This function frees resources and cancels delayed work item that
have been initialized in fec_ptp_init().
Use this to do proper error handling if something goes wrong in
probe function after fec_ptp_init has been called.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.
Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.
To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet. ENET IP supports sleep mode
in low power status, when system enter suspend status, Magic packet can
wake up system even if all SOC clocks are gate. The patch doing below things:
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- add standard ethtool WOL interface
- enable the ENET interrupt to wake us
Tested on i.MX6q/dl sabresd, sabreauto boards, i.MX6SX arm2 boards.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timecounter code has almost nothing to do with the clocksource
code. Let it live in its own file. This will help isolate the
timecounter users from the clocksource users in the source tree.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX fec support three rx ring1, the current driver lost to init
ring1 and ring2 maximum receive buffer size, that cause receving
frame date length error. The driver reports "rcv is not +last" error
log in user case.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fep->bufdesc_ex is treated as a boolean value, thus declare it as
such.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.
ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;
For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.
Changes V2:
Modify the commit/comments log to describe the issue clearly.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC ptp timer has 4 channel compare/trigger function. It can be used to
enable pps output.
The pulse would be ouput high exactly on N second. The pulse ouput high
on compare event mode is used to produce pulse per second. The pulse
width would be one cycle based on ptp timer clock source.Since 31-bit
ptp hardware timer is used, the timer will wrap more than 2 seconds. We
need to reload the compare compare event about every 1 second.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC IP supports hardware adjustment for ptp timer. Refer to the description of
ENET_ATCOR and ENET_ATINC registers in the spec about the hardware adjustment. This
patch uses hardware support to adjust the ptp offset and frequency on the slave side.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <b38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Copy short frames and keep the buffers mapped, re-allocate skb instead of
memory copy for long frames.
- Add support for setting/getting rx_copybreak using generic ethtool tunable
Changes V3:
* As Eric Dumazet's suggestion that removing the copybreak module parameter
and only keep the ethtool API support for rx_copybreak.
Changes V2:
* Implements rx_copybreak
* Rx_copybreak provides module parameter to change this value
* Add tunable_ops support for rx_copybreak
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver loss Ftype field init for BD, which cause tx
queue #1 and #2 cannot work well.
Add Ftype field to BD to distiguish three queues for AVB:
0 -> Best Effort
1 -> ClassA
2 -> ClassB
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when enable interrupt coalesce, 8 BD is not enough.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX support interrupt coalescence feature
By default, init the interrupt coalescing frame count threshold and
timer threshold.
Supply the ethtool interfaces as below for user tuning to improve
enet performance:
rx_max_coalesced_frames
rx_coalesce_usecs
tx_max_coalesced_frames
tx_coalesce_usecs
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues.
For tx queues: ring 0 -> best effort
ring 1 -> Class A
ring 2 -> Class B
For rx queues:
ring 0 -> best effort
ring 1 -> receive VLAN packet with classification match
ring 2 -> receive VLAN packet with classification match
Add enet-avb IP multiqueue support for the driver.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
fsl,num-tx-queues=<3>;
fsl,num-rx-queues=<3>
Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just change data structure to support multi-queue.
Only 1 queue enabled.
Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdf
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
For imx6sx, it alos is the clock source of interrupt coalescing.
The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
the refrence clock is 125Mhz coming from internal PLL or external.
In i.MX6sx-arm2 board, the clock is from internal PLL.
clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.
The patch add clk_ref to distiguish the different clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.
FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.
To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.
i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.
To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for specifying the phy to be used with the fec in the
devicetree using the standard phy-handle property and also supports
fixed-link.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.
Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.
Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.
Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add software TSO support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board, running iperf tcp tests shows:
- 16.2% improvement comparing with FEC SG patch
- 82% improvement comparing with NO SG & TSO patch
$ ethtool -K eth0 tso on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 35388 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 181 MBytes 506 Mbits/sec
During the testing, CPU loading is 30%.
Since imx6dl FEC Bandwidth is limited to SOC system bus bandwidth, the
performance with SW TSO is a milestone.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Scatter/gather support for FEC.
This feature allows to improve outbound throughput performance.
Tested on imx6dl sabresd board:
Running iperf tests shows a 55.4% improvement.
$ ethtool -K eth0 sg off
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52618 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 99.5 MBytes 278 Mbits/sec
$ ethtool -K eth0 sg on
$ iperf -c 10.192.242.167 -t 3 &
[ 3] local 10.192.242.108 port 52617 connected with 10.192.242.167 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 154 MBytes 432 Mbits/sec
CC: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support SG, software TSO, let's increase BD entry number.
CC: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable and easy to support other features like
SG, TSO, moving the common transmit function to one api.
And the patch also factorize the getting BD index to it own function.
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: error to get the previous BD entry. When the current BD
is the first BD, the previous BD entry must be the last BD,
not "bdp - 1" in current logic.
V4:
* Optimize fec_enet_get_nextdesc() for code clean.
Replace "ex_new_bd - ring_size" with "ex_base".
Replace "new_bd - ring_size" with "base".
V3:
* Restore the API name because David suggest to use fec_enet_
prefix for all function in fec driver.
So, change next_bd() -> fec_enet_get_nextdesc()
change pre_bd() -> fec_enet_get_prevdesc()
* Reduce the two APIs parameters for easy to call.
V2:
* Add tx_ring_size and rx_ring_size to struct fec_enet_private.
* Replace api fec_enet_get_nextdesc() with next_bd().
Replace api fec_enet_get_prevdesc() with pre_bd().
* Move all ring size check logic to next_bd() and pre_bd(), which
simplifies the code redundancy.
V1:
* Add BD ring size check to get the previous BD entry in correctly.
Reviewed-by: Li Frank <B20596@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Frank Li <frank.li@freescale.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool operation to read RMON registers.
Tested against net-next on i.MX28.
v2: make conditional on #ifndef CONFIG_M5272
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing pdev in fec_ptp_init() is enough, since we can get ndev locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a local reg_phy structure, let's put it inside the private
structure, so that we are able to have access to the regulator structure even
when we are outside fec_probe().
This is in preparation for controlling the FEC PHY regulator in the suspend and
resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;
You can see oops in one hour.
The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
Enables hardware generation of IP header and
protocol specific checksums for transmitted
packets.
Enabled hardware discarding of received packets with
invalid IP header or protocol specific checksums.
The feature is enabled by default but can be
enabled/disabled by ethtool.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MX28 boards need the internal enet_out clock to be enabled. So, do
this in the driver iff the clock was referenced via devicetree.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: David S. Miller <davem@davemloft.net>
Proviously we would only restart the FEC when PHY link or duplex state
changed. PHY does not always bring down the link for speed changes, in
which case we would not detect any change and keep FEC running.
Switching link speed without restarting the FEC results in the FEC being
stuck in an indefinite state, generating error conditions for every
packet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
build error cause by
Commit ff43da86c6
("NET: FEC: dynamtic check DMA desc buff type")
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_nextdesc’:
drivers/net/ethernet/freescale/fec.c:215:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_get_prevdesc’:
drivers/net/ethernet/freescale/fec.c:224:18: error: invalid use of undefined type ‘struct bufdesc_ex’
drivers/net/ethernet/freescale/fec.c: In function ‘fec_enet_start_xmit’:
drivers/net/ethernet/freescale/fec.c:286:37: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:287:13: error: arithmetic on pointer to an incomplete type
drivers/net/ethernet/freescale/fec.c:324:7: error: dereferencing pointer to incomplete type etc....
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lucas Stach