These are the current arm-soc bug fixes for linux-5.11. I already merged
a larger set that just came in during the past three days but has not
had much exposure in linux-next, so these are the ones I merged last week.
Most of these are for the NXP i.MX platform (descriptions from their
pull request):
- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
Aside from i.MX, the bugfixes are all over the place:
- Coccinelle found a refcount imbalance on integrator
- defconfig fix for TI K3
- A boot regression fix for ST ux500
- A code preemption fix for the optee driver
- USB DMA regression on Broadcom Stingray
- A bogus boot time warning fix for at91 code
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=Vneq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are the current arm-soc bug fixes for linux-5.11. I already
merged a larger set that just came in during the past three days but
has not had much exposure in linux-next, but this is the subset I
merged last week.
Most of these are for the NXP i.MX platform (descriptions from their
pull request):
- Fix pcf2127 reset for imx7d-flex-concentrator board.
- Fix i.MX6 suspend with Thumb-2 kernel.
- Fix ethernet-phy address issue on imx6qdl-sr-som board.
- Fix GPIO3 `gpio-ranges` on i.MX8MP.
- Select SOC_BUS for IMX_SCU driver to fix build issue.
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build
failure with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
Aside from i.MX, the bugfixes are all over the place:
- Coccinelle found a refcount imbalance on integrator
- defconfig fix for TI K3
- A boot regression fix for ST ux500
- A code preemption fix for the optee driver
- USB DMA regression on Broadcom Stingray
- A bogus boot time warning fix for at91 code"
* tag 'arm-soc-fixes-v5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: Include bcm2835 subsequents into search
arm64: dts: broadcom: Fix USB DMA address translation for Stingray
drivers: soc: atmel: add null entry at the end of at91_soc_allowed_list[]
drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs
tee: optee: replace might_sleep with cond_resched
firmware: imx: select SOC_BUS to fix firmware build
arm64: dts: imx8mp: Correct the gpio ranges of gpio3
ARM: dts: imx6qdl-sr-som: fix some cubox-i platforms
ARM: imx: build suspend-imx6.S with arm instruction set
ARM: dts: imx7d-flex-concentrator: fix pcf2127 reset
ARM: dts: ux500: Reserve memory carveouts
arm64: defconfig: Drop unused K3 SoC specific options
bus: arm-integrator-lm: Add of_node_put() before return statement
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
-----BEGIN PGP SIGNATURE-----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=KgUu
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps for v5.11-rc cycle
The recent changes to switch SoCs to boot with ti-sysc interconnect
target module driver and genpd caused few regressions:
- The omap_prm reset driver needs to clear any reset bits deasserted by
the bootloader or kexec boot for the three reset bit cases. Otherwise
we can have an oops with accelerators starting to boot with potentially
unconfigured MMU for example
- Custom kernel configs are not automatically selecting simple-pm-bus
driver that we now need to probe interconnects so we need to select it
always
- We are not passing legacy platform data in auxdata with simple-pm-bus
like we do for simple-bus. We need to pass auxdata to simple-pm-bus so
it can pass it to of_platform_populate()
Then recent RCU changes started causing splats for cpuidle44xx that now
need RCU_NONIDLE added to the calls in several places
And then we have few device specific fixes:
- We need to remove legacy spi-cs-hig for gta04 display to work, and
set the gpio to active low
- Omap1 specific ohci-omap needs to call gpio_free()
- Droid4 needs to use padconf interrupt for the slider as the edge
gpio interrupts may be lost for deeper idle states
* tag 'omap-for-v5.11/fixes-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix lost keypad slide interrupts for droid4
drivers: bus: simple-pm-bus: Fix compatibility with simple-bus for auxdata
ARM: OMAP2+: Fix booting for am335x after moving to simple-pm-bus
ARM: OMAP2+: Fix suspcious RCU usage splats for omap_enter_idle_coupled
ARM: dts; gta04: SPI panel chip select is active low
soc: ti: omap-prm: Fix boot time errors for rst_map_012 bits 0 and 1
ARM: OMAP1: OSK: fix ohci-omap breakage
DTS: ARM: gta04: remove legacy spi-cs-high to make display work again
Link: https://lore.kernel.org/r/pull-1611818709-243493@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The DE2 display engine hardware takes physical addresses that do not
need PHYS_BASE subtracted. As a result, they should not be present
on the mbus driver match list. Remove them.
This was tested on the A83T, along with the patch allowing the DMA
range map to be non-NULL and restores a working display.
Fixes: b4bdc4fbf8 ("soc: sunxi: Deal with the MBUS DMA offsets in a central place")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210115175831.1184260-2-paul.kocialkowski@bootlin.com
The Allwinner H616 adds a second EMAC clock register at offset 0x34, for
controlling the second EMAC in this chip.
Allow to extend the regmap in this case, to cover more than the current
4 bytes exported.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210127172500.13356-9-andre.przywara@arm.com
Remove extra le32_to_cpu() conversion, data is already converted from
le32 to cpu endianness. This fixes two following warnings:
drivers/soc/qcom/socinfo.c:322:36: sparse: sparse: cast to restricted __le32
drivers/soc/qcom/socinfo.c:323:36: sparse: sparse: cast to restricted __le32
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 734c78e7fe ("soc: qcom: socinfo: add info from PMIC models array")
Link: https://lore.kernel.org/r/20210118152236.514776-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We have no in tree or out of tree users of this function, remove it and
the header providing its prototype.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
SAMA7G5 has different masks for chip ID and chip version on CIDR
register compared to previous AT91 SoCs. For this the commit adapts
the code for SAMA7G5 addition by introducing 2 new members in
struct at91_soc and fill them properly and also preparing the
parsing of proper DT binding.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1611318097-8970-6-git-send-email-claudiu.beznea@microchip.com
of_match_node() calls __of_match_node() which loops though the entries of
matches array. It stops when condition:
(matches->name[0] || matches->type[0] || matches->compatible[0]) is
false. Thus, add a null entry at the end of at91_soc_allowed_list[]
array.
Fixes: caab13b496 ("drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs")
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
MSM8994 uses similar to MSM8996, legacy-style voltage
control, but does not include a VDD_SC_CX line.
This setup is also correct for MSM8992.
Do note that there exist some boards that use a tertiary PMIC
(most likely pm8004), where SMPB on VDDGFX becomes SMPC. I
cannot test this configuration though.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210118161943.105733-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The pruss_clk_init() function can register more than one clock.
Correct the existing misleading error trace upon a failure within
this function.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
'am33xx_pm_rtc_setup()' allocates some resources that must be freed on the
error. Commit 2152fbbd47 ("soc: ti: pm33xx: Simplify RTC usage to prepare
to drop platform data") has introduced the use of these resources but has
only updated the remove function.
Fix the error handling path of the probe function now.
Fixes: 2152fbbd47 ("soc: ti: pm33xx: Simplify RTC usage to prepare to drop platform data")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
for_each_child_of_node increases refcount for each device_node and decreases previous one
in a loop, but in case jump out of a loop current node refcount has no chnase for decreases
so requires an of_node_put for jupm out cases.
Fix based on raport from
scripts/coccinelle/iterators/for_each_child.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Pickup fixes that went upstream already in order to resolve conflicts in
litex_soc_ctrl.c between 5.11 fixes that went upstream and the
or1k-5.12-updates linux-next queue.
Signed-off-by: Stafford Horne <shorne@gmail.com>
of_match_node() calls __of_match_node() which loops though the entries of
matches array. It stops when condition:
(matches->name[0] || matches->type[0] || matches->compatible[0]) is
false. Thus, add a null entry at the end of at91_soc_allowed_list[]
array.
Fixes: caab13b496 ("drivers: soc: atmel: Avoid calling at91_soc_init on non AT91 SoCs")
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since at91_soc_init is called unconditionally from atmel_soc_device_init,
we get the following warning on all non AT91 SoCs:
" AT91: Could not find identification node"
Fix the same by filtering with allowed AT91 SoC list.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #4.12+
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201211135846.1334322-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a helper that takes a virtual address rather than the muram
offset. This will be used in a couple of places to avoid having to
store both the offset and the virtual address, as well as removing
NULL checks from the callers.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The two functions cpm_muram_offset() and cpm_muram_dma() both need a
cast currently, one casts muram_vbase to do the pointer arithmetic on
void pointers, the other casts the passed-in address u8*.
It's simpler and more consistent to just always use void* and drop all
the casting.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow passing const-qualified pointers without requiring a cast in the
caller.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Let the LiteX SoC Controller register a restart handler, which resets
the LiteX SoC by writing 1 to CSR_CTRL_RESET_ADDR.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stafford Horne <shorne@gmail.com>
These need to be < ARRAY_SIZE() instead of <= ARRAY_SIZE() to prevent
accessing one element beyond the end of the array.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: e9247e2ce5 ("soc: qcom: socinfo: fix printing of pmic_model")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YAf+o85Z9lgkq3Nw@mwanda
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There is an off-by-one array index bounds check on array
pmic_models. Fix this by checking using < rather than <= on
the array size.
Addresses-Coverity: ("Out-of-bounds read")
Fixes: 734c78e7fe ("soc: qcom: socinfo: add info from PMIC models array")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210118113651.71955-1-colin.king@canonical.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The ZTE ZX set-top-box SoC platform was added in 2015 by Jun Nie, with
Baoyou Xie and Shawn Guo subsequently becoming maintainers after the
addition of the 64-bit variant.
However, the only machines that were ever supported upstream are the
reference designs, not actual set-top-box devices that would benefit
from this support. All ZTE set-top-boxes from the past few years seem
to be based on third-party SoCs. While there is very little information
about zx296702 and zx296718 on the web, I found some references to other
chips from the same family, such as zx296716 and zx296719, which were
never submitted for upstream support. Finally, there is no support for
the GPU on either of them, with the lima and panfrost device drivers
having been added after work on the zx platform had stopped.
Shawn confirmed that he has not seen any interest in this platform for
the past four years, and that it can be removed.
Thanks to Jun and Shawn for maintaining this platform over the past
five years.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When Exynos power domain driver was introduced, the only way to ensure
that power domains will be instantiated before the devices which belongs
to them was to initialize them early enough, before the devices are
instantiated in the system. This in turn required not to use any platform
device infrastructure at all, as there have been no way to ensure proper
probe order between devices.
This has been finally changed and upcomming patch "driver core: Set
fw_devlink=on by default" ensures that each device will be probbed only
when its resource providers are ready. This allows to convert Exynos
power domain driver to regular platform driver.
This is also required by the mentioned commit to enable probing any
device which belongs to the Exynos power domains, as otherwise the core
won't notice that the power domains are in fact available.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20210113110320.13149-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There doesn't seem to be any reason to limit this to only root user
readable. Let's make it readable by all so that random programs can
read the debugfs files in here instead of just root. The information is
just that, informational, so this is fine.
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20201216071926.3147108-1-swboyd@chromium.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce the header file include/soc/canaan/k210-sysctl.h to have a
common definition of the Canaan Kendryte K210 SoC system controller
registers. Simplify the k210 system controller driver code by removing
unused register bits definition. The MAINTAINERS file is updated,
adding the entry "CANAAN/KENDRYTE K210 SOC SYSTEM CONTROLLER DRIVER"
with myself listed as maintainer for this driver.
This is a preparatory patch for introducing the K210 clock driver. No
functional changes are introduced.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Rename configuration options and directories related to the Kendryte
K210 SoC to use the SoC vendor name (canaan) instead of the "kendryte"
branding name.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The 'litex_[set|get]_reg()' methods use the 'reg_size' parameter to
specify the width of the LiteX CSR (MMIO) register being accessed.
Since 'u64' is the widest data being supported, the value of 'reg_size'
MUST be between 1 and sizeof(u64), which SHOULD be checked at runtime
if these methods are publicly available for use by other LiteX device
drivers.
At the same time, none of the existing (or foreseeable) LiteX device
drivers have a need to access registers whose size is unknown during
compilation. As such, all LiteX device drivers should use fixed-width
accessor methods such as 'litex_[write|read][8|16|32|64]()'.
This patch renames 'litex_[set|get]_reg()' to '_litex_[set|get]_reg()',
indicating that they should NOT be directly called from outside of
the 'include/linux/litex.h' header file.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Upstream LiteX now defaults to using 32-bit CSR subregisters
(see https://github.com/enjoy-digital/litex/commit/a2b71fde).
This patch expands on commit 22447a99c9 ("drivers/soc/litex: add
LiteX SoC Controller driver"), adding support for handling both 8-
and 32-bit LiteX CSR (MMIO) subregisters, as determined by the
LITEX_SUBREG_SIZE Kconfig option.
NOTE that while LITEX_SUBREG_SIZE could theoretically be a device
tree property, defining it as a compile-time constant allows for
much better optimization of the resulting code. This is further
supported by the low expected usefulness of deploying the same
kernel across LiteX SoCs built with different CSR-Bus data widths.
Finally, the litex_[read|write][8|16|32|64]() accessors are
redefined in terms of litex_[get|set]_reg(), which, after compiler
optimization, will result in code as efficient as hardcoded shifts,
but with the added benefit of automatically matching the appropriate
LITEX_SUBREG_SIZE.
NOTE that litex_[get|set]_reg() nominally operate on 64-bit data,
but that will also be optimized by the compiler in situations where
narrower data is used from a call site.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Move generic LiteX CSR (MMIO) register accessors to litex.h and
declare them as "static inline", in preparation for supporting
32-bit CSR subregisters and 64-bit CPUs.
NOTE: this is a non-functional change.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
The test robot reported:
drivers/soc/litex/litex_soc_ctrl.c:143:34: warning: unused variable 'litex_soc_ctrl_of_match' [-Wunused-const-variable]
static const struct of_device_id litex_soc_ctrl_of_match[] = {
^
1 warning generated.
As per the random config device tree is not configured causing the
litex_soc_ctrl_of_match match list to not be used. This would usually
mean that we cannot even use this driver as it depends on device tree,
but as we also have COMPILE_TEST configured we allow it.
Fix the warning by surrounding the unused variable with an ifdef
CONFIG_OF.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Stafford Horne <shorne@gmail.com>
PMB originally comes from BCM63138 but can be also found on many other
chipsets (e.g. BCM4908). It's needed to power on and off SoC blocks like
PCIe, SATA, USB.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Directly reading ocotp register depends on that bootloader enables ocotp
clk, which is not always effective, so change to use nvmem API. Using
nvmem API requires to support driver defer probe and thus change
soc-imx8m.c to use platform driver.
The other reason is that directly reading ocotp register causes kexec
kernel hang because the 1st kernel running will disable unused clks
after kernel boots up, and then ocotp clk will be disabled even if
bootloader enables it. When kexec kernel, ocotp clk needs to be enabled
before reading ocotp registers, and nvmem API with platform driver
supported can accomplish this.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Selecting ARM_GIC_V3 on non-CP15 processors leads to build failures
like
arch/arm/include/asm/arch_gicv3.h: In function 'write_ICC_AP1R3_EL1':
arch/arm/include/asm/arch_gicv3.h:36:40: error: 'c12' undeclared (first use in this function)
36 | #define __ICC_AP1Rx(x) __ACCESS_CP15(c12, 0, c9, x)
| ^~~
Add a dependency to only enable the gic driver when building for
at an ARMv7 target, which is the closes approximation to the ARMv8
processor that is actually in this chip.
Fixes: fc40200ebf ("soc: imx: increase build coverage for imx8m soc driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After converting to builtin driver, the probe function should not call
__init functions anymore:
>> WARNING: modpost: vmlinux.o(.text+0x8884d4):
Section mismatch in reference from the function exynos_chipid_probe() to the function .init.text:product_id_to_soc_id()
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 352bfbb3e0 ("soc: samsung: exynos-chipid: convert to driver and merge exynos-asv")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210105174440.120041-1-krzk@kernel.org
All SiPeed K210 MAIX boards have the exact same vendor, arch and
implementation IDs, preventing differentiation to select the correct
device tree to use through the SOC_BUILTIN_DTB_DECLARE() macro. This
result in this macro to be useless and mandates changing the code of
the sysctl driver to change the builtin device tree suitable for the
target board.
Fix this problem by removing the SOC_BUILTIN_DTB_DECLARE() macro since
it is used only for the K210 support. The code searching the builtin
DTBs using the vendor, arch an implementation IDs is also removed.
Support for builtin DTB falls back to the simpler and more traditional
handling of builtin DTB using the CONFIG_BUILTIN_DTB option, similarly
to other architectures.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
SiFive FU740 has 4 ECC interrupt sources as compared to 3 in FU540.
Update the L2 cache controller driver to support this additional
interrupt in case of FU740-C000 chip.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Requests sent to RPMH can be sent as fire-n-forget or response required,
with the latter ensuring the command has been completed by the hardware
accelerator. Commands in a request with tcs_cmd::wait set, would ensure
that those select commands are sent as response required, even though
the actual TCS request may be fire-n-forget.
Also, commands with .wait flag were also guaranteed to be complete
before the following command in the TCS is sent. This means that the
next command of the same request blocked until the current request is
completed. This could mean waiting for a voltage to settle or series of
NOCs be configured before the next command is sent. But drivers using
this feature have never cared about the serialization aspect. By not
enforcing the serialization we can allow the hardware to run in parallel
improving the performance.
Let's clarify the usage of this member in the tcs_cmd structure to mean
only completion and not serialization. This should also improve the
performance of bus requests where changes could happen in parallel.
Also, CPU resume from deep idle may see benefits from certain wake
requests.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1610008770-13891-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Exynos Chip ID driver on Exynos SoCs has so far only informational
purpose - to expose the SoC device in sysfs. No other drivers depend on
it so there is really no benefit of initializing it early.
The code would be the most flexible if converted to a regular driver.
However there is already another driver - Exynos ASV (Adaptive Supply
Voltage) - which binds to the device node of Chip ID.
The solution is to convert the Exynos Chip ID to a built in driver and
merge the Exynos ASV into it.
This has several benefits:
1. Although the Exynos ASV driver binds to a device node present in all
Exynos DTS (generic compatible), it fails to probe except on the
supported ones (only Exynos5422). This means that the regular boot
process has a planned/normal device probe failure.
Merging the ASV into Chip ID will remove this probe failure because
the final driver will always bind, just with disabled ASV features.
2. Allows to use dev_info() as the SoC bus is present (since
core_initcall).
3. Could speed things up because of execution of Chip ID code in a SMP
environment (after bringing up secondary CPUs, unlike early_initcall),
This reduces the amount of work to be done early, when the kernel has
to bring up critical devices.
5. Makes the Chip ID code defer-probe friendly,
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201207190517.262051-5-krzk@kernel.org
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
If regmap_read() fails, the product_id local variable will contain
random value from the stack. Do not try to parse such value and fail
the ASV driver probe.
Fixes: 5ea428595c ("soc: samsung: Add Exynos Adaptive Supply Voltage driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20201207190517.262051-3-krzk@kernel.org
Check if the SoC is really supported before gathering the needed
resources. This fixes endless deferred probe on some SoCs other than
Exynos5422 (like Exynos5410).
Fixes: 5ea428595c ("soc: samsung: Add Exynos Adaptive Supply Voltage driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20201207190517.262051-2-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We have rst_map_012 used for various accelerators like dsp, ipu and iva.
For these use cases, we have rstctrl bit 2 control the subsystem module
reset, and have and bits 0 and 1 control the accelerator specific
features.
If the bootloader, or kexec boot, has left any accelerator specific
reset bits deasserted, deasserting bit 2 reset will potentially enable
an accelerator with unconfigured MMU and no firmware. And we may get
spammed with a lot by warnings on boot with "Data Access in User mode
during Functional access", or depending on the accelerator, the system
can also just hang.
This issue can be quite easily reproduced by setting a rst_map_012 type
rstctrl register to 0 or 4 in the bootloader, and booting the system.
Let's just assert all reset bits for rst_map_012 type resets. So far
it looks like the other rstctrl types don't need this. If it turns out
that the other type rstctrl bits also need reset on init, we need to
add an instance specific reset mask for the bits to avoid resetting
unwanted bits.
Reported-by: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When triggering a TCS to send its contents, reading back the trigger
value may return an incorrect value. That is because, writing the
trigger may raise an interrupt which could be handled immediately and
the trigger value could be reset in the interrupt handler.
A write_tcs_reg_sync() would read back the value that is written and try
to match it to the value written to ensure that the value is written,
but if that value is different, we may see false error for same.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1606211610-15168-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SM8250 SoC uses LLCC IP version 2. In this version, the WRSC_EN register
needs to be written to enable the Write Sub Cache for each SCID. Hence,
use a dedicated "write_scid_en" member with predefined values and write
them for LLCC IP version 2.
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20201130093924.45057-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The major hardware version of the LLCC IP is encoded in its
LLCC_COMMON_HW_INFO register. Extract the version and cache it in the
driver data so that it can be used to implement version specific
functionality like enabling Write sub cache for given SCID.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
[mani: splitted the version extract as a single patch and few cleanups]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20201130093924.45057-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since at91_soc_init is called unconditionally from atmel_soc_device_init,
we get the following warning on all non AT91 SoCs:
" AT91: Could not find identification node"
Fix the same by filtering with allowed AT91 SoC list.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201211135846.1334322-1-sudeep.holla@arm.com
This series adds:
* New drivers and OpenRISC support for the LiteX platform
* A bug fix to support userspace gdb debugging
* Fixes one compile issue with blk-iocost
-----BEGIN PGP SIGNATURE-----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=zTkl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
- New drivers and OpenRISC support for the LiteX platform
- A bug fix to support userspace gdb debugging
- Fixes one compile issue with blk-iocost
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: add local64.h to fix blk-iocost build
openrisc: fix trap for debugger breakpoint signalling
openrisc: add support for LiteX
drivers/tty/serial: add LiteUART driver
dt-bindings: serial: document LiteUART bindings
drivers/soc/litex: add LiteX SoC Controller driver
dt-bindings: soc: document LiteX SoC Controller bindings
dt-bindings: vendor: add vendor prefix for LiteX
New drivers/devices
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
- Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI keystone drivers for 5.11 included here due to dependency for TI
drivers
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAl/bkxEACgkQfBQHDyUj
g0dxNA//WzpVy9QJnj6OgXIjM+9sBjqls0iPVfy1JeeMmVW8cgCwLyBNZcssKRye
mJ9+VnTx4JQBj4KD2cFBdpr46GvBFbSbcWNSCdm179NtHI4G6tjtynOcWaI9Clu2
0KHoa/EHIj8/jD3Hsbm+WZ1zCoY4VKBXsEq6x1Sj2tpp0/ocDhH4XLAsWTHE9OAD
sc+0OtHr1wU4EdV6TKNTT0jXsdtzxOPPsvRsoaKncnR+Mkrgv0FvMBfBLhOb3a+m
wUHEkwrEP1pT4Xcew6ZkYs4RYwJI3pllu2gUTs5qtidc723ol/C4kJ27q55N4azb
j5buA8AhEwqIDH8qNuV07qaIu2VTdTdbYid3xgAeFygwM1npecZvOf8k6rTjxR/6
XN8jaDuhc2uISY7Gt5c6tOe8rG3ffNhYrmEuGD5HI0hcglpALiE4NcgalaaQS9J1
suQ6AUtCslReD+6M/lfarn9Zd3UAKGbxU8vCNPq0EcSAGUz9u9VK2VwKiGnAZ8bb
ED3QDUzZYjTDWpiVodsuJlONgaMLsRCQecZWMDRNpzmf1rCXnkY0eDGiSMz+IiXZ
87IdD66u3d/Mkm6jVdwp6+tKZ/ohj+dtIWKhMd8cKXv5zTzS+4IokxpkxdjBsHPx
z+G73IMHjQo8xl/P0IhhwZw+7cBrkntLq8lRSbYxjSTP09QerNE=
=uNBn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"The last dmaengine updates for this year :)
This contains couple of new drivers, new device support and updates to
bunch of drivers.
New drivers/devices:
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI drivers"
* tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (75 commits)
soc: ti: k3-ringacc: Use correct error casting in k3_ringacc_dmarings_init
dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA
dmaengine: ti: k3-udma: Initial support for K3 PKTDMA
dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling
dmaengine: ti: k3-udma: Initial support for K3 BCDMA
soc: ti: k3-ringacc: add AM64 DMA rings support.
dmaengine: ti: Add support for k3 event routers
dmaengine: ti: k3-psil: Add initial map for AM64
dmaengine: ti: k3-psil: Extend psil_endpoint_config for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 BCDMA
dmaengine: dmatest: Use dmaengine_get_dma_device
dmaengine: doc: client: Update for dmaengine_get_dma_device() usage
dmaengine: Add support for per channel coherency handling
dmaengine: of-dma: Add support for optional router configuration callback
dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings
dmaengine: ti: k3-udma-glue: Get the ringacc from udma_dev
dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API
dmaengine: ti: k3-udma: Add support for second resource range from sysfw
dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
...
These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead of
SoC specific code. This is the latest step in the ongoing process for
moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas.
There is one conflict in the dra7.dts file, which adds another node
in a different branch. Watch out for adding the trailing '};'
both times.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=0mXx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC OMAP GenPD updates from Arnd Bergmann:
"These are additional updates for the power domain support on OMAP,
moving to an implementation based on device tree information instead
of SoC specific code. This is the latest step in the ongoing process
for moving code out of arch/arm/mach-omap2.
I kept this separate from the other driver changes since it touches
code in multiple areas"
* tag 'arm-soc-omap-genpd-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits)
ARM: OMAP2+: Fix am4 only build after genpd changes
ARM: dts: Configure power domain for omap5 dss
ARM: dts: omap5: add remaining PRM instances
soc: ti: omap-prm: omap5: add genpd support for remaining PRM instances
ARM: OMAP2+: Drop legacy platform data for dra7 gpmc
ARM: dts: Configure interconnect target module for dra7 iva
ARM: dts: dra7: add remaining PRM instances
soc: ti: omap-prm: dra7: add genpd support for remaining PRM instances
clk: ti: dra7: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy platform data for omap4 gpmc
ARM: OMAP2+: Drop legacy platform data for omap4 iva
ARM: dts: Configure power domain for omap4 dsp
ARM: dts: Configure power domain for omap4 dss
ARM: dts: omap4: add remaining PRM instances
soc: ti: omap-prm: omap4: add genpd support for remaining PRM instances
clk: ti: omap4: Drop idlest polling from IVA clkctrl clocks
ARM: OMAP2+: Drop legacy remaining legacy platform data for am4
ARM: dts: Use simple-pm-bus for genpd for am4 l3
ARM: dts: Move am4 l3 noc to a separate node
ARM: dts: Use simple-pm-bus for genpd for am4 l4_per
...
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Pull i2c updates from Wolfram Sang:
"A bit smaller this time with mostly usual driver updates. Slave
support for imx stands out a little"
* 'i2c/for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (30 commits)
i2c: remove check that can never be true
i2c: Warn when device removing fails
dt-bindings: i2c: Update DT binding docs to support SiFive FU740 SoC
dt-bindings: i2c: Add compatible string for AM64 SoC
i2c: designware: Make register offsets all of the same width
i2c: designware: Switch header to use BIT() and GENMASK()
i2c: pxa: move to generic GPIO recovery
i2c: sh_mobile: Mark adapter suspended during suspend
i2c: owl: Add compatible for the Actions Semi S500 I2C controller
dt-bindings: i2c: owl: Convert Actions Semi Owl binding to a schema
i2c: imx: support slave mode for imx I2C driver
i2c: ismt: Adding support for I2C_SMBUS_BLOCK_PROC_CALL
i2c: ocores: Avoid false-positive error log message.
Revert "i2c: qcom-geni: Disable DMA processing on the Lenovo Yoga C630"
i2c: mxs: Remove unneeded platform_device_id
i2c: pca-platform: drop two members from driver data that are assigned to only
i2c: imx: Remove unused .id_table support
i2c: nvidia-gpu: drop empty stub for runtime pm
dt-bindings: i2c: mellanox,i2c-mlxbf: convert txt to YAML schema
i2c: mv64xxx: Add bus error recovery
...
Detailed description for this pull request:
1. Update devfreq core
- Add new devfreq_frequency tracepoint to show the frequency change
information.
- Add governor feature flag. The devfreq governor is able to
have the specific flag in order to contain the non-common feature.
For example, if governor contains the 'immutable' feature, don't allow
user to change the governor via sysfs.
- Add governor sysfs attribute flag for each sysfs file. Prior to that
devfreq subsystem show the all sysfs files regardless of governor type.
But, some sysfs fils are not supported on the specific devfreq governor.
In order to show the only supported sysfs files according to the governor,
clarify the access permission of sysfs attributes according to governor.
When adding the devfreq governor, can specify the available attribute
information by using DEVFREQ_GOV_ATTR_* constant variable. The user can
read or write the sysfs attributes in accordance to the specified attributes.
- Clean-up the code to remove the duplicate code for the devfreq tracepoint
and to remove redundant governor_name field from struct devfreq
2. Update exynos-bus.c devfreq driver
- Add interconnect API support for the Samsung Exynos Bus Frequency driver
of exynos-bus.c. Complementing the devfreq driver with an interconnect
functionality allows to ensure the QoS requirements of devices accessing
the system memory (e.g. video processing devices) are fulfilled
and allows to avoid issues like the DMA underrun.
3. Update tegra devfreq driver
- Add interconnect support and OPP interface for tegra30-devfreq.c.
Also, it is to guarantee the QoS requirement of some devices like
display controller.
- Move tegra20-devfreq.c from drivers/devfreq/ into driver/memory/tegra/
in order to use the more proper monitoring feature such as EMC_STAT
which is based in driver/memory/tegra/.
- Separate the configuration information for different SoC on
tegra30-devfrqe.c. The tegra30-devfreq.c had been supported both
tegra30-actmon and tegra124-actmon devices. In order to use
the more correct configuration data, separate them.
- Use dev_err_probe() to handle the deferred probe error on tegra30-devfreq.c.
4. Pull the request of 'Tegra SoC and clock controller changes for v5.11'
sent by Krzysztof Kozlowski <krzk@kernel.org> in order to prevent the
build error.
-----BEGIN PGP SIGNATURE-----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=t1gj
-----END PGP SIGNATURE-----
Merge tag 'devfreq-next-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq updates for 5.11 from Chanwoo Choi:
1. Update devfreq core
- Add new devfreq_frequency tracepoint to show the frequency change
information.
- Add governor feature flag. The devfreq governor is able to set the
specific flag in order to support a non-common feature. For
example, if the governor supports the 'immutable' feature, don't
allow user space to change the governor via sysfs.
- Add governor sysfs attribute flag for each sysfs file. Prior to that
the devfreq subsystem allowed all of the sysfs files to be accessed
regardless of the governor type. But some sysfs fils are not
supported by specific devfreq governors. In order to only allow the
sysfs files supported by the governor to be accessed, clarify the
access permissions of sysfs attributes according to the governor.
When adding the devfreq governor, specify the available attribute
information by using DEVFREQ_GOV_ATTR_* symbols. The user can read
or write the sysfs attributes in accordance to the specified
access permissions.
- Clean-up the code to reduce duplication for the devfreq tracepoint
and to remove redundant governor_name field from struct devfreq.
2. Update exynos-bus.c devfreq driver
- Add interconnect API support to the Samsung Exynos Bus Frequency
driver, exynos-bus.c. Complementing the devfreq driver with
interconnect functionality allows to ensure that the QoS
requirements regarding devices accessing the system memory (e.g.
video processing devices) will be met and allows to avoid issues
like DMA underrun.
3. Update tegra devfreq driver
- Add interconnect support and OPP interface to tegra30-devfreq.c.
Also, it is to guarantee the QoS requirement of some devices like
the display controller.
- Move tegra20-devfreq.c from drivers/devfreq/ into drivers/memory/tegra/
in order to use the more proper monitoring feature such as EMC_STAT
which is located in drivers/memory/tegra/.
- Separate the configuration information for different SoCs in
tegra30-devfrqe.c. The tegra30-devfreq.c had been supporting both
tegra30-actmon and tegra124-actmon devices. In order to use the
more correct configuration data, separate them.
- Use dev_err_probe() to handle the deferred probe error in
tegra30-devfreq.c.
4. Pull the request of 'Tegra SoC and clock controller changes for
v5.11' sent by Krzysztof Kozlowski <krzk@kernel.org> in order to
avoid a build error."
* tag 'devfreq-next-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: tegra30: Separate configurations per-SoC generation
PM / devfreq: tegra30: Support interconnect and OPPs from device-tree
PM / devfreq: tegra20: Deprecate in a favor of emc-stat based driver
PM / devfreq: exynos-bus: Add registration of interconnect child device
dt-bindings: devfreq: Add documentation for the interconnect properties
soc/tegra: fuse: Add stub for tegra_sku_info
soc/tegra: fuse: Export tegra_read_ram_code()
clk: tegra: Export Tegra20 EMC kernel symbols
PM / devfreq: tegra30: Silence deferred probe error
PM / devfreq: tegra20: Relax Kconfig dependency
PM / devfreq: tegra20: Silence deferred probe error
PM / devfreq: Remove redundant governor_name from struct devfreq
PM / devfreq: Add governor attribute flag for specifc sysfs nodes
PM / devfreq: Add governor feature flag
PM / devfreq: Add tracepoint for frequency changes
PM / devfreq: Unify frequency change to devfreq_update_target func
trace: events: devfreq: Use fixed indentation size to improve readability
The DMAs in AM64 have built in rings compared to AM654/J721e/J7200 where a
separate and generic ringacc is used.
The ring SW interface is similar to ringacc with some major architectural
differences, like
They are part of the DMA (BCDMA or PKTDMA).
They are dual mode rings are modeled as pair of Rings objects which has
common configuration and memory buffer, but separate real-time control
register sets for each direction mem2dev (forward) and dev2mem (reverse).
The ringacc driver must be initialized for DMA rings use with
k3_ringacc_dmarings_init() as it is not an independent device as ringacc
is.
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-17-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Because mtk-mmsys uses the 'devm_platform_ioremap_resource' function, it
should depend on HAS_IOMEM.
Fixes: cc6576029a ("soc: mediatek: mmsys: Use devm_platform_ioremap_resource()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20201203121447.3366406-1-enric.balletbo@collabora.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Mark PM functions of newly added clkout module as unused to silence
!CONFIG_PM warnings.
2. Initialize ChipID driver later - in arch initcall.
-----BEGIN PGP SIGNATURE-----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=VCRg
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/drivers
Samsung SoC drivers changes for v5.11, part two
1. Mark PM functions of newly added clkout module as unused to silence
!CONFIG_PM warnings.
2. Initialize ChipID driver later - in arch initcall.
* tag 'samsung-drivers-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
Link: https://lore.kernel.org/r/20201207074528.4475-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Switch the "logicoreip" registers to the new xlnx,vcu-settings binding
to be able to read the settings if the settings are specified in a
separate device tree node that is shared with other drivers.
If the driver is not able to find a node with the new binding, fall back
to check for the logicore register bank to be backwards compatible.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Link: https://lore.kernel.org/r/20201109134818.4159342-4-m.tretter@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The message that the driver was successfully probed only adds useless
noise. Drop the message.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Link: https://lore.kernel.org/r/20201109134818.4159342-2-m.tretter@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Minor fixes for the io-domain soc-driver
* tag 'v5.11-rockchip-drivers-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
soc: rockchip: io-domain: Remove incorrect and incomplete comment header
Link: https://lore.kernel.org/r/2045618.irdbgypaU6@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
soc: amlogic: driver updates for v5.11
- enable building as modules
- reset API updates
* tag 'amlogic-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
soc: amlogic: replace devm_reset_control_array_get()
soc: amlogic: canvas: add missing put_device() call in meson_canvas_get()
firmware: meson-sm: enable build as module
soc: meson: enable building drivers as modules
soc: amlogic: socinfo: build for specific arch
Link: https://lore.kernel.org/r/7him9ljgtr.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
drivers: soc: TI SOC changes for 5.11
- ti_sci changes towards DMSS support
- Static warning fixes
- Kconfig update for Keystone ARM64 socs
- AM64X SOC family support
* tag 'drivers_soc_for_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone: (23 commits)
drivers: soc: ti: knav_qmss_queue: Fix error return code in knav_queue_probe
soc: ti: Fix reference imbalance in knav_dma_probe
soc: ti: pruss: Remove wrong check against *get_match_data return value
soc: ti: Kconfig: Drop ARM64 SoC specific configs
soc: ti: k3-ringacc: Provide documentation for 'k3_ring's 'state'
soc: ti: wkup_m3_ipc: Document 'm3_ipc' parameter throughout
soc: ti: pm33xx: Remove set but unused variable 'ret'
soc: ti: knav_dma: Fix a kernel function doc formatting issue
soc: ti: knav_qmss_queue: Fix a whole host of function documentation issues
soc: ti: knav_qmss_queue: Remove set but unchecked variable 'ret'
soc: ti: omap-prm: Do not check rstst bit on deassert if already deasserted
soc: ti: knav_qmss: fix reference leak in knav_queue_probe
soc: ti: k3-socinfo: Add entry for AM64X SoC family
soc: ti: k3-ringacc: Use correct device for allocation in RING mode
firmware: ti_sci: rm: Remove unused config() from ti_sci_rm_ringacc_ops
soc: ti: k3-ringacc: Use the ti_sci set_cfg callback for ring configuration
firmware: ti_sci: rm: Add new ops for ring configuration
firmware: ti_sci: rm: Remove ring_get_config support
firmware: ti_sci: rm: Add support for extended_ch_type for tx channel
soc: ti: ti_sci_inta_msi: Add support for second range in resource ranges
...
Link: https://lore.kernel.org/r/1606851405-26338-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Driver changes for omaps for genpd for v5.11 merge window
This series of changes allows booting am335x with genpd and
device tree data without the legacy platform data. Also at
least am437x can be booted with gendp with power domain and
dts data. The SoC specific dts changes will be a separate
pull request.
We need the following driver changes merged before the dts
changes can be done:
- platform code needs a few improvments to probe l4_wkup first
for clocks, and to bail out when there is no platform data
- ti-sysc driver needs a non-urgent fix for asserting rstctrl
reset only after disabling the clocks, to probe modules with
no known control registers, and added quirk handling for gpmc
devices
- omap-prm driver needs a non-urgent fix for reset status bit,
support added for pm_clk, and then we add the rest of am335x
power domain data
- clock driver for am335x needs to keep l3_main clock enabled
with genpd for suspend and resume to work
- wkup_m3 remoteproc driver needs support added for reset
control if available instead of the legacy pdata callbacks
- pm33xx driver needs PM runtime support added for genpd
The am335x specific driver changes for the clock, wkup_m3,
pm33xx and remoteproc drivers are quite trivial and have not
caused merge conflicts in Linux next. I did not get acks for
these changes except from Santosh but had already pushed out
the branch already at that point. So I've added the related
driver maintainers to Cc.
* tag 'omap-for-v5.11/genpd-drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
remoteproc/wkup_m3: Use reset control driver if available
soc: ti: pm33xx: Enable basic PM runtime support for genpd
soc: ti: omap-prm: am3: add genpd support for remaining PRM instances
soc: ti: omap-prm: Add pm_clk for genpd
clk: ti: am33xx: Keep am3 l3 main clock always on for genpd
bus: ti-sysc: Implement GPMC debug quirk to drop platform data
bus: ti-sysc: Support modules without control registers
ARM: OMAP2+: Probe PRCM first to probe l4_wkup with simple-pm-bus
ARM: OMAP2+: Check for inited flag
bus: ti-sysc: Assert reset only after disabling clocks
soc: ti: omap-prm: Do not check rstst bit on deassert if already deasserted
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606806458-694517@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm driver updates for v5.11
This adds support for the core power domains on MSM8916, MSM8939, SDM660
and SDX55. It adds SM8150 support to the last-level cache controller
driver and it makes it possible to build the Command DB and RPMh drivers
as modules.
It also contains a slew of smaller cleanups, style and bug fixes
throughout the various drivers.
* tag 'qcom-drivers-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (39 commits)
soc: qcom: rpmhpd: Add SDX55 power domains
dt-bindings: power: Add rpm power domain bindings for sdx55
soc: qcom: rpmh: Use __fill_rpmh_msg API during rpmh_write()
samples: qmi: Constify static qmi ops
soc: qcom: pdr: Constify static qmi structs
soc: qcom: initialize local variable
soc: qcom: socinfo: add soc ids for msm8953 variants
soc: qcom: geni: Remove "iova" check
soc: qcom: llcc: Add configuration data for SM8150
dt-bindings: msm: Add LLCC for SM8150
soc: qcom: rpmh: Fix possible doc-rot in rpmh_write()'s header
soc: qcom: kryo-l2-accessors: Fix misnaming of 'val'
soc: qcom: rpmhpd: Provide some missing struct member descriptions
soc: qcom: llcc-qcom: Fix expected kernel-doc formatting
soc: qcom: smp2p: Remove unused struct attribute provide another
soc: qcom: wcnss_ctrl: Demote non-conformant struct header and fix function headers
soc: qcom: smsm: Fix some kernel-doc formatting and naming problems
soc: qcom: smem: Fix formatting and missing documentation issues
soc: qcom: qcom-geni-se: Fix misnamed function parameter 'rx_rfr'
soc: qcom: qcom_aoss: Add missing description for 'cooling_devs'
...
Link: https://lore.kernel.org/r/20201130190142.345246-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Exynos ChipID driver on Exynos SoCs has only informational
purpose - to expose the SoC device in sysfs. No other drivers
depend on it so there is really no benefit of initializing it early.
Instead, initialize everything with arch_initcall which:
1. Allows to use dev_info() as the SoC bus is present (since
core_initcall),
2. Could speed things up because of execution in a SMP environment
(after bringing up secondary CPUs, unlike early_initcall),
3. Reduces the amount of work to be done early, when the kernel has to
bring up critical devices.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201202195955.128633-2-krzk@kernel.org
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: e943c43b32 ("PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1607070805-33038-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
devm_reset_control_array_get_exclusive() looks more readable
Signed-off-by: Yejune Deng <yejune.deng@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/1605667700-16681-1-git-send-email-yejune.deng@gmail.com
if of_find_device_by_node() succeed, meson_canvas_get() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: 382f8be045 ("soc: amlogic: canvas: Fix meson_canvas_get when probe failed")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201117011322.522477-1-yukuai3@huawei.com
New drivers:
- SoC info driver to expose revision information
New features:
- AST2600 support for the LPC control driver. This includes
setting the LPC2AHB bridge up in a backwards compatible manner.
Cleanups:
- LPC control
- Kconfig
- Bindings updates for AST2600 strings
-----BEGIN PGP SIGNATURE-----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=KcaK
-----END PGP SIGNATURE-----
Merge tag 'aspeed-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into arm/drivers
ASPEED soc driver updates for 5.11
New drivers:
- SoC info driver to expose revision information
New features:
- AST2600 support for the LPC control driver. This includes
setting the LPC2AHB bridge up in a backwards compatible manner.
Cleanups:
- LPC control
- Kconfig
- Bindings updates for AST2600 strings
* tag 'aspeed-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
soc: aspeed: Enable drivers with ARCH_ASPEED
soc: aspeed: Fix a reference leak in aspeed_socinfo_init()
soc: aspeed: remove unneeded semicolon
soc: aspeed-lpc-ctrl: Fix driver name
soc: aspeed-lpc-ctrl: Fix whitespace
soc: aspeed-lpc-ctrl: LPC to AHB mapping on ast2600
soc: aspeed-lpc-ctrl: Fail probe of lpc-ctrl if reserved memory is not aligned
soc: aspeed: lpc: Add AST2600 compatible strings
dt-bindings: aspeed-lpc: Add AST2600 compatible strings
ARM: dts: aspeed: Add silicon id node
soc: aspeed: Add soc info driver
dt-bindings: aspeed: Add silicon id node to SCU
soc: aspeed: Improve kconfig
Link: https://lore.kernel.org/r/CACPK8Xe=9ezhyWRMqVOEQr7SU1YoYfVBGGdGzjmE4SiBr--vJQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add support for new power domain driver.
- add support for mt8183 and mt8192
devapc:
- add support for the devapc device found on mt6779 to identify of
malicious bus accesses from a controller to a device
mmsys:
- move DDP routing IDs into the driver
cmdq:
- drop timeout handler support as not usefull
scpsys:
- print warning on theoretical error
-----BEGIN PGP SIGNATURE-----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=mQNT
-----END PGP SIGNATURE-----
Merge tag 'v5.10-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
power-domains:
- add support for new power domain driver.
- add support for mt8183 and mt8192
devapc:
- add support for the devapc device found on mt6779 to identify of
malicious bus accesses from a controller to a device
mmsys:
- move DDP routing IDs into the driver
cmdq:
- drop timeout handler support as not usefull
scpsys:
- print warning on theoretical error
* tag 'v5.10-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (21 commits)
soc: mediatek: mmsys: Use devm_platform_ioremap_resource()
soc / drm: mediatek: Move DDP component defines into mtk-mmsys.h
soc: mediatek: add mt6779 devapc driver
dt-bindings: devapc: add bindings for mtk-devapc
soc / drm: mediatek: cmdq: Remove timeout handler in helper function
soc: mediatek: pm-domains: Add support for mt8192
soc: mediatek: pm-domains: Add default power off flag
soc: mediatek: pm-domains: Add support for mt8183
soc: mediatek: pm-domains: Allow bus protection to ignore clear ack
soc: mediatek: pm-domains: Add subsystem clocks
soc: mediatek: pm-domains: Add extra sram control
soc: mediatek: pm-domains: Add SMI block as bus protection block
soc: mediatek: pm_domains: Make bus protection generic
soc: mediatek: pm-domains: Add bus protection protocol
soc: mediatek: Add MediaTek SCPSYS power domains
dt-bindings: power: Add MT8192 power domains
dt-bindings: power: Add MT8183 power domains
dt-bindings: power: Add bindings for the Mediatek SCPSYS power domains controller
mfd: syscon: Add syscon_regmap_lookup_by_phandle_optional() function.
MAINTAINERS: change mediatek wiki page
...
Link: https://lore.kernel.org/r/b03fe343-e183-c6f3-f2dc-4c58aae3146b@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pull the following:
- Lee provides a missing function declaration spotted with W=1 builds
-----BEGIN PGP SIGNATURE-----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=c9m4
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.11/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoCs driver changes for 5.11, please
pull the following:
- Lee provides a missing function declaration spotted with W=1 builds
* tag 'arm-soc/for-5.11/drivers' of https://github.com/Broadcom/stblinux:
soc: bcm: brcmstb: pm: pm-arm: Provide prototype for brcmstb_pm_s3_finish()
Link: https://lore.kernel.org/r/20201128163410.1691529-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the common platform_get_resource()+devm_platform_ioremap() combination,
there is a helper, so use it and make the code a bit more compact.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20201006193320.405529-3-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MMSYS is the driver which controls the routing of these DDP components,
so the definition of the mtk_ddp_comp_id enum should be placed in mtk-mmsys.h
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20201006193320.405529-2-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MediaTek bus fabric provides TrustZone security support and data
protection to prevent slaves from being accessed by unexpected
masters.
The security violation is logged and sent to the processor for
further analysis or countermeasures.
Any occurrence of security violation would raise an interrupt, and
it will be handled by mtk-devapc driver. The violation
information is printed in order to find the murderer.
Signed-off-by: Neal Liu <neal.liu@mediatek.com>
Link: https://lore.kernel.org/r/1602732039-12179-3-git-send-email-neal.liu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
For each client driver, its timeout handler need to dump hardware register
or its state machine information, and their way to detect timeout are
also different, so remove timeout handler in helper function and
let client driver implement its own timeout handler.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20201102000438.29225-1-chunkuang.hu@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+fOigeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGoQ0H/RLJU2FMIjO0mzLX
9LqePQ9QmNWG4KeqxwWaKq90MinIbnSG3CDPKruu8RNh2Rr6nsEJmqg1DWyEiFRB
8gzsBXMAC1i2aPfOrOnCJEfP+L+svKlbSii475tNdZw2DhP+/FBT0RVCt3rRhrRs
atc8+dM7ViGLnlvRJ4LlVqA3d1kjOr5bsPYcIcnGIHY8mYWBLFzTSVgDdrcB9+3l
7lZud/zMhJ3dS0bcnbIUS1YpBxHCsgEaMFQYmcv3RruIaaFbh5THkfQUSmbmrAru
/EeVjwVMuvpvb2jxS1ofLx2in7t4tsNgItu4AfMmV0BurM5NhpqKo7mo/1nmR/X9
Q4tjPRc=
=cUbb
-----END PGP SIGNATURE-----
Backmerge tag 'v5.10-rc2' into arm/drivers
The SCMI pull request for the arm/drivers branch requires v5.10-rc2
because of dependencies with other git trees, so merge that in here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a couple of warning fixes and a fix for a mostly harmless
bug in the process ID retrieval code.
-----BEGIN PGP SIGNATURE-----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=mYgF
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.11-rc1
This contains a couple of warning fixes and a fix for a mostly harmless
bug in the process ID retrieval code.
* tag 'tegra-for-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: Fix index bug in get_process_id
soc: tegra: fuse: speedo-tegra210: Remove a group of set but unused variables
soc: tegra: fuse: speedo-tegra124: Remove some set but unused variables
Link: https://lore.kernel.org/r/20201127144329.124891-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There is no reason to keep on using the __raw_{read,write}l() I/O
accessors in Renesas ARM driver code. Switch to using the plain
{read,write}l() I/O accessors, to have a chance that this works on
big-endian.
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201119125214.4065925-1-geert+renesas@glider.be
Add the needed board data to support mt8192 SoC.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Weiyi Lu <weiyi.lu@mediatek.com>
Link: https://lore.kernel.org/r/20201030113622.201188-17-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
For some power domain, like conn on MT8192, it should be default OFF.
Because the power on/off control relies the function of connectivity chip
and its firmware. And if project choose other chip vendor solution,
those necessary connectivity functions will not provided.
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20201030113622.201188-16-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Linus Torvalds