Avoid expensive indirect calls in the fast path DMA mapping
operations by directly calling the dma_direct_* ops if we are using
the directly mapped DMA operations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
While the dma-direct code is (relatively) clean and simple we actually
have to use the swiotlb ops for the mapping on many architectures due
to devices with addressing limits. Instead of keeping two
implementations around this commit allows the dma-direct
implementation to call the swiotlb bounce buffering functions and
thus share the guts of the mapping implementation. This also
simplified the dma-mapping setup on a few architectures where we
don't have to differenciate which implementation to use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
No need to duplicate the mapping logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Only report report a DMA addressability report once to avoid spewing the
kernel log with repeated message. Also provide a stack trace to make it
easy to find the actual caller that caused the problem.
Last but not least move the actual check into the fast path and only
leave the error reporting in a helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Instead of providing a special dma_mark_clean hook just for ia64, switch
ia64 to use the normal arch_sync_dma_for_cpu hooks instead.
This means that we now also set the PG_arch_1 bit for pages in the
swiotlb buffer, which isn't stricly needed as we will never execute code
out of the swiotlb buffer, but otherwise harmless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
We can use DMA_MAPPING_ERROR instead, which already maps to the same
value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
The dummy DMA ops are currently used by arm64 for any device which has
an invalid ACPI description and is thus barred from using DMA due to not
knowing whether is is cache-coherent or not. Factor these out into
general dma-mapping code so that they can be referenced from other
common code paths. In the process, we can prune all the optional
callbacks which just do the same thing as the default behaviour, and
fill in .map_resource for completeness.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[hch: moved to a separate source file]
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
All architectures except for sparc64 use the dma-direct code in some
form, and even for sparc64 we had the discussion of a direct mapping
mode a while ago. In preparation for directly calling the direct
mapping code don't bother having it optionally but always build the
code in. This is a minor hardship for some powerpc and arm configs
that don't pull it in yet (although they should in a relase ot two),
and sparc64 which currently doesn't need it at all, but it will
reduce the ifdef mess we'd otherwise need significantly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
This isn't exactly a slow path routine, but it is not super critical
either, and moving it out of line will help to keep the include chain
clean for the following DMA indirection bypass work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
There is no need to have all setup and coherent allocation / freeing
routines inline. Move them out of line to keep the implemeation
nicely encapsulated and save some kernel text size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
dma_get_required_mask should really be with the rest of the DMA mapping
implementation instead of in drivers/base as a lone outlier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
We can just call the regular calls after adding offset the the address instead
of reimplementing them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Tony Luck <tony.luck@intel.com>
We already zero the memory after allocating it from the pool that
this function fills, and having the memset here in this form means
we can't support CMA highmem allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Russell King - ARM Linux <linux@armlinux.org.uk>
DMA debug entries are one of those things which aren't that useful
individually - we will always want some larger quantity of them - and
which we don't really need to manage the exact number of - we only care
about having 'enough'. In that regard, the current behaviour of creating
them one-by-one leads to a lot of unwarranted function call overhead and
memory wasted on alignment padding.
Now that we don't have to worry about freeing anything via
dma_debug_resize_entries(), we can optimise the allocation behaviour by
grabbing whole pages at once, which will save considerably on the
aforementioned overheads, and probably offer a little more cache/TLB
locality benefit for traversing the lists under normal operation. This
should also give even less reason for an architecture-level override of
the preallocation size, so make the definition unconditional - if there
is still any desire to change the compile-time value for some platforms
it would be better off as a Kconfig option anyway.
Since freeing a whole page of entries at once becomes enough of a
challenge that it's not really worth complicating dma_debug_init(), we
may as well tweak the preallocation behaviour such that as long as we
manage to allocate *some* pages, we can leave debugging enabled on a
best-effort basis rather than otherwise wasting them.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
With the only caller now gone, we can clean up this part of dma-debug's
exposed internals and make way to tweak the allocation behaviour.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we can dynamically allocate DMA debug entries to cope with
drivers maintaining excessively large numbers of live mappings, a driver
which *does* actually have a bug leaking mappings (and is not unloaded)
will no longer trigger the "DMA-API: debugging out of memory - disabling"
message until it gets to actual kernel OOM conditions, which means it
could go unnoticed for a while. To that end, let's inform the user each
time the pool has grown to a multiple of its initial size, which should
make it apparent that they either have a leak or might want to increase
the preallocation size.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Certain drivers such as large multi-queue network adapters can use pools
of mapped DMA buffers larger than the default dma_debug_entry pool of
65536 entries, with the result that merely probing such a device can
cause DMA debug to disable itself during boot unless explicitly given an
appropriate "dma_debug_entries=..." option.
Developers trying to debug some other driver on such a system may not be
immediately aware of this, and at worst it can hide bugs if they fail to
realise that dma-debug has already disabled itself unexpectedly by the
time their code of interest gets to run. Even once they do realise, it
can be a bit of a pain to emprirically determine a suitable number of
preallocated entries to configure, short of massively over-allocating.
There's really no need for such a static limit, though, since we can
quite easily expand the pool at runtime in those rare cases that the
preallocated entries are insufficient, which is arguably the least
surprising and most useful behaviour. To that end, refactor the
prealloc_memory() logic a little bit to generalise it for runtime
reallocations as well.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use pr_fmt() to generate the "DMA-API: " prefix consistently. This
results in it being added to a couple of pr_*() messages which were
missing it before, and for the err_printk() calls moves it to the actual
start of the message instead of somewhere in the middle.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Expose nr_total_entries in debugfs, so that {num,min}_free_entries
become even more meaningful to users interested in current/maximum
utilisation. This becomes even more relevant once nr_total_entries
may change at runtime beyond just the existing AMD GART debug code.
Suggested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The dma-direct code already returns (~(dma_addr_t)0x0) on mapping
failures, so we can switch over to returning DMA_MAPPING_ERROR and let
the core dma-mapping code handle the rest.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit bfd56cd605 ("dma-mapping: support highmem in the generic remap
allocator") replaced dma_direct_alloc_pages() with __dma_direct_alloc_pages(),
which doesn't set dma_handle and zero allocated memory. Fix it by doing this
directly in the caller function.
Fixes: bfd56cd605 ("dma-mapping: support highmem in the generic remap allocator")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Do not waste vmalloc space on allocations that do not require a mapping
into the kernel address space.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
By using __dma_direct_alloc_pages we can deal entirely with struct page
instead of having to derive a kernel virtual address.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
The arm64 codebase to implement coherent dma allocation for architectures
with non-coherent DMA is a good start for a generic implementation, given
that is uses the generic remap helpers, provides the atomic pool for
allocations that can't sleep and still is realtively simple and well
tested. Move it to kernel/dma and allow architectures to opt into it
using a config symbol. Architectures just need to provide a new
arch_dma_prep_coherent helper to writeback an invalidate the caches
for any memory that gets remapped for uncached access.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
The dma remap code only makes sense for not cache coherent architectures
(or possibly the corner case of highmem CMA allocations) and currently
is only used by arm, arm64, csky and xtensa. Split it out into a
separate file with a separate Kconfig symbol, which gets the right
copyright notice given that this code was written by Laura Abbott
working for Code Aurora at that point.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
dma_alloc_from_contiguous can return highmem pages depending on the
setup, which a plain non-remapping DMA allocator can't handle. Detect
this case and fail the allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Some architectures support remapping highmem into DMA coherent
allocations. To use the common code for them we need variants of
dma_direct_{alloc,free}_pages that do not use kernel virtual addresses.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
If swiotlb_bounce_page() failed, calling arch_sync_dma_for_device() may
lead to such delights as performing cache maintenance on whatever
address phys_to_virt(SWIOTLB_MAP_ERROR) looks like, which is typically
outside the kernel memory map and goes about as well as expected.
Don't do that.
Fixes: a4a4330db4 ("swiotlb: add support for non-coherent DMA")
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move remaining definitions and declarations from include/linux/bootmem.h
into include/linux/memblock.h and remove the redundant header.
The includes were replaced with the semantic patch below and then
semi-automated removal of duplicated '#include <linux/memblock.h>
@@
@@
- #include <linux/bootmem.h>
+ #include <linux/memblock.h>
[sfr@canb.auug.org.au: dma-direct: fix up for the removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181002185342.133d1680@canb.auug.org.au
[sfr@canb.auug.org.au: powerpc: fix up for removal of linux/bootmem.h]
Link: http://lkml.kernel.org/r/20181005161406.73ef8727@canb.auug.org.au
[sfr@canb.auug.org.au: x86/kaslr, ACPI/NUMA: fix for linux/bootmem.h removal]
Link: http://lkml.kernel.org/r/20181008190341.5e396491@canb.auug.org.au
Link: http://lkml.kernel.org/r/1536927045-23536-30-git-send-email-rppt@linux.vnet.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle architectures that are not cache coherent directly in the main
swiotlb code by calling arch_sync_dma_for_{device,cpu} in all the right
places from the various dma_map/unmap/sync methods when the device is
non-coherent.
Because swiotlb now uses dma_direct_alloc for the coherent allocation
that side is already taken care of by the dma-direct code calling into
arch_dma_{alloc,free} for devices that are non-coherent.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
All architectures that support swiotlb also have a zone that backs up
these less than full addressing allocations (usually ZONE_DMA32).
Because of that it is rather pointless to fall back to the global swiotlb
buffer if the normal dma direct allocation failed - the only thing this
will do is to eat up bounce buffers that would be more useful to serve
streaming mappings.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Remove the somewhat useless map_single function, and replace it with a
swiotlb_bounce_page handler that handles everything related to actually
bouncing a page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
No need to duplicate the code - map_sg is equivalent to map_page
for each page in the scatterlist.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Like all other dma mapping drivers just return an error code instead
of an actual memory buffer. The reason for the overflow buffer was
that at the time swiotlb was invented there was no way to check for
dma mapping errors, but this has long been fixed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
All properly written drivers now have error handling in the
dma_map_single / dma_map_page callers. As swiotlb_tbl_map_single already
prints a useful warning when running out of swiotlb pool space we can
also remove swiotlb_full entirely as it serves no purpose now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This comments describes an aspect of the map_sg interface that isn't
even exploited by swiotlb.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Respect the DMA_ATTR_NO_WARN flags for allocations in dma-direct.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
I recently debugged a DMA mapping oops where a driver was trying to map
a buffer returned from request_firmware() with dma_map_single(). Memory
returned from request_firmware() is mapped into the vmalloc region and
this isn't a valid region to map with dma_map_single() per the DMA
documentation's "What memory is DMA'able?" section.
Unfortunately, we don't really check that in the DMA debugging code, so
enabling DMA debugging doesn't help catch this problem. Let's add a new
DMA debug function to check for a vmalloc address or an invalid virtual
address and print a warning if this happens. This makes it a little
easier to debug these sorts of problems, instead of seeing odd behavior
or crashes when drivers attempt to map the vmalloc space for DMA.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It appears that in commit 9d7a224b46 ("dma-direct: always allow dma mask
<= physiscal memory size") the logic of the test was changed from a "<" to
a ">=" however I don't see any reason for that change. I am assuming that
there was some additional change planned, specifically I suspect the logic
was intended to be reversed and possibly used for a return. Since that is
the case I have gone ahead and done that.
This addresses issues I had on my system that prevented me from booting
with the above mentioned commit applied on an x86_64 system w/ Intel IOMMU.
Fixes: 9d7a224b46 ("dma-direct: always allow dma mask <= physiscal memory size")
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This way an architecture with less than 4G of RAM can support dma_mask
smaller than 32-bit without a ZONE_DMA. Apparently that is a common
case on powerpc.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Instead of rejecting devices with a too small bus_dma_mask we can handle
by taking the bus dma_mask into account for allocations and bounce
buffering decisions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
We need to take the DMA offset and encryption bit into account when
selecting a zone. User the opportunity to factor out the zone
selection into a helper for reuse.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
This is somewhat modelled after the powerpc version, and differs from
the legacy fallback in use fls64 instead of pointlessly splitting up the
address into low and high dwords and in that it takes (__)phys_to_dma
into account.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
We can use the arch_dma_coherent_to_pfn hook to provide a ->get_sgtable
implementation. Note that this isn't an endorsement of this interface
(which is a horrible bad idea), but it is required to move arm64 over
to the generic code without a loss of functionality.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The only functional differences (modulo a few missing fixes in the arch
code) is that architectures without coherent caches need a hook to
convert a virtual or dma address into a pfn, given that we don't have
the kernel linear mapping available for the otherwise easy virt_to_page
call. As a side effect we can support mmap of the per-device coherent
area even on architectures not providing the callback, and we make
previous dangerous default methods dma_common_mmap actually save for
non-coherent architectures by rejecting it without the right helper.
In addition to that we need a hook so that some architectures can
override the protection bits when mmaping a dma coherent allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
All the cache maintainance is already stubbed out when not enabled,
but merging the two allows us to nicely handle the case where
cache maintainance is required for some devices, but not others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
Various architectures support both coherent and non-coherent dma on a
per-device basis. Move the dma_noncoherent flag from the mips archdata
field to struct device proper to prepare the infrastructure for reuse on
other architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch adding the infrastructure failed to actually add the symbol
declaration, oops..
Fixes: faef87723a ("dma-noncoherent: add a arch_sync_dma_for_cpu_all hook")
Signed-off-by: Christoph Hellwig <hch@lst.de>
early_cma does not check input argument before passing it to
simple_strtoull. The argument would be a NULL pointer if "cma", without
its value, is set in command line and thus causes the following panic.
PANIC: early exception 0xe3 IP 10:ffffffffa3e9db8d error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-rc3-yocto-standard+ #7
[ 0.000000] RIP: 0010:_parse_integer_fixup_radix+0xd/0x70
...
[ 0.000000] Call Trace:
[ 0.000000] simple_strtoull+0x29/0x70
[ 0.000000] memparse+0x26/0x90
[ 0.000000] early_cma+0x17/0x6a
[ 0.000000] do_early_param+0x57/0x8e
[ 0.000000] parse_args+0x208/0x320
[ 0.000000] ? rdinit_setup+0x30/0x30
[ 0.000000] parse_early_options+0x29/0x2d
[ 0.000000] ? rdinit_setup+0x30/0x30
[ 0.000000] parse_early_param+0x36/0x4d
[ 0.000000] setup_arch+0x336/0x99e
[ 0.000000] start_kernel+0x6f/0x4e6
[ 0.000000] x86_64_start_reservations+0x24/0x26
[ 0.000000] x86_64_start_kernel+0x6f/0x72
[ 0.000000] secondary_startup_64+0xa4/0xb0
This patch adds a check to prevent the panic.
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
This goes through a lot of hooks just to call arch_teardown_dma_ops.
Replace it with a direct call instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
There is no good reason for this indirection given that the method
always exists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
When a device has a DMA offset the dma capable result will change due
to the difference between the physical and DMA address. Take that into
account.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
The CMA memory allocator doesn't support standard gfp flags for memory
allocation, so there is no point having it as a parameter for
dma_alloc_from_contiguous() function. Replace it by a boolean no_warn
argument, which covers all the underlaying cma_alloc() function
supports.
This will help to avoid giving false feeling that this function supports
standard gfp flags and callers can pass __GFP_ZERO to get zeroed buffer,
what has already been an issue: see commit dd65a941f6 ("arm64:
dma-mapping: clear buffers allocated with FORCE_CONTIGUOUS flag").
Link: http://lkml.kernel.org/r/20180709122020eucas1p21a71b092975cb4a3b9954ffc63f699d1~-sqUFoa-h2939329393eucas1p2Y@eucas1p2.samsung.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Laura Abbott <labbott@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cma_alloc() doesn't really support gfp flags other than __GFP_NOWARN, so
convert gfp_mask parameter to boolean no_warn parameter.
This will help to avoid giving false feeling that this function supports
standard gfp flags and callers can pass __GFP_ZERO to get zeroed buffer,
what has already been an issue: see commit dd65a941f6 ("arm64:
dma-mapping: clear buffers allocated with FORCE_CONTIGUOUS flag").
Link: http://lkml.kernel.org/r/20180709122019eucas1p2340da484acfcc932537e6014f4fd2c29~-sqTPJKij2939229392eucas1p2j@eucas1p2.samsung.com
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Michał Nazarewicz <mina86@mina86.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- a series from Robin to fix bus imposed dma limits by adding a separate
mask for them to struct device instead of trying to squeeze a second
meaning out of the existing dma mask as we did before. This has ACKs
from the various other subsystems touched
- a small swiotlb cleanup from Kees (acked by Konrad)
- conversion of nios2 and sh to the new generic dma-noncoherent code.
Various other architecture conversions will come through the
architectures maintainers trees.
-----BEGIN PGP SIGNATURE-----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=WNwP
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.19' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- a series from Robin to fix bus imposed dma limits by adding a
separate mask for them to struct device instead of trying to squeeze
a second meaning out of the existing dma mask as we did before.
This has ACKs from the various other subsystems touched
- a small swiotlb cleanup from Kees (acked by Konrad)
- conversion of nios2 and sh to the new generic dma-noncoherent code.
Various other architecture conversions will come through the
architectures maintainers trees.
* tag 'dma-mapping-4.19' of git://git.infradead.org/users/hch/dma-mapping:
sh: use generic dma_noncoherent_ops
sh: split arch/sh/mm/consistent.c
sh: use dma_direct_ops for the CONFIG_DMA_COHERENT case
sh: introduce a sh_cacheop_vaddr helper
sh: simplify get_arch_dma_ops
OF: Don't set default coherent DMA mask
ACPI/IORT: Don't set default coherent DMA mask
iommu/dma: Respect bus DMA limit for IOVAs
of/device: Set bus DMA mask as appropriate
ACPI/IORT: Set bus DMA mask as appropriate
dma-mapping: Generalise dma_32bit_limit flag
ACPI/IORT: Support address size limit for root complexes
of/platform: Initialise default DMA masks
nios2: use generic dma_noncoherent_ops
swiotlb: clean up reporting
dma-mapping: relax warning for per-device areas
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes & corresponding
regsets to expose DSP ASE & floating point mode state respectively,
both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where it
was previously possible for CPUs to clobber a register value saved
by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which
now sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build failures
for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for systems
where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than MIPSr2
to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW3G6JxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN0n/gD/Rpdgay31G/4eTTKBmBrcaju6Shjt
/2Iu6WC5Sj4hDHUBAJSbuI+B9YjcNsjekBYxB/LLD7ImcLBl6nLMIvKmXLAL
=cUiF
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Here are the main MIPS changes for 4.19.
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes &
corresponding regsets to expose DSP ASE & floating point mode state
respectively, both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where
it was previously possible for CPUs to clobber a register value
saved by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which now
sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build
failures for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for
systems where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than
MIPSr2 to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code"
* tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (123 commits)
MIPS: Remove remnants of UASM_ISA
MIPS: netlogic: xlr: Remove erroneous check in nlm_fmn_send()
MIPS: VDSO: Force link endianness
MIPS: Always specify -EB or -EL when using clang
MIPS: Use dins to simplify __write_64bit_c0_split()
MIPS: Use read-write output operand in __write_64bit_c0_split()
MIPS: Avoid using array as parameter to write_c0_kpgd()
MIPS: vdso: Allow clang's --target flag in VDSO cflags
MIPS: genvdso: Remove GOT checks
MIPS: Remove obsolete MIPS checks for DST node "chosen@0"
MIPS: generic: Remove input symbols from defconfig
MIPS: Delete unused code in linux32.c
MIPS: Remove unused sys_32_mmap2
MIPS: Remove nabi_no_regargs
mips: dts: mscc: enable spi and NOR flash support on ocelot PCB123
mips: dts: mscc: Add spi on Ocelot
MIPS: Loongson: Merge load addresses
MIPS: Loongson: Set Loongson32 to MIPS32R1
MIPS: mscc: ocelot: add interrupt controller properties to GPIO controller
MIPS: generic: Select MIPS_AUTO_PFN_OFFSET
...
Whilst the notion of an upstream DMA restriction is most commonly seen
in PCI host bridges saddled with a 32-bit native interface, a more
general version of the same issue can exist on complex SoCs where a bus
or point-to-point interconnect link from a device's DMA master interface
to another component along the path to memory (often an IOMMU) may carry
fewer address bits than the interfaces at both ends nominally support.
In order to properly deal with this, the first step is to expand the
dma_32bit_limit flag into an arbitrary mask.
To minimise the impact on existing code, we'll make sure to only
consider this new mask valid if set. That makes sense anyway, since a
mask of zero would represent DMA not being wired up at all, and that
would be better handled by not providing valid ops in the first place.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This removes needless use of '%p', and refactors the printk calls to
use pr_*() helpers instead.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
For architectures that do not use per-device dma ops we need to export
the dma_map_ops structure returned from get_arch_dma_ops().
Fixes: 10314e09 ("riscv: add swiotlb support")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Andreas Schwab <schwab@suse.de>
The MIPS bmips platform needs a global flush when transferring ownership
back to the CPU. Add a hook for that to the dma-noncoherent
implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patchwork: https://patchwork.linux-mips.org/patch/19549/
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Tom Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: iommu@lists.linux-foundation.org
Cc: linux-mips@linux-mips.org
Currently the code is split over various files with dma- prefixes in the
lib/ and drives/base directories, and the number of files keeps growing.
Move them into a single directory to keep the code together and remove
the file name prefixes. To match the irq infrastructure this directory
is placed under the kernel/ directory.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Christoph Hellwig