Transitional drivers might access the NULL pointer plane->state in
drm_helper_crtc_mode_set_base(), which causes NULL pointer dereference.
So, let's reset it before handing it over to those drivers.
commit e4f31ad2b7 ("drm: reset empty state in transitional helpers")
did the same thing for other transitional helpers, but it seems this one
was missed.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459846239-8946-1-git-send-email-gnuiyl@gmail.com
We started to use PIPE_CONTROL to write render ring seqno in order to
combat seqno write vs interrupt generation problems. This was introduced
by commit 7c17d37737 ("drm/i915: Use ordered seqno write interrupt
generation on gen8+ execlists").
On gen8+ size of PIPE_CONTROL with Post Sync Operation should be
6 dwords. When we're using older 5-dword variant it's possible to
observe inconsistent values written by PIPE_CONTROL with Post
Sync Operation from user batches, resulting in rendering corruptions.
v2: Fix BAT failures
v3: Comments on alignment and thrashing high dword of seqno (Chris)
v4: Updated commit msg (Mika)
Testcase: igt/gem_pipe_control_store_loop/*-qword-write
Issue: VIZ-7393
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460469115-26002-1-git-send-email-michal.winiarski@intel.com
Experiments with heaven 4.0 benchmark and skylake gt3e (rev 0xa)
suggest that WaForceContextSaveRestoreNonCoherent is needed for all
revs. Extending this to all revs cures a gpu hang with rev 0xa when
running heaven4.0 gpu benchmark.
We have been here before, with problems enabling gt4e and extending
up to revision F0 instead of false claims of bspec of E0 only. See
commit <e238659ddd88> ("drm/i915/skl: Default to noncoherent access
up to F0"). In retrospect we should have covered this with this big
blanket back then already, as E0 vs F0 discrepancy was suspicious
enough.
Previously the WaForceEnableNonCoherent has been tied to
context non-coherence, atleast in relevant hsds. So keep this tie
and extended this alongside.
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: stable@vger.kernel.org
Reported-by: Mike Lothian <mike@fireburn.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=93491
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-2-git-send-email-mika.kuoppala@intel.com
For all gt3 and gt4 skylake variants, extend the usage of
WaRsDisableCoarsePowerGating for all revisions. Without this
gt3 and gt4 skylakes up to atleast rev 0xa can gpu hang or
system hang.
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Ben Widawsky <benjamin.widawsky@intel.com>
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: <stable@vger.kernel.org>
Reported-by: Mikael Djurfeldt <mikael@djurfeldt.com>
References: https://bugs.freedesktop.org/show_bug.cgi?id=94161
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <benjamin.widawsky@intel.com>
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459860977-27751-1-git-send-email-mika.kuoppala@intel.com
We can use the new pin/lazy unpin API for simplicity
and more performance in the execlist submission paths.
v2:
* Fix error handling and convert more users.
* Compact some names for readability.
v3:
* intel_lr_context_free was not unpinning.
* Special case for GPU reset which otherwise unbalances
the HWS object pages pin count by running the engine
initialization only (not destructors).
v4:
* Rebased on top of hws setup/init split.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460472042-1998-1-git-send-email-tvrtko.ursulin@linux.intel.com
[tursulin: renames: s/hwd/hws/, s/obj_addr/vaddr/]
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Split the hardware status page into setup and initialisation,
where setup means setting up the driver state to support the
engine, and initialization means programming the hardware
with the before set up state.
This way the design matches the design of the engine setup/init
code which is split in the same fashion and it enables the
stages to be used in a balanced fashion (engine setup - hws
setup, engine init - hws init).
This will enable the upcoming improvements to slot in without
any kludges on the GPU reset path.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Check whether the DPLL is even enabled before readoing out the dividers
and trying to derive port_clock on CHV. We already did this on VLV.
Also remove the comment "MIPI" comment from the VLV code since we call
this function whenever the pipe is enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
On VLV at least, the BIOS may leave the DSI PLL enabled in some wonky
state where it just refuses to lock. Simply disabling the PLL before
reconfiguring it is not enough to fix it, but power gating the PLL
prior to reconfiguring does work.
This happens on BYT FFRD8 when booting with HDMI connected so the DSI
display will not be lit up by the BIOS.
Also we can remove the code for BXT that disables the PLL before
enabling it again.
v2: s/vlv/intel/ since BXT made thing generic
v3: Remove the BXT disable PLL before enable trick
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-11-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.
It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.
MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
For a bit of extra paranoia make sure the display irqs are all cleared
before we enabled them when turning on the power well. This should
really be the case already since the power well was off which resets
everything.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
During runtime PM we'll be reinitializing interrupt support from the
ground up. However since the display power well will be off at that
time, well end up with a ton of unclaimed register accesses from the
display irq setup. Since we turned off the power well already before
runtime suspend, we've flagged display irqs as disabled during runtime
PM transitions. So we can just check that flag to see if we should do
skip display irqs during irq setup.
During driver load display irqs will be flagged as enabled since we've
turned on the power well already, however the power well code will have
skipped the display irq setup since irq support as a whole wasn't yet
enabled when the power well was enabled. So we'll want to do the display
irq setup in that case.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The vlv/chv display irq setup was a bit of mess after I ran out of steam
when working on it last. Fix it up so that we just have a _reset() and
_postinstall() hooks for the display irqs, and use those consistently.
v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in
vlv_display_irq_reset() (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460476574-1921-1-git-send-email-ville.syrjala@linux.intel.com
The underruns we were seeing when enabling eDP port A on ILK seem to
have been caused by prematurely clearing the LP1+ watermark values when
disabling LP1+ watermarks. Now that the watermarks are handled
properly, we can rip out the underrun suppression around the port A
enable.
We still need to worry about the underruns on FDI when enabling
the eDP PLL. But as Bspec tells us, we can avoid that by a vblank
wait on the pipe driving FDI just prior to enabling the eDP PLL.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Once again ILK is unhappy if we clear out the LP1+ watermark levels
outright, and instead we must disable the levels we don't want while
still leaving the actual programmed watermark levels intact.
Fixes underruns on the already enabled pipe when programming watermarks
while enabling the second pipe.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Take a bigger hammer to the underrun suppression on ILK. Instead of
trying to suppress them at specific points in the modeset sequence just
silence them across the entire sequence. This gets rid of some underruns
at least on my ILK. Note that this changes SNB and IVB to follow the
same approach just to keep the code less convoluted. The difference is
that on those platforms we won't suppress CPU underruns for port A since
it doesn't seem to be necessary.
My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is
as effective on other PCH port types. Perhaps we still need some of
Daniel's extra vblank waits [2]?
I've still been able to trigger an underrun on the other pipe, but
fixing that perhaps needs the LP1+ disable trick I implemented here [1]
which never got merged.
A few details which hamper stress testing on my ILK are that sometimes
the PCH transcoder gets messed up and refuses to shut down, and sometimes
even the panel power sequencer apparently gets stuck on the always on
position.
[1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html
[2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html
v2: Add a note that we also get underruns when enabling PCH ports
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Rather than blindly waking up all forcewake domains on command
submission, we can teach each engine what is (or are) the correct
one to take.
On platforms with multiple forcewake domains like VLV, CHV, SKL
and BXT, this has the potential of lowering the GPU and CPU
power use and submission latency.
To implement it we add a function named
intel_uncore_forcewake_for_reg whose purpose is to query which
forcewake domains need to be taken to read or write a specific
register with raw mmio accessors.
These enables the execlists engine setup to query which
forcewake domains are relevant per engine on the currently
running platform.
v2:
* Kerneldoc.
* Split from intel_uncore.c macro extraction, WARN_ON,
no warns on old platforms. (Chris Wilson)
v3:
* Single domain per engine, mention all registers,
bi-directional function and a new name, fix handling
of gen6 and gen7 writes. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460468251-14069-1-git-send-email-tvrtko.ursulin@linux.intel.com
Chris Wilson points out that we can remove them from the array
since they are always written to with raw accessors.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Knowledge of which register per platform belonds in which
forcewake domain was embedded in the MMIO accessors themselves.
Extract it into standalone macros so they can be used from
new code in the following patches.
This causes GCC to compile some of the MMIO accessors slightly
differently and grows the code a tiny amount. But none of the
growth is on the fast-path so it does not matter hugely.
Affected sizes before:
00000000000026f0 00000000000001a5 t gen6_read16
0000000000002390 00000000000001a5 t gen6_read32
00000000000028a0 00000000000001a5 t gen6_read64
00000000000061d0 000000000000019e t gen8_write16
0000000000006510 000000000000019d t gen8_write32
0000000000006370 000000000000019d t gen8_write64
00000000000021f0 000000000000019d t gen8_write8
Affected sizes after:
0000000000002840 00000000000001aa t gen6_read16
00000000000024e0 00000000000001a9 t gen6_read32
00000000000029f0 00000000000001a9 t gen6_read64
0000000000004f20 00000000000001b5 t gen8_write16
0000000000004ba0 00000000000001b4 t gen8_write32
00000000000050e0 00000000000001b4 t gen8_write64
0000000000004d60 00000000000001b4 t gen8_write8
Other MMIO accessors are not affected in size.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
As the vast majority of users do not use the domain id variable,
we can eliminate it from the iterator and also change the latter
using the same principle as was recently done for for_each_engine.
For a couple of callers which do need the domain mask, store it
in the domain array (which already has the domain id), then both
can be retrieved thence.
Result is clearer code and smaller generated binary, especially
in the tight fw get/put loops. Also, relationship between domain
id and mask is no longer assumed in the macro.
v2: Improve grammar in the commit message and rename the
iterator to for_each_fw_domain_masked for consistency.
(Dave Gordon)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Because it is based on jiffies, current implementation releases the
forcewake at any time between straight away and between 1ms and 10ms,
depending on the kernel configuration (CONFIG_HZ).
This is probably not what has been desired, since the dynamics of keeping
parts of the GPU awake should not be correlated with this kernel
configuration parameter.
Change the auto-release mechanism to use hrtimers and set the timeout to
1ms with a 1ms of slack. This should make the GPU power consistent
across kernel configs, and timer slack should enable some timer coalescing
where multiple force-wake domains exist, or with unrelated timers.
For GlBench/T-Rex this decreases the number of forcewake releases from
~480 to ~300 per second, and for a heavy combined OGL/OCL test from
~670 to ~360 (HZ=1000 kernel).
Even though this reduction can be attributed to the average release period
extending from 0-1ms to 1-2ms, as discussed above, it will make the
forcewake timeout consistent for different CONFIG_HZ values.
Real life measurements with the above workload has shown that, with this
patch, both manage to auto-release the forcewake between 2-4 times per
10ms, even though the number of forcewake gets is dramatically different.
T-Rex requests between 5-10 explicit gets and 5-10 implict gets in each
10ms period, while the OGL/OCL test requests 250 and 380 times in the same
period.
The two data points together suggest that the nature of the forwake
accesses is bursty and that further changes and potential timeout
extensions, or moving the start of timeout from the first to the last
automatic forcewake grab, should be carefully measured for power and
performance effects.
v2:
* Commit spelling. (Dave Gordon)
* More discussion on numbers in the commit. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Only really needed for fbdev emulation at 8bpp. And bochs doesn't do
that. And either way bochs only does 32bit rgb, so this is all pretty
much wasted dead code.
The only consideration is that we need to not set up any gamma size
either.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-5-git-send-email-daniel.vetter@ffwll.ch
__drm_atomic_helper_plane_destroy_state calls
drm_framebuffer_unreference, which means that if drm_framebuffer_free
is called before plane->destroy freed memory will be accessed.
A similar case happens for the blob list, which was freed before the
crtc state was, resulting in the unreference_blob from crtc_destroy_state
pointing to garbage memory causing another opportunity for a GPF.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458657734-21866-1-git-send-email-maarten.lankhorst@linux.intel.com
We've had problems on several occasions with using the panel type
from the VBT block 40. Usually it seems to be 2, which often
doesn't give us the correct timings for the panel. After some
more digging I found a way to get a panel type via the OpRegion
SWSCI GBDA "Get Panel Details" method. Let's try to use it.
The spec has this to say about the output:
"Bits [15:8] - Panel Type
Bits contain the panel type user setting from CMOS
00h = Not Valid, use default Panel Type & Timings from VBT
01h - 0Fh = Panel Number"
Another version of the spec lists the valid range as 1-16, which makes
more sense since VBT supports 16 panels. Based on actual results
from Rob's G45, 1-16 is what we need to accept.
The other bits in the output don't look relevant for the problem at
hand.
The input is specified as:
"Bits [31:4] - Reserved
Reserved (must be zero)
Bits [3:0] - Panel Number
These bits contain the sequential index of Panel, starting at 0 and
counting upwards from the first integrated Internal Flat-Panel Display
Encoder present, and then from the first external Display Encoder
(e.g., S/DVO-B then S/DVO-C) which supports Internal Flat-Panels.
0h - 0Fh = Panel number"
For now I've just hardcoded the input panel number as 0. That would seem
like a decent choise for LVDS. Not so sure about eDP when port != A.
v2: Accept values 1-16
Filter out bogus results in opregion code (Jani)
Add debug logging for all the different branches (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rob Kramer <rob@solution-space.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94825
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460359431-11003-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Rob Kramer <rob@solution-space.com>
Store the extracted panel_type under dev_priv.vbt instead of keeping
around a static variable for it.
Cc: Rob Kramer <rob@solution-space.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
VBT can only contain 16 panel entries, indexed with the panel_type.
To play it safe we should reject panel_type > 0xf, so that we don't
read past the valid data.
v2: Add debug logging (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rob Kramer <rob@solution-space.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460359329-10817-1-git-send-email-ville.syrjala@linux.intel.com
When the GMBUS based i2c transfer times out, we try to fall back to
bit-banging and retry the operation that way. However if the bit-banging
attempt also fails, we should probably go back to the GMBUS method for
the next attempt. Maybe there simply wasn't anyone one the bus at this
time.
There's also a bit of a mess going on with the force_bit handling.
It's supposed to be a ref count actually, and it is as far as
intel_gmbus_force_bit() is concerned. But it's treated as just a
flag by the timeout based bit-banging fallback. I suppose that's
fine since we should never end up in the timeout fallback case
if force_bit was already non-zero. However now that we want to restore
things back to where they were after the bit-banging attempt failed,
we're going to have to do things a bit differently to avoid clobbering
the force_bit count as set up by intel_gmbus_force_bit(). So let's
dedicate the high bit as a flag for the low level timeout based fallback
and treat the rest of the bits as a ref count just as before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Extend the protection of gmbus_mutex around the force_bit
RMW in intel_gmbus_force_bit(), in case someone gets the
idea of calling it from a separate thread while there's
other stuff happening on the same bus.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Since we only ever use the drm_i915_private from the stored
i915_mm_struct->dev, save some electrons by storing the right
backpointer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-3-git-send-email-chris@chris-wilson.co.uk
Holding a reference to the containing task_struct is not sufficient to
prevent the mm_struct from being reaped under memory pressure. If this
happens whilst we are calling get_user_pages(), explosions erupt -
sometimes an immediate GPF, sometimes page flag corruption. To prevent
the target mm from being reaped as we are reading from it, acquire a
reference before we begin.
Testcase: igt/gem_shrink/*userptr
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-2-git-send-email-chris@chris-wilson.co.uk
In order to ensure that all invalidations are completed before the
operation returns to userspace (i.e. before the munmap() syscall returns)
we need to wait upon the outstanding operations.
We are allowed to block inside the invalidate_range_start callback, and
as struct_mutex is the inner lock with mmap_sem we can wait upon the
struct_mutex without provoking lockdep into warning about a deadlock.
However, we don't actually want to wait upon outstanding rendering
whilst holding the struct_mutex if we can help it otherwise we also
block other processes from submitting work to the GPU. So first we do a
wait without the lock and then when we reacquire the lock, we double
check that everything is ready for removing the invalidated pages.
Finally to wait upon the outstanding unpinning tasks, we create a
private workqueue as a means to conveniently wait upon all at once. The
drawback is that this workqueue is per-mm, so any threads concurrently
invalidating objects will wait upon each other. The advantage of using
the workqueue is that we can wait in parallel for completion of
rendering and unpinning of several objects (of particular importance if
the process terminates with a whole mm full of objects).
v2: Apply a cup of tea to the changelog.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94699
Testcase: igt/gem_userptr_blits/sync-unmap-cycles
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459864801-28606-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXCva8AAoJEHm+PkMAQRiGXBoIAIkrjxdbuT2nS9A3tHwkiFXa
6/Th1UjbNaoLuZ+MckQHayAD9NcWY9lVjOUmFsSiSWMCQK/rTWDl8x5ITputrY2V
VuhrJCwI7huEtu6GpRaJaUgwtdOjhIHz1Ue2MCdNIbKX3l+LjVyyJ9Vo8rruvZcR
fC7kiivH04fYX58oQ+SHymCg54ny3qJEPT8i4+g26686m11hvZLI3UAs2PAn6ut+
atCjxdQ4yLN3DWsbjuA7wYGWhTgFloxL4TIoisuOUc3FXnSi/ivIbXZvu4lUfisz
LA2JBhfII3AEMBWG9xfGbXPijJTT4q7yNlTD0oYcnMtAt/Roh2F04asqB1LetEY=
=bri6
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc3' into drm-intel-next-queued
Linux 4.6-rc3
Backmerge requested by Chris Wilson to make his patches apply cleanly.
Tiny conflict in vmalloc.c with the (properly acked and all) patch in
drm-intel-next:
commit 4da56b99d9
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Apr 4 14:46:42 2016 +0100
mm/vmap: Add a notifier for when we run out of vmap address space
and Linus' tree.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
If we want a contiguous mapping of a single page sized object, we can
forgo using vmap() and just use a regular kmap(). Note that this is only
suitable if the desired pgprot_t is compatible.
v2: Use is_vmalloc_addr()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-7-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
I have instances where I want to use drm_malloc_ab() but with a custom
gfp mask. And with those, where I want a temporary allocation, I want to
try a high-order kmalloc() before using a vmalloc().
So refactor my usage into drm_malloc_gfp().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: dri-devel@lists.freedesktop.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-6-git-send-email-chris@chris-wilson.co.uk
When called because we have run out of vmap address space, we only need
to recover objects that have vmappings and not all.
v2: Start using is_vmalloc_addr()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-5-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
We now have two implementations for vmapping a whole object, one for
dma-buf and one for the ringbuffer. If we couple the mapping into the
obj->pages lifetime, then we can reuse an obj->mapping for both and at
the same time couple it into the shrinker. There is a third vmapping
routine in the cmdparser that maps only a range within the object, for
the time being that is left alone, but will eventually use these routines
in order to cache the mapping between invocations.
v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala)
v3: Call unpin_vmap from the right dmabuf unmapper
v4: Rename vmap to map as we don't wish to imply the type of mapping
involved, just that it contiguously maps the object into kernel space.
Add kerneldoc and lockdep annotations
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-4-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
After we pin the ringbuffer into the GGTT, all error paths need to unpin
it again. Move this common step into one block, and make the unable to
iomap error code consistent (i.e. treat it as out of memory to avoid
confusing it with a invalid argument).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-3-git-send-email-chris@chris-wilson.co.uk
We only need the struct_mutex to manipulate the pages_pin_count on the
object, we do not need to hold our BKL when freeing the exported
scatterlist.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-2-git-send-email-chris@chris-wilson.co.uk
This is to fix a GPU hang seen with mid thread pre-emption
and pooled EUs.
v2. Use IS_BXT_REVID instead of IS_BROXTON and INTEL_REVID
v3. And use correct type for register addresses
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571049-854-1-git-send-email-tim.gore@intel.com
For BXT, description of polarities of PORT_PLL_REF_SEL
has been reversed for newer Gen9LP steppings according to the
recent update in Bspec. This bit now should be set for
"Non-SSC" mode for all Gen9LP starting from B0 stepping.
v2: Only B0 and newer stepping should be affected by this
change.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94866
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458176773-26925-1-git-send-email-dongwon.kim@intel.com
Check functions are used by atomic to see if the new state will
be allowed. There's also a hw state checker which checks afterwards
that the committed state is correct. Rename it to hw state verifier
to reduce some confusion.
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56FB8785.8020506@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The modeset state verifier no longer has full access to the hardware,
instead it should only verify affected crtc's.
Looking for disabled stuff can be verified immediately after all crtc
disables have completed, while each enabled crtc can be verified right
after being enabled.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: check -> verify]
This will make it easier to keep the crtc checker when atomic
commit is reworked for asynchronous commits. This prevents checking
crtc's that were not part of the state. It's safe to verify disabled
encoders, connectors and dpll's that are not part of the state,
because during modeset connection_mutex is held.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Extend commit message and rename check to verify.]
When reading from the HWS page, we use barrier() to prevent the compiler
optimising away the read from the volatile (may be updated by the GPU)
memory address. This is more suited to READ_ONCE(); make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-5-git-send-email-chris@chris-wilson.co.uk
Rather than call a function to compute the matching cachelines and
clflush them, just call the clflush *instruction* directly. We also know
that we can use the unpatched plain clflush rather than the clflushopt
alternative.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-4-git-send-email-chris@chris-wilson.co.uk
Only declare a missed interrupt if we find that the GPU is idle with
waiters and a hangcheck interval has passed in which no new user
interrupts have been raised.
v2: Clear the stuck interrupt marker between successful batches
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-3-git-send-email-chris@chris-wilson.co.uk
In order to simplify future patches, extract the
lazy_coherency optimisation our of the engine->get_seqno() vfunc into
its own callback.
v2: Rename the barrier to engine->irq_seqno_barrier to try and better
reflect that the barrier is only required after the user interrupt before
reading the seqno (to ensure that the seqno update lands in time as we
do not have strict seqno-irq ordering on all platforms).
Reviewed-by: Dave Gordon <david.s.gordon@intel.com> [#v2]
v3: Comments for hangcheck paranoia. Mika wanted to keep the extra
barrier inside the hangcheck, just in case. I can argue that it doesn't
provide a barrier against anything, but the side-effects of applying the
barrier may prevent a false declaration of a hung GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-2-git-send-email-chris@chris-wilson.co.uk
In order to ensure seqno/irq coherency, we currently read a ring register.
The mmio transaction following the interrupt delays the inspection of
the seqno long enough for the MI_STORE_DWORD_IMM to update the CPU
cache. However, it is only the memory timing that is important for the
purposes of the delay, we do not need nor desire the extra forcewake.
v3: Update commentary
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> [v2]
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-1-git-send-email-chris@chris-wilson.co.uk
Currently for the case where there is enough space at the end of Ring
buffer for accommodating only the base request, the wrapround is done
immediately and as a result the base request gets added at the start
of Ring buffer. But there may not be enough free space at the beginning
to accommodate the base request, as before the wraparound, the wait was
effectively done for the reserved_size free space from the start of
Ring buffer. In such a case there is a potential of Ring buffer overflow,
the instructions at the head of Ring (ACTHD) can get overwritten.
Since the base request can fit in the remaining space, there is no need
to wraparound immediately. The wraparound will anyway happen later when
the reserved part starts getting used.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1457688402-10411-1-git-send-email-akash.goel@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Both cases produce the same result. Kill the junk code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Fix possible out of bounds read, by adding missing comma.
The code may read pass the end of the dsi_errors array
when the most significant bit (bit #31) in the intr_stat register
is set.
This bug has been detected using CppCheck (static analysis tool).
Cc: stable@vger.kernel.org
Signed-off-by: Itai Handler <itai_handler@hotmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We are allocating backing using psbfb_alloc() and so
backing->stolen is always true. So we were freeing backing two times.
Moreover if we follow the execution path then we should be freeing
backing after we have released the helper. So remove the one which frees
backing before the helper is released.
While at it the error labels are also renamed to give a meaningful
name.
[Patrik: Fixed conflict with removal of struct_mutex]
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Having fixed the tracking of the engine's last_submitted_seqno, we can
now rely on it for detecting when the engine is idle (and not have to
touch the requests pointer).
Testcase: igt/gem_exec_whisper
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-9-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Seal the request and mark it as pending execution before we submit it to
hardware. We assume that the actual submission cannot fail (that
guarantee is provided by preallocating space in the request for the
submission). As we may inspect this state without holding any locks
during hangcheck we should apply a barrier to ensure that we do
not see a more recent value in the HWS than we are tracking.
Based on a patch by Mika Kuoppala.
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-8-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
When we change the current seqno, we also need to remember to reset the
last_submitted_seqno for the engine.
Testcase: igt/gem_exec_whisper
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-7-git-send-email-chris@chris-wilson.co.uk
An oversight is that when we wrap the seqno, we need to reset the hw
semaphore counters to 0. We did this for gen6 and gen7 and forgot to do
so for the new implementation required for gen8 (legacy).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-6-git-send-email-chris@chris-wilson.co.uk
Since we are setting engine local values that are tied to the hardware,
move it out of i915_gem_init_seqno() into the intel_ring_init_seqno()
backend, next to where the other hw semaphore registers are written.
v2: Make the explanatory comment about always resetting the semaphores to
0 irrespective of the value of the reset seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-4-git-send-email-chris@chris-wilson.co.uk
We only use drm_i915_private within the function, so delete the unneeded
drm_device local.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-3-git-send-email-chris@chris-wilson.co.uk
After the GPU reset and we discard all of the incomplete requests, mark
the GPU as having advanced to the last_submitted_seqno (as having
completed the requests and ready for fresh work). The impact of this is
negligible, as all the requests will be considered completed by this
point, it just brings the HWS into line with expectations for external
viewers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-2-git-send-email-chris@chris-wilson.co.uk
It's useful to look at the last seqno submitted on a particular engine
and compare it against the HWS value to check for irregularities.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-1-git-send-email-chris@chris-wilson.co.uk
At BXT DSI, PIPE registers are inactive. So we can't get the
PIPE's mode parameters from them. The possible option is
retriving them from the PORT registers.
The required changes are added for BXT in intel_dsi_get_config
(encoder->get_config).
v2: Addressed the Jani's comments
-removed the redundant call to encoder->get_config
-read bpp from port register
-removed retrival of src_size from encoder->get_config
v3: pipe_config->pipe_bpp is fixed
Jani's review comments addressed:
Few horizontal timing parameters dropped from the patch to make
progress, as there seems to be some disagreement on
best/feasible/possible options.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Previously Reviewed at: https://lists.freedesktop.org/archives/intel-gfx/2016-April/091737.html
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460019967-26501-2-git-send-email-ramalingam.c@intel.com
Define and store the pad base offset in the array, and reference the
pconf0 and padval registers through macros. Add VLV prefixes to
macros. Use spec nomenclature for pconf0 and padval.
v2: Address Ville's review comments, squash another patch here.
v3: Use the names Ville dug up in the specs.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/34932140b78a3de7f825c78380a08c930694651b.1459884518.git.jani.nikula@intel.com
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
According to Chris, use of i915_vm_to_ppgtt is visible in benchmark
unless WARN_ON is removed, so lets get rid of it.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Looks much better without container_of everywhere.
v2:
- In i915_gem_restore_gtt_mappings too (Chris)
v3:
- Do not cause WARN by calling on non PPGTT object (Chris)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Lots of misc bug fixes for radeon and amdgpu and one for ttm.
- fix vram info fetching on Fiji and unposted boards
- additional vblank fixes from the conversion to drm_vblank_on/off
- UVD dGPU suspend and resume fixes
- lots of powerplay fixes
- fix a fence leak in the pageflip code
- ttm fix for platforms where CPU is 32 bit, but physical addresses are >32bits
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
drm/amd/powerplay: notify amdgpu whether dpm is enabled or not.
drm/amdgpu: Not support disable dpm in powerplay.
drm/amdgpu: add an cgs interface to notify amdgpu the dpm state.
...
intel_update_max_cdclk() doesn't have a switch case for Broxton, so
dev_priv->max_cdclk_freq gets set to whatever clock frequency we're
currently running at (e.g., 144 MHz) rather than the true maximum. This
causes our max dotclock to also be set too low and in turn leads mode
verification to reject perfectly valid modes while loading EDID firmware
blobs.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459892239-14041-1-git-send-email-matthew.d.roper@intel.com
This patch sets the invert bit for hpd detection for each port
based on VBT configuration. Since each AOB can be designed to
depend on invert bit or not, it is expected if an AOB requires
invert bit, the user will set respective bit in VBT.
v2: Separated VBT parsing from the rest of the logic. (Jani)
v3: Moved setting invert bit logic to bxt_hpd_irq_setup()
and changed its logic to avoid looping twice. (Ville)
v4: Changed the logic to mask out the bits first and then
set them to remove need of temporary variable. (Ville)
v5: Moved defines to existing set of defines for the register
and added required breaks. (Ville)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some checkpatch noise, added kernel-doc.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459420907-11383-2-git-send-email-shubhangi.shrivastava@intel.com
This patch adds new fields that are not yet added in drm code
in child devices struct
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459420907-11383-1-git-send-email-shubhangi.shrivastava@intel.com
Just a single fix to prevent GM20B systems hanging at boot.
* 'linux-4.6' of git://github.com/skeggsb/linux:
drm/nouveau/tegra: acquire and enable reference clock if needed
GM20B requires an extra clock compared to GK20A. Add that information
into the platform data and acquire and enable this clock if necessary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
- Check whether plane parameters comply with IPU IDMAC limitations and
fix planar YUV 4:2:0 U/V offsets and stride
- Cleanup encoder in dw_hdmi-imx bind error path and
remove a superfluous platform_set_drvdata in dw_hdmi-imx
- DMFC setup fixes: lock the ipu_dmfc_init_channel function against
concurrent use, rename it to ipu_dmfc_config_wait4eot, and call
it after the FIFO size has been determined.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3/Gi
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-next-2016-04-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm: stricter plane parameter checking, dw_hdmi-imx and dmfc fixes
- Check whether plane parameters comply with IPU IDMAC limitations and
fix planar YUV 4:2:0 U/V offsets and stride
- Cleanup encoder in dw_hdmi-imx bind error path and
remove a superfluous platform_set_drvdata in dw_hdmi-imx
- DMFC setup fixes: lock the ipu_dmfc_init_channel function against
concurrent use, rename it to ipu_dmfc_config_wait4eot, and call
it after the FIFO size has been determined.
* tag 'imx-drm-next-2016-04-01' of git://git.pengutronix.de/git/pza/linux:
drm/imx: Don't set a gamma table size
drm/imx: ipuv3-plane: Configure DMFC wait4eot bit after slots are determined
gpu: ipu-v3: ipu-dmfc: Rename ipu_dmfc_init_channel to ipu_dmfc_config_wait4eot
gpu: ipu-v3: ipu-dmfc: Make function ipu_dmfc_init_channel() return void
gpu: ipu-v3: ipu-dmfc: Protect function ipu_dmfc_init_channel() with mutex
drm/imx: dw_hdmi: Don't call platform_set_drvdata()
drm/imx: dw_hdmi: Call drm_encoder_cleanup() in error path
drm/imx: ipuv3-plane: fix planar YUV 4:2:0 support
drm/imx: ipuv3-plane: Add more thorough checks for plane parameter limitations
gpu: ipu-cpmem: modify ipu_cpmem_set_yuv_planar_full for better control
- VBT code refactor for a clean split between parsing&using of firmware
information (Jani)
- untangle the pll computation code, and splitting up the monster
i9xx_crtc_compute_clocks (Ander)
- dsi support for bxt (Jani, Shashank Sharma and others)
- color manager (i.e. de-gamma, color conversion matrix & gamma support) from
Lionel Landwerlin
- Vulkan hsw support in the command parser (Jordan Justen)
- large-scale renaming of intel_engine_cs variables/parameters to avoid the epic
ring vs. engine confusion introduced in gen8 (Tvrtko Ursulin)
- few atomic patches from Maarten&Matt, big one is two-stage wm programming on ilk-bdw
- refactor driver load and add infrastructure to inject load failures for
testing, from Imre
- various small things all over
* tag 'drm-intel-next-2016-03-30' of git://anongit.freedesktop.org/drm-intel: (179 commits)
drm/i915: Update DRIVER_DATE to 20160330
drm/i915: Call intel_dp_mst_resume() before resuming displays
drm/i915: Fix races on fbdev
drm/i915: remove unused dev_priv->render_reclock_avail
drm/i915: move sdvo mappings to vbt data
drm/i915: move edp low vswing config to vbt data
drm/i915: use a substruct in vbt data for edp
drm/i915: replace for_each_engine()
drm/i915: introduce for_each_engine_id()
drm/i915/bxt: Fix DSI HW state readout
drm/i915: Remove vblank wait from hsw_enable_ips, v2.
drm/i915: Tidy aliasing_gtt_bind_vma()
drm/i915: Split PNV version of crtc_compute_clock()
drm/i915: Split g4x_crtc_compute_clock()
drm/i915: Split i8xx_crtc_compute_clock()
drm/i915: Split CHV and VLV specific crtc_compute_clock() hooks
drm/i915: Merge ironlake_compute_clocks() and ironlake_crtc_compute_clock()
drm/i915: Move fp divisor calculation into ironlake_compute_dpll()
drm/i915: Pass crtc_state->dpll directly to ->find_dpll()
drm/i915: Simplify ironlake_crtc_compute_clock() CPU eDP case
...
Currently we set the initial GPU frequency to min_freq_softlimit
on gen9, and to efficient_freq on VLV/CHV. On all the other platforms
we set it to idle_freq. Let's use idle_freq across the board to make
sure we don't waste power. This is especially relevant for VLV since
Vnn won't drop to minimum unless the GPU is at the minimum frequency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
After a suspend-resume cycle, the resumed kernel has no idea what the
booted kernel may have done to the GuC before replacing itself with the
resumed image. In particular, it may have already loaded the GuC with
firmware, which will then cause this kernel's attempt to (re)load the
firmware to fail (GuC program memory is write-once!). The symptoms
(GuC firmware reload fails after hibernation) are further described
in the Bugzilla reference below.
So let's *always* reset the GuC just before (re)loading the firmware;
the hardware should then be in a well-known state, and we may even
avoid some of the issues arising from unpredictable timing.
Also added some more fields & values to the definition of the GUC_STATUS
register, which is the key diagnostic indicator if the GuC load fails.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Both the oom and vmap notifier callbacks have a loop to acquire the
struct_mutex and set the device as uninterruptible, within a certain
time. Refactor the common code into a pair of functions.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459848145-24042-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If the core runs out of vmap address space, it will call a notifier in
case any driver can reap some of its vmaps. As i915.ko is possibily
holding onto vmap address space that could be recovered, hook into the
notifier chain and try and reap objects holding onto vmaps.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Roman Pen <r.peniaev@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-4-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since we only attempt to purge an object if can_release_pages() report
true, we should also only add it to the count of potential recoverable
pages when can_release_pages() is true.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
It may caused a dead lock if we flush the hpd work in bridge disable time.
The normal flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
3. HPD work already in idle, no need to run the work function.
OUT <-- analogix_dp_bridge
OUT <-- DRM IOCTL
The dead lock flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
IN --> analogix_dp_hotplug
IN --> drm_helper_hpd_irq_event
3. Acquire mode_config lock (This lock already have been acquired in previous step 1)
** Dead Lock Now **
It's wrong to flush the hpd work in bridge->disable time, I guess the
original code just want to ensure the delay work must be finish before
encoder disabled.
The flush work in bridge disable time is try to ensure the HPD event
won't be missed before display card disabled, actually we can take a
fast respond way(interrupt thread) to update DRM HPD event to fix the
delay update and possible dead lock.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Turn off the panel power in suspend time would help to reduce
power waste.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Display Port monitor could support kinds of mode which indicate
in monitor edid, not just one single display resolution which
defined in panel or devivetree property display timing.
Note: Gustavo Padovan try to remove the controller and phy
power on function in bind time at bellow commit:
drm/exynos: do not start enabling DP at bind() phase
But for now driver need to read edid message in .get_modes()
function, so controller must be inited in bind time, so we
need to add controller init back.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
This change just make a little clean to make code more like
drm core expect, move hdp detect code from bridge->enable(),
and place them into connector->detect().
Note: Gustavo Padovan try to remove the controller and phy
power on function in bind time at bellow commit:
drm/exynos: do not start enabling DP at bind() phase
But for now the connector status don't hardcode to connected,
need to operate dp phy in .detect function, so we need to revert
parts if Gustavo Padovan's changes, add phy poweron
function in bind time.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Some edp screen do not have hpd signal, so we can't just return
failed when hpd plug in detect failed.
This is an hardware property, so we need add a devicetree property
"analogix,need-force-hpd" to indicate this sutiation.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
There are some IP limit on rk3288 that only support 4 physical lanes
of 2.7/1.6 Gbps/lane, so seprate them out by device_type flag.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
RK3288 need some special registers setting, we can separate
them out by the dev_type of plat_data.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Rockchip have three clocks for dp controller, we leave pclk_edp
to analogix_dp driver control, and keep the sclk_edp_24m and
sclk_edp in platform driver.
Acked-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Both hsync/vsync polarity and interlace mode can be parsed from
drm display mode, and dynamic_range and ycbcr_coeff can be judge
by the video code.
But presumably Exynos still relies on the DT properties, so take
good use of mode_fixup() in to achieve the compatibility hacks.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
link_rate and lane_count already configured in analogix_dp_set_link_train(),
so we don't need to config those repeatly after training finished, just
remove them out.
Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets
would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Fix some obvious alignment problems, like alignment and line
over 80 characters problems, make this easy to be maintained
later.
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
In the original split we kept the register constants intact to keep the
diff small. Still the constants are Analogix-specific, so rename them now.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
The core functionality now resides in the generic bridge part so the
exynos-specific implementation details can get a more suitable nameing.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These should be set by default otherwise the UVD/VCE performance
won't be optimal.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
and revert fix following it accordingly
Revert "drm/amdgpu: stop trying to suspend UVD sessions v2"
Revert "drm/amdgpu: fix the UVD suspend sequence order"
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In commit e45708976a ("drm/dp-helper: Move the legacy helpers to
gma500") the legacy i2c helpers were moved to the only remaining user of
them, the gma500 driver. Together with that move, i2c_dp_aux_add_bus()
was marked deprecated and started warning about its remaining use.
It's now been a year and a half of annoying warning, and apparently
nobody cares enough about gma500 to try to move it along to the more
modern models.
Get rid of the warning - if even the gma500 people don't care enough,
then they should certainly not spam other innocent developers with a
warning that might hide other, much more real issues.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge PAGE_CACHE_SIZE removal patches from Kirill Shutemov:
"PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
Let's stop pretending that pages in page cache are special. They are
not.
The first patch with most changes has been done with coccinelle. The
second is manual fixups on top.
The third patch removes macros definition"
[ I was planning to apply this just before rc2, but then I spaced out,
so here it is right _after_ rc2 instead.
As Kirill suggested as a possibility, I could have decided to only
merge the first two patches, and leave the old interfaces for
compatibility, but I'd rather get it all done and any out-of-tree
modules and patches can trivially do the converstion while still also
working with older kernels, so there is little reason to try to
maintain the redundant legacy model. - Linus ]
* PAGE_CACHE_SIZE-removal:
mm: drop PAGE_CACHE_* and page_cache_{get,release} definition
mm, fs: remove remaining PAGE_CACHE_* and page_cache_{get,release} usage
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Doing a lot of work in the interrupt handler introduces huge
latencies to the system as a whole.
Most dramatic effect can be seen by running an all engine
stress test like igt/gem_exec_nop/all where, when the kernel
config is lean enough, the whole system can be brought into
multi-second periods of complete non-interactivty. That can
look for example like this:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/u8:3:143]
Modules linked in: [redacted for brevity]
CPU: 0 PID: 143 Comm: kworker/u8:3 Tainted: G U L 4.5.0-160321+ #183
Hardware name: Intel Corporation Broadwell Client platform/WhiteTip Mountain 1
Workqueue: i915 gen6_pm_rps_work [i915]
task: ffff8800aae88000 ti: ffff8800aae90000 task.ti: ffff8800aae90000
RIP: 0010:[<ffffffff8104a3c2>] [<ffffffff8104a3c2>] __do_softirq+0x72/0x1d0
RSP: 0000:ffff88014f403f38 EFLAGS: 00000206
RAX: ffff8800aae94000 RBX: 0000000000000000 RCX: 00000000000006e0
RDX: 0000000000000020 RSI: 0000000004208060 RDI: 0000000000215d80
RBP: ffff88014f403f80 R08: 0000000b1b42c180 R09: 0000000000000022
R10: 0000000000000004 R11: 00000000ffffffff R12: 000000000000a030
R13: 0000000000000082 R14: ffff8800aa4d0080 R15: 0000000000000082
FS: 0000000000000000(0000) GS:ffff88014f400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa53b90c000 CR3: 0000000001a0a000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
042080601b33869f ffff8800aae94000 00000000fffc2678 ffff88010000000a
0000000000000000 000000000000a030 0000000000005302 ffff8800aa4d0080
0000000000000206 ffff88014f403f90 ffffffff8104a716 ffff88014f403fa8
Call Trace:
<IRQ>
[<ffffffff8104a716>] irq_exit+0x86/0x90
[<ffffffff81031e7d>] smp_apic_timer_interrupt+0x3d/0x50
[<ffffffff814f3eac>] apic_timer_interrupt+0x7c/0x90
<EOI>
[<ffffffffa01c5b40>] ? gen8_write64+0x1a0/0x1a0 [i915]
[<ffffffff814f2b39>] ? _raw_spin_unlock_irqrestore+0x9/0x20
[<ffffffffa01c5c44>] gen8_write32+0x104/0x1a0 [i915]
[<ffffffff8132c6a2>] ? n_tty_receive_buf_common+0x372/0xae0
[<ffffffffa017cc9e>] gen6_set_rps_thresholds+0x1be/0x330 [i915]
[<ffffffffa017eaf0>] gen6_set_rps+0x70/0x200 [i915]
[<ffffffffa0185375>] intel_set_rps+0x25/0x30 [i915]
[<ffffffffa01768fd>] gen6_pm_rps_work+0x10d/0x2e0 [i915]
[<ffffffff81063852>] ? finish_task_switch+0x72/0x1c0
[<ffffffff8105ab29>] process_one_work+0x139/0x350
[<ffffffff8105b186>] worker_thread+0x126/0x490
[<ffffffff8105b060>] ? rescuer_thread+0x320/0x320
[<ffffffff8105fa64>] kthread+0xc4/0xe0
[<ffffffff8105f9a0>] ? kthread_create_on_node+0x170/0x170
[<ffffffff814f351f>] ret_from_fork+0x3f/0x70
[<ffffffff8105f9a0>] ? kthread_create_on_node+0x170/0x170
I could not explain, or find a code path, which would explain
a +20 second lockup, but from some instrumentation it was
apparent the interrupts off proportion of time was between
10-25% under heavy load which is quite bad.
When a interrupt "cliff" is reached, which was >~320k irq/s on
my machine, the whole system goes into a terrible state of the
above described multi-second lockups.
By moving the GT interrupt handling to a tasklet in a most
simple way, the problem above disappears completely.
Testing the effect on sytem-wide latencies using
igt/gem_syslatency shows the following before this patch:
gem_syslatency: cycles=1532739, latency mean=416531.829us max=2499237us
gem_syslatency: cycles=1839434, latency mean=1458099.157us max=4998944us
gem_syslatency: cycles=1432570, latency mean=2688.451us max=1201185us
gem_syslatency: cycles=1533543, latency mean=416520.499us max=2498886us
This shows that the unrelated process is experiencing huge
delays in its wake-up latency. After the patch the results
look like this:
gem_syslatency: cycles=808907, latency mean=53.133us max=1640us
gem_syslatency: cycles=862154, latency mean=62.778us max=2117us
gem_syslatency: cycles=856039, latency mean=58.079us max=2123us
gem_syslatency: cycles=841683, latency mean=56.914us max=1667us
Showing a huge improvement in the unrelated process wake-up
latency. It also shows an approximate halving in the number
of total empty batches submitted during the test. This may
not be worrying since the test puts the driver under
a very unrealistic load with ncpu threads doing empty batch
submission to all GPU engines each.
Another benefit compared to the hard-irq handling is that now
work on all engines can be dispatched in parallel since we can
have up to number of CPUs active tasklets. (While previously
a single hard-irq would serially dispatch on one engine after
another.)
More interesting scenario with regards to throughput is
"gem_latency -n 100" which shows 25% better throughput and
CPU usage, and 14% better dispatch latencies.
I did not find any gains or regressions with Synmark2 or
GLbench under light testing. More benchmarking is certainly
required.
v2:
* execlists_lock should be taken as spin_lock_bh when
queuing work from userspace now. (Chris Wilson)
* uncore.lock must be taken with spin_lock_irq when
submitting requests since that now runs from either
softirq or process context.
v3:
* Expanded commit message with more testing data;
* converted missed locking sites to _bh;
* added execlist_lock comment. (Chris Wilson)
v4:
* Mention dispatch parallelism in commit. (Chris Wilson)
* Do not hold uncore.lock over MMIO reads since the block
is already serialised per-engine via the tasklet itself.
(Chris Wilson)
* intel_lrc_irq_handler should be static. (Chris Wilson)
* Cancel/sync the tasklet on GPU reset. (Chris Wilson)
* Document and WARN that tasklet cannot be active/pending
on engine cleanup. (Chris Wilson/Imre Deak)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Testcase: igt/gem_exec_nop/all
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94350
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1459768316-6670-1-git-send-email-tvrtko.ursulin@linux.intel.com
We accidentally return PTR_ERR(NULL) which is success instead of a
negative error code.
Fixes: 879e40bea6f2 ('drm: ARM HDLCD - get rid of devm_clk_put()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Clock is acquired with devm_clk_get() which already manages
corresponding resource.
I.e. in case of driver removal or failure on installaiton
clock resources will be automatically released and explicit
call of devm_clk_put() is not required.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Deal with errors from drm_universal_plane_init() in primary and cursor
plane init paths (sprites were already covered). Also make the code
neater by using goto for error handling.
v2: Rebased due to drm_universal_plane_init() 'name' parameter
v3: Another rebase due to s/""/NULL/
v4: Rebased on drm-nightly (Matthew Auld)
v5: Fix email address (Matthew Auld)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571402-32749-1-git-send-email-matthew.auld@intel.com
Supposedly the power sequencer still locks out the DPLL registers on
CHV, so let's issue a warning if it's still locked when enabling the
DPLL.
Also drop the redundant IS_MOBILE() check for VLV when we check the same
thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
DPLL_MD(PIPE_C) is AWOL on CHV. Instead of fixing it someone added
chicken bits to propagate the pixel multiplier from DPLL_MD(PIPE_B)
to either pipe B or C. So do that to make pixel repeat work on pipes
B and C. Pipe A is fine without any tricks.
Fortunately the pixel repeat propagation appears to be a oneshot
operation, so once the value has been written we can clear the
chicken bits. So it is still possible to drive pipe B and C with
different pixel multipliers simultaneosly.
Looks like DPLL_VGA_MODE_DIS must also be set in DPLL(PIPE_B)
for this to work. But since we keep that bit always set in all
DPLLs there's no problem.
This of course means we can't reliably read out the pixel multiplier
for pipes B and C. That would make the state checker unhappy, so I
added shadow copies of those registers in to dev_priv. The other
option would have been to skip pixel multiplier, dpll_md an dotclock
checks entirely on CHV, but that feels like a serious loss of cross
checking, so just pretending that we have working DPLL MD registers
seemed better. Obviously with the shadow copies we can't detect if
the pixel multiplier was properly configured, nor can we take over
its state from the BIOS, but hopefully people won't have displays
that would be limitd to such crappy modes.
There is one strange flicker still remaining. It's visible on
pipe C/HDMID when HDMIB is enabled while driven by pipe B.
It doesn't occur if pipe A drives HDMIB, nor is there any glitch
on pipe B/HDMIB when port C/HDMID starts up. I don't have a board
with HDMIC so not sure if it happens there too. So I'm not sure
if it's somehow tied in with this strange linkage between pipe B
and C. Sadly I was unable to find an enable sequence that would
avoid the glitch, but at least it's not fatal ie. the output
recovers afterwards.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The VLV and CHV DPLL disable and update are almost identical in
how the DPLL/DPLL_MD registers need to be set up. But the code
looks more different than it really is. Try to bring them into
line.
Note that we now leave the refclock always enabled for both
DPLLs in the dual channel PHY. But that's perfectly fine since
it's the same clock, and we anyway already do that when turning
the disp2d power well on.
v2: s/chv_update_pll/chv_compute_dpll/
v3: Add a note that we leave refclocks enabled for both DPLLs (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Bspec is confused w.r.t. the HSW/BDW FDI disable sequence. It lists
FDI RX disable both as step 13 and step 18 in the sequence. But I dug
up an old BUN mail from Art that moved the FDI RX disable to happen
before DDI_BUF_CTL disable. That BUN did not renumber the steps and just
added a note:
"Workaround: Disable PCH FDI Receiver before disabling DDI_BUF_CTL."
The BUN described the symptoms of the fixed issue as:
"PCH display underflow and a black screen on the analog CRT port that
happened after a FDI re-train"
I suppose later someone tried to renumber the steps to match, but forgot
to remove the FDI RX disable from its old position in the sequence.
They also forgot to update the note describing what should be done in
case of an FDI training failure. Currently it says:
"To retry FDI training, follow the Disable Sequence steps to Disable FDI,
but skip the steps related to clocks and PLLs (16, 19, and 20), ..."
It should really say "17, 20, and 21" with the current sequence because
those are the steps that deal with PLLs and whatnot, after step 13 became
FDI RX disable. And had the step 18 FDI RX disable been removed, as I
suspect it should have, the note should actually say "17, 19, and 20".
So, let's move the FDI RX disable to happen before DDI_BUF_CTL disable,
as that would appear to be the correct order based on the BUN.
Note that Art has since unconfused the spec, and so this patch should
now match the steps listed in the spec.
v2: Add a note that the spec is now correct
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1456841783-4779-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Prevents the
if (WARN_ON(pipe >= dev->num_crtcs))
in drm_vblank_on/off from triggering if acceleration fails to
initialize, in which case we call drm_vblank_cleanup.
Reported-and-Tested-by: Julian Margetson <runaway@candw.ms>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
since the rcu slot was initialized to be num_hw_submission,
if command submission doesn't use scheduler, this limitation
will be invalid like uvd test.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes a memory leak when we can't register the callback on a fence.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We have the info, so use it rather than reporting just DDR.
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The offset changed on Fiji.
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
early_init gets called before atom asic init so on non-posted
cards, the vram type is not initialized.
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Without this, since the conversion from drm_vblank_pre/post_modeset to
drm_vblank_on/off, the vblank interrupt could never be disabled after
userspace triggered enabling it.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without this, since the conversion from drm_vblank_pre/post_modeset to
drm_vblank_on/off, the vblank interrupt could never be disabled after
userspace triggered enabling it.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes slow performance on resume.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add comparison function used by powerplay to determine which
power state to select.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure powerplay initialized properly before enabling
debugfs pm files.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed- by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't support the dpm parameter in powerplay.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit a7442b93cf.
With the patch applied SNB, IVB and ILK are experiencing hard machine
hangs. Original patch was to fix "just" kernel panics so it's not a good
trade-off.
Proper fix for the panic is on the way, lets revert until then.
Fixes: a7442b93cf ("drm/i915: Fix races on fbdev")
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459510861-29035-1-git-send-email-joonas.lahtinen@linux.intel.com
According to the BSpec update, bit 7 of PORT_CL1CM_DW0 register needs to be
checked to ensure that the register is in accessible state.
Also, based on a BSpec update, changing the timeout value to
check iphypwrgood, from 10ms to wait for up to 100us.
v2: [Ville] use wait_for_us instead of the atomic call.
v3: [Jani/Imre] read register only once
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reported-by: Philippe Lecluse <Philippe.Lecluse@intel.com>
Cc: Deak, Imre <imre.deak@intel.com>
Cc: Nikula, Jani <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459446354-19012-1-git-send-email-vandana.kannan@intel.com
This patch checks for changes in sink count between short pulse
hpds and forces full detect when there is a change.
This will allow both detection of hotplug and unplug of panels
through dongles that give only short pulse for such events.
v2: changed variable type from u8 to bool (Jani)
return immediately if perform_full_detect is set(Siva)
v3: changed method of determining full detection from using
pointer to return code (Siva)
v4: changed comments to indicate meaning of return value of
intel_dp_short_pulse and explain the use of return value
from intel_dp_get_dpcd in intel_dp_short_pulse (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-5-git-send-email-shubhangi.shrivastava@intel.com
Sink count can change between short pulse hpd hence this patch
adds a member variable to intel_dp so we can track any changes
between short pulse interrupts.
This patch reads sink_count dpcd always and removes its
read operation based on values in downstream port dpcd.
SINK_COUNT dpcd is not dependent on DOWNSTREAM_PORT_PRESENT dpcd.
SINK_COUNT denotes if a display is attached, while
DOWNSTREAM_PORT_PRESET indicates how many ports are available
in the dongle where display can be attached. so it is possible
for sink count to change irrespective of value in downstream
port dpcd.
Here is a table of possible values and scenarios
sink_count downstream_port
present
0 0 no display is attached
0 1 dongle is connected without display
1 0 display connected directly
1 1 display connected through dongle
v2: Storing value of intel_dp->sink_count that is ready
for consumption. (Ander)
Squashing two commits into one. (Ander)
v3: Added comment to explain the need of early return when
sink count is 0. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-4-git-send-email-shubhangi.shrivastava@intel.com
When created originally intel_dp_check_link_status()
was supposed to handle only link training for short
pulse but has grown into handler for short pulse itself.
This patch cleans up this function by splitting it into
two halves. First intel_dp_short_pulse() is called,
which will be entry point and handle all logic for
short pulse handling while intel_dp_check_link_status()
will retain its original purpose of only doing link
status related work.
intel_dp_short_pulse: All existing code other than
link status read and link training upon error status.
intel_dp_check_link_status:
The link status should be read on short pulse
irrespective of panel being enabled or not so
intel_dp_get_link_status() performs dpcd read first
then based on crtc active / enabled it will
perform the link training.
This is because short pulse is a generic interrupt
which should always be handled, because it may mean:
1. Hotplug/unplug of MST panel
2. Hotplug/unplug of dongle
3. Link status change for other DP panels
v2: Added WARN_ON to intel_dp_check_link_status()
Removed a call to intel_dp_get_link_status() (Ander)
v3: Changed commit message to explain need of link status
being read before performing encoder checks (Daniel)
v4: Changed commit message to explain need of reading
link status on short pulse (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[anderco: fix parenthesis alignment]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-3-git-send-email-shubhangi.shrivastava@intel.com
Current DP detection has DPCD operations split across
intel_dp_hpd_pulse and intel_dp_detect which contains
duplicates as well. Also intel_dp_detect is called
during modes enumeration as well which will result
in multiple dpcd operations. So this patch tries
to solve both these by bringing all DPCD operations
in one single function and make intel_dp_detect
use existing values instead of repeating same steps.
v2: Pulled in a hunk from last patch of the series to
this patch. (Ander)
v3: Added MST hotplug handling. (Ander)
v4: Added a flag to check if detect is performed to
prevent multiple detects on hotplug. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[anderco: fix parenthesis aligment]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-2-git-send-email-shubhangi.shrivastava@intel.com
intel_dp_detect() is called for not just detection but
during modes enumeration as well. Repeating the whole
sequence during each of these calls is wasteful and
time consuming.
This patch moves probing for panel, DPCD read etc done in
intel_dp_detect() to a new function intel_dp_long_pulse().
Note that the behavior of intel_dp_detect() is changed to
report connected or disconnected depending on whether the
EDID is available or not.
This change will be required by further patches in the series
to avoid performing duplicated DPCD operations on hotplug.
v2: Moved a hunk to next patch of the series.
Moved intel_dp_unset_edid to out. (Ander)
v3: Rephrased commit message and intel_dp_unset_dp() is called
within intel_dp_set_dp() to free the previous EDID. (Ander)
v4: Added overriding of status to disconnected for MST. (Ander)
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[anderco: fix parenthesis alignment]
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459341326-13142-1-git-send-email-shubhangi.shrivastava@intel.com
For drm_gem_object_unreference callers are required to hold
dev->struct_mutex, which these paths don't. Enforcing this requirement
has become a bit more strict with
commit ef4c6270bf
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 09:36:25 2015 +0200
drm/gem: Check locking in drm_gem_object_unreference
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
1) don't let other threads trying to bang on aux channel interrupt the
defer timeout/logic
2) don't let other threads interrupt the i2c over aux logic
Technically, according to people who actually have the DP spec, this
should not be required. In practice, it makes some troublesome Dell
monitor (and perhaps others) work, so probably a case of "It's compliant
if it works with windows" on the hw vendor's part..
v2: rebased to come before DPCD/AUX logging patch for easier backport
to stable branches.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1274157
Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
two minor msm fixes.
* 'msm-fixes-4.6-rc1' of git://people.freedesktop.org/~robclark/linux:
drm/msm: fix typo in the !COMMON_CLK case
drm/msm: fix bug after preclose removal
Just a few fixes for 4.6 this week:
- Add some SI DPM quirks
- Improve the ACP Kconfig text
- Additional BO pinning checks
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Don't move pinned BOs
drm/radeon: Don't move pinned BOs
drm/radeon: add a dpm quirk for all R7 370 parts
drm/radeon: add another R7 370 quirk
drm/radeon: add a dpm quirk for sapphire Dual-X R7 370 2G D5
drm/amd: Beef up ACP Kconfig menu text
Right now exynos is exposing DPI as a TMDS encoder and VGA connector,
which seems rather misleading. This isn't just an internal detail,
since xrandr actually exposes "VGA" as the output name. Define some
new enums so that vc4's DPI can have a more informative name.
I considered other names for the connector as well. For VC4, the
Adafruit DPI kippah takes the 28 GPIO pins and routes them to a
standard-ish 40-pin FPC connector, but "40-pin FPC" doesn't uniquely
identify an ordering of pins (apparently some other orderings exist),
doesn't explain things as well for the user (who, if anything, knows
their product is a DPI kippah/panel combo), and actually doesn't have
to exist (one could connect the 28 GPIOs directly to something else).
Simply "DPI" seems like a good compromise name to distinguish from the
HDMI, DSI, and TV connectors .
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refer to the GGTT VM consistently as "ggtt->base" instead of just "ggtt",
"vm" or indirectly through other variables like "dev_priv->ggtt.base"
to avoid confusion with the i915_ggtt object itself and PPGTT VMs.
Refer to the GGTT as "ggtt" instead of indirectly through chaining.
As a bonus gets rid of the long-standing i915_obj_to_ggtt vs.
i915_gem_obj_to_ggtt conflict, due to removal of i915_obj_to_ggtt!
v2:
- Added some more after grepping sources with Chris
v3:
- Refer to GGTT VM through ggtt->base consistently instead of ggtt_vm
(Chris)
v4:
- Convert all dev_priv->ggtt->foo accesses to ggtt->foo.
v5:
- Make patch checker happy
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Without this a vblank may occur between updating color management
and planes, which should be prevented.
intel_color_set_csc was called in update pipe config because the
handover from hardware may not have any csc set, which resulted
in a black screen. Because of this also update color management
during fastset.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459350996-4957-4-git-send-email-maarten.lankhorst@linux.intel.com
[mlankhorst: Remove comment in response to review feedback.]
imx doesn't have any functions for setting the gamma table, so this is
completely defunct.
Not nice to lie to userspace, so let's stop!
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Just as the function ipu_dmfc_config_wait4eot() tells, the DMFC wait4eot bit
depends on the number of DMFC slots to be used, so it should be called after
the slots are determined in the function ipu_dmfc_alloc_bandwidth().
Based on tests, this patch may eliminate display distortion issue on overlay
plane with small resolutions. To reproduce the issue, we may run this drm
modetest case - 'modetest -P 19:64x64'.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The function name 'ipu_dmfc_config_wait4eot' matches the implementation of
the function better than 'ipu_dmfc_init_channel', since it only touches the
wait4eot bits.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Since the function ipu_dmfc_init_channel() always returns zero, we may
change the return type to void to simplify the code.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
To avoid race condition issue, we should protect the function
ipu_dmfc_init_channel() with the mutex dmfc->priv->mutex, since it
configures the register DMFC_GENERAL1 at runtime which contains
several control bits for various display channels. This matches
better with fine grained locking logic in upper layer.
Signed-off-by: Liu Ying <gnuiyl@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The IMX dw_hdmi driver just called platform_set_drvdata() to get
your hopes up that maybe, somehow, you'd be able to retrieve the 'struct
imx_hdmi' from a pointer to the 'struct device'. You can't. When
we call dw_hdmi_bind() the main driver calls dev_set_drvdata(), which
clobbers our setting.
Let's just remove the platform_set_drvdata() to avoid dashing people's
hopes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The drm_encoder_cleanup() was missing both from the error path of
dw_hdmi_imx_bind(). This caused a crash when slub_debug was
enabled and we ended up deferring probe of HDMI at boot.
This call isn't needed from unbind() because if dw_hdmi_bind() returns
no error then it takes over the job of freeing the encoder (in
dw_hdmi_unbind).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The driver already advertises multi-planar YUV support, but
previously the U/V offset and stride setup was missing.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The IPU addresses multiplanar formats using a base address and relative
offsets for the secondary planes. Since those offsets must be positive
and not too large, and none of the plane parameters except the base address
may be changed while scanout is active, store the pitches and u/v offsets
and check all values against IDMAC limitations.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Let ipu_cpmem_set_yuv_planar_full take a DRM_FORMAT instead of a
V4L2_PIXFMT and allow better control over U/V stride, U offset and
V offset settings in the CPMEM.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
With async modesets this is no longer protected with connection_mutex,
so ensure that each pll has its own lock. The pll configuration state
is still protected; it's only the pll updates that need locking against
concurrency.
Changes since v1:
- Rebased.
- Fix locking to protect all accesses. (Durgadoss)
Changes since v2:
- Make the dpll_lock global to protect concurrent updates to the
same register, for example DPLL_CTRL1 on skl. (Ander)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56F29F50.1090708@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
And move the comment to the right macro. This was mixed up in
commit cfb23ed622
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Tue Jul 14 12:17:40 2015 +0200
drm/i915: Allow fuzzy matching in pipe_config_compare, v2
v2: Rebase.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Stone <daniels@collabora.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459330476-32453-1-git-send-email-daniel.vetter@ffwll.ch
This allows us to ditch a ton of ugly #ifdefs from a bunch of drm modeset
drivers.
v2: Make the dummy function actually return a sane value, spotted by
Ville.
v3: Because the patch is still in limbo there's no more drivers to
convert, noticed by Emil.
v4: Rebase once more, because hooray. I'll just go ahead an apply this
one later on to drm-misc.
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This goes all the way back to the original KMS commit aeons ago
commit f453ba0460
Author: Dave Airlie <airlied@redhat.com>
Date: Fri Nov 7 14:05:41 2008 -0800
DRM: add mode setting support
But it seems to be completely unused. Only i915 and nouveau even
register these properties, and the corresponding DDX don't even look
at them. Also the sysfs files are read-only, so not useful to
configure anything.
I suspect that this was added with the goal to have read-only access
to all properties in sysfs, but we never followed through on that.
Also, that should be done in a more generic fashion.
Since it would be real work to fix up the locking (with atomic we're
now chasing pointers when reading properties) and it seems unused lets
just nuke this all. It's easier. Of course we'll keep the properties
themselves, those are still exposed through the KMS ioctls.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331120-27864-5-git-send-email-daniel.vetter@ffwll.ch
It tries to do fancy things with excluding agp support if ttm is
built-in, but agp isn't. Instead just express this depency like drm
does and use CONFIG_AGP everywhere.
Also use the neat Makefile magic to make the entire ttm_agp_backend
file optional.
v2: Use IS_ENABLED(CONFIG_AGP) as suggested by Ville
v3: Review from Emil.
v4: Actually get it right as spotted by 0-day.
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1459337046-25882-1-git-send-email-daniel.vetter@ffwll.ch
This effectively reverts
commit 8e5fd599eb
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Apr 9 13:28:50 2014 +0300
drm/i915/chv: Make CHV irq handler loop until all interrupts are consumed
as under continuous execlists load we can saturate the IRQ handler,
destablising the tsc clock and triggering the NMI watchdog to declare a hung
CPU.
[ 552.756051] clocksource: timekeeping watchdog on CPU0: Marking clocksource 'tsc' as unstable because the skew is too large:
[ 552.756080] clocksource: 'refined-jiffies' wd_now: 10003b480 wd_last: 10003b28c mask: ffffffff
[ 552.756091] clocksource: 'tsc' cs_now: d55d31aa50 cs_last: d17446166c mask: ffffffffffffffff
[ 552.756210] clocksource: Switched to clocksource refined-jiffies
[ 575.217870] NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
[ 575.217893] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.5.0-rc7+ #18
[ 575.217905] Hardware name: /NUC5CPYB, BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[ 575.217915] 0000000000000000 ffff88027fd05bc0 ffffffff81288c6d 0000000000000000
[ 575.217935] 0000000000000001 ffff88027fd05be0 ffffffff810e72d1 0000000000000000
[ 575.217951] ffff88027fd05c80 ffff88027fd05c20 ffffffff81114b60 0000000181015f1e
[ 575.217967] Call Trace:
[ 575.217973] <NMI> [<ffffffff81288c6d>] dump_stack+0x4f/0x72
[ 575.217994] [<ffffffff810e72d1>] watchdog_overflow_callback+0x151/0x160
[ 575.218003] [<ffffffff81114b60>] __perf_event_overflow+0xa0/0x1e0
[ 575.218016] [<ffffffff811154c4>] perf_event_overflow+0x14/0x20
[ 575.218028] [<ffffffff8101d2ca>] intel_pmu_handle_irq+0x1da/0x460
[ 575.218042] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218052] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218064] [<ffffffff81014ae8>] perf_event_nmi_handler+0x28/0x50
[ 575.218075] [<ffffffff81007540>] nmi_handle+0x60/0x130
[ 575.218086] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218096] [<ffffffff810079c0>] do_nmi+0x140/0x470
[ 575.218108] [<ffffffff81559ec7>] end_repeat_nmi+0x1a/0x1e
[ 575.218119] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218129] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218139] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218148] <<EOE>> [<ffffffff814a8353>] cpuidle_enter_state+0xf3/0x2f0
[ 575.218164] [<ffffffff814a8587>] cpuidle_enter+0x17/0x20
[ 575.218175] [<ffffffff810aaa3a>] call_cpuidle+0x2a/0x40
[ 575.218185] [<ffffffff810aade3>] cpu_startup_entry+0x273/0x330
[ 575.218196] [<ffffffff81033a1e>] start_secondary+0x10e/0x130
However, not servicing all available IIR within the handler does hurt the
throughput of pathological nop execbuf by about 20%, with a similar effect
upon the dispatch latency of a series of execbuf.
v2: use do {} while(0) for a smaller patch, and easier to revert again
I have reasonable confidence that we do not miss GT interrupts (as
execlists provides a stress case with a failure mechanism easily
detected by igt), however I have less confidence about all the other
sources of interrupts and worry that may lose a display hotplug
interrupt, for example.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93467
Testcase: igt/gem_exec_nop/basic # requires NMI watchdog
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Antti Koskipää <antti.koskipaa@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457946117-6714-1-git-send-email-chris@chris-wilson.co.uk
__force_wake_get() only acquires a temporary wakeref on forcewake that is
automatically released when a timer expires. When reading the code
again, I confused __intel_uncore_forcewake_get() for __force_wake_get()
and to my shame thought I found a bug in unbalanced wake_count handling.
I claim that if the function had been called __force_wake_auto() instead
I would not have embarrassed myself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458829907-26596-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Rename and document the GGTT init functions to give a better
idea of the context where they are called from.
i915_gem_gtt_init => i915_ggtt_init_hw
i915_gem_init_global_gtt => i915_gem_init_ggtt
i915_global_gtt_cleanup => i915_ggtt_cleanup_hw
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458830866-12578-1-git-send-email-joonas.lahtinen@linux.intel.com
Lets BUG_ON and don't bother with a WARN and returning an error, so we can
remove the need to pollute the code with error handling, after all it is
a programmer error to provide NULL view. Also while we're here remove
redundant NULL ggtt_view check.
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458834860-7898-1-git-send-email-matthew.auld@intel.com
This reverts commit e91abf80a0.
Since
commit 24e4a8c3e8
Author: John Stultz <john.stultz@linaro.org>
Date: Wed Jul 16 21:03:53 2014 +0000
ktime: Kill non-scalar ktime_t implementation for 2038
there is no longer a 32bit version that's unsigned, and we don't have
to jump through ridiculous hoops to make the calculations correct.
I didn't look whether there's more of this pattern in the kernel.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459249942-21589-1-git-send-email-daniel.vetter@ffwll.ch
Since we need MST devices ready before we try to resume displays,
calling this after intel_display_resume() can result in some issues with
various laptop docks where the monitor won't turn back on after
suspending the system.
This order was originally changed in
commit e7d6f7d708 ("drm/i915: resume MST after reading back hw state")
In order to fix some unclaimed register errors, however the actual cause
of those has since been fixed.
CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Resolve conflicts with locking changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->lastclose callback invokes intel_fbdev_restore_mode() and has
been witnessed to run before intel_fbdev_initial_config_async()
has finished.
We might likewise receive hotplug events before we've had a chance to
fully set up the fbdev.
Fix by waiting for the asynchronous thread to finish.
v2:
An async_synchronize_full() was also added to intel_fbdev_set_suspend()
in v1 which turned out to be entirely gratuitous. It caused a deadlock
on suspend (discovered by CI, thanks to Damien Lespiau and Tomi Sarvela
for CI support) and was unnecessary since a device is never suspended
until its ->probe callback (and all asynchronous tasks it scheduled)
have finished. See dpm_prepare(), which calls wait_for_device_probe(),
which calls async_synchronize_full().
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93580
Reported-by: Gustav Fägerlind <gustav.fagerlind@gmail.com>
Reported-by: "Li, Weinan Z" <weinan.z.li@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160309115147.67B2B6E0D3@gabe.freedesktop.org
Accidentally fell through the cracks in
commit 6c87e5c3ec
Author: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Date: Wed Mar 23 11:42:54 2016 +0300
drm: Rename drm_connector_unplug_all() to drm_connector_unregister_all()
despite that Boris acked that patch.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Current name is a bit misleading because what that helper function
really does it calls drm_connector_unregister() for all connectors.
This all has nothing to do with hotplugging so let's name things
properly.
And while at it remove potentially dangerous locking around
drm_connector_unregister() in rcar_du_remove() as mentioned
in kerneldoc for drm_connector_unregister_all().
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458722577-20283-2-git-send-email-abrodkin@synopsys.com
The purpose of pinning is to prevent a buffer from moving.
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The purpose of pinning is to prevent a buffer from moving.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Higher mclk values are not stable due to a bug somewhere.
Limit them for now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The Rockchip dw_hdmi driver just called platform_set_drvdata() to get
your hopes up that maybe, somehow, you'd be able to retrieve the 'struct
rockchip_hdmi' from a pointer to the 'struct device'. You can't. When
we call dw_hdmi_bind() the main driver calls dev_set_drvdata(), which
clobbers our setting.
Let's just remove the platform_set_drvdata() to avoid dashing people's
hopes.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
This fixes a few problems in the vop crtc cleanup (handling error
paths and cleanup upon exit):
* The vop_create_crtc() error path had an unsafe version of the
iterator used for iterating over all planes (though it was
destroying planes in the iterator so should have used the safe
version)
* vop_destroy_crtc() - wasn't calling vop_plane_destroy(), which made
slub_debug unhappy, at least if we ended up running this due to a
deferred probe.
* In vop_create_crtc() if we were missing the "port" device tree node
we would fail but not return an error (found by code inspection).
Fix these problems.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
The drm_encoder_cleanup() was missing both from the error path of
dw_hdmi_rockchip_bind(). This caused a crash when slub_debug was
enabled and we ended up deferring probe of HDMI at boot.
This call isn't needed from unbind() because if dw_hdmi_bind() returns
no error then it takes over the job of freeing the encoder (in
dw_hdmi_unbind).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
When a VOP is re-enabled, it will start scanning right away the
framebuffers that were configured from the last time, even if those have
been destroyed already.
To prevent the VOP from trying to access freed memory, disable all its
windows when the CRTC is being disabled, then each window will get a
valid framebuffer address before it's enabled again.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Link: http://lkml.kernel.org/g/CAAObsKAv+05ih5U+=4kic_NsjGMhfxYheHR8xXXmacZs+p5SHw@mail.gmail.com
When closing the DRM device while a vblank is pending, we access
file_priv after it has been free'd, which gives:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at __list_add+0x5c/0xe8
LR is at send_vblank_event+0x54/0x1f0
...
[<c02952e8>] (__list_add) from [<c031a7b4>] (send_vblank_event+0x54/0x1f0)
[<c031a760>] (send_vblank_event) from [<c031a9c0>] (drm_send_vblank_event+0x70/0x78)
[<c031a950>] (drm_send_vblank_event) from [<c031a9f8>] (drm_crtc_send_vblank_event+0x30/0x34)
[<c031a9c8>] (drm_crtc_send_vblank_event) from [<c0339ad8>] (vop_isr+0x224/0x28c)
[<c03398b4>] (vop_isr) from [<c0081780>] (handle_irq_event_percpu+0x12c/0x3e4)
This can be triggered somewhat reliably with:
modetest -M rockchip -v -s ...
Add a preclose hook to the driver so that we can discard any pending
vblank events when the device is closed.
Signed-off-by: John Keeping <john@metanate.com>
If the geometry of a crtc is changing in an atomic update then we must
validate the plane size against the new state of the crtc and not the
current size, otherwise if the crtc size is increasing the plane will be
cropped at the previous size and will not fill the screen.
Signed-off-by: John Keeping <john@metanate.com>
Pull drm fixes from Dave Airlie:
"Just a couple of dma-buf related fixes and some amdgpu fixes, along
with a regression fix for radeon off but default feature, but makes my
30" monitor happy again"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/mst: cleanup code indentation
drm/radeon/mst: fix regression in lane/link handling.
drm/amdgpu: add invalidate_page callback for userptrs
drm/amdgpu: Revert "remove the userptr rmn->lock"
drm/amdgpu: clean up path handling for powerplay
drm/amd/powerplay: fix memory leak of tdp_table
dma-buf/fence: fix fence_is_later v2
dma-buf: Update docs for SYNC ioctl
drm: remove excess description
dma-buf, drm, ion: Propagate error code from dma_buf_start_cpu_access()
drm/atmel-hlcdc: use helper to get crtc state
drm/atomic: use helper to get crtc state
The current "text" needs a user to use a crystal ball in order to find
out what this ACP thing is.
Use the text from
a8fe58cec3 ("drm/amd: add ACP driver support")
to make it a bit more understandable to the rest of the world.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Jammy Zhou <Jammy.Zhou@amd.com>
Cc: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Cc: Murali Krishna Vemuri <murali-krishna.vemuri@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
some amd fixes
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/mst: cleanup code indentation
drm/radeon/mst: fix regression in lane/link handling.
drm/amdgpu: add invalidate_page callback for userptrs
drm/amdgpu: Revert "remove the userptr rmn->lock"
drm/amdgpu: clean up path handling for powerplay
drm/amd/powerplay: fix memory leak of tdp_table
Having provided for_each_engine_id() for cases where the third (id)
argument is useful, we can now replace all the remaining instances with
a simpler version that takes only two parameters. In many cases, this
also allows the elimination of the local variable used in the iterator
(usually 'i').
v2:
s/dev_priv/(dev_priv__)/ in body of for_each_engine_masked() [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458757194-17783-2-git-send-email-david.s.gordon@intel.com
Equivalent to the existing for_each_engine() macro, this will replace
the latter wherever the third argument *is* actually wanted (in most
places, it is not used). The third argument is renamed to emphasise
that it is an engine id (type enum intel_engine_id). All the callers of
the macro that actually need the third argument are updated to use this
version, and the argument (generally 'i') is also updated to be 'id'.
Other callers (where the third argument is unused) are untouched for
now; they will be updated in the next patch.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently the machine hangs during booting while accessing the
BXT_MIPI_PORT_CTRL register during pipe HW state readout. After some
experimentation I found that the hang is caused by the DSI PLL being
disabled, or it being enabled but with an incorrect divider
configuration. Enabling the PLL got rid of the boot problem, so fix
this by checking the PLL enabled state/configuration before attempting
to read out the HW state.
The DSI_PLL_ENABLE register is in the always-on power well, while the
BXT_DSI_PLL_CTL is in power well 0. This isn't exactly matched by the
transcoder power domain, but what we really need is just a runtime PM
reference, which is provided by any power domain.
Ville also found this dependency specified in BSpec, so I added a
reference to that too.
v2:
- Make sure we hold a power reference while accessing the PLL registers.
v3: (Jani)
- Simplify check in bxt_get_dsi_transcoder_state()
- Add comment explaining why we check for valid dividers in
bxt_dsi_pll_is_enabled()
CC: Shashank Sharma <shashank.sharma@intel.com>
CC: Uma Shankar <uma.shankar@intel.com>
CC: Jani Nikula <jani.nikula@intel.com>
Fixes: c6c794a2fc ("drm/i915/bxt: Initialize MIPI DSI for BXT")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458816100-31269-1-git-send-email-imre.deak@intel.com
intel_post_plane_update did an extra vblank wait that's no longer needed when enabling ips.
Changes since v1:
- Add comment explaining why vblank wait is performed. (Paulo)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56F29B28.5070804@linux.intel.com
Bunch of small fixupes all over. Plus a dma-buf patch that Sumit asked me
to cherry-pick since that's the only one he had in his tree.
There's a sparse issue outstanding in the color mgr stuff, but Lionel is
still working on something that actually appeases sparse.
* tag 'topic/drm-misc-2016-03-22' of git://anongit.freedesktop.org/drm-intel:
dma-buf/fence: fix fence_is_later v2
dma-buf: Update docs for SYNC ioctl
drm: remove excess description
dma-buf, drm, ion: Propagate error code from dma_buf_start_cpu_access()
drm/atmel-hlcdc: use helper to get crtc state
drm/atomic: use helper to get crtc state
commit 53190c7194
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
AuthorDate: Mon Jan 25 22:16:49 2016 +0100
Commit: Daniel Vetter <daniel.vetter@ffwll.ch>
CommitDate: Mon Feb 8 09:55:50 2016 +0100
drm/msm: Nuke preclose hooks
Left around the unused (and null) preclose fxn ptr, and things
predictibly explode when you try to call that.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In commit 0a87871626
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Oct 15 14:23:01 2015 +0200
drm/i915: restore ggtt double-bind avoidance
we wrote the ggtt_bind_vma() observing a number of cleanups we could do
over the template of aliasing_gtt_bind_vma(). Now let's apply the
cleanups we made there back to the original. The essence is to avoid
redundant variables and assignements, and by doing so make the code
easier to read.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1448015238-24639-1-git-send-email-chris@chris-wilson.co.uk
Split a GEN2 specific version from i9xx_crtc_compute_clock(). With this
there is no need for i9xx_get_refclk() anymore, and the differences
between platforms become more obvious.
v2: Use i8xx as prefix instead of gen2. (Ville and Daniel)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458653723-17951-1-git-send-email-ander.conselvan.de.oliveira@intel.com
In order for VLV and CHV to use i9xx_crtc_compute_clocks(), a number
of if ladders is necessary: one for setting the find_dpll() hook, one
for choosing the limits struct, one for choosing the right compute dpll
function and one for initializing the crtc_compute_clock() hook.
By extracting a platform specific implementation for each platform, the
number of if-ladders is reduced to one.
While at it also clean up bxt_find_best_dpll() which depends on some of
the CHV code.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-13-git-send-email-ander.conselvan.de.oliveira@intel.com
Merge ironlake_compute_clocks() into ironlake_crtc_compute_clock() so
the clock computation logic is all in one place. The resulting function
is still quite simple. Follow up patches will make the similar code for
GMCH platforms look similar.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-12-git-send-email-ander.conselvan.de.oliveira@intel.com
When calculating clocks, just pass a pointer to crtc_state->dpll
directly to the find_dpll() hook. Back when this was introduced in
commit f47709a950 ("drm/i915: create pipe_config->dpll for clock
state") there was no staged crtc config or atomic crtc state, so it was
possible to overwrite the current configuration on error. That hasn't
been the case for a while now, so finally make it "disappear".
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-10-git-send-email-ander.conselvan.de.oliveira@intel.com
None of the code in ironlake_crtc_compute_clock() is relevant for CPU
eDP. The CPU eDP PLL is turned on and off in ironlake_edp_pll_{on,off}
from the DP code and that doesn't depend on the crtc_state->dpll values,
so just return early in that case.
v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-9-git-send-email-ander.conselvan.de.oliveira@intel.com
The checks were added in commit 5dc5298bb3 ("drm/i915: add proper
CPU/PCH checks to crtc_mode_set functions") in a time when there was
doubts on what PCHs would be supported by HSW. There are similar checks
for PCH type in intel_detect_pch() and the function pointers are
initialized based on platform/pch information, so the removed WARN can't
ever be reached.
v2: Rebase without patch that drops lvds downclock code. (Ville)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-8-git-send-email-ander.conselvan.de.oliveira@intel.com
Remove the clock calculation from ironlake_crtc_compute_clock() when the
encoder compute_config() already set one. The value was just thrown away
in that case.
Note that the previously set clock is not validated against the limits
anymore. That is ok since the fixed clocks from DP and SDVO are within
the supported range, so the call to ironlake_compute_clocks() would
never fail in that case.
v2: Add note about not checking fixed clocks agains limits. (Maarten)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-7-git-send-email-ander.conselvan.de.oliveira@intel.com
The function intel_ironlake_limit() is only called by the crtc compute
clock path. By merging it into ironlake_compute_clocks(), the code gets
clearer, since there's no more if-ladders to follow.
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458576016-30348-4-git-send-email-ander.conselvan.de.oliveira@intel.com
The wait for other gens was added in commit 564ed191f5 ("drm/i915:
gmch: fix stuck primary plane due to memory self-refresh mode") since
that's necessary when disabling cxsr. However, cxsr disabling was later
moved to intel_pre_disable_primary() in commit 87d4300a7d ("drm/i915:
Move intel_(pre_disable/post_enable)_primary to intel_display.c, and use
it there.") and that function got its own vblank wait for cxsr in commit
262cd2e154 ("drm/i915: CHV DDR DVFS support and another watermark
rewrite"). So remove the extra vblank wait from i9xx_crtc_distable().
Cc: Kalyan Kondapally <kalyan.kondapally@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458634284-6080-1-git-send-email-ander.conselvan.de.oliveira@intel.com
Commit d15d7538c6 ("drm/i915: Tune down init error message due
to failure injection") added i915_load_error message to failure
path on device initialization. The message is printed
after the device is freed. And as the message printing helper
uses the device structure, this leads to use after free.
Spotted by Kasan.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458721906-10625-1-git-send-email-mika.kuoppala@intel.com
amdkfd wants to know syscall type, not task type. Check directly.
Unfortunately, amdkfd is making nasty assumptions that a process'
bitness is a well-defined constant thing. This isn't the case on x86.
I don't know how much this matters, but this patch has no effect on
generated code on x86, so amdkfd is equally broken with and without this
patch.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Oded Gabbay <oded.gabbay@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This was all sorts of ugly from when I hacked it up,
just clean it up now and remove the extra indents.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function this used changed in
092c96a8ab
drm/radeon: fix dp link rate selection (v2)
However for MST we should just always train to the
max link/rate. Though we probably need to limit this
for future hw, in theory radeon won't support it.
This fixes my 30" monitor with MST enabled.
Cc: stable@vger.kernel.org # v4.4
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Joonas and Daniel remarked that our debugging output should stay compatible
with the core DRM's debug facility. The recently added __i915_printk() would
output debug messages even if debugging is completely disabled via the
drm.debug option. To fix this make __i915_printk behave the same as
DRM_DEBUG_DRIVER in this case.
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458572937-21712-1-git-send-email-imre.deak@intel.com
At the end of an atomic commit, we currently wait for vblanks to
complete, call put() on the various runtime PM references, and then try
to optimize our watermarks (on platforms that need two-step watermark
programming). This can lead to watermark registers being programmed
while the power well is powered down. We need to wait until after
watermark optimization is complete before dropping our runtime power
references.
Note that in the future the watermark optimization is probably going to
move to an asynchronous workqueue task that happens at some arbitrary
point after vblank. When we make that change, we'll no longer
necessarily be operating under the power reference held here, so we'll
need to wrap the watermark register programmin in a call to
intel_runtime_pm_get_if_in_use() or similar.
Cc: arun.siluvery@linux.intel.com
Cc: ville.syrjala@linux.intel.com
Cc: maarten.lankhorst@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94349
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457135979-23727-1-git-send-email-matthew.d.roper@intel.com
In preparation for engine reset, the wedged argument of i915_handle_error()
is extended to reflect as a mask of engines that are hung. This is further
passed down to error state capture functions which are also updated.
Engine reset recovery mechanism uses this mask and schedules recovery work
for those particular engines.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458331676-567-3-git-send-email-arun.siluvery@linux.intel.com
Initialize hangcheck struct during driver load. Since we do the same after
recovering from a reset, this is extracted into a helper function.
v2: remove redundant hangcheck init during load as this is done when
engines are initialized (Chris)
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458577619-12006-1-git-send-email-arun.siluvery@linux.intel.com
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.6 kernel.
Overall the coolest thing here for me is the nouveau maxwell signed
firmware support from NVidia, it's taken a long while to extract this
from them.
I also wish the ARM vendors just designed one set of display IP, ARM
display block proliferation is definitely increasing.
Core:
- drm_event cleanups
- Internal API cleanup making mode_fixup optional.
- Apple GMUX vga switcheroo support.
- DP AUX testing interface
Panel:
- Refactoring of DSI core for use over more transports.
New driver:
- ARM hdlcd driver
i915:
- FBC/PSR (framebuffer compression, panel self refresh) enabled by default.
- Ongoing atomic display support work
- Ongoing runtime PM work
- Pixel clock limit checks
- VBT DSI description support
- GEM fixes
- GuC firmware scheduler enhancements
amdkfd:
- Deferred probing fixes to avoid make file or link ordering.
amdgpu/radeon:
- ACP support for i2s audio support.
- Command Submission/GPU scheduler/GPUVM optimisations
- Initial GPU reset support for amdgpu
vmwgfx:
- Support for DX10 gen mipmaps
- Pageflipping and other fixes.
exynos:
- Exynos5420 SoC support for FIMD
- Exynos5422 SoC support for MIPI-DSI
nouveau:
- GM20x secure boot support - adds acceleration for Maxwell GPUs.
- GM200 support
- GM20B clock driver support
- Power sensors work
etnaviv:
- Correctness fixes for GPU cache flushing
- Better support for i.MX6 systems.
imx-drm:
- VBlank IRQ support
- Fence support
- OF endpoint support
msm:
- HDMI support for 8996 (snapdragon 820)
- Adreno 430 support
- Timestamp queries support
virtio-gpu:
- Fixes for Android support.
rockchip:
- Add support for Innosilicion HDMI
rcar-du:
- Support for 4 crtcs
- R8A7795 support
- RCar Gen 3 support
omapdrm:
- HDMI interlace output support
- dma-buf import support
- Refactoring to remove a lot of legacy code.
tilcdc:
- Rewrite of pageflipping code
- dma-buf support
- pinctrl support
vc4:
- HDMI modesetting bug fixes
- Significant 3D performance improvement.
fsl-dcu (FreeScale):
- Lots of fixes
tegra:
- Two small fixes
sti:
- Atomic support for planes
- Improved HDMI support"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1063 commits)
drm/amdgpu: release_pages requires linux/pagemap.h
drm/sti: restore mode_fixup callback
drm/amdgpu/gfx7: add MTYPE definition
drm/amdgpu: removing BO_VAs shouldn't be interruptible
drm/amd/powerplay: show uvd/vce power gate enablement for tonga.
drm/amd/powerplay: show uvd/vce power gate info for fiji
drm/amdgpu: use sched fence if possible
drm/amdgpu: move ib.fence to job.fence
drm/amdgpu: give a fence param to ib_free
drm/amdgpu: include the right version of gmc header files for iceland
drm/radeon: fix indentation.
drm/amd/powerplay: add uvd/vce dpm enabling flag to fix the performance issue for CZ
drm/amdgpu: switch back to 32bit hw fences v2
drm/amdgpu: remove amdgpu_fence_is_signaled
drm/amdgpu: drop the extra fence range check v2
drm/amdgpu: signal fences directly in amdgpu_fence_process
drm/amdgpu: cleanup amdgpu_fence_wait_empty v2
drm/amdgpu: keep all fences in an RCU protected array v2
drm/amdgpu: add number of hardware submissions to amdgpu_fence_driver_init_ring
drm/amdgpu: RCU protected amd_sched_fence_release
...
Patch based on a previous series by Shashank Sharma.
v2: Update contributors
v3: Refactor degamma/gamma LUTs load into a single function
v4: Remove unused variable
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-5-git-send-email-lionel.g.landwerlin@intel.com
Patch based on a previous series by Shashank Sharma.
v2: Do not read GAMMA_MODE register to figure what mode we're in
v3: Program PREC_PAL_GC_MAX to clamp pixel values > 1.0
Add documentation on how the Broadcast RGB property is affected by CTM
v4: Update contributors
v5: Refactor degamma/gamma LUTs load into a single function
v6: Fix missing intel_crtc variable (bisect issue)
v7: Fix & simplify limited range matrix multiplication (Matt Roper's
comment)
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Kumar, Kiran S <kiran.s.kumar@intel.com>
Signed-off-by: Kausal Malladi <kausalmalladi@gmail.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Acknowledged-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-4-git-send-email-lionel.g.landwerlin@intel.com
Implement Daniel Stone's recommendation to not read registers to infer
the hardware's state.
v2: Read GAMMA_MODE register value at init (Matt Roper's comment)
v3: Read GAMMA_MODE register in intel_modeset_readout_hw_state along
with other registers (Matt Roper's comment).
v4: Mask GAMMA_MODE register with interesting bits when reading
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125837-2576-3-git-send-email-lionel.g.landwerlin@intel.com
The moves a couple of functions programming the gamma LUT and CSC
units into their own file.
On generations prior to Haswell there is only a gamma LUT. From
haswell on there is also a new enhanced color correction unit that
isn't used yet. This is why we need to set the GAMMA_MODE register,
either we're using the legacy 8bits LUT or enhanced LUTs (of 10 or
12bits).
The CSC unit is only available from Haswell on.
We also need to make a special case for CherryView which is recognized
as a gen 8 but doesn't have the same enhanced color correction unit
from Haswell on.
v2: Fix access to GAMMA_MODE register on older generations than
Haswell (from Matt Roper's comments)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1458125837-2576-2-git-send-email-lionel.g.landwerlin@intel.com
Otherwise we can run into problems with the writeback code.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c02196834456f2d5fad334088b70e98ce4967c34.
In the meantime we moved get_user_pages() outside of the reservation lock,
so that shouldn't be an issue any more
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use $(FULL_AMD_PATH) like everything else.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
tdp_table is being leaked on failed allocations of
hwmgr->dyn_state.cac_dtp_table. kfree tdp_table on the error
return path to fix the leak.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The BXT display connections have DSI transcoders A and C that can be
muxed to any pipe, not unlike the eDP transcoder. Add the notion of DSI
transcoders.
The "normal" transcoders A, B and C are not used with BXT DSI, so care
must be taken to avoid accessing those registers with DSI transcoders in
the hardware state readout, modeset, and generally everywhere.
v2: addressing comments by Ville:
- rename the dsi get config function to hsw_get_dsi_transcoder_state
- rebase onto the higher level split of pipe/transcoder functions
- use more has_dsi_encoder as we can now because of the above,
with no need to look at the transcoder so much
- rename IS_DSI_TRANSCODER to transcoder_is_dsi
- use the above a bit more instead of comparing to < TRANSCODER_EDP
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/299740536b7941e31b2744f3ce34f7afe936a771.1458313400.git.jani.nikula@intel.com
Now that we can whitelist registers only on Haswell, move HSW_SCRATCH1
and HSW_ROW_CHICKEN3 into a separate Haswell only table.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Cc: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457335830-30923-4-git-send-email-jordan.l.justen@intel.com
For Haswell, we will want another table of registers while retaining
the large common table of whitelisted registers shared by all gen7
devices.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
[danvet: Pipe patch through sed -e 's/\<ring\>/engine/g' to make it
apply.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Christian König <christian.koenig@amd.com.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull x86 protection key support from Ingo Molnar:
"This tree adds support for a new memory protection hardware feature
that is available in upcoming Intel CPUs: 'protection keys' (pkeys).
There's a background article at LWN.net:
https://lwn.net/Articles/643797/
The gist is that protection keys allow the encoding of
user-controllable permission masks in the pte. So instead of having a
fixed protection mask in the pte (which needs a system call to change
and works on a per page basis), the user can map a (handful of)
protection mask variants and can change the masks runtime relatively
cheaply, without having to change every single page in the affected
virtual memory range.
This allows the dynamic switching of the protection bits of large
amounts of virtual memory, via user-space instructions. It also
allows more precise control of MMU permission bits: for example the
executable bit is separate from the read bit (see more about that
below).
This tree adds the MM infrastructure and low level x86 glue needed for
that, plus it adds a high level API to make use of protection keys -
if a user-space application calls:
mmap(..., PROT_EXEC);
or
mprotect(ptr, sz, PROT_EXEC);
(note PROT_EXEC-only, without PROT_READ/WRITE), the kernel will notice
this special case, and will set a special protection key on this
memory range. It also sets the appropriate bits in the Protection
Keys User Rights (PKRU) register so that the memory becomes unreadable
and unwritable.
So using protection keys the kernel is able to implement 'true'
PROT_EXEC on x86 CPUs: without protection keys PROT_EXEC implies
PROT_READ as well. Unreadable executable mappings have security
advantages: they cannot be read via information leaks to figure out
ASLR details, nor can they be scanned for ROP gadgets - and they
cannot be used by exploits for data purposes either.
We know about no user-space code that relies on pure PROT_EXEC
mappings today, but binary loaders could start making use of this new
feature to map binaries and libraries in a more secure fashion.
There is other pending pkeys work that offers more high level system
call APIs to manage protection keys - but those are not part of this
pull request.
Right now there's a Kconfig that controls this feature
(CONFIG_X86_INTEL_MEMORY_PROTECTION_KEYS) that is default enabled
(like most x86 CPU feature enablement code that has no runtime
overhead), but it's not user-configurable at the moment. If there's
any serious problem with this then we can make it configurable and/or
flip the default"
* 'mm-pkeys-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
x86/mm/pkeys: Fix mismerge of protection keys CPUID bits
mm/pkeys: Fix siginfo ABI breakage caused by new u64 field
x86/mm/pkeys: Fix access_error() denial of writes to write-only VMA
mm/core, x86/mm/pkeys: Add execute-only protection keys support
x86/mm/pkeys: Create an x86 arch_calc_vm_prot_bits() for VMA flags
x86/mm/pkeys: Allow kernel to modify user pkey rights register
x86/fpu: Allow setting of XSAVE state
x86/mm: Factor out LDT init from context init
mm/core, x86/mm/pkeys: Add arch_validate_pkey()
mm/core, arch, powerpc: Pass a protection key in to calc_vm_flag_bits()
x86/mm/pkeys: Actually enable Memory Protection Keys in the CPU
x86/mm/pkeys: Add Kconfig prompt to existing config option
x86/mm/pkeys: Dump pkey from VMA in /proc/pid/smaps
x86/mm/pkeys: Dump PKRU with other kernel registers
mm/core, x86/mm/pkeys: Differentiate instruction fetches
x86/mm/pkeys: Optimize fault handling in access_error()
mm/core: Do not enforce PKEY permissions on remote mm access
um, pkeys: Add UML arch_*_access_permitted() methods
mm/gup, x86/mm/pkeys: Check VMAs and PTEs for protection keys
x86/mm/gup: Simplify get_user_pages() PTE bit handling
...
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Drivers, especially i915.ko, can fail during the initial migration of a
dma-buf for CPU access. However, the error code from the driver was not
being propagated back to ioctl and so userspace was blissfully ignorant
of the failure. Rendering corruption ensues.
Whilst fixing the ioctl to return the error code from
dma_buf_start_cpu_access(), also do the same for
dma_buf_end_cpu_access(). For most drivers, dma_buf_end_cpu_access()
cannot fail. i915.ko however, as most drivers would, wants to avoid being
uninterruptible (as would be required to guarrantee no failure when
flushing the buffer to the device). As userspace already has to handle
errors from the SYNC_IOCTL, take advantage of this to be able to restart
the syscall across signals.
This fixes a coherency issue for i915.ko as well as reducing the
uninterruptible hold upon its BKL, the struct_mutex.
Fixes commit c11e391da2
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Feb 11 20:04:51 2016 -0200
dma-buf: Add ioctls to allow userspace to flush
Testcase: igt/gem_concurrent_blit/*dmabuf*interruptible
Testcase: igt/prime_mmap_coherency/ioctl-errors
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tiago Vignatti <tiago.vignatti@intel.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
CC: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: intel-gfx@lists.freedesktop.org
Cc: devel@driverdev.osuosl.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458331359-2634-1-git-send-email-chris@chris-wilson.co.uk
Merge second patch-bomb from Andrew Morton:
- a couple of hotfixes
- the rest of MM
- a new timer slack control in procfs
- a couple of procfs fixes
- a few misc things
- some printk tweaks
- lib/ updates, notably to radix-tree.
- add my and Nick Piggin's old userspace radix-tree test harness to
tools/testing/radix-tree/. Matthew said it was a godsend during the
radix-tree work he did.
- a few code-size improvements, switching to __always_inline where gcc
screwed up.
- partially implement character sets in sscanf
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
sscanf: implement basic character sets
lib/bug.c: use common WARN helper
param: convert some "on"/"off" users to strtobool
lib: add "on"/"off" support to kstrtobool
lib: update single-char callers of strtobool()
lib: move strtobool() to kstrtobool()
include/linux/unaligned: force inlining of byteswap operations
include/uapi/linux/byteorder, swab: force inlining of some byteswap operations
include/asm-generic/atomic-long.h: force inlining of some atomic_long operations
usb: common: convert to use match_string() helper
ide: hpt366: convert to use match_string() helper
ata: hpt366: convert to use match_string() helper
power: ab8500: convert to use match_string() helper
power: charger_manager: convert to use match_string() helper
drm/edid: convert to use match_string() helper
pinctrl: convert to use match_string() helper
device property: convert to use match_string() helper
lib/string: introduce match_string() helper
radix-tree tests: add test for radix_tree_iter_next
radix-tree tests: add regression3 test
...
Atm, in case failure injection forces an error the subsequent "*ERROR*
failed to init modeset" error message will make automated tests (CI)
report this event as a breakage even though the event is expected. To
fix this print the error message with debug log level in this case.
While at it print the error message for any init failure and change it
to
"""
Device initialization failed (errno)
Please file a bug at https://bugs.freedesktop.org/enter_bug.cgi?product=DRI
against DRM/Intel providing the dmesg log by booting with drm.debug=0xf
"""
and export a helper printing error messages using this same format.
A follow-up patch will convert all uses of DRM_ERROR reporting a user
facing problem to use this new helper instead.
v2:
- Include the problematic error message in the commit log, add a
request to file an fdo bug to the message (Chris)
v3:
- Include the new error message too in the commit log, make the
fdo link more precise and print part of the message with info log
level (Chris)
v4: (Chris)
- Use dev_printk instead of DRM_ERROR/INFO and use NOTICE instead of
INFO loglevel
- Export a helper for printing user facing error messages
v5:
- Keep the DRM_ERROR message prefix used by piglit-igt/CI to filter
relevant dmesg lines
- Use dev_notice(), instead of dev_printk(KERN_NOTICE,...)
v6:
- Print the fdo bug link only once (Chris)
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458290770-15480-1-git-send-email-imre.deak@intel.com
Throughout the code base, we use u32 for offsets into the global GTT. If
we ever see any hardware with a larger GGTT, then we run the real risk
of silent corruption. So test for our assumption up front so that we
have a nice reminder should the time come when it fails.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[Rebased and changed 1ull -> 1ULL, cut 80 char line]
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458290579-27783-1-git-send-email-joonas.lahtinen@linux.intel.com
Use less pointers with the probing code, making it much less confusing
to read.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Refer to Global GTT consistently as GGTT, thus rename dev_priv->gtt
to dev_priv->ggtt and struct i915_gtt to struct i915_ggtt.
Fix a couple of whitespace problems while at it.
v2:
- Fix a typo in commit message.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This allows writes to EU flow control registers. Together
with SIP code from the user-mode driver this resolves a
hang seen in some pre-emption scenarios. Note that this
patch is just the kernel mode part of this workaround.
v2. Oops, add FLOW_CONTROL_ENABLE macro to i915_reg.h.
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458144826-17269-1-git-send-email-tim.gore@intel.com
By reading the CSB (slow MMIO accesses) into a temporary local
buffer we can decrease the duration of holding the execlist
lock.
Main advantage is that during heavy batch buffer submission we
reduce the execlist lock contention, which should decrease the
latency and CPU usage between the submitting userspace process
and interrupt handling.
Downside is that we need to grab and relase the forcewake twice,
but as the below numbers will show this is completely hidden
by the primary gains.
Testing with "gem_latency -n 100" (submit batch buffers with a
hundred nops each) shows more than doubling of the throughput
and more than halving of the dispatch latency, overall latency
and CPU time spend in the submitting process.
Submitting empty batches ("gem_latency -n 0") does not seem
significantly affected by this change with throughput and CPU
time improving by half a percent, and overall latency worsening
by the same amount.
Above tests were done in a hundred runs on a big core Broadwell.
v2:
* Overflow protection to local CSB buffer.
* Use closer dev_priv in execlists_submit_requests. (Chris Wilson)
v3: Rebase.
v4: Added commend about irq needed to be disabled in
execlists_submit_request. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilsno <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458219586-20452-1-git-send-email-tvrtko.ursulin@linux.intel.com
Where we have a request we can use req->i915 directly instead
of going through the engine and device. Coccinelle script:
@@
function f;
identifier r;
@@
f(..., struct drm_i915_gem_request *r, ...)
{
...
- engine->dev->dev_private
+ r->i915
...
}
@@
struct drm_i915_gem_request *req;
@@
(
req->
- engine->dev->dev_private
+ i915
)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458219850-21007-1-git-send-email-tvrtko.ursulin@linux.intel.com
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
drivers/rtc: broken link fix
drm/i915 Fix typos in i915_gem_fence.c
Docs: fix missing word in REPORTING-BUGS
lib+mm: fix few spelling mistakes
MAINTAINERS: add git URL for APM driver
treewide: Fix typo in printk
The new helper returns index of the mathing string in an array. We
would use it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few other misc cleanups and bug fixes for 4.6. Highlights:
- unify endian handling in powerplay
- powerplay fixes
- fix a regression in 4.5 on boards with no display connectors
- fence cleanups and locking fixes
- whitespace cleanups and code refactoring in radeon
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux: (35 commits)
drm/amdgpu/gfx7: add MTYPE definition
drm/amdgpu: removing BO_VAs shouldn't be interruptible
drm/amd/powerplay: show uvd/vce power gate enablement for tonga.
drm/amd/powerplay: show uvd/vce power gate info for fiji
drm/amdgpu: use sched fence if possible
drm/amdgpu: move ib.fence to job.fence
drm/amdgpu: give a fence param to ib_free
drm/amdgpu: include the right version of gmc header files for iceland
drm/radeon: fix indentation.
drm/amd/powerplay: add uvd/vce dpm enabling flag to fix the performance issue for CZ
drm/amdgpu: switch back to 32bit hw fences v2
drm/amdgpu: remove amdgpu_fence_is_signaled
drm/amdgpu: drop the extra fence range check v2
drm/amdgpu: signal fences directly in amdgpu_fence_process
drm/amdgpu: cleanup amdgpu_fence_wait_empty v2
drm/amdgpu: keep all fences in an RCU protected array v2
drm/amdgpu: add number of hardware submissions to amdgpu_fence_driver_init_ring
drm/amdgpu: RCU protected amd_sched_fence_release
drm/amdgpu: RCU protected amdgpu_fence_release
drm/amdgpu: merge amdgpu_fence_process and _activity
...
Commit 8a2fa38fdd removed the mode_fixup because it was empty,
but 652353e6e5 modified it to call drm_mode_set_crtcinfo()
instead.
Both commits are correct, but the merge of the two kept the nonempty
version without the reference to it, as shown by the gcc warning:
drm/sti/sti_crtc.c:54:13: error: 'sti_crtc_mode_fixup' defined but not used
This restores the callback pointer to fix the merge.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reverts: 8a2fa38fdd ("drm/sti: removed optional dummy crtc mode_fixup function.")
Fixes: 652353e6e5 ("drm/sti: set CRTC modesetting parameters")
Fixes: cf481068cd ("Merge branch '2016-02-26-st-drm-next' of http://git.linaro.org/people/benjamin.gaignard/kernel into drm-next")
Acked-by: Vincent ABRIOU <vincent.abriou@st.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
when preemption feature lands, the SA bo should rely on sched
fence, because hw fence will be invalid after its job preempted
or skipped.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
thus amdgpu_ib_free() can hook sched fence to SA manager
in later patches.
BTW:
for amdgpu_free_job(), it should only fence_put() the
fence of the last ib once, so fix it as well in this patch.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for forcing an error at selected places in the driver. As an
example add 4 options to fail during driver loading.
Requested by Chris.
v2:
- Add fault point for modeset initialization
- Print debug message when injecting an error
v3:
- Rename inject_fault to inject_load_failure, rename the related macros
and helper accordingly (Chris)
- Use a counter instead of a mask to identify the failure point (Daniel)
- Mark the module option as _unsafe and keep i915_params ordered (Joonas)
v4:
- Rebase on latest -nightly
v5:
- Use DRM_INFO instead of DRM_DEBUG_DRIVER, making it clearer in CI reports
that a following error message is expected (IRC r-b from Chris on v5)
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the cleanup of the power domain HW state on the error path to the
same function where the corresponding init call was called from. I
noticed this problem when loading the module with load failure injection
enabled, making i915_load_modeset_init() fail.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-19-git-send-email-imre.deak@intel.com
According to the new init phases scheme we should register the device
making it available via some kernel internal or user space interface as
the last step in the init sequence, so move the corresponding code to a
separate function.
Also add a TODO comment about code that still needs to be moved around
to one of the init phases functions depending on what the role and effect
of that code is.
No functional change, except for the reordering of the unload time
unregistration steps of sysfs wrt. acpi and opregion.
Suggested by Chris.
v3:
- rename i915_driver_init_register to i915_driver_init_frameworks
(Chris)
- rename i915_driver_init_frameworks to i915_driver_register (Daniel)
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-18-git-send-email-imre.deak@intel.com
According to the new init phases scheme we should have a definite step
in the init sequence where we setup things requiring accessing the
device, so move the corresponding code to separate function. The steps
in this init phase should avoid exposing the driver via some interface,
which is done in the last registration init phase. This changae also
has the benefit of making the error path cleaner both in the new
function and i915_driver_load()/unload().
No functional change.
Suggested by Chris.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-17-git-send-email-imre.deak@intel.com
According to the new init phases scheme we should have a definite step
in the init sequence where MMIO access is setup, so move the
corresponding code to a separate function. This also has the benefit of
making the error path cleaner both in the new function and in
i915_driver_load()/unload().
No functional change.
Suggested by Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-16-git-send-email-imre.deak@intel.com
According to the new init phases scheme we should initialize "SW-only"
state not requiring accessing the device as the very first step, so that
the reasoning about dependencies of later steps becomes easier. So move
these init steps into a separate function. This also has the benefit of
making the error path cleaner both in the new function and int
i915_driver_load()/unload().
No functional change.
Suggested by Chris.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-15-git-send-email-imre.deak@intel.com
Move the power domain uninitialization later so that it matches its
corresponding init order. Since we access the HW during the later
unitialization steps keep a wake reference until after the last such
step.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-12-git-send-email-imre.deak@intel.com
According to the new init phases scheme we should register the driver
with frameworks/userspace only one the device is setup fully. So move
the shrinker registration later accordingly.
Also fix the shrinker unregistration order wrt. the acpi unregistration
to fix the corresponding init order.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-10-git-send-email-imre.deak@intel.com
The only steps requiring device access is the fence and swizzling
initialization, so split these out keeping them in their current place
and move the rest of init steps earlier.
v2-v3:
- unchanged
v4:
- move call to i915_gem_detect_bit_6_swizzle() to
i915_gem_load_init_fences() and preserve the original order of
the detection of HW fence capailities wrt. swizzling (Chris)
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458132843-21860-1-git-send-email-imre.deak@intel.com
Split out the part initing the clock gating hooks and move it earlier.
Add a new NOP hook for platforms without the need to apply clockgating
or workaround settings, so that the hook can be called unconditionally.
Also add a WARN for future platforms that forget to add a hook.
The rest of the hooks in intel_init_pm() should be inited in the same
way, but atm some of the hooks are set only conditionally, so before
doing this we need to make the setup unconditional and use instead some
flags.
v2:
- add a NOP hook and WARN if no hook is set for the platform (Chris)
- use the term hook instead of callback for these functions (Jani)
v3:
- remove the GEN4() check it's already covered by earlier platform
checks (Chris)
CC: Jani Nikula <jani.nikula@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-6-git-send-email-imre.deak@intel.com
All of this is SW only initialization so we can move them earlier. Move
the mutex init where the rest of the locks are inited. While at it also
convert dev to dev_priv.
v2:
- use the term hook instead of callback for these functions (Jani)
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-5-git-send-email-imre.deak@intel.com
These are all SW only init steps not accessing the device and they only
need the platform identification macros to work, which are already
available earlier, so move these init steps earlier.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-3-git-send-email-imre.deak@intel.com
MCHBAR is cleaned up in i915_mmio_cleanup(), so the separate call in
i915_driver_load() is incorrect.
CC: David Weinehall <david.weinehall@intel.com>
Fixes: ad5c3d3ffb ("drm/i915: Move MCHBAR setup earlier during init")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458128348-15730-2-git-send-email-imre.deak@intel.com
In full gpu reset we prime all engines and reset domains corresponding to
each engine. Per engine reset is just a special case of this process
wherein only a single engine is reset. This change is aimed to modify
relevant functions to achieve this. There are some other steps we carry out
in case of engine reset which are addressed in later patches.
Reset func now accepts a mask of all engines that need to be reset. Where
per engine resets are supported, error handler populates the mask
accordingly otherwise all engines are specified.
v2: ALL_ENGINES mask fixup, better for_each_ring_masked (Chris)
v3: Whitespace fixes (Chris)
v4: Rebase due to s/ring/engine
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458143640-20563-1-git-send-email-mika.kuoppala@intel.com
We've been accumulating code across the driver that depends on the VBT
specific structures and defines. The VBT is an uncontrollable
beast. Encourage encapsulation of the VBT data by hiding the structures
and defines in a private header only to be included from intel_bios.c.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458125015-7931-7-git-send-email-jani.nikula@intel.com
Warn for the wrong mask in enable only. Disable will have the wrong mask now
because the new state is committed before disabling the old state.
Changes since v1:
- Use crtc_mask (Durgadoss)
- Rebase.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
This makes it easier to verify correct dpll setup with only a single crtc.
It is also useful to detect double dpll enable/disable.
Changes since v1:
- Rebase on top of Ander's dpll rework.
- Change debugfs active to a mask.
- Change enabled_crtcs and active_crtcs to unsigned.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457944075-14123-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
After unplugging a DP MST display from the system, we have to go through
and destroy all of the DRM connectors associated with it since none of
them are valid anymore. Unfortunately, intel_dp_destroy_mst_connector()
doesn't do a good enough job of ensuring that throughout the destruction
process that no modesettings can be done with the connectors. As it is
right now, intel_dp_destroy_mst_connector() works like this:
* Take all modeset locks
* Clear the configuration of the crtc on the connector, if there is one
* Drop all modeset locks, this is required because of circular
dependency issues that arise with trying to remove the connector from
sysfs with modeset locks held
* Unregister the connector
* Take all modeset locks, again
* Do the rest of the required cleaning for destroying the connector
* Finally drop all modeset locks for good
This only works sometimes. During the destruction process, it's very
possible that a userspace application will attempt to do a modesetting
using the connector. When we drop the modeset locks, an ioctl handler
such as drm_mode_setcrtc has the oppurtunity to take all of the modeset
locks from us. When this happens, one thing leads to another and
eventually we end up committing a mode with the non-existent connector:
[drm:intel_dp_link_training_clock_recovery [i915]] *ERROR* failed to enable link training
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_dp_start_link_train [i915]] *ERROR* failed to start channel equalization
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x7cf0001f
[drm:intel_mst_pre_enable_dp [i915]] *ERROR* failed to allocate vcpi
And in some cases, such as with the T460s using an MST dock, this
results in breaking modesetting and/or panicking the system.
To work around this, we now unregister the connector at the very
beginning of intel_dp_destroy_mst_connector(), grab all the modesetting
locks, and then hold them until we finish the rest of the function.
CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458155884-13877-1-git-send-email-cpaul@redhat.com
Here are sti patches for drm-next.
It brings:
- The support of the atomic_check for the planes and minor fixes for
planes
- The support of the vendor specific infoframe for HDMI and the
support of 2 HDMI properties related to the connector
- The support of the DVO solving panel detection issue and timing issue.
- The support of debugfs for connectors, encoders, crtcs and planes.
* '2016-02-26-st-drm-next' of http://git.linaro.org/people/benjamin.gaignard/kernel: (36 commits)
drm/sti: use u32 to store DMA addresses
drm: sti: remove sti_gem_prime_export hack
drm/sti: add debugfs fps_show/fps_get mechanism for planes
drm/sti: add debugfs entries for TVOUT encoders
drm/sti: add debugfs entries for MIXER crtc
drm/sti: add debugfs entries for VID plane
drm/sti: add debugfs entries for HQVDP plane
drm/sti: add debugfs entries for GDP planes
drm/sti: add debugfs entries for CURSOR plane
drm/sti: add debugfs entries for HDA connector
drm/sti: add debugfs entries for DVO connector
drm/sti: add debugfs entries for HDMI connector
drm/sti: add hdmi_mode property for HDMI connector
drm/sti: add colorspace property to the HDMI connector
drm/sti: add HDMI vendor specific infoframe
drm/sti: reset infoframe transmission when HDMI is stopped
drm/sti: HDMI infoframe transmission mode not take into account
drm/sti: reset HD DACS when HDA connector is created
drm/sti: fix dvo data_enable signal
drm/sti: adjust delay for DVO
...
This version of GuC firmware fixes the engine reset issue where golden
context LRC address is treated as page index by mistake. It also fixes
the problem that scheduler stops submiting to one engine when the other
engine work queue is full.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
A few more fixes and cleanups for 4.6:
- DCE code cleanups
- HDP flush/invalidation fixes
- GPUVM fixes
- switch to drm_vblank_[on|off]
- PX fixes
- misc bug fixes
* 'drm-next-4.6' of git://people.freedesktop.org/~agd5f/linux: (50 commits)
drm/amdgpu: split pipeline sync out of SDMA vm_flush() as well
drm/amdgpu: Revert "add mutex for ba_va->valids/invalids"
drm/amdgpu: Revert "add lock for interval tree in vm"
drm/amdgpu: Revert "add spin lock to protect freed list in vm (v3)"
drm/amdgpu: reserve the PD during unmap and remove
drm/amdgpu: Fix two bugs in amdgpu_vm_bo_split_mapping
drm/radeon: Don't drop DP 2.7 Ghz link setup on some cards.
MAINTAINERS: update radeon entry to include amdgpu as well
drm/amdgpu: disable runtime pm on PX laptops without dGPU power control
drm/radeon: disable runtime pm on PX laptops without dGPU power control
drm/amd/amdgpu: Fix indentation in do_set_base() (DCEv8)
drm/amd/amdgpu: make afmt_init cleanup if alloc fails (DCEv8)
drm/amd/amdgpu: Move config init flag to bottom of sw_init (DCEv8)
drm/amd/amdgpu: Don't proceed into audio_fini if audio is disabled (DCEv8)
drm/amd/amdgpu: Fix identation in do_set_base() (DCEv10)
drm/amd/amdgpu: Make afmt_init cleanup if alloc fails (DCEv10)
drm/amd/amdgpu: Move initialized flag to bottom of sw_init (DCEv10)
drm/amd/amdgpu: Don't proceed in audio_fini if disabled (DCEv10)
drm/amd/amdgpu: Fix indentation in dce_v11_0_crtc_do_set_base()
drm/amd/amdgpu: Make afmt_init() cleanup if alloc fails (DCEv11)
...
Pull request of 2016-03-16
* tag 'vmwgfx-next-160316' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Bump driver minor
drm/vmwgfx: Allow the UPDATE_LAYOUT ioctl from control nodes
drm/vmwgfx: Send a hotplug event at master_set
drm/vmwgfx: Default to explicit crtc placement for screen targets and screen objects
drm/vmwgfx: Calculate the cursor position based on the crtc gui origin
drm/vmwgfx: Add connector properties to switch between explicit and implicit placement
drm/vmwgfx: Add suggested screen x and y connector properties
drm/vmwgfx: Add implicit framebuffer checks to the screen target code
drm/vmwgfx: Break out implicit fb code
drm/vmwgfx: Rework screen target page flips v2
drm/vmwgfx: Fix screen object page flips for large framebuffers
drm/vmwgfx: Fix a screen object framebuffer dirty corner case
drm/vmwgfx: Add DXGenMips support
This contains a refactoring of parts of the DSI core to allow creating
DSI devices from non-DSI control busses (i.e. I2C, SPI, ...).
Other than that there's support for a couple of new panels as well as
a few cleanup patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJW6Vc2AAoJEN0jrNd/PrOhh98P+wdrQqsctsSHFuaCpQ9mpgpO
qj8M9R1wfeT279e7HpmI0HEWfoPJtC+G2uzIqhmLyBmM9YJIbJK5Bwh6jsYZoNwV
Nx4hpBTBW5lwhJGrttDYVyvox+JO2TVcP2/8g4JHBmRd7UHddyeynhBZTAia5xoW
2sfSs3YgkWzVoTXlWPBAliNHZIoA5DOClO3W5n60ubeIB4nVWHhjwA6SX19tkI8U
hUWbazJVwtt9C4UP32fxa5fgViJjT3X0HX9qEk7Wr4CJ85j4dvVrjX/vI++qFSFI
YE8/zUZS9k2qe8cJWokGpHgiSOAX7+9IA8aZMGxS3tN9fFrUU11vSjVY/nrboFFP
8NRYC/wC6nd7D7ri0b/yNMPefFfwzCYDubGFAwvGKVXjbd/uwZE3jhLuL0bvICvG
QVwhOG5ghbBWigie4bwD41GCRrk2pIuh/EefDSAPYmka4MC53CGWFpFXLs1aRVxL
CVbaUzFkcqMpU/gDUuPZk2qDcmBat6yG0wcmX5rUIvUVUNTQKkMUSSEH2dxp7fsV
YmXu9orGNgnM45Q92e7tVaBEw1sNWyDhdFaLk4QX9I+No2n4JMk14pxH7VuNXufR
EqVafpOxregXDaH9Xtg/jVvW1AF+IH/t3S2uuqhRmP6tLQL0kAhnwh1zgDp1o/Pb
pC8GiBIt5hzQApOxyYPI
=zrRb
-----END PGP SIGNATURE-----
Merge tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux into drm-next
drm/panel: Changes for v4.6-rc1
This contains a refactoring of parts of the DSI core to allow creating
DSI devices from non-DSI control busses (i.e. I2C, SPI, ...).
Other than that there's support for a couple of new panels as well as
a few cleanup patches.
* tag 'drm/panel/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux:
drm/bridge: Make (pre/post) enable/disable callbacks optional
drm/panel: simple: Add URT UMSH-8596MD-xT panels support
dt-bindings: Add URT UMSH-8596MD-xT panel bindings
of: Add United Radiant Technology Corporation vendor prefix
drm/panel: simple: Support for LG lp120up1 panel
dt-bindings: Add LG lp120up1 panel bindings
drm/panel: simple: Fix g121x1_l03 hsync/vsync polarity
drm/dsi: Get DSI host by DT device node
drm/dsi: Add routine to unregister a DSI device
drm/dsi: Try to match non-DT DSI devices
drm/dsi: Use mipi_dsi_device_register_full() for DSI device creation
drm/dsi: Check for CONFIG_OF when defining of_mipi_dsi_device_add()
Only two cleanups this time around. One fixes reference counting of
device tree nodes, the other changes the return value of a function
from an unsigned int to an int to reflect that it will return error
codes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=i5YM
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux into drm-next
drm/tegra: Changes for v4.6-rc1
Only two cleanups this time around. One fixes reference counting of
device tree nodes, the other changes the return value of a function
from an unsigned int to an int to reflect that it will return error
codes.
* tag 'drm/tegra/for-4.6-rc1' of http://anongit.freedesktop.org/git/tegra/linux:
gpu: host1x: Use a signed return type for do_relocs()
gpu: host1x: bus: Add missing of_node_put()
I hate doing this but it hurts my eyes to go over code that does not
comply with indentation rules. Only thing that is not only space change
is in atom.c all other files are space indentation issues.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the UVD and VCE DPM flags otherwise UVD and VCE DPM won't get enabled.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Cc: stable@vger.kernel.org
We don't need to extend them to 64bits any more, so avoid the extra overhead.
v2: update commit message.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
It's just overhead to check the fence value
when we signal them directly anyway.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Amdgpu doesn't support using scratch registers for fences any more.
So we won't see values like 0xdeadbeef as fence value any more.
v2: reschedule timer even if no change detected
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Because of the scheduler we need to signal all fences immediately
anyway, so try to avoid the waitqueue overhead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Just wait for last fence instead of waiting for the sequence manually.
v2: don't use amdgpu_sched_jobs for the mask
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Just keep all HW fences in a RCU protected array as a
first step to replace the wait queue.
v2: update commit message, move fixes into separate patch.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Make this a parameter instead of using the global variable directly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Fences must be freed RCU protected, otherwise the reservation_object_*_rcu()
functions can run into problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Fences must be freed RCU protected, otherwise the reservation_object_*_rcu()
functions can run into problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The comment about the loop counter was never valid, even when you have
multiple threads this loop only runs as long as the sequence increases.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Liu Ying