Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new configuration for the sama5d3-macb new compatibility string.
This configuration disables scatter-gather because we experienced lock down
of the macb interface of this particular SoC under very high load.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_reset_hw() is called from macb_close() and indirectly from
macb_open(). macb_reset_hw() zeroes the NCR register, including the MPE
(Management Port Enable) bit.
This will prevent accessing any other PHYs for other Ethernet MACs on
the MDIO bus, which remains registered at macb_reset_hw() time, until
macb_init_hw() is called from macb_open() which sets the MPE bit again.
I.e. currently the MDIO bus has a short disruption at open time and is
disabled at close time until the interface is opened again.
Fix that by only touching the RE and TE bits when enabling and disabling
RX/TX.
v2: Make macb_init_hw() NCR write a single statement.
Fixes: 6c36a70744 ("macb: Use generic PHY layer")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 739de9a156 ("net: macb: Reorganize macb_mii bringup") broke
initializing macb on the EVB-KSZ9477 eval board.
There, of_mdiobus_register was called even for the fixed-link representing
the RGMII-link to the switch with the result that the driver attempts to
enumerate PHYs on a non-existent MDIO bus:
libphy: MACB_mii_bus: probed
mdio_bus f0028000.ethernet-ffffffff: fixed-link has invalid PHY address
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 0
[snip]
mdio_bus f0028000.ethernet-ffffffff: scan phy fixed-link at address 31
The "MDIO" bus registration succeeds regardless, having claimed the reset GPIO,
and calling of_phy_register_fixed_link later on fails because it tries
to claim the same GPIO:
macb f0028000.ethernet: broken fixed-link specification
Fix this by registering the fixed-link before calling mdiobus_register.
Fixes: 739de9a156 ("net: macb: Reorganize macb_mii bringup")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For packets with computed IP/TCP/UDP checksum there is no need to tell
hardware to recompute it. For such kind of packets hardware expects the
packet to be at least 64 bytes and FCS to be computed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move checksum clearing outside of spinlock. The SKB is protected by
networking lock (HARD_TX_LOCK()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_tx_t return type for ndo_start_xmit function of macb driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.
When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)
Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx ring is allocated for all queues in macb_alloc_consistent.
Free the same for all queues instead of just Q0.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor guard Kconfig symbols for Cadence and Packet Engines use a
"NET_" prefix, while all other vendor guards use a "NET_VENDOR_"
prefix. Hence make them consistent with the rest, and add the missing
trailing "S" for Packet Engines while at it.
As these options don't directly affect the kernel build, and default to
"y", this change has no impact on kernels built with existing
(def)configs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver currently crashes on at91rm9200 with the following trace:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
[...]
[<c031da44>] (macb_rx_desc) from [<c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<c031f2bc>] (at91ether_open) from [<c041e8d8>] (__dev_open+0x120/0x13c)
[<c041e8d8>] (__dev_open) from [<c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<c041ec08>] (__dev_change_flags) from [<c041ec4c>] (dev_change_flags+0x18/0x4c)
[<c041ec4c>] (dev_change_flags) from [<c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<c07a5f4c>] (ip_auto_config) from [<c000a4fc>] (do_one_initcall+0x78/0x18c)
[<c000a4fc>] (do_one_initcall) from [<c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<c0783e50>] (kernel_init_freeable) from [<c0574d70>] (kernel_init+0x8/0xe8)
[<c0574d70>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When delta passed to gem_ptp_adjtime is negative, the sign is
maintained in the ns_to_timespec64 conversion. Hence timespec_add
should be used directly. timespec_sub will just subtract the negative
value thus increasing the time difference.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches noted that we have a few source files that for some
inexplicable reason (read: I'm too lazy to even go look at the history)
are marked executable:
drivers/gpu/drm/amd/amdgpu/vce_v4_0.c
drivers/net/ethernet/cadence/macb_ptp.c
A simple git command line to show executable C/asm/header files is this:
git ls-files -s '*.[chsS]' | grep '^100755'
and then you can fix them up with scripting by just feeding that output
into:
| cut -f2 | xargs chmod -x
and commit it.
Which is exactly what this commit does.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call of_get_nvmem_mac_address() to fetch the MAC address from an nvmem
cell, if one is provided in the device tree. This allows the address to
be stored in an I2C EEPROM device for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)
The devicetree snippet would look something like this:
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
The work done to add the phy_node in the first place (dacdbb4dfc1a1:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.
This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the rx_fs_lock is no longer held across allocation, it's safe
to use GFP_KERNEL for allocating new entries.
This reverts commit 81da3bf6e3 ("net: macb: change GFP_KERNEL to
GFP_ATOMIC").
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae8223de3d ("net: macb: Added support for RX filtering")
introduces a lock, rx_fs_lock which is intended to protect the list of
rx_flow items and synchronize access to the hardware rx filtering
registers.
However, the region protected by this lock is overscoped, unnecessarily
including things like slab allocation. Reduce this lock scope to only
include operations which must be performed atomically: list traversal,
addition, and removal, and hitting the macb filtering registers.
This fixes the use of kmalloc w/ GFP_KERNEL in atomic context.
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
Cc: Rafal Ozieblo <rafalo@cadence.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list_for_each_entry() macro already handles the case where the list
is empty (by not executing the loop body). It's not necessary to handle
this case specially, so stop doing so.
Cc: Rafal Ozieblo <rafalo@cadence.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function gem_add_flow_filter called on line 2958 inside lock on line 2949
but uses GFP_KERNEL
Generated by: scripts/coccinelle/locks/call_kern.cocci
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
CC: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_node_put(bp->phy_node) to all associated error
paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_phy_deregister_fixed_link to all associated
error paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable work_done is set to zero and this value is never read, instead
it is set to another value a few statements later. Remove the redundant
assignment. Cleans up clang warning:
drivers/net/ethernet/cadence/macb_main.c:1221:2: warning: Value stored
to 'work_done' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
791 336 0 1127 467 net/ethernet/cadence/macb_pci.o
File size After adding 'const':
text data bss dec hex filename
855 272 0 1127 467 net/ethernet/cadence/macb_pci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the SAMA5D3 device specification it supports Jumbo frames.
But the suggested flag and length of bytes it supports was not updated
in this driver config_structure.
The maximum jumbo frames the device supports :
10240 bytes as per the device spec.
While changing the MTU value greater than 1500, it threw error:
sudo ifconfig eth1 mtu 9000
SIOCSIFMTU: Invalid argument
Add this support to driver so that it works as expected and designed.
Signed-off-by: vishnuvardhan <vardhanraj4143@gmail.com>
[nicolas.ferre@microchip.com: modify slightly commit msg]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When macro MACB_EXT_DESC is defined we end up with two identical
return statements and just one is sufficient. Remove the extra
return.
Detected by CoverityScan, CID#1449361 ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on original Harini's patch and Andrei's patch,
implemented in a separate file to ease the review/maintanance
and integration with other platforms.
This driver supports GEM-GXL:
- Register ptp clock framework
- Initialize PTP related registers
- HW time stamp on the PTP Ethernet packets are received using the
SO_TIMESTAMPING API. Time stamps are obtained from the dma buffer
descriptors
- add macb_ptp to compilation chain
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that macb is compiled as a module, macb.c has been renamed to
macb_main.c to avoid naming confusion in Makefile.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP timestamps in
DMA buffer descriptors. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 83a77e9ec4, the phydev irq is explicitly set to PHY_POLL when
there is no pdata. It doesn't work on DT enabled platforms because the
phydev irq is already set by libphy before.
Fixes: 83a77e9ec4 ("net: macb: Added PCI wrapper for Platform Driver.")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
macb, use stats from struct net_device.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Simek