Rocker driver tracks arp_tbl neighs to resolve IPv4 route nexthops. The
driver uses NETEVENT_NEIGH_UPDATE for neigh adds and updates, but there is
no event when the neigh is removed from the device (such as when the device
goes admin down). This patches hooks ndo_neigh_destroy so the driver can
know when a neigh is removed from the device. In response, the driver will
purge the neigh entry from its internal tbl.
I didn't find an in-tree users of ndo_neigh_destroy, so I'm not sure if
this ndo is vestigial or if there are out-of-tree users. In any case, it
does what I need here. An alternative design would be to generate
NETEVENT_NEIGH_UPDATE event when neigh is being destroyed, setting state to
NUD_NONE so driver knows neigh entry is dead.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sucessful probe, driver prints the switch ID. This patch changes the
format of the printed ID to match what's used in sysfs phys_switch_id node.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACPI bindings for the smsc911x driver. Convert the DT specific calls
to nonspecific device* calls, This allows the driver to work
with both ACPI and DT configurations. Ethernet should now work when using
ACPI on ARM Juno.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.
[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to use the IS_ERR_VALUE() macro for checking
the return value from pm_runtime_* functions.
Just do a simple negative test instead.
The semantic patch that makes this change is available
in scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debugfs support to dump tid info like stid, sftid, tids, atid and
hwtids
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T4 adapter, offloaded servers tid for IPv4 connections are
allocated from filter region. So add a new field for server filter tid if
server tid is allocated from filter region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the tid info, differentiate from which region the TID is allocated
from. It can be from TCAM region or HASH region.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding more details to sge qinfo for debugging purpose.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This BQL implementation is mostly derived from its related driver, alx.
Tested on AR8131 (rev c0) [1969:1063]. Saturated a 100mbps link with 5
concurrent runs of netperf. Ping latency dropped from 14ms to 3ms.
Signed-off-by: Ron Angeles <ronangeles@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current filer rule optimization is broken in several ways:
(1) Can perform reads/writes beyond end of allocated tables.
(gianfar_ethtool.c:1326).
(2) It breaks badly for rules with more than 2 specifiers
(e.g. matching ip, port, tos).
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 tos 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 tos 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 tos 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: TOS == 00000003 AND Q:00 ctrl:0000008a prop:00000003
05: DIA == 0a000003 AND Q:11 ctrl:0000448c prop:0a000003
06: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
07: TOS == 00000002 AND Q:00 ctrl:0000008a prop:00000002
08: DIA == 0a000002 AND Q:09 ctrl:0000248c prop:0a000002
09: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
0a: DPT == 00000001 AND Q:00 ctrl:0000008e prop:00000001
0b: TOS == 00000001 CLE Q:01 ctrl:0000060a prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
(Entire cluster gets AND-ed together).
(3) We observed that the masking rules it generates do not
play well with clustering on P2020. Only first rule
of the cluster would ever fire. Given that optimizer
relies heavily on masking this is very hard to fix.
Example:
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.1 dst-port 1 action 1
Added rule with ID 254
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.2 dst-port 2 action 9
Added rule with ID 253
# ethtool -N eth2 flow-type udp4 dst-ip 10.0.0.3 dst-port 3 action 17
Added rule with ID 252
# ./filer_decode /sys/kernel/debug/gfar1/filer_raw
00: MASK == 00000210 AND Q:00 ctrl:00000080 prop:00000210
01: FPR == 00000210 AND CLE Q:00 ctrl:00000281 prop:00000210
02: MASK == ffffffff AND Q:00 ctrl:00000080 prop:ffffffff
03: DPT == 00000003 AND Q:00 ctrl:0000008e prop:00000003
04: DIA == 0a000003 Q:11 ctrl:0000440c prop:0a000003
05: DPT == 00000002 AND Q:00 ctrl:0000008e prop:00000002
06: DIA == 0a000002 Q:09 ctrl:0000240c prop:0a000002
07: DIA == 0a000001 AND Q:00 ctrl:0000008c prop:0a000001
08: DPT == 00000001 CLE Q:01 ctrl:0000060e prop:00000001
ff: MASK >= 00000000 Q:00 ctrl:00000020 prop:00000000
Which looks correct according to the spec but only the first
(eth id 252)/last added rule for 10.0.0.3 will ever trigger.
As if filer did not treat the AND CLE as cluster start but
also kept AND-ing the rules. We found no errata covering this.
The fact that nobody noticed (2) or (3) makes me think
that this feature is not very widely used and we should just
remove it.
Reported-by: Aleksander Dutkowski <adutkowski@gmail.com>
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Acked-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At a cost of one line let's make sure .count is correct
when calling gfar_process_filer_changes().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAX_FILER_IDX is the last usable index. Using less-than
will already guarantee that one entry for catch-all rule
will be left, no need to subtract 1 here.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime. Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames.
Unlike SCC and FCC, the FEC doesn't handle the I bit in buffer
descriptors, instead it defines two interrupt bits, TXB and TXF.
We have to mask TXB in order to only get interrupts once the
frame is fully transmitted.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are not interested in interrupts for partially transmitted frames,
we have to clear BD_ENET_TX_INTR explicitly otherwise it may remain
from a previously used descriptor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an ndm_state member to the switchdev_obj_fdb structure,
in order to support static FDB addresses.
Set Rocker ndm_state to NUD_REACHABLE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way to get the MAC address in a firmware
independent manner, so set the MAC address of the device directly from
the ACPI tables.
The binding agrees with the proposed standard here:
http://www.uefi.org/sites/default/files/resources/nic-request-v2.pdf
Based on code from: Narinder Dhillon <ndhillon@cavium.com>
Tomasz Nowicki <tomasz.nowicki@linaro.org>
Robert Richter <rrichter@cavium.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate DT code in preparation for follow-on ACPI integration.
Based on code from: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use '%zx' to print size_t format in order to fix the following build warning:
drivers/net/ethernet/mellanox/mlxsw/item.h:65:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 6 has type 'size_t' [-Wformat=]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Writing each 4Kb page into flash might take up-to ~100 miliseconds,
during which time management firmware cannot acces the nvram for its
own uses.
Firmware upgrade utility use the ethtool API to burn new flash images
for the device via the ethtool API, doing so by writing several page-worth
of data on each command. Such action might create problems for the
management firmware, as the nvram might not be accessible for a long time.
This patch changes the write implementation, releasing the nvram lock on
the completion of each page, allowing the management firmware time to
claim it and perform its own required actions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On error flows its possible to free an SKB even if it was not allocated.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some tabs so that statements line up correctly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were missing curly braces so it means we call add_debugfs_mem()
unintentionally.
Fixes: 3ccc6cf74d ('cxgb4: Adds support for T6 adapter')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.
With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include local headers files after kernel's header files.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
cpu 0 cpu 1
fec_enet_txq_submit_skb
reserve a bdp for the first fragment
fec_enet_txq_submit_frag_skb
update the bdp for the other fragment
update txq->cur_tx
fec_enet_tx_queue
bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
This bdp is the bdp reserved for the first segment. Given
that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
is already pointed to a bdp beyond this one. We think this is a
completed bdp and try to reclaim it.
update the bdp for the first segment
update txq->cur_tx
So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit "e29aa33 bna: Enable Multi Buffer RX" moved packets counter
increment from the beginning of the NAPI processing loop after the check
for erroneous packets so they are never accounted. This counter is used
to inform firmware about number of processed completions (packets).
As these packets are never acked the firmware fires IRQs for them again
and again.
Fixes: e29aa33 ("bna: Enable Multi Buffer RX")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PP2 controller is capable of per-CPU TX processing, which means there are
per-CPU banked register sets and queues. Current version of the driver supports
TX packet coalescing - once on given CPU sent packets amount reaches a threshold
value, an IRQ occurs. However, there is a single interrupt line responsible for
CPU0/1 TX and RX events (the latter is not per-CPU, the hardware does not
support RSS).
When the top-half executes the interrupt cause is not known. This is why in
NAPI poll function, along with RX processing, IRQ cause register on both
CPU's is accessed in order to determine on which of them the TX coalescing
threshold might have been reached. Thus the egress processing and releasing the
buffers is able to take place on the corresponding CPU. Hitherto approach lead
to an illegal usage of on_each_cpu function in softirq context.
The problem is solved by resigning from TX coalescing interrupts and separating
egress finalization from NAPI processing. For that purpose a method of using
hrtimer is introduced. In main transmit function (mvpp2_tx) buffers are released
once a software coalescing threshold is reached. In case not all the data is
processed a timer is set on this CPU - in its interrupt context a tasklet is
scheduled in which all queues are processed. At once only one timer per-CPU can
be running, which is controlled by a dedicated flag.
This commit removes TX processing from NAPI polling function, disables hardware
coalescing and enables hrtimer with tasklet, using new per-CPU port structure
(mvpp2_port_pcpu).
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvpp2 driver allows usage of per-CPU TX processing. Once the packets are
prepared independetly on each CPU, the hardware enqueues the descriptors in
common TX queue. After they are sent, the buffers and associated sk_buffs
should be released on the corresponding CPU.
This is why a special index is maintained in order to point to the right data to
be released after transmission takes place. Each per-CPU TX queue comprise an
array of sent sk_buffs, freed in mvpp2_txq_bufs_free function. However, the
index was used there also for obtaining a descriptor (and therefore a buffer to
be DMA-unmapped) from common TX queue, which was wrong, because it was not
referring to the current CPU.
This commit enables proper unmapping of sent data buffers by indexing them in
per-CPU queues using a dedicated array for keeping their physical addresses.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using spinlocks protection during one-time driver initialization is not
necessary. Moreover it resulted in invalid GFP_KERNEL allocation under the lock.
This commit removes redundant spinlocks from buffer manager part of mvpp2
initialization.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reported-by: Alexandre Fournier <alexandre.fournier@wisp-e.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use the length of the transmitted skb (which was freed), but
that of the response skb.
This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.
Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCS of incoming packets is already checked by HW. Just strip it out.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This resolves compile errors on um-allyesconfig.
Note that there are many other drivers which have the same issue.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.
Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address in the switchdev_obj_fdb structure is currently represented
as a pointer. Replacing it for a 6-byte array allows switchdev to carry
addresses directly read from hardware registers, not stored by the
switch chip driver (as in Rocker).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
failed to configure the page size for architectures with page size
different than 4K.
Fixes: 938fe83 ("net/mlx5_core: New device capabilities handling")
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are paths in the driver such as an unrecoverable error (UE) detection
followed by a driver unload wherein be_clear() is invoked twice.
Individual data structures are reset so that they are not cleaned/freed
twice. This patch does the same for eqo->affinity_mask. It is freed only
if EQs haven't yet been destroyed. This fixes a possible crash when
affinity_mask is freed twice.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An RX stall issue was seen on Lancer adapters, when RXQs are destroyed
while they are in an "out of buffer" state. This patch fixes this issue
by posting 64 buffers to each RXQ before destroying them in the close path.
This is done after ensuring that no more new packets are selected for
transfer to the RXQs by disabling interface filters.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW issues were observed on Lancer adapters if IFACE filters
(flags, mac addrs etc) are enabled *before* creating RXQs. This patch
changes the driver design by enabling filters in be_open() --
instead of be_setup() -- after RXQs are created and buffers posted.
Two new wrapper functions, be_enable_if_filters() and
be_disable_if_filters() are introduced to enable/disable IFACE filters in
be_open()/be_close() respectively. In be_setup() the IFACE is now created
only with the RSS flag.
Signed-off-by: Kalesh AP <kalesh.purayil@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-08-05
This series contains updates to i40e, i40evf and e1000e.
Anjali adds support for x772 devices to i40e and i40evf. With the added
support, x772 supports offloading of the outer UDP transmit and receive
checksum for tunneled packets. Also supports evicting ATR filters in the
hardware, so update the driver with this new feature set.
Raanan provides several fixes for e1000e, first rectifies the Energy
Efficient Ethernet in Sx code so that it only applies to parts that
actually support EEE in Sx. Fix whitespace and moved ICH8 related define
to the proper context. Fixed the ASPM locking which was reported by
Bjorn Helgaas. Fix a workaround implementation for systime which could
experience a large non-linear increment of the systime value when
checking for overflow.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman