Talyn-MB introduces various of FW download options:
FW download via PCIe, SPI or PBL for secured access.
The boot and FW download path is determined based on the
OTP HW register. Driver reads this register as part of the
SW reset flow and performs the appropriate initialization
sequence.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enhanced DMA RX data path is handled using a single
RX descriptor ring for all VIFs.
Multiple RX status rings are supported, to allow RSS
and multi MSI support.
The driver gets the RX completions via the RX status rings.
The RX status message includes the completed RX buffer ID,
which points to the allocated SKB.
The enhanced DMA RX data flow supports RX chaining, where
multiple SKBs are merged into a single packet.
Enhanced DMA HW supports RX HW reorder offload, enabled by
default for Talyn-MB.
amsdu_en debugfs entry was added to allow control MSDU aggregation.
Use the following command to disable AMSDU (enabled by default):
echo 0 > amsdu_en
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enhanced DMA TX data path is handled using a descriptor
ring per connection and a single status ring.
The driver gets TX completions via the TX status ring. Each
status message points to the completed descriptor ring and
includes the number of completed descriptors in this ring.
Non TSO enhanced DMA TX descriptors are similar to legacy DMA
TX descriptors, hence the same transmit function can be used.
However, enhanced DMA TSO frames division is performed by the
HW, hence a new function is added to handle enhanced DMA TSO.
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enhanced DMA design includes the following rings:
- Single RX descriptor ring is used for all VIFs
- Multiple RX status rings are supported, to allow RSS
- TX descriptor ring is allocated per connection
- A single TX status ring is used for all TX descriptor rings
This patch initializes and frees the above descriptor and
status rings.
The RX SKBs are handled by a new entity of RX buffers manager,
which handles RX buffers, each one points to an allocated SKB.
During Rx completion processing, the driver extracts a buffer
ID which is used as an index to the buffers array.
After the SKB is freed the buffer is moved from the 'active'
list to the 'free' list, indicating it can be used for another
descriptor. During Rx refill, SKBs are allocated and attached
to 'free' buffers. Those buffers are attached to new descriptors
and moved to the 'active' list.
New debugfs entries were added to allow edma configuration:
Run the following command to configure the number of status rings:
echo NUM_OF_STATUS_RINGS > num_rx_status_rings
Run the following command to use extended RX status message for
additional debug fields from HW:
echo 0 > compressed_rx_status
Run the following command to control the size of the TX status ring:
echo TX_STATUS_RING_ORDER > tx_status_ring_order
The status ring size will be 1 << tx_status_ring_order
Run the following command to control the size of the RX status ring:
echo RX_STATUS_RING_ORDER > rx_status_ring_order
Due to HW constrains RX sring order should be bigger than RX ring order
The status ring size will be 1 << rx_status_ring_order
Run the following command to change the number of RX buffer IDs:
echo RX_BUFF_ID_COUNT > rx_buff_id_count
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In enhanced DMA the vrings are handled internally by the FW
and are not exposed to the driver.
Instead, the driver handles descriptor rings, which are mapped
by the FW to vrings.
The completions of the TX and RX descriptors are notified to
the driver using status rings. Each status ring descriptor
includes information of the completed descriptors and the ring id
of their descriptor ring.
This patch changes struct vring to generic wil_ring to allow
its reuse for enhanced DMA descriptor rings and adds the descriptor
and status rings specific descriptors.
The vring debugfs entries have changed as follows:
- dbg_vring_index has changed to dbg_ring_index
- vrings has changed to rings
- vring_idle_trsh has changed to ring_idle_trsh
- vring_index has changed to ring_index
Signed-off-by: Gidon Studinski <gidons@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add changes to support initialization of Talyn-MB wil6210
device:
- Add definition for Talyn-MB new JTAG id
- Define talyn_mb_fw_mapping array
- Add Talyn-MB reset sequence
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unused members from struct wil_tid_ampdu_rx
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having new function wmi_mgmt_tx() to take care
of the WMI part of wil_cfg80211_mgmt_tx().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change the type of the argument reply_size from u8 to
u16 in order to support reply sizes > 255 bytes.
The driver already supports u16 reply size in all
other places, this was the only missing change.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Track the connection status per-VIF.
The data path code is also updated to support multiple VIFs.
This includes RX and TX VRING management, NAPI poll loops,
RX reordering and related code.
Power management code used to check if the main interface
is up or based on connection state of the main interface,
adapt this code to take all VIFs into account.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As more support is added for multiple VIFs, there is a need
to protect the wil6210_vif structure from access while it is
deleted (mainly from del_virtual_intf operation).
Instead of adding another mutex, use p2p_wdev_mutex and rename
it to vif_mutex to reflect the added role. Its existing roles
are similar so it extends nicely (for example it protects the
scan_request member which is also a member of wil6210_vif).
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for multiple VIFs in the cfg80211 operations start_ap,
stop_ap and change_beacon. This change allows starting multiple APs
using virtual interfaces.
The data path and most other operations are still working only
on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add generic support in cfg80211 operations add_virtual_intf
and del_virtual_intf for adding/removing VIFs of any
interface type, and fix change_virtual_intf to allow changing
the interface type of a VIF. Previously these operations
only worked for the P2P_DEVICE interface which is not a real
VIF(it is management-only and shares radio with the main
interface).
Currently the interface combination is validated, the VIF is
added/removed in the firmware and the appropriate net/wireless
device is also added/removed.
Added minimal support for proper interface up/down and module
unload but most operations still work only on the main interface.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simple infrastructure changes for supporting multiple
virtual interfaces (multiple VIFs).
It is still not possible to add new VIFs so the only VIF
belongs to the main interface.
Main changes:
1. Add MAC ID(mid) argument to wmi_send and wmi_call to
allow invoking WMI commands on different VIFs.
2. Similarly, in WMI event handler look at the mid reported
by FW and extract VIF structure (currently only for main
interface). All WMI event handlers operate on wil6210_vif
structure so they know on which VIF they were called.
3. Trivial changes to use wil6210_vif structure and MID
throughout the code.
4. Various changes to logging to report MID.
More complete multiple VIFs support will be added gradually
in next patches.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW which supports multiple virtual interfaces, reports
its allowed interface combinations using a special comment
record in the FW file. The format of the interface combinations
is similar to the kernel wiphy->iface_combinations.
When parsing FW file during module initialization, also parse
and validate the concurrency record, and initialize
wiphy->n_iface_combinations and wiphy->iface_combinations
accordingly.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For supporting multiple virtual interfaces in the future,
introduce a wil6210_vif structure which will hold per-VIF
data. Change the module initialization so wil6210_vif will
be part of net_device structure, and wireless_dev will be
embedded inside the wil6210_vif structure. This will allow
us to find the appropriate wil6210_vif structure when we
only have access to wireless_dev or net_device.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to allow using the same brd file across different
11ad chips, the address for loading the brd file should be
part of the FW file, instead of the brd file. The brd file is
expected to include only one section.
To allow backward compatibility the driver reads the
address from the brd file in case it is not included in the
FW file.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sparrow D0 chips have slightly larger mac_rgf_ext section
in order to support extra features such as multiple virtual
interfaces.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when we want to bring the interface up, we first
reset the device which causes the boot loader to run. Then
we halt the device CPU, load FW image and resume the device
CPU.
There are some boot loader versions which perform redundant
memory accesses even when idle. Halting the device CPU
while boot loader access memory can cause the device memory
controller to get stuck, the FW will fail to load and the
network interface will not come up.
For such boot loaders implement a workaround where we freeze
the boot loader before halting the device CPU, so it will not
perform any memory accesses.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
OTP HW vectors values are different for 40MHz and 330MHz AHB
clocks.
In SW reset flow, the host driver sets the clock frequency
to 40MHz. In order to allow reading from the OTP, the host
driver should configure the OTP HW vectors with the values
that fits this clock frequency.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn device supports boot without flash.
Driver detects flashless device and in this case waits for ready indication
from HW machine (instead of bootloader ready indication). Also in this
case, MAC address is retrieved from OTP.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Talyn memory has changed, areas were increased and shifted
to new locations.
Use the appropriate address map according to the device JTAG ID.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add Talyn JTAG ID to the list of valid IDs
and identify this device as Talyn.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The field preset_chandef of wireless_dev must not be accessed
by the driver because it is private to cfg80211. Store the
monitor channel locally in wil6210_priv instead.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"FIXME: IRQ mask debug" and "FIXME: interrupts enabled - for debug"
can be removed because wil6210_debug_irq_mask() is now considered
production feature.
"FIXME FW can transmit only ucast frames to peer" and "FIXME real
ring_id instead of hard coded 0" can be removed because FW/HW already
support multicast transmission.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Suspend and crash dump operations can happen simultaneously
in case there is a FW assert during the suspend procedure
or when SSR calls all the devices crashdump callbacks.
To prevent that, a new flag is added, indicating that the
dumps collection is in progress, in order to allow the
suspend/reset decline if the dumps collection already started.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add get_capa callback to platform ops to allow reading the platform
capabilities.
Supported capabilities:
- Keeping 11ad connection during suspend
- T_POWER_ON 0 support
- Usage of external clock
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the option to support 40bit addresses since some platforms
may not support 48bits but support 40bits
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for sched_scan_start/stop by sending PNO commands to FW.
Driver reports max_sched_scan_reqs and invokes
cfg80211_sched_scan_results upon receiving WMI_SCHED_SCAN_RESULT_EVENTID
from FW.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The #ifdef checks are hard to get right, in this case some functions
should have been left inside a CONFIG_PM_SLEEP check as seen by this
message:
drivers/net/wireless/ath/wil6210/pcie_bus.c:489:12: error: 'wil6210_pm_resume' defined but not used [-Werror=unused-function]
drivers/net/wireless/ath/wil6210/pcie_bus.c:484:12: error: 'wil6210_pm_suspend' defined but not used [-Werror=unused-function]
Using an __maybe_unused is easier here, so I'm replacing all the
other #ifdef in this file as well for consistency.
Fixes: 94162666cd ("wil6210: run-time PM when interface down")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently the statistics show how many successful/failed
suspend/resume operations the system had.
Update the statistics by splitting each successful/failed
suspend/resume operations to radio on/off.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently suspend time statistics are showed through debugfs.
Remove time statistics in suspend state since the timing may
not be accurate in that state.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of interface down, radio is turned off but PCIe mastering is
not cleared.
This can cause unexpected PCIe access to the shutdown device.
Fix this by clearing PCIe mastering also in case interface is down
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW capabilities are currently retrieved only during module
initialization, but userspace can replace the firmware while
interface is down, so refresh the FW capabilities when
interface is up (after FW is loaded) to ensure driver
functionality matches the loaded FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow run-time suspend when interface is down, keep card alive when
interface is up.
If driver is in wmi only or debug_fw mode run-time PM won't suspend.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW starts running it can get D0 to D3 interrupt that is a leftover
from previous system suspend while FW was not running.
As this interrupt is not relevant anymore, clear it part of device reset
procedure.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since debugfs is a kernel configuration option, enable the driver to
compile without debugfs.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vring_idle_trsh is used in the operational driver, hence
should not be defined as a debugfs variable.
Signed-off-by: Gidon Studinski <qca_gidons@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store initial FW RF calibration result in driver. Set this calibration
result back to FW after each FW reset in order to avoid future calibration
procedures.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add statistics for total, min and max suspend time, that
calculates the time the 11ad device was in suspend.
Those statistics will help to estimate the power impact
of d3hot feature.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wireless drivers should not be using ioctl interface,
hence remove this interface for wil6210 driver.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to preserve the connection in suspend/resume flow,
wil6210 host allows going to PCIe D3hot state in suspend,
instead of performing a full wil6210 device reset. This
requires the platform ability to initiate wakeup in case of
RX data. To check that, a new platform API is added.
In addition, add cfg80211 suspend/resume callbacks
implementation.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil6210 devices can have different PCIe bar size, hence get the
bar size from PCIe device instead of using a constant bar size.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Module parameter allows to load specific FW used
for FTM testing.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case wil6210 resume fails, wil6210 suspend function will try
to access the suspended device in the next kernel suspend.
To prevent that, add wil_status_suspended flag to indicate if the
device is already suspended and clear it only if the resume succeeds.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
debugfs ioblob function is called by the FW logs scripts
to copy the FW logs via PCIe.
As the FW logs collection is done in parallel to the operational
11AD actions, the HALP voting can take place during 11AD reset flow
and other sensitive scenarios.
To prevent that, remove HALP voting from the ioblob function.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 11ad spec requires 11ad devices to be able to receive 8KB
packets over the air. Currently this is only possible by
loading the driver with mtu_max=7912 but this also forces
a smaller block ACK window size which reduces performance
for stations which transmit normal sized packets (<2KB).
Fix this problem as follows:
1. Add a module parameter rx_large_buf that when set,
will allocate 8KB RX buffers regardless of mtu_max
setting.
2. When receiving block ACK request agree to any window
size not above our maximum, regardless of the mtu_max setting.
This means if the other side transmits small packets (2KB)
it can still set up block ACK with a large window size,
and get better performance.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The power save profile is set to default state in case of FW reset,
regardless of the state before the reset took place.
Fix this by saving the current power save profile and restore it
in case of FW reset.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Maya Erez