ("IB/mlx5: Expose MR cache for mlx5_ib")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Report RX checksum capabilities when 'ipoib_enhanced_offloads'
capabilities are set and support checksum.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to add multicast flow steering support, there is need
to block the attaching of mcg flow for underlay QP, recognize
multicast IB_FLOW_SPEC_IPV4 based on its IP and enable
creating/destroying flow for IB layer.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Allow user space applications to accelerate send and receive
traffic which is typically handled by IPoIB ULP by creating
a UD QP with a given source QPN of the IPoIB UD QP.
UD QP with a given source QPN should basically be similar to
RAW QP from point of view of its created resources.
However,
- Its TIS should point to the source QPN.
- Modify can be done only on its state as the transport attributes
are managed by its source QP.
This patch manages below:
- Creating/destroying/modifying UD QP with a given source QPN.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable QP creation with a given source QP number, the created QP will
use the source QPN as its wire QP number.
To create such a QP, root privileges (i.e. CAP_NET_RAW) are required
from the user application.
This comes as a pre-patch for downstream patches in this series to
allow user space applications to accelerate traffic which is typically
handled by IPoIB ULP.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When creating address handle from multicast GID, set MAC according to
the appropriate formula instead of searching for it in the GID table:
- For IPv4 multicast GID use ip_eth_mc_map().
- For IPv6 multicast GID use ipv6_eth_mc_map().
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RoCEv2 Annex states that for RoCEv2 over IPv4, the corresponding
IPv4 address is encoded into the GID according to the following rule:
GID= :ffff:<IPv4 address>
Remove the 0xff0e prefix for RoCEv2 packets with IPv4 and leave it
zeroed and change rdma_is_multicast_addr() to consider the new logic.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RoCE Annex (A16.9.10/11) declares that during attach (detach) QP to a
multicast group, if the QP is associated with a RoCE port, the
multicast group MLID is unused and is ignored.
During attach or detach multicast, when the QP is associated with a
port, it is enough to check the port's link layer and validate the
LID only if it is Infiniband. Otherwise, avoid validating the
multicast LID.
Fixes: 8561eae60f ("IB/core: For multicast functions, verify that LIDs are multicast LIDs")
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add debugfs interface for monitor the number of delay drop timeout
events and the number of existing dropless RQs in the system.
In addition add debugfs interface for configuring the global timeout value
which is used in the SET_DELAY_DROP command.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQs that were configured for "delay drop" will prevent packet drops
when their WQEs are depleted.
Marking an RQ to be drop-less is done by setting delay_drop_en in RQ
context using CREATE_RQ command.
Since this feature is globally activated/deactivated by using the
SET_DELAY_DROP command on all the marked RQs, we activated/deactivated
it according to the number of RQs with 'delay_drop' enabled.
When timeout is expired, then the feature is deactivated. Therefore
the driver handles the delay drop timeout event and reactivate it.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When a user sets port_guid, node_guid or policy of an IB virtual
function, save this information in "struct mlx5_vf_context".
This information will be restored later when pci_resume is called.
To make sure this works, one can use aer-inject to generate PCI
errors on mlx5 devices and verify if relevant fields are restored
after PCI resume.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds debug control parameters for congestion control which
can be read or written through debugfs. They are for reaction point and
notification point nodes.
These control parameters are as below:
+------------------------------+-----------------------------------------+
| Name | Description |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate | When set target rate is updated to |
| | current rate |
|------------------------------+-----------------------------------------|
|rp_clamp_tgt_rate_ati | When set update target rate based on |
| | timer as well |
|------------------------------+-----------------------------------------|
|rp_time_reset | time between rate increase if no |
| | CNP is received unit in usec |
|------------------------------+-----------------------------------------|
|rp_byte_reset | Number of bytes between rate inease if |
| | no CNP is received |
|------------------------------+-----------------------------------------|
|rp_threshold | Threshold for reaction point rate |
| | control |
|------------------------------+-----------------------------------------|
|rp_ai_rate | Rate for target rate, unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_hai_rate | Rate for hyper increase state |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_min_dec_fac | Minimum factor by which the current |
| | transmit rate can be changed when |
| | processing a CNP, unit is percerntage |
|------------------------------+-----------------------------------------|
|rp_min_rate | Minimum value for rate limit, |
| | unit in Mbps |
|------------------------------+-----------------------------------------|
|rp_rate_to_set_on_first_cnp | Rate that is set when first CNP is |
| | received, unit is Mbps |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_g | Used to calculate alpha |
|------------------------------+-----------------------------------------|
|rp_dce_tcp_rtt | Time between updates of alpha value, |
| | unit is usec |
|------------------------------+-----------------------------------------|
|rp_rate_reduce_monitor_period | Minimum time between consecutive rate |
| | reductions |
|------------------------------+-----------------------------------------|
|rp_initial_alpha_value | Initial value of alpha |
|------------------------------+-----------------------------------------|
|rp_gd | When CNP is received, flow rate is |
| | reduced based on gd, rp_gd is given as |
| | log2(rp_gd) |
|------------------------------+-----------------------------------------|
|np_cnp_dscp | dscp code point for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio_mode | 802.1p priority for generated cnp |
|------------------------------+-----------------------------------------|
|np_cnp_prio | cnp priority mode |
+------------------------------+-----------------------------------------+
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The old logic ignored link state. This led to missing IB events like
when link goes down on the switch while admin state is up or to redundant
events like when admin state goes up while link is down.
To fix that, probe the port state on NETDEV events and compare to last
known state to decide if IB events needs to be dispatched.
FIxes: 5ec8c83e3a ("IB/mlx5: Port events in RoCE now rely on netdev events")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Currently, unicast/multicast loopback raw ethernet
(non-RDMA) packets are sent back to the vport.
A unicast loopback packet is the packet with destination
MAC address the same as the source MAC address.
For multicast, the destination MAC address is in the
vport's multicast filter list.
Moreover, the local loopback is not needed if
there is one or none user space context.
After this patch, the raw ethernet unicast and multicast
local loopback are disabled by default. When there is more
than one user space context, the local loopback is enabled.
Note that when local loopback is disabled, raw ethernet
packets are not looped back to the vport and are forwarded
to the next routing level (eswitch, or multihost switch,
or out to the wire depending on the configuration).
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Initialize the port_num for iWARP in rdma_init_qp_attr.
Fixes: 5ecce4c9b17b("Check port number supplied by user verbs cmds")
Cc: <stable@vger.kernel.org> # v2.6.14+
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The port number is only valid if IB_QP_PORT is set in the mask.
So only check port number if it is valid to prevent modify_qp from
failing due to an invalid port number.
Fixes: 5ecce4c9b17b("Check port number supplied by user verbs cmds")
Cc: <stable@vger.kernel.org> # v2.6.14+
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We might get some bogus error completions in case the target will
remotely invalidate the rkey and the HCA will need to retransmit
from this buffer.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If we modified the qp to ERROR state, and
drained the recieve queue, post_recv must
trigger the responder task to complete
the drain work request.
Cc: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>--
Signed-off-by: Doug Ledford <dledford@redhat.com>
Wrap ib_copy_to_udata with a function that ensures that the data
being copied over to user space isn't longer than the allowed.
Fixes: cecbcddf64 ("qedr: Add support for QP verbs")
Fixes: a7efd7773e ("qedr: Add support for PD,PKEY and CQ verbs")
Fixes: ac1b36e55a ("qedr: Add support for user context verbs")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Only use the read sge lkey/addr and the remote rkey/addr if the
length of the read is not zero. Otherwise the read response might
be treated as the RTR read response and not delivered to the
application. Or worse Terminator hardware will fail a 0B read
if the STAG is 0 even if the read length is 0.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
CM REQs cannot be successfully retried, because a new pv_cm_id is
created for each request, without checking if one already exists.
By checking if an id exists before creating one, the bug is fixed.
This bug can be provoked by running an RDMA CM user-land application,
but inserting a five seconds delay before the rdma_accept() call on
the passive side. This delay is larger than the default CMA timeout,
and triggers a retry from the active side. The retried REQ will use
another pv_cm_id (the cm_id on the wire). This confuses the CM
protocol and two REJs are sent from the passive side.
Here is an excerpt from ibdump running without the patch:
3.285092 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382711 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.382861 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
7.387644 LID: 4 -> LID: 4 InfiniBand 290 CM: ConnectReject
and here is the same with bug fix applied:
3.251010 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
7.349387 LID: 4 -> LID: 4 SDP 290 CM: ConnectRequest(SDP Hello)
8.258443 LID: 4 -> LID: 4 SDP 290 CM: ConnectReply(SDP Hello)
8.259890 LID: 4 -> LID: 4 InfiniBand 290 CM: ReadyToUse
Suggested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reported-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Tested-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current computation of qp->timeout_jiffies in rvt_modify_qp() will cause
overflow due to the fact that the input to the function usecs_to_jiffies
is only 32-bit ( unsigned int). Overflow will occur when attr->timeout is
equal to or greater than 30. The consequence is unnecessarily excessive
retry and thus degradation of the system performance.
This patch fixes the problem by limiting the input to 5-bit and calling
usecs_to_jiffies() before multiplying the scaling factor.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Local ack delay exposed by the driver is 0 which means infinite QP
timeout. Reporting the default value to 16 (approx 260ms)
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
While invoking the req_notify_cq hook, ULPs can request
whether the CQs have any CQEs pending. If CQEs are pending,
drivers can indicate it by returning 1 for req_notify_cq.
The stack will poll CQ again till CQ is empty.
This patch peeks the CQ for any valid entries and return accordingly.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Fix the incorrect reporting of number of polled
entries by taking into account the max CQ depth
in the driver.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Driver shall check if the host system bios has enabled
Atomic operations capability in PCI Device Control 2
register of the pci-device. Expose the ATOMIC_HCA
flag only if the Atomic operations capability is set.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Starting FW version 20.6.47, firmware is keeping separate statistics
for L2 and RDMA. However, driver needs to specify RDMA or not when
allocating stat_ctx.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There's a couple of bugs in the support of max_rd_atomic and
max_dest_rd_atomic. In the modify_qp, if the requested max_rd_atomic,
which is the ORRQ size, is greater than what the chip can support,
then we have to cap the request to chip max as we can't have the HW
overflow the ORRQ. Capping the max_rd_atomic support internally is okay
to do as the remaining read/atomic WRs will still be sitting in the SQ.
However, for the max_dest_rd_atomic, the driver has to error out as
this dictates the IRRQ size and we can't control what the remote
side sends.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
- Report supported value for max_mr_size to IB stack in query_device.
Also, check and log if MR size requested by application in
reg_user_mr() is greater than value currently supported by driver.
- Report only 4K page size support for now
- Fix Max_QP value returned by ibv_devinfo -vv.
In case of PF, FW reserves 129 QPs for creating QP1s of VFs
and PF. So the max_qp value reported by FW for PF doesn'tt include
the QP1. Fixing this issue by adding 1 with the value reported
by FW.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This fix is added only to avoid system crash in some a
specific scenario. When bnxt_re driver is loaded and if
user tries to change interface mac address, delete GID
fails because QP1 is still associated with existing MAC
(default GID). If the above command fails GID tables are
not modified in the h/w or driver, but the GID context memory
is freed. Now, if the user changes the mac back to the original
value, another add_gid comes to the driver where the driver
reports that the GID is already present in its table
and tries to access the context which was already freed.
So, in this case, in order to avoid NULL pointer de-reference,
this patch removes the context memory free if delete_gid fails
and the same context memory is re-used in new add_gid.
Memory cleanup will be taken care during driver unload, while
deleting the GID table.
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Posting WQE size of 2 results in a WQE_FORMAT_ERROR
thrown by the HW as it requires host to supply WQE Size with room
for atleast one SGE so that the resulting WQE size be atleast 3.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The driver must free the DPI during the dealloc_ucontext
instead of freeing it during dealloc_pd. However, the DPI
allocation scheme remains unchanged.
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
"umem" is a valid pointer. We intended to print "*umem" or even just
"err" instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If either of these allocations fail then we return ERR_PTR(0). That's
equivalent to NULL and results in a NULL pointer dereference in the
caller.
Fixes: fe2caefcdf ("RDMA/ocrdma: Add driver for Emulex OneConnect IBoE RDMA adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We should preserve the original "status" error code instead of resetting
it to zero. Returning ERR_PTR(0) is the same as NULL and results in a
NULL dereference in the callers. I added a printk() on error instead.
Fixes: 45e86b33ec ("RDMA/ocrdma: Cache recv DB until QP moved to RTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally don't set the error code on some error paths. It means
return ERR_PTR(0) which is NULL and results in a NULL dereference in the
caller.
Fixes: 13a239330a ("RDMA/cxgb3: Don't ignore insert_handle() failures")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If one of these kmalloc() calls fails then we return ERR_PTR(0) which is
NULL. It results in a NULL dereference in the callers.
Fixes: cfdda9d764 ("RDMA/cxgb4: Add driver for Chelsio T4 RNIC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally forgot to set the error code if ib_copy_from_udata()
fails. It means we return ERR_PTR(0) which is NULL and results in a
NULL dereference in the callers.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We accidentally don't see the error code on some of these error paths.
It means we return ERR_PTR(0) which is NULL and it results in a NULL
dereference in the caller.
This bug dates to pre-git days.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the physical buffer list entries (PBLEs) of a QP are freed
up at i40iw_dereg_mr, they can be assigned to a newly
created QP before the previous QP is destroyed. Fix this
by freeing PBLEs only when the QP is destroyed.
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Control Queue Pair (CQP) request objects, which have
not received a completion upon interface close, remain
in memory.
To fix this, identify and free all pending CQP request
objects during destroy CQP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To avoid infinite loop, in i40iw_ieq_handle_exception, update
plist inside while loop.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add missing write memory barrier before writing the
header containing valid bit to the WQE in i40iw_puda_send.
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current flow leaves software QP structures in memory if
Control Queue Pair (CQP) destroy QP OP fails. To fix this,
free QP resources on fail of CQP destroy QP OP.
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Moshe Shemesh