raid_status() wasn't emitting rebuild flags on the table line properly
because the rdev number was not yet set properly; index raid component
devices array directly to solve.
Also fix wrong argument count on emitted table line caused by 1 too
many rebuild/write_mostly argument and consider any journal_(dev|mode)
pairs.
Link: https://bugzilla.redhat.com/1782045
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When building with Clang + -Wtautological-constant-compare:
drivers/md/dm-raid.c:619:8: warning: converting the result of '<<' to a
boolean always evaluates to true [-Wtautological-constant-compare]
r = !RAID10_OFFSET;
^
drivers/md/dm-raid.c:517:28: note: expanded from macro 'RAID10_OFFSET'
#define RAID10_OFFSET (1 << 16) /* stripes with data
copies area adjacent on devices */
^
1 warning generated.
Negating a non-zero number will always make it zero, which is the
default value of r in this function so this statement is unnecessary;
remove it so that clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/753
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pass already deciphered state into rs_get_progress, simplify recovery offset
definition and combine two st_resync, st_reshape conditionals into one as is
already the case with st_check and st_repair.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
rs_setup_recovery() sets the starting recovery offset.
Drop superfluous rs_setup_recovery() and replace with __rs_setup_recovery().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This fixes a flaw causing raid set extensions not to be synchronized
in case the MD bitmap resize required additional pages to be allocated.
Also share resize code in the raid constructor between
new size changes and those occuring during recovery.
Bump the target version to define the change and document
it in Documentation/admin-guide/device-mapper/dm-raid.rst.
Reported-by: Steve D <steved424@gmail.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add a size argument to rs_set_dev_and_array_sectors as prerequisite
to fixing grown device resynchronization not occuring when new MD
bitmap pages have to be allocated as a result of the extension in
a follwup patch.
Also avoid code duplication by using rs_set_rdev_sectors
in the aforementioned function.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Unit of 'chunk_size' is byte, instead of sector, so fix it by setting
the queue_limits' max_discard_sectors to rs->md.chunk_sectors. Also,
rename chunk_size to chunk_size_bytes.
Without this fix, too big max_discard_sectors is applied on the request
queue of dm-raid, finally raid code has to split the bio again.
This re-split done by raid causes the following nested clone_endio:
1) one big bio 'A' is submitted to dm queue, and served as the original
bio
2) one new bio 'B' is cloned from the original bio 'A', and .map()
is run on this bio of 'B', and B's original bio points to 'A'
3) raid code sees that 'B' is too big, and split 'B' and re-submit
the remainded part of 'B' to dm-raid queue via generic_make_request().
4) now dm will handle 'B' as new original bio, then allocate a new
clone bio of 'C' and run .map() on 'C'. Meantime C's original bio
points to 'B'.
5) suppose now 'C' is completed by raid directly, then the following
clone_endio() is called recursively:
clone_endio(C)
->clone_endio(B) #B is original bio of 'C'
->bio_endio(A)
'A' can be big enough to make hundreds of nested clone_endio(), then
stack can be corrupted easily.
Fixes: 61697a6abd ("dm: eliminate 'split_discard_bios' flag from DM target interface")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If rs_prepare_reshape() fails, no cleanup is executed, leading to
leak of the raid_set structure allocated at the beginning of
raid_ctr(). To fix this issue, go to the label 'bad' if the error
occurs.
Fixes: 11e4723206 ("dm raid: stop keeping raid set frozen altogether")
Cc: stable@vger.kernel.org
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The DM support describes lots of aspects related to mapped
disk partitions from the userspace PoV.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The conversion is actually:
- add blank lines and indentation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
There is no need to have DM core split discards on behalf of a DM target
now that blk_queue_split() handles splitting discards based on the
queue_limits. A DM target just needs to set max_discard_sectors,
discard_granularity, etc, in queue_limits.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Sending a check/repair message infrequently leads to -EBUSY instead of
properly identifying an active resync. This occurs because
raid_message() is testing recovery bits in a racy way.
Fix by calling decipher_sync_action() from raid_message() to properly
identify the idle state of the RAID device.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
With raid4/5/6, journal device and write intent bitmap are mutually exclusive.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
With gcc-4.1.2:
drivers/md/dm-raid.c:3357: warning: type qualifiers ignored on function return type
Remove the "const" keyword to fix this.
Fixes: 36a240a706 ("dm raid: fix RAID leg rebuild errors")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Bump target version to reflect the documented fixes are available.
Also fix some code comments (typos and clarity).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On fast devices such as NVMe, a flaw in rs_get_progress() results in
false target status output when userspace lvm2 requests leg rebuilds
(symptom of the failure is device health chars 'aaaaaaaa' instead of
expected 'aAaAAAAA' causing lvm2 to fail).
The correct sync action state definitions already exist in
decipher_sync_action() so fix rs_get_progress() to use it.
Change decipher_sync_action() to return an enum rather than a string for
the sync states and call it from rs_get_progress(). Introduce
sync_str() to translate from enum to the string that is needed by
raid_status().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Update superblock when particular devices are requested via rebuild
(e.g. lvconvert --replace ...) to avoid spurious failure with the "New
device injected into existing raid set without 'delta_disks' or
'rebuild' parameter specified" error message.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When initiating a stripe adding reshape, a deadlock between
md_stop_writes() waiting for the sync thread to stop and the running
sync thread waiting for inactive stripes occurs (this frequently happens
on single-core but rarely on multi-core systems).
Fix this deadlock by setting MD_RECOVERY_WAIT to have the main MD
resynchronization thread worker (md_do_sync()) bail out when initiating
the reshape via constructor arguments.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Loading a new mapping table, the dm-raid target's constructor
retrieves the volatile reshaping state from the raid superblocks.
When the new table is activated in a following resume, the actual
reshape position is retrieved. The reshape driven by the previous
mapping can already have finished on small and/or fast devices thus
updating raid superblocks about the new raid layout.
This causes the actual array state (e.g. stripe size reshape finished)
to be inconsistent with the one in the new mapping, causing hangs with
left behind devices.
This race does not occur with usual raid device sizes but with small
ones (e.g. those created by the lvm2 test suite).
Fix by no longer transferring stale/inconsistent raid_set state during
preresume.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull input updates from Dmitry Torokhov:
- a new driver for Rohm BU21029 touch controller
- new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free
- updates to Atmel, eeti. pxrc and iforce drivers
- assorted driver cleanups and fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
MAINTAINERS: Add PhoenixRC Flight Controller Adapter
Input: do not use WARN() in input_alloc_absinfo()
Input: mark expected switch fall-throughs
Input: raydium_i2c_ts - use true and false for boolean values
Input: evdev - switch to bitmap API
Input: gpio-keys - switch to bitmap_zalloc()
Input: elan_i2c_smbus - cast sizeof to int for comparison
bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
md: Avoid namespace collision with bitmap API
dm: Avoid namespace collision with bitmap API
Input: pm8941-pwrkey - add resin entry
Input: pm8941-pwrkey - abstract register offsets and event code
Input: iforce - reorganize joystick configuration lists
Input: atmel_mxt_ts - move completion to after config crc is updated
Input: atmel_mxt_ts - don't report zero pressure from T9
Input: atmel_mxt_ts - zero terminate config firmware file
Input: atmel_mxt_ts - refactor config update code to add context struct
Input: atmel_mxt_ts - config CRC may start at T71
Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
...
bitmap API (include/linux/bitmap.h) has 'bitmap' prefix for its methods.
On the other hand MD bitmap API is special case.
Adding 'md' prefix to it to avoid name space collision.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A newly introduced function has 'const int' as the return type,
but as "make W=1" reports, that has no meaning:
drivers/md/dm-raid.c:510:18: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
This changes the return type to plain 'int'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 33e53f0685 ("dm raid: introduce extended superblock and new raid types to support takeover/reshaping")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fixes: 552aa679f2 ("dm raid: use rs_is_raid*()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
parse_raid_params() compares variable "int value" with INT_MAX.
E.g. related Coverity report excerpt:
CID 1364818 (#2 of 3): Operands don't affect result (CONSTANT_EXPRESSION_RESULT) [select issue]
1433 if (value > INT_MAX) {
Fix by changing checks to avoid INT_MAX.
Whilst on it, avoid unnecessary checks against constants
and add check for sane recovery speed min/max.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix a race for "nosync" activations providing "aa.." device health
characters and "0/N" sync ratio rather than "AA..." and "N/N". Occurs
when status for the raid set is retrieved during resume before the MD
sync thread starts and clears the MD_RECOVERY_NEEDED flag.
Cc: stable@vger.kernel.org # 4.16+
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Could be useful for a target to return stats or other information.
If a target does DMEMIT() anything to @result from its .message method
then it must return 1 to the caller.
Signed-off-By: Mike Snitzer <snitzer@redhat.com>
Upstream commit 4102d9de6d ("dm raid: fix rs_get_progress()
synchronization state/ratio") in combination with commit 7c29744ecc
("dm raid: simplify rs_get_progress()") introduced a regression by
incorrectly reporting a sync_ratio of 0 for degraded raid sets. This
caused lvm2 to fail to repair raid legs automatically.
Fix by identifying the degraded state by checking the MD_RECOVERY_INTR
flag and returning mddev->recovery_cp in case it is set.
MD sets recovery = [ MD_RECOVERY_RECOVER MD_RECOVERY_INTR
MD_RECOVERY_NEEDED ] when a RAID member fails. It then shuts down any
sync thread that is running and leaves us with all MD_RECOVERY_* flags
cleared. The bug occurs if a status is requested in the short time it
takes to shut down any sync thread and clear the flags, because we were
keying in on the MD_RECOVERY_NEEDED - understanding it to be the initial
phase of a “recover” sync thread. However, this is an incorrect
interpretation if MD_RECOVERY_INTR is also set.
This also explains why the bug only happened when automatic repair was
enabled and not a normal ‘manual’ method. It is impossible to react
quick enough to hit the problematic window without it being automated.
Fix passes automatic repair tests.
Fixes: 7c29744ecc ("dm raid: simplify rs_get_progress()")
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
walk; this is critical to allow forward progress without the need to
use the bioset's BIOSET_NEED_RESCUER.
- Remove DM core's BIOSET_NEED_RESCUER based dm_offload infrastructure.
- DM core cleanups and improvements to make bio-based DM more efficient
(e.g. reduced memory footprint as well leveraging per-bio-data more).
- Introduce new bio-based mode (DM_TYPE_NVME_BIO_BASED) that leverages
the more direct IO submission path in the block layer; this mode is
used by DM multipath and also optimizes targets like DM thin-pool that
stack directly on NVMe data device.
- DM multipath improvements to factor out legacy SCSI-only
(e.g. scsi_dh) code paths to allow for more optimized support for NVMe
multipath.
- A fix for DM multipath path selectors (service-time and queue-length)
to select paths in a more balanced way; largely academic but doesn't
hurt.
- Numerous DM raid target fixes and improvements.
- Add a new DM "unstriped" target that enables Intel to workaround
firmware limitations in some NVMe drives that are striped internally
(this target also works when stacked above the DM "striped" target).
- Various Documentation fixes and improvements.
- Misc. cleanups and fixes across various DM infrastructure and targets
(e.g. bufio, flakey, log-writes, snapshot).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJacgwPAAoJEMUj8QotnQNaEw0H/0XRTcg8/lRuGl46kdeI3PgR
ZxUy4XgUrCLiACWO5yCU/nKipB32+3xTlTDTBcjmaBfX8HolH147Pasb1KdHqLVC
dOWLMpjlFztb5fnuOMitJA05qQAbgRlZ52QdVk/FDo9yWicgWjQZduh8aYX53pHw
6XOYWzSFAXQcaduPdz6TLiPw479xBwIpXxQbrO09f4qt3Ub4bqknEhzFXc+6M7zl
ejmW/bG2Qg6WmsfAuaAhFTV0LpTPSEzvaq9TfR7yqFU3DvDIAi7Yh8eQinIUDo4u
txpOGoESRAMPAMKH0/UJdr/u7jTsfgJox4QEavWfnViPvkouah5KdjVOL1veZ5U=
=R3dN
-----END PGP SIGNATURE-----
Merge tag 'for-4.16/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- DM core fixes to ensure that bio submission follows a depth-first
tree walk; this is critical to allow forward progress without the
need to use the bioset's BIOSET_NEED_RESCUER.
- Remove DM core's BIOSET_NEED_RESCUER based dm_offload infrastructure.
- DM core cleanups and improvements to make bio-based DM more efficient
(e.g. reduced memory footprint as well leveraging per-bio-data more).
- Introduce new bio-based mode (DM_TYPE_NVME_BIO_BASED) that leverages
the more direct IO submission path in the block layer; this mode is
used by DM multipath and also optimizes targets like DM thin-pool
that stack directly on NVMe data device.
- DM multipath improvements to factor out legacy SCSI-only (e.g.
scsi_dh) code paths to allow for more optimized support for NVMe
multipath.
- A fix for DM multipath path selectors (service-time and queue-length)
to select paths in a more balanced way; largely academic but doesn't
hurt.
- Numerous DM raid target fixes and improvements.
- Add a new DM "unstriped" target that enables Intel to workaround
firmware limitations in some NVMe drives that are striped internally
(this target also works when stacked above the DM "striped" target).
- Various Documentation fixes and improvements.
- Misc cleanups and fixes across various DM infrastructure and targets
(e.g. bufio, flakey, log-writes, snapshot).
* tag 'for-4.16/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (69 commits)
dm cache: Documentation: update default migration_throttling value
dm mpath selector: more evenly distribute ties
dm unstripe: fix target length versus number of stripes size check
dm thin: fix trailing semicolon in __remap_and_issue_shared_cell
dm table: fix NVMe bio-based dm_table_determine_type() validation
dm: various cleanups to md->queue initialization code
dm mpath: delay the retry of a request if the target responded as busy
dm mpath: return DM_MAPIO_DELAY_REQUEUE if QUEUE_IO or PG_INIT_REQUIRED
dm mpath: return DM_MAPIO_REQUEUE on blk-mq rq allocation failure
dm log writes: fix max length used for kstrndup
dm: backfill missing calls to mutex_destroy()
dm snapshot: use mutex instead of rw_semaphore
dm flakey: check for null arg_name in parse_features()
dm thin: extend thinpool status format string with omitted fields
dm thin: fixes in thin-provisioning.txt
dm thin: document representation of <highest mapped sector> when there is none
dm thin: fix documentation relative to low water mark threshold
dm cache: be consistent in specifying sectors and SI units in cache.txt
dm cache: delete obsoleted paragraph in cache.txt
dm cache: fix grammar in cache-policies.txt
...
Fixes the following sparse warning:
drivers/md/dm-raid.c:33:1: warning:
symbol 'raid_sets' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
No need to calculate the reshaping progress because
mddev->curr_resync_completed holds it.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During reshape, 'A' chars were reported in status rather than 'a'.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In order to avoid redoing synchronization/recovery/reshape partially,
the raid set got frozen until after all passed in table line flags had
been cleared. The related table reload sequence had to be precisely
followed, or reshaping may lead to data corruption caused by the active
mapping carrying on with a reshape when the inactive mapping already
had retrieved a stale reshape position.
Harden by retrieving the actual resync/recovery/reshape position
during resume whilst the active table is suspended thus avoiding
to keep the raid set frozen altogether. This prevents superfluous
redoing of an already resynchronized or recovered segment and,
most importantly, potential for redoing of an already reshaped
segment causing data corruption.
Fixes: d39f0010e ("dm raid: fix raid_resume() to keep raid set frozen as needed")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Verifying the current raid sets redundancy based on retrieved
superblock content has to use the superblock's raid level (e.g. raid0),
not the constructor requested one (e.g. raid10).
Using the requested raid level of raid10 lead to a "divide error"
on raid0 which defines data copies divided by to be zero.
Also check for bogus data copies.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In do_md_run(), md threads should not wake up until the array is fully
initialized in md_run(). However, in raid5_run(), raid5-cache may wake
up mddev->thread to flush stripes that need to be written back. This
design doesn't break badly right now. But it could lead to bad bug in
the future.
This patch tries to resolve this problem by splitting start up work
into two personality functions, run() and start(). Tasks that do not
require the md threads should go into run(), while task that require
the md threads go into start().
r5l_load_log() is moved to raid5_start(), so it is not called until
the md threads are started in do_md_run().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Move raid_resume()'s setting of 'rw' and 'in_sync' to just prior to
mddev_resume().
Also, remove unused 'bitmap_loaded' member from "struct raid_set".
No functional changes.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix various sync state issues causing racy/bogus sync ratio,
sync_action ad health chars in dm_status() info output.
Sync ratio could be N/N (i.e. 100%) shortly after raid set
creation, i.e. creating a new RaidLV or upconverting a linear LV to
raid1 thus:
"0 2097152 raid raid1 2 Aa 2097162/2097152 recover 0 0 -"
instead of:
"0 2097152 raid raid1 2 Aa 0/2097152 idle 0 0 -"
Sync action could be non-idle, when the MD thread was done with io.
Health chars could be 'A' when they should be 'a' for a short time
before a resynchonization started.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The raid_status() function passes the bool array_in_sync variable around
providing synchronization state of the MD array. Replace it with a
runtime flag. This will avoid a pattern of having to pass discrete
variables to various functions.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The MD sync thread updates recovery flags providing state of any
running, idle, frozen, recovering, reshaping, ... activity it performs
and updates respective flags asynchronously versus dm processing
raid_status(). To close that race window, take a single copy of the
flags and pass it into its callees.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During a reshape request: if userspace reloads a "raid" table multiple
times, resulting in multiple superblock reads, the raid set needs to
stay frozen until all config changes (chunk size, layout data_offset,
delta_disks) have been stored in the superblocks and respective flags
cleared.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Check all component data device sizes versus calculated size.
Reject if device(s) are too small. Otherwise, MD will fail the
operation by accessing beyond the end of the data device.
An example use-case is that growing bitmap won't fit any more and the MD
runtime will report an error when DM raid should catch this earlier.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The raid set size is being revalidated unconditionally before a
reshaping conversion is started. MD requires the size to only be
reduced in case of a stripe removing (i.e. shrinking) reshape but not
when growing because the raid array has to stay small until after the
growing reshape finishes.
Fix by avoiding the size revalidation in preresume unless a shrinking
reshape is requested.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pay attention to existing reshape space to define if a raid set needs
resizing. Otherwise we can hit "Can't resize a reshaping raid set"
when a reshape is being requested.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The md raid personalities call md_finish_reshape() at the end of a
reshape conversion which adjusts rdev->sectors.
Correct/check rdev->sectors before initiating a reshape and raise the
recovery pointer accordingly.
Otherwise, the DM raid coordinated reshape will fail.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
md_stop_writes() is called in raid_presuspend() causing deadlocks on
bios submitted afterwards -- which happens on loaded raid sets with
conversion requests.
Fix by moving md_stop_writes() to raid_postsuspend(). NOTE: when the
recovery's frozen (MD_RECOVERY_FROZEN), writes haven't been started (or
are already stopped) so don't stop them again.
Also remove superfluous readonly setting.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
isn't _really_ an error
- A DM core @stable fix for discard support that was enabled for an
entire DM device despite only having partial support for discards due
to a mix of discard capabilities across the underlying devices.
- A couple other DM core discard fixes.
- A DM bufio @stable fix that resolves a 32-bit overflow
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaDglsAAoJEMUj8QotnQNaaFwIAMLjV27BYtHBYWnvMlROiXAD
2aPSEoGHEGcq6BQyTlXyew1CNl0xXOcb8KMFhQMR/IjPuKyLl47OXbavE3TIwVoT
Lw+XUvXUuxK1Qd34fUvPoPd94w1aJBoY9Wlv5YxCp+U0WQ2SH3kHo/FOFvLPJ6wY
OhHZiByGvxXWc8tso86zx0pq6j5Nghk18D2lQvaGU28BtElfWE3/xoDr6FrwDqEb
MvzmUMKs/M5EoJt3HT4SNDFqujkCP69PGjqpHxV9mFT8HaonX+MF61Kr96/Tc6cO
c+DOkw7kaqnjJsrdKu3KIdtXf3cyoHYqtExXRdzap8QoCQvosNR4r78svcfY0i8=
=QKXY
-----END PGP SIGNATURE-----
Merge tag 'for-4.15/dm-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull more device mapper updates from Mike Snitzer:
"Given your expected travel I figured I'd get these fixes to you sooner
rather than later.
- a DM multipath stable@ fix to silence an annoying error message
that isn't _really_ an error
- a DM core @stable fix for discard support that was enabled for an
entire DM device despite only having partial support for discards
due to a mix of discard capabilities across the underlying devices.
- a couple other DM core discard fixes.
- a DM bufio @stable fix that resolves a 32-bit overflow"
* tag 'for-4.15/dm-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm bufio: fix integer overflow when limiting maximum cache size
dm: clear all discard attributes in queue_limits when discards are disabled
dm: do not set 'discards_supported' in targets that do not need it
dm: discard support requires all targets in a table support discards
dm mpath: remove annoying message of 'blk_get_request() returned -11'
The DM target's 'discards_supported' flag is intended to act as an
override. Meaning, even if the underlying storage doesn't support
discards the DM target will.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull MD update from Shaohua Li:
"This update mostly includes bug fixes:
- md-cluster now supports raid10 from Guoqing
- raid5 PPL fixes from Artur
- badblock regression fix from Bo
- suspend hang related fixes from Neil
- raid5 reshape fixes from Neil
- raid1 freeze deadlock fix from Nate
- memleak fixes from Zdenek
- bitmap related fixes from Me and Tao
- other fixes and cleanups"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (33 commits)
md: free unused memory after bitmap resize
md: release allocated bitset sync_set
md/bitmap: clear BITMAP_WRITE_ERROR bit before writing it to sb
md: be cautious about using ->curr_resync_completed for ->recovery_offset
badblocks: fix wrong return value in badblocks_set if badblocks are disabled
md: don't check MD_SB_CHANGE_CLEAN in md_allow_write
md-cluster: update document for raid10
md: remove redundant variable q
raid1: remove obsolete code in raid1_write_request
md-cluster: Use a small window for raid10 resync
md-cluster: Suspend writes in RAID10 if within range
md-cluster/raid10: set "do_balance = 0" if area is resyncing
md: use lockdep_assert_held
raid1: prevent freeze_array/wait_all_barriers deadlock
md: use TASK_IDLE instead of blocking signals
md: remove special meaning of ->quiesce(.., 2)
md: allow metadata update while suspending.
md: use mddev_suspend/resume instead of ->quiesce()
md: move suspend_hi/lo handling into core md code
md: don't call bitmap_create() while array is quiesced.
...
Requesting a sync on an active raid device via a table reload
(see 'sync' parameter in Documentation/device-mapper/dm-raid.txt)
skips the super_load() call that defines the superblock size
(rdev->sb_size) -- resulting in an oops if/when super_sync()->memset()
is called.
Fix by moving the initialization of the superblock start and size
out of super_load() to the caller (analyse_superblocks).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Heinz Mauelshagen