altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime. Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Altera TSE MAC rx DMA transfer starts with the 2 additional bytes for IP
payload alignment. This patch fixes tse_rx() function loop which reads DMA
rx status and extracts packet length from it. Status signalises a whole DMA
transfer length, which is 2 bytes longer than the packet itself.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for fixed-links in configurations without PHY.
(e.g. connection to a switch, SGMII point to point, SFPs)
Check: Documentation/devicetree/bindings/net/fixed-link.txt.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves false errors from MSGDMA in TX mSGDMA MM to ST
mode, and is a continuation of the patch recently submitted by Andrea
Oetken. The MSGDMA had a logic bug that masked detection of this issue
prior to Quartus 14.1/Build 164. When the MSGDMA logic bug was addressed
in Quartus 14.1/Build 164, the driver problem was exposed.
The problem is corrected by making sure MSGDMA_DESC_CTL_TR_ERR_IRQ is not
set for any of the transmit DMA descriptors, and only used for receive
descriptors.
Fixes: 71cd26e altera tse: Error-Bit on tx-avalon-stream always set.
Signed-off-by: Chee Nouk Phoon <cnphoon@altera.com>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>a
Cc: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Error-Bit on the avalon streaming interface of the
tx-dma-channel was always set. In SGMII configurations
this leads to error-symbols on the PCS and packet-rejection
on the receiver side (e.g. SGMII/1000Base-X connected switch).
This only applies to the tse-configuration with MSGDMA.
This issue was detected and fixed on a custom board with
a direct connection to a Marvell switch in SGMII-PHY-Mode.
(incl. custom patches for SGMII-PCS).
According to the datasheet if ff_tx_err (avalon-streaming)
is set it is forwarded to gm_tx_err. As a result the PCS
is forwarding the error by sending a "/V/"-caracter.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bug which occurs when more than <limit> packets are available during
napi-poll, leading to "delays" and retransmissions on the network.
Check for (count < limit) before checking the get_rx_status in tse_rx-function.
Function get_rx_status is reading from the response-fifo.
If there is currently a response in the fifo,
reading the last byte of the response pops the value from the fifo.
If the limit is checked as second condition
and the limit is reached the fifo is popped but the packet is not processed.
Signed-off-by: Andreas Oetken <ennoerlangen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorrect NAPI polling caused WARNING at net/core/dev.c net_rx_action.
Some stability issues were also seen at high throughput and system
load before this patch.
This patch contains several changes in altera_tse_main.c:
- tse_rx() is fixed to not process more than `limit` frames
- tse_poll() is refactored to match NAPI logic
- only received frames are counted for return value
- removed bogus condition `(rxcomplete >= budget || txcomplete > 0)`
- replace by: if (rxcomplete < budget) -> call __napi_complete and enable irq
- altera_isr()
- replace spin_lock_irqsave() by spin_lock() - we are in isr
- use spinlocks just over irq manipulation, not over __napi_schedule
- reset IRQ first, then disable and schedule napi
This is a cleaned up resubmission from Vlastimil's recent submission.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Roman Pisl <rpisl@kky.zcu.cz>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a typo in the way tx_fifo_depth is read from the
devicetree. This patch was submitted by Vlastimil about a week ago,
and is now cleaned up and resubmitted.
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This debug output is not really an error message since mac reset can fail
if the phy clocks are gated, specifically when the phy has been placed in
a powered down or isolation mode. The netdev output masks were changed from
err to dbg, and comments added in the code.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change use of Altera TSE's MDIO access from phy 0 registers to phy 1
registers. This allows support for GMII, MII, RGMII, and SGMII
designs where the external PHY is always accesible through
Altera TSE's MDIO phy 1 registers and Altera's PCS is accessible
through MDIO phy 0 registers for SGMII applications.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Tested-by: Kai Lin Ng <kailng@altera.com>
Tested-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Altera network device doesn't come up after
ifconfig eth0 down
ifconfig eth0 up
The reason behind is clearing priv->phydev during tse_shutdown().
The phydev is not restored back at tse_open().
Resubmiting as to follow Tobias Klauser suggestion.
phy_start/phy_stop are called on each ifup/ifdown and
phy_disconnect is called once during the module removal.
Signed-off-by: Kostya Belezko <bkostya@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids PHY and MDIO probing if no PHY chip is present.
This is the case mainly in optical links where there is no need for
PHY chip, and therefore no need of MDIO. In this scenario Ethernet
MAC is directly connected to an optical module through an external
SFP transceiver.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move PHY get addr and MDIO create to a new function to improve readability
and make it easier to avoid its usage. This will be useful for example in
the case where there is no PHY chip.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b26 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb3 ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables multicast hash filtering if present in the hardware
and uses promiscuous mode instead until the problem with multicast
filtering has been debugged, integrated and tested.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the many sparse errors and warnings contained in the
initial submission of the Altera Triple Speed Ethernet driver, and a
few minor cppcheck warnings. Changes are tested on ARM and NIOS2
example designs, and compile tested against multiple architectures.
Typical issues addressed were as follows:
altera_tse_ethtool.c:136:19: warning: incorrect type in argument
1 (different address spaces)
altera_tse_ethtool.c:136:19: expected void const volatile
[noderef] <asn:2>*addr
altera_tse_ethtool.c:136:19: got unsigned int *<noident>
...
altera_sgdma.c:129:31: warning: cast removes address space of
expression
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warnings:
drivers/net/ethernet/altera/altera_msgdma.c:23:5: warning: symbol 'msgdma_initialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:28:6: warning: symbol 'msgdma_uninitialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:32:6: warning: symbol 'msgdma_reset' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:77:6: warning: symbol 'msgdma_disable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:83:6: warning: symbol 'msgdma_enable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:89:6: warning: symbol 'msgdma_disable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:95:6: warning: symbol 'msgdma_enable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:101:6: warning: symbol 'msgdma_clear_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:107:6: warning: symbol 'msgdma_clear_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:114:5: warning: symbol 'msgdma_tx_buffer' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:129:5: warning: symbol 'msgdma_tx_completions' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:154:5: warning: symbol 'msgdma_add_rx_desc' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:181:5: warning: symbol 'msgdma_rx_status' was not declared. Should it be static?
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sgdma_descrip is a function name as well as the name of a struct. In
sgdma_initialize(), we should initialize the descriptor length field
with the actual length of a descriptor not with the size of the
function. In order to prevent such things from happening in the future,
rename the function to sgdma_setup_descrip().
Found by sparse which yields the following warning:
drivers/net/ethernet/altera/altera_sgdma.c:74:30: warning: expression using sizeof on a function
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the name used by Ethtool to something more
conventional in preparation for TSE Ethtool register dump
support to be added in the near future.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.
Abbreviated panic stack seen is as follows:
(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch initializes the pause quanta set for transmitted pause frames
to the IEEE specified default of 0xffff.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch works around a recently discovered unaligned receive dma problem
with the Altera SGMDA. The Altera SGDMA component cannot be configured to
DMA data to unaligned addresses for receive packet operations from the
Triple Speed Ethernet component because of a potential data transfer
corruption that can occur. This patch addresses this issue by
utilizing the shift 16 bits feature of the Altera Triple Speed Ethernet
component and modifying the receive buffer physical addresses accordingly
such that the target receive DMA address is always aligned on a 32-bit
boundary.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Tested-by: Matthew Gerlach <mgerlach@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses two typos in the original driver submission. One derived
from a cut & paste error, and another is a misspelling.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a portable pointer arithmetic issue in the
original submission found by the kbuild test robot.
config: make ARCH=i386 allyesconfig
altera_sgdma.c: In function 'sgdma_txphysaddr':
>> altera_sgdma.c:393:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:394:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->tx_dma_desc);
^
altera_sgdma.c: In function 'sgdma_rxphysaddr':
>> altera_sgdma.c:403:33: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
dma_addr_t offs = (dma_addr_t)((dma_addr_t)desc -
^
>> altera_sgdma.c:404:5: warning: cast from
>> pointer to integer of different size [-Wpointer-to-int-cast]
(dma_addr_t)priv->rx_dma_desc);
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the version number returned by the driver's get regs routine
invoked by ethtool so formatting can be dependent on the version
number returned, and any interesting formatted output can check
the version number for specific types of register data returned.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Altera Triple Speed Ethernet Makfile and
Kconfig file.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the main driver and header file for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds miscellaneous files for the Altera Ethernet Driver,
including ethtool support.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the SGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the MSGDMA soft IP support for the Altera Triple
Speed Ethernet driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobias Klauser