This type is used for traps that trap control packets such as ARP
request and IGMP query to the CPU.
Do not report such packets to the kernel's drop monitor as they were not
dropped by the device no encountered an exception during forwarding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The action is used by control traps such as IGMP query. The packet is
flooded by the device, but also trapped to the CPU in order for the
software bridge to mark the receiving port as a multicast router port.
Such packets are marked with 'skb->offload_fwd_mark = 1' in order to
prevent the software bridge from flooding them again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices capable of offloading the kernel's datapath and perform
functions such as bridging and routing must also be able to send (trap)
specific packets to the kernel (i.e., the CPU) for processing.
For example, a device acting as a multicast-aware bridge must be able to
trap IGMP membership reports to the kernel for processing by the bridge
module.
In most cases, the underlying device is capable of handling packet rates
that are several orders of magnitude higher compared to those that can
be handled by the CPU.
Therefore, in order to prevent the underlying device from overwhelming
the CPU, devices usually include packet trap policers that are able to
police the trapped packets to rates that can be handled by the CPU.
This patch allows capable device drivers to register their supported
packet trap policers with devlink. User space can then tune the
parameters of these policer (currently, rate and burst size) and read
from the device the number of packets that were dropped by the policer,
if supported.
Subsequent patches in the series will allow device drivers to create
default binding between these policers and packet trap groups and allow
user space to change the binding.
v2:
* Add 'strict_start_type' in devlink policy
* Have device drivers provide max/min rate/burst size for each policer.
Use them to check validity of user provided parameters
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On low memory system, run time dumps can consume too much memory. Add
administrator ability to disable auto dumps per reporter as part of the
error flow handle routine.
This attribute is not relevant while executing
DEVLINK_CMD_HEALTH_REPORTER_DUMP_GET.
By default, auto dump is activated for any reporter that has a dump method,
as part of the reporter registration to devlink.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5 PCI PF and VF devlink devices register their ports as
physical port in non-representors mode.
Introduce a new port flavour as virtual so that virtual devices can
register 'virtual' flavour to make it more clear to users.
An example of one PCI PF and 2 PCI virtual functions, each having
one devlink port.
$ devlink port show
pci/0000:06:00.0/1: type eth netdev ens2f0 flavour physical port 0
pci/0000:06:00.2/1: type eth netdev ens2f2 flavour virtual port 0
pci/0000:06:00.3/1: type eth netdev ens2f3 flavour virtual port 0
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow driver to indicate cookie metadata for registered traps.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting the dump's time-stamp, use ktime_get_real in addition to
jiffies. This simplifies the user space implementation and bypasses
some inconsistent behavior with translating jiffies to current time.
The time taken is transformed into nsec, to comply with y2038 issue.
Fixes: c8e1da0bf9 ("devlink: Add health report functionality")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the 'reset_dev_on_drv_probe' devlink parameter, it is useful
to have an unknown value which can be used by drivers to report that the
hardware value isn't recognized or is otherwise invalid instead of
failing the operation.
This is especially useful for u8/enum parameters.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the 'reset_dev_on_drv_probe' devlink parameter, controlling the
device reset policy on driver probe.
This parameter is useful in conjunction with the existing
'fw_load_policy' parameter.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the 'disk' value to the generic 'fw_load_policy' devlink parameter.
This value indicates that firmware should always be loaded from disk
only.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the basic packet trap infrastructure that allows device drivers to
register their supported packet traps and trap groups with devlink.
Each driver is expected to provide basic information about each
supported trap, such as name and ID, but also the supported metadata
types that will accompany each packet trapped via the trap. The
currently supported metadata type is just the input port, but more will
be added in the future. For example, output port and traffic class.
Trap groups allow users to set the action of all member traps. In
addition, users can retrieve per-group statistics in case per-trap
statistics are too narrow. In the future, the trap group object can be
extended with more attributes, such as policer settings which will limit
the amount of traffic generated by member traps towards the CPU.
Beside registering their packet traps with devlink, drivers are also
expected to report trapped packets to devlink along with relevant
metadata. devlink will maintain packets and bytes statistics for each
packet trap and will potentially report the trapped packet with its
metadata to user space via drop monitor netlink channel.
The interface towards the drivers is simple and allows devlink to set
the action of the trap. Currently, only two actions are supported:
'trap' and 'drop'. When set to 'trap', the device is expected to provide
the sole copy of the packet to the driver which will pass it to devlink.
When set to 'drop', the device is expected to drop the packet and not
send a copy to the driver. In the future, more actions can be added,
such as 'mirror'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an eswitch, PCI VF may have port which is normally represented using
a representor netdevice.
To have better visibility of eswitch port, its association with VF,
and its representor netdevice, introduce a PCI VF port flavour.
When devlink port flavour is PCI VF, fill up PCI VF attributes of
the port.
Extend port name creation using PCI PF and VF number scheme on best
effort basis, so that vendor drivers can skip defining their own scheme.
$ devlink port show
pci/0000:05:00.0/0: type eth netdev eth0 flavour pcipf pfnum 0
pci/0000:05:00.0/1: type eth netdev eth1 flavour pcivf pfnum 0 vfnum 0
pci/0000:05:00.0/2: type eth netdev eth2 flavour pcivf pfnum 0 vfnum 1
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an eswitch, PCI PF may have port which is normally represented
using a representor netdevice.
To have better visibility of eswitch port, its association with
PF and a representor netdevice, introduce a PCI PF port
flavour and port attriute.
When devlink port flavour is PCI PF, fill up PCI PF attributes of the
port.
Extend port name creation using PCI PF number on best effort basis.
So that vendor drivers can skip defining their own scheme.
$ devlink port show
pci/0000:05:00.0/0: type eth netdev eth0 flavour pcipf pfnum 0
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a function to be called from drivers during flash. It sends
notification to userspace about flash update progress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename devlink health attributes for better reflect the attributes use.
Add COUNT prefix on error counter attribute and recovery counter
attribute.
Fixes: 7afe335a8b ("devlink: Add health get command")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink flash update command. Advanced NICs have firmware
stored in flash and often cryptographically secured. Updating
that flash is handled by management firmware. Ethtool has a
flash update command which served us well, however, it has two
shortcomings:
- it takes rtnl_lock unnecessarily - really flash update has
nothing to do with networking, so using a networking device
as a handle is suboptimal, which leads us to the second one:
- it requires a functioning netdev - in case device enters an
error state and can't spawn a netdev (e.g. communication
with the device fails) there is no netdev to use as a handle
for flashing.
Devlink already has the ability to report the firmware versions,
now with the ability to update the firmware/flash we will be
able to recover devices in bad state.
To enable updates of sub-components of the FW allow passing
component name. This name should correspond to one of the
versions reported in devlink info.
v1: - replace target id with component name (Jiri).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink fmsg is a mechanism to pass descriptors between drivers and
devlink, in json-like format. The API allows the driver to add nested
attributes such as object, object pair and value array, in addition to
attributes such as name and value.
Driver can use this API to fill the fmsg context in a format which will be
translated by the devlink to the netlink message later.
There is no memory allocation in advance (other than the initial list
head), and it dynamically allocates messages descriptors and add them to
the list on the fly.
When it needs to send the data using SKBs to the netlink layer, it
fragments the data between different SKBs. In order to do this
fragmentation, it uses virtual nests attributes, to avoid actual
nesting use which cannot be divided between different SKBs.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shared buffer allocation is usually done in cell increments.
Drivers will either round up the allocation or refuse the
configuration if it's not an exact multiple of cell size.
Drivers know exactly the cell size of shared buffer, so help
out users by providing this information in dumps.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i has a few fixed-size fields which can be used to report
firmware version and expansion ROM version. Unfortunately, modern
hardware has more firmware components. There is usually some
datapath microcode, management controller, PXE drivers, and a
CPLD load. Running ethtool -i on modern controllers reveals the
fact that vendors cram multiple values into firmware version field.
Here are some examples from systems I could lay my hands on quickly:
tg3: "FFV20.2.17 bc 5720-v1.39"
i40e: "6.01 0x800034a4 1.1747.0"
nfp: "0.0.3.5 0.25 sriov-2.1.16 nic"
Add a new devlink API to allow retrieving multiple versions, and
provide user-readable name for those versions.
While at it break down the versions into three categories:
- fixed - this is the board/fixed component version, usually vendors
report information like the board version in the PCI VPD,
but it will benefit from naming and common API as well;
- running - this is the running firmware version;
- stored - this is firmware in the flash, after firmware update
this value will reflect the flashed version, while the
running version may only be updated after reboot.
v3:
- add per-type helpers instead of using the special argument (Jiri).
RFCv2:
- remove the nesting in attr DEVLINK_ATTR_INFO_VERSIONS (now
versions are mixed with other info attrs)l
- have the driver report versions from the same callback as
other info.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -i has served us well for a long time, but its showing
its limitations more and more. The device information should
also be reported per device not per-netdev.
Lay foundation for a simple devlink-based way of reading device
info. Add driver name and device serial number as initial pieces
of information exposed via this new API.
v3:
- rename helpers (Jiri);
- rename driver name attr (Jiri);
- remove double spacing in commit message (Jiri).
RFC v2:
- wrap the skb into an opaque structure (Jiri);
- allow the serial number of be any length (Jiri & Andrew);
- add driver name (Jonathan).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add notification call for devlink port param set, register and unregister
functions.
Add devlink_port_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
v7->v8:
Order devlink_port_param_value_changed() definitions followed by
devlink_param_value_changed()
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port param set command to set the value for a parameter.
Value can be set to any of the supported configuration modes.
v7->v8: Append "Acked-by: Jiri Pirko <jiri@mellanox.com>"
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port param get command which gets data per parameter.
It also has option to dump the parameters data per port.
v7->v8: Append "Acked-by: Jiri Pirko <jiri@mellanox.com>"
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the buffer descriptors API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink health buffer is a mechanism to pass descriptors between drivers
and devlink. The API allows the driver to add objects, object pair,
value array (nested attributes), value and name.
Driver can use this API to fill the buffers in a format which can be
translated by the devlink to the netlink message.
In order to fulfill it, an internal buffer descriptor is defined. This
will hold the data and metadata per each attribute and by used to pass
actual commands to the netlink.
This mechanism will be later used in devlink health for dump and diagnose
data store by the drivers.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers load the device's firmware image during the initialization
flow either from the flash or from the disk. Currently this option is not
controlled by the user and the driver decides from where to load the
firmware image.
'fw_load_policy' gives the ability to control this option which allows the
user to choose between different loading policies supported by the driver.
This parameter can be useful while testing and/or debugging the device. For
example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_READ_GET used for both reading
and dumping region data. Read allows reading from a region specific
address for given length. Dump allows reading the full region.
If only snapshot ID is provided a snapshot dump will be done.
If snapshot ID, Address and Length are provided a snapshot read
will done.
This is used for both snapshot access and will be used in the same
way to access current data on the region.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_DEL used
for deleting a snapshot from a region. The snapshot ID is required.
Also added notification support for NEW and DEL of snapshots.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support for DEVLINK_CMD_REGION_GET command to also
return the IDs of the snapshot currently present on the region.
Each reply will include a nested snapshots attribute that
can contain multiple snapshot attributes each with an ID.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_GET command which is used for
querying for the supported DEV/REGION values of devlink devices.
The support is both for doit and dumpit.
Reply includes:
BUS_NAME, DEVICE_NAME, REGION_NAME, REGION_SIZE
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink_param_notify() function to support devlink param notifications.
Add notification call to devlink param set, register and unregister
functions.
Add devlink_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add param set command to set value for a parameter.
Value can be set to any of the supported configuration modes.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add param get command which gets data per parameter.
Option to dump the parameters data per device.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define configuration parameters data structure.
Add functions to register and unregister the driver supported
configuration parameters table.
For each parameter registered, the driver should fill all the parameter's
fields. In case the only supported configuration mode is "driverinit"
the parameter's get()/set() functions are not required and should be set
to NULL, for any other configuration mode, these functions are required
and should be set by the driver.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink ports can have specific flavour according to the purpose of use.
This patch extend attrs_set so the driver can say which flavour port
has. Initial flavours are:
physical, cpu, dsa
User can query this to see right away what is the purpose of each port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware processes which are modeled via dpipe commonly use some
internal hardware resources. Such relation can improve the understanding
of hardware limitations. The number of resource's unit consumed per
table's entry are also provided for each table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel