xgpio_save_regs() is used in this driver to setup the initial
values of the registers in the hardware.
The relevant registers at that time are:
0x0 -> channel 0 data (32 bits, one for each GPIO on this channel).
0x4 -> channel 0 tri, controls in/out status for each GPIO of this channel.
0x8 -> channel 1 data
0xC -> channel 1 tri
gpio-xilinx.c defines these:
XGPIO_DATA_OFFSET (0x0)
XGPIO_TRI_OFFSET (0x4)
XGPIO_CHANNEL_OFFSET 0x8
Before this patch, the "data" register value of channel 1 was written
at 0x4 intead of 0x8 (overwriting the channel 0 "tri" register),
and the "tri" register value for channel 1 was written at 0x8 instead of 0xC.
Signed-off-by: Raphaël Teysseyre <rteysseyre@gmail.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Assign GPIO chip owner field to chip->dev->driver->owner if it was not
configured by GPIO driver.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now nothing prevents GPIO driver from being unloaded if its gpios
were requested as GPIO IRQs only (without calling gpio_request()).
Hence, add calls of try_module_get()/module_put() into
gpiochip_irq_reqres/relres() to track such scenario properly.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The spinlock 'slock' is used now to protect pcf857x_irq() from itself
which is unnecessary (especially after switching to use threaded
IRQs). Hence, remove it and use mutex to protect device data in IRQ
handler.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio registercannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 59032702ea ("ARM: shmobile: Remove legacy platform
devices from EMEV2 SoC code"), EMMA Mobile SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Niklas Söderlund <niso@kth.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a failure occurs during probe, brcmstb_gpio_remove() is called. In
remove, we call platform_get_drvdata(), but at the time of failure in
the probe the driver data hadn't yet been set which leads to a NULL
ptr dereference in the remove's list_for_each. Call
platform_set_drvdata() and set up list head right after allocating the
priv struct to both avoid the null pointer dereference that could
occur today. To guard against potential future changes, check for
null pointer in remove.
Reported-by: Tim Ross <tross@broadcom.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The variable "desc" is only used for storing the return value at the
end of the function. It is unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver gpio-mvebu.c does not depend on gpio-generic.c at all.
Drop unneeded "select GPIO_GENERIC".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver calls of_mm_gpiochip_add() to add a memory mapped gpio
chip. So, of_mm_gpiochip_remove() should be used when removing it.
The direct call of gpiochip_remove() misses unmapping the register
and freeing the label.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver gpio-altera.c does not depend on gpio-generic.c at all.
Drop unneeded "select GPIO_GENERIC".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver is tristate, so it should be cleanable.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_add_pingroup_range() has a pctldev argument, not pinctrl.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow to determine the current direction configuration by
reading back from the direction register.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
It's pretty silly to do
void *cd = irq_get_chip_data(irq_data->irq);
because that results in cd = irq_data->chip_data, but goes through a
redundant lookup of the irq_data. Use irq_data directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
It's pretty silly to do
irq_data *d = irq_get_irq_data(irq_data->irq);
because that results in d = irq_data, but goes through a lookup of the
irq_data. Use irq_data directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Preparatory patch for the removal of the 'irq' argument from irq flow
handlers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Use irq_set_handler_locked() as it avoids a redundant lookup of the
irq descriptor.
Search and replacement was done with coccinelle:
@@
struct irq_data *d;
expression E1;
@@
-__irq_set_handler_locked(d->irq, E1);
+irq_set_handler_locked(d, E1);
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Hand in irq_data and avoid the redundant lookup of irq_desc.
Originally-from: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Now that all[1] users of the gpiod_get functions are converted to make
use of the up to now optional flags parameter, make it mandatory which
allows to remove some cpp magic.
[1] all but etraxfs-uart which is broken anyhow and I'm allowed to
ignore it by Jesper Nilsson :-)
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
- Fix a recently added memory leak in an error path in the ACPI
resources management code (Dan Carpenter).
- Fix a build warning triggered by an ACPI video header function
that should be static inline (Borislav Petkov).
- Change names of helper function converting struct fwnode_handle
pointers to either struct device_node or struct acpi_device
pointers so they don't conflict with local variable names
(Alexander Sverdlin).
- Make the hibernate core re-enable nonboot CPUs on failures to
disable them as expected (Vitaly Kuznetsov).
- Increase the default timeout of the device suspend watchdog to
prevent it from triggering too early on some systems (Takashi Iwai).
- Prevent the cpuidle powernv driver from registering idle
states with CPUIDLE_FLAG_TIMER_STOP set if CONFIG_TICK_ONESHOT
is unset which leads to boot hangs (Preeti U Murthy).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=vkde
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes that didn't make it to the previous PM+ACPI pull
request or are fixing issues introduced by it.
Specifics:
- Fix a recently added memory leak in an error path in the ACPI
resources management code (Dan Carpenter)
- Fix a build warning triggered by an ACPI video header function that
should be static inline (Borislav Petkov)
- Change names of helper function converting struct fwnode_handle
pointers to either struct device_node or struct acpi_device
pointers so they don't conflict with local variable names
(Alexander Sverdlin)
- Make the hibernate core re-enable nonboot CPUs on failures to
disable them as expected (Vitaly Kuznetsov)
- Increase the default timeout of the device suspend watchdog to
prevent it from triggering too early on some systems (Takashi Iwai)
- Prevent the cpuidle powernv driver from registering idle states
with CPUIDLE_FLAG_TIMER_STOP set if CONFIG_TICK_ONESHOT is unset
which leads to boot hangs (Preeti U Murthy)"
* tag 'pm+acpi-4.2-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
ACPI / video: Inline acpi_video_set_dmi_backlight_type
ACPI / resources: free memory on error in add_region_before()
* acpi-video:
ACPI / video: Inline acpi_video_set_dmi_backlight_type
* device-properties:
ACPI / OF: Rename of_node() and acpi_node() to to_of_node() and to_acpi_node()
* pm-sleep:
PM / sleep: Increase default DPM watchdog timeout to 60
PM / hibernate: re-enable nonboot cpus on disable_nonboot_cpus() failure
* pm-cpuidle:
tick/idle/powerpc: Do not register idle states with CPUIDLE_FLAG_TIMER_STOP set in periodic mode
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
- Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single
pin simultaneously.
- New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
- New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
- Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
- Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UyKm
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Here is the bulk of pin control changes for the v4.2 series: Quite a
lot of new SoC subdrivers and two new main drivers this time, apart
from that business as usual.
Details:
Core functionality:
- Enable exclusive pin ownership: it is possible to flag a pin
controller so that GPIO and other functions cannot use a single pin
simultaneously.
New drivers:
- NXP LPC18xx System Control Unit pin controller
- Imagination Pistachio SoC pin controller
New subdrivers:
- Freescale i.MX7d SoC
- Intel Sunrisepoint-H PCH
- Renesas PFC R8A7793
- Renesas PFC R8A7794
- Mediatek MT6397, MT8127
- SiRF Atlas 7
- Allwinner A33
- Qualcomm MSM8660
- Marvell Armada 395
- Rockchip RK3368
Cleanups:
- A big cleanup of the Marvell MVEBU driver rectifying it to
correspond to reality
- Drop platform device probing from the SH PFC driver, we are now a
DT only shop for SuperH
- Drop obsolte multi-platform check for SH PFC
- Various janitorial: constification, grammar etc
Improvements:
- The AT91 GPIO portions now supports the set_multiple() feature
- Split out SPI pins on the Xilinx Zynq
- Support DTs without specific function nodes in the i.MX driver"
* tag 'pinctrl-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: rockchip: add support for the rk3368
pinctrl: rockchip: generalize perpin driver-strength setting
pinctrl: sh-pfc: r8a7794: add SDHI pin groups
pinctrl: sh-pfc: r8a7794: add MMCIF pin groups
pinctrl: sh-pfc: add R8A7794 PFC support
pinctrl: make pinctrl_register() return proper error code
pinctrl: mvebu: armada-39x: add support for Armada 395 variant
pinctrl: mvebu: armada-39x: add missing SATA functions
pinctrl: mvebu: armada-39x: add missing PCIe functions
pinctrl: mvebu: armada-38x: add ptp functions
pinctrl: mvebu: armada-38x: add ua1 functions
pinctrl: mvebu: armada-38x: add nand functions
pinctrl: mvebu: armada-38x: add sata functions
pinctrl: mvebu: armada-xp: add dram functions
pinctrl: mvebu: armada-xp: add nand rb function
pinctrl: mvebu: armada-xp: add spi1 function
pinctrl: mvebu: armada-39x: normalize ref clock naming
pinctrl: mvebu: armada-xp: rename spi to spi0
pinctrl: mvebu: armada-370: align spi1 clock pin naming
pinctrl: mvebu: armada-370: align VDD cpu-pd pin naming with datasheet
...
Commit 8a0662d9 introduced of_node and acpi_node symbols in global namespace
but there were already ~63 of_node local variables or function parameters
(no single acpi_node though, but anyway).
After debugging undefined but used of_node local varible (which turned out
to reference static function of_node() instead) it became clear that the names
for the functions are too short and too generic for global scope.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- plug a potential race related to chained interrupt handlers
- core updates which address the needs of the x86 irqdomain conversion
- new irqchip callback to support affinity settings for VCPUs
- the usual pile of updates to interrupt chip drivers
- a few helper functions to allow further cleanups and
simplifications
I have a largish pile of coccinelle scripted/verified cleanups and
simplifications pending on top of that, but I prefer to send that
towards the end of the merge window when the arch/driver changes have
hit your tree to avoid API change wreckage as far as possible"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
genirq: Remove bogus restriction in irq_move_mask_irq()
irqchip: atmel-aic5: Add sama5d2 support
irq: spear-shirq: Fix race in installing chained IRQ handler
irq: irq-keystone: Fix race in installing chained IRQ handler
gpio: gpio-tegra: Fix race in installing chained IRQ handler
gpio: gpio-mxs: Fix race in installing chained IRQ handler
gpio: gpio-mxc: Fix race in installing chained IRQ handler
ARM: gemini: Fix race in installing GPIO chained IRQ handler
GPU: ipu: Fix race in installing IPU chained IRQ handler
ARM: sa1100: convert SA11x0 related code to use new chained handler helper
irq: Add irq_set_chained_handler_and_data()
irqchip: exynos-combiner: Save IRQ enable set on suspend
genirq: Introduce helper function irq_data_get_affinity_mask()
genirq: Introduce helper function irq_data_get_node()
genirq: Introduce struct irq_common_data to host shared irq data
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
irqchip: gic: Simplify gic_configure_irq by using IRQCHIP_SET_TYPE_MASKED
irqchip: renesas: intc-irqpin: Improve binding documentation
genirq: Set IRQCHIP_SKIP_SET_WAKE for no_irq_chip
...
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4z0M-0002Sl-Ti@rmk-PC.arm.linux.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4z0H-0002Sf-P9@rmk-PC.arm.linux.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/E1Z4z0C-0002SX-Lj@rmk-PC.arm.linux.org.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes some issues given by checkpatch. Fixes include
bracket placement, spacing and indenting.
Signed-off-by: Daniel Lockyer <thisisdaniellockyer@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now pcf857x_irq() IRQ's dispatcher will try to run nested
IRQ handlers for each GPIO pin which state has changed.
Such IRQs are, actually, spurious and nested IRQ handlers
have to be called only for IRQs wich were enabled by users.
This is not critical issue - just /proc/interrupts
will display counters for unused IRQS:
399: 4 0 pcf857x 0 Edge
428: 1 0 pcf857x 13 Edge
430: 1 0 pcf857x 15 Edge
Hence, fix it by adding irq_enabled field in struct pcf857x to track
enabled GPIO IRQs and corresponding callbacks in pcf857x_irq_chip.
Similar functionality was presented in pcf857x driver, commit
21fd3cd187 ('gpio: pcf857x: call the gpio user handler iff...')
and then it was removed by commit
a39294bdf4 ('gpio: pcf857x: Switch to use gpiolib irqchip...')
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: a39294bdf4 ('gpio: pcf857x: Switch to use gpiolib irqchip helpers')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a driver requests a GPIO described in its _CRS but the GPIO host
controller (gpiochip) driver providing the GPIO has not been loaded yet
acpi_get_gpiod() returns -ENODEV which causes the calling driver to fail.
If the gpiochip driver is loaded afterwards the driver requesting the GPIO
will not notice this.
Better approach is to return -EPROBE_DEFER in such case. Then when the
gpiochip driver appears the driver requesting the GPIO will be probed
again. This also aligns ACPI GPIO lookup code closer to DT as it does
pretty much the same when no gpiochip driver was found.
Reported-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Reviewed-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_gpiochip_request(free)_interrupts can be used for modules,
so export them. This also fixs a compile error when xgene-sb
configured as kernel module.
Fixes: 733cf014f0 "gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver"
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
When requesting own descriptors through hogs, it is useful to
get some details about what's going on if we encounter problems.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These error messages are helpful to see that we fail to get
hogs. Promote them to real errors so they appear in the boot
crawl.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added support to Zynq Ultrascale+ MPSoC on the existing zynq
gpio driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a GPIO driver for the General I/O block on Axis ETRAX FS SoCs.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the GPIO IP "UPG GIO" used on
Broadcom STB SoCs (BCM7XXX and some others). Uses
basic_mmio_gpio to instantiate a gpio_chip for each bank.
The driver assumes that it handles the base set of GPIOs
on the system and that it can start its numbering sequence
from 0, so any GPIO expanders used with it must dynamically
assign GPIO numbers after this driver has finished
registering its GPIOs.
Does not implement the interrupt-controller portion yet,
will be done in a future commit.
v2:
- change include to use <linux/gpio/driver.h> instead of
<linux/gpio.h>
- get rid of unnecessary imask member in struct bank
- rename GPIO_PER_BANK -> MAX_GPIO_PER_BANK
- always have 32 GPIOs per bank and add 'width' member in
struct bank to hold actual number of GPIOs in use
- mark of_match table as const
List-usage-fixed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code uses devm_request_irq() in .probe, so drop the unneeded
free_irq() call in .remove.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CrystalCove GPIO irqchip doesn't have irq_set_wake callback defined
so we should set IRQCHIP_SKIP_SET_WAKE for it or it would cause an irq
desc's wake_depth unbalanced warning during system resume phase from the
gpio_keys driver, which is the driver for the power button of the ASUS
T100 laptop.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes some redundant code but does not have any functional impact.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If an interrupt controller doesn't support wake-up configuration,
irq_set_irq_wake() returns an error code. Then any subsequent call
trying to deconfigure wake-up will cause an imbalance, and a warning
will be printed:
WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x
Unbalanced IRQ 26 wake disable
To fix this, refrain from any further parent interrupt controller
(de)configuration if irq_set_irq_wake() failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
0x3 only masks two bits, but three bits have to be allowed. This fixes
GPHY0 LED2 (which is the highest bit of phy2) on my board.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Interrupts were missed if an 8-bit integer overflow occurred. This was
observed when bank0,pin7 and bank1,pin7 changed simultaniously.
As the 8-bit totals were only checked against zero, replace them with
booleans. Name the booleans so that their purpose is clear.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The omap_gpio_irq_startup() can be called at time when:
- corresponding GPIO has been requested already and in this case
it has to be configured as input already. If not - return with -EINVAL
and do not try to re-configure it as it could be unsafe.
- corresponding GPIO is free: reconfigure GPIO as input.
In addition, call omap_enable_gpio_module directly as all needed
checks are already present inside it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO Chip implementation shouldn't touch GPIO IRQ specific registers
and vise versa.
Hence, rework omap_gpio_request:
- don't reset GPIO IRQ triggering type to IRQ_TYPE_NONE, because
GPIO irqchip should be responsible for that;
- call directly omap_enable_gpio_module as all needed checks are already
present inside it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO Chip and GPIO IRQ Chip functionality are essentially orthogonal,
so GPIO IRQ Chip implementation shouldn't touch GPIO specific
registers and vise versa.
Hence, rework omap_gpio_irq_shutdown and try to touch only irqs specific
registers:
- don't configure GPIO as input (it, actually, should be already configured
as input).
- don't clear debounce configuration if GPIO is still used as GPIO.
We need to take in to account here commit c9c55d9211
("gpio/omap: fix off-mode bug: clear debounce settings on free/reset").
Also remove omap_reset_gpio() function as it is not used any more.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO bank will be kept powered in case if input parameters
are invalid or error occurred in omap_gpio_irq_type.
Hence, fix it by ensuring that GPIO bank will be unpowered
in case of errors and add additional check of value returned
from omap_set_gpio_triggering().
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes following issue:
- GPIOn is used as IRQ by some dev, for example PCF8575.INT -> gpio6.11
- PCFx driver knows nothing about type of IRQ line (GPIO or not)
so it doesn't request gpio and just do request_irq()
- If gpio6.11 will be exported through the sysfs and then un-xeported
then IRQs from PCFx will not be received any more, because
IRQ configuration for gpio6.11 will be cleaned up unconditionally
in omap_gpio_free.
Fix this by removing all GPIO IRQ specific code from omap_gpio_free()
and also do GPIO clean up (change direction to 'in' and disable debounce)
only if corresponding GPIO is not used as IRQ too.
GPIO IRQ will be properly cleaned up by GPIO irqchip code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If an interrupt controller doesn't support wake-up configuration,
irq_set_irq_wake() returns an error code. Then any subsequent call
trying to deconfigure wake-up will cause an imbalance, and a warning
will be printed:
WARNING: CPU: 1 PID: 1341 at kernel/irq/manage.c:540 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 26 wake disable
To fix this, refrain from any further parent interrupt controller
(de)configuration if irq_set_irq_wake() failed.
Alternative fixes would be:
- calling "gic_set_irqchip_flags(IRQCHIP_SKIP_SET_WAKE)" from the
platform code,
- setting "gic_chip.flags = IRQCHIP_SKIP_SET_WAKE" in the GIC driver
code,
but these were withheld as the GIC hardware doesn't really support
wake-up interrupts.
Fixes: ab82fa7da4 ("gpio: rcar: Prevent module clock disable when wake-up is enabled")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There have been concerns that the function names gpiod_set_array() and
gpiod_get_array() might be confusing to users. One might expect
gpiod_get_array() to return array values, while it is actually the array
counterpart of gpiod_get(). To be consistent with the single descriptor API
we could rename gpiod_set_array() to gpiod_set_array_value(). This makes
some function names a bit lengthy: gpiod_set_raw_array_value_cansleep().
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean up chained handler and handler data if they were set by
gpiochip_set_chained_irqchip().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dln2 driver was initialising a gpiolib private field, which is now
gone.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes an inverted return value of the gpio get_direction
function.
The wrong value causes the direction sysfs entry and GPIO debugfs file
to indicate incorrect GPIO direction settings. In some cases it also
prevents setting GPIO output values.
The problem is also present in all other stable kernel versions since
linux-3.12.
Cc: Stable <stable@vger.kernel.org> # v3.12+
Reported-by: Jochen Henneberg <jh@henneberg-systemdesign.com>
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to free any hogged gpios on errors in gpiochip_add.
Also move all forward declarations to the top of the file.
Fixes: f625d46017 ("gpio: add GPIO hogging mechanism")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move irq trigger flags, which as sysfs-interface specific, to the class
device data.
This avoids accessing the gpio-descriptor flags field using non-atomic
operations without any locking, and allows for a more clear separation
of the sysfs interface from gpiolib core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove FLAG_SYSFS_DIR, which is sysfs-interface specific, and store it
in the class-device data instead.
Note that the flag is only used during export.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename active-low helper using common prefix.
Also remove unnecessary manipulation of value argument.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to deregister the class device (and release the irq) while
holding the sysfs lock in gpio_unexport to prevent racing with
gpio_export.
Note that this requires the recently introduced per-gpio locking to
avoid a deadlock with the kernfs active protection when waiting for the
attribute operations to drain during deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a per-gpio mutex to serialise attribute operations rather than use
one global mutex for all gpios and chips.
Having a single global lock for all gpios in a system adds unnecessary
latency to the sysfs interface, and especially when having gpio
controllers connected over slow buses.
Now that the global gpio-sysfs interrupt table is gone and with per-gpio
data in place, we can easily switch to using a more fine-grained locking
scheme.
Keep the global mutex to serialise the global (class) operations of gpio
export and unexport and chip removal.
Also document the locking assumptions made.
Note that this is also needed to fix a race between gpiod_export and
gpiod_unexport.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop unnecessary locking from gpiod_export_link. If the class device has
not already been unregistered, class_find_device returns the ref-counted
class device so there's no need for locking.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Only call irq helper if actually reconfiguring interrupt state.
This is a preparatory step in introducing separate gpio-irq request and
free functions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Store the value sysfs entry in the gpiod data rather than in a global
table accessed through an index stored in the overloaded gpio-descriptor
flag field.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add gpiod class-device data.
This is a first step in getting rid of the insane gpio-descriptor flag
overloading, backward irq-interface implementation, and course grained
sysfs-interface locking (a single static mutex for every operation on
all exported gpios in a system).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The attribute operations will never be called for an unregistered device
so remove redundant checks for FLAG_EXPORT.
Note that kernfs will also guarantee that any active sysfs operation has
finished before the attribute is removed during deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make sure to release any irq only after the class device has been
deregistered.
This avoids a race between gpiod_unexport and edge_store, where an irq
could be allocated just before the gpio class device is deregistered
without relying on FLAG_EXPORT and the global sysfs lock.
Note that there is no need to hold the sysfs lock when releasing the irq
after the class device is gone as kernfs will prevent further attribute
operations.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use DEVICE_ATTR_RO and DEVICE_ATTR_RW rather than specifying masks and
callbacks directly.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove gpiod_sysfs_set_active_low (and gpio_sysfs_set_active_low) which
allowed code to change the polarity of a gpio line even after it had
been exported through sysfs.
Drivers should not care, and generally does not know, about gpio-line
polarity which is a hardware feature that needs to be described by
firmware.
It is currently possible to define gpio-line polarity in device-tree and
acpi firmware or using platform data. Userspace can also change the
polarity through sysfs.
Note that drivers using the legacy gpio interface could still use
GPIOF_ACTIVE_LOW to change the polarity before exporting the gpio.
There are no in-kernel users of this interface.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Harry Wei <harryxiyou@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-doc@vger.kernel.org
Cc: linux-kernel@zh-kernel.org
Cc: linux-arch@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the gpio-chip export/unexport functions to the more descriptive
names gpiochip_sysfs_register and gpiochip_sysfs_unregister.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clean gpio-chip class device registration and deregistration.
The class device is registered when a gpio-chip is added (or from
gpiolib_sysfs_init post-core init call), and deregistered when the chip
is removed.
Store the class device in struct gpio_chip directly rather than do a
class-device lookup on deregistration. This also removes the need for
the exported flag.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Raphaël Teysseyre