This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The array channel_all can be make static const rather than populating
it on the stack, this makes the code smaller. Also, variable place
is being initialized with a value that is never read, so this assignment
is redundant and can be removed.
Before:
text data bss dec hex filename
118537 9591 0 128128 1f480 realtek/rtlwifi/rtl8821ae/phy.o
After:
text data bss dec hex filename
118331 9687 0 128018 1f412 realtek/rtlwifi/rtl8821ae/phy.o
Saves 110 bytes, (gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: 610247f46f ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open(), single_release() should be used instead
of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSI interrupt should be enabled on certain platform.
Add a module parameter disable_msi to disable MSI interrupt,
driver will then use legacy interrupt instead.
One could rebind the PCI device, probe() will pick up the
new value of the module parameter. Such as:
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/unbind
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/bind
Tested-by: Ján Veselý <jano.vesely@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a mass of jobs between spin lock and unlock in the hardware
IRQ which will occupy much time originally. To make system work more
efficiently, this patch moves the jobs to the soft IRQ (bottom half) to
reduce the time in hardware IRQ.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer debugfs_topdir is initialized to a value that is never read
and it is re-assigned later. The initialization is redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
0day reports:
sparse warnings:
drivers/net/wireless/realtek/rtw88/coex.c:2457:6: sparse:
symbol 'rtw_coex_coex_dm_reset' was not declared. Should it be static?
rtw_coex_coex_dm_reset() is not called. Remove it.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WARN_ON() macro takes a condition, not a warning message. I've
changed this to use WARN() instead.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set
descriptor"), all the routines that get fields from a descriptor were
changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the TX and RX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of variables are initialized when declared that set later in the
routine, thus the initialization can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the call to hw_init() fails for any of the drivers, the driver will
leak memory that was allocated in BT coexistence setup. Technically, each
of the drivers should have done this free; however placing it in rtl_pci
fixes all the drivers with only a single patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtlwifi/efuse.c:16:31:
warning: RTL8712_SDIO_EFUSE_TABLE defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/efuse.c:9:17:
warning: MAX_PGPKT_SIZE defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the process of converting the bit manipulation macros were converted
to use GENMASK(), the compiler reported a value too big for the field.
The offending statement was trying to write 0x100 into a 5-bit field.
An accompaning comment says to set bit 3, thus the code is changed
appropriately.
This error has been in the driver since its initial submission.
Fixes: 29d00a3e46 ("rtlwifi: rtl8192cu: Add routine trx")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spurious warning message when building with W=1:
CC [M] drivers/net/wireless/realtek/rtlwifi/usb.o
drivers/net/wireless/realtek/rtlwifi/usb.c:243: warning: Cannot understand * on line 243 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:760: warning: Cannot understand * on line 760 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:790: warning: Cannot understand * on line 790 - I thought it was a doc line
Clean up the comment format.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Both RTL8822BE/RTL8822CE are WiFi + BT combo chips. Since
WiFi and BT use 2.4GHz to transmit, it is important to
make sure they run concurrently without interfering each
other. To achieve this, WiFi driver requires a mechanism
to collaborate with BT, whether they share the antenna(s)
or not.
The final decision made by the co-existence mechanism is
to choose a proper strategy, or called "tdma/table", and
inform either firmware or hardware of the strategy.
To choose a strategy, co-existence mechanism needs to
have enough information from WiFi and BT.
BT information is provided through firmware C2H.
The contents describe the current status of BT, such as
if BT is connected or is idle, or the profile that is
being used.
WiFi information can be provided by WiFi itself. The WiFi
driver will call various of "notify" functions each time
the state of WiFi changed, such as WiFi is going to switch
channel or is connected. Also WiFi driver can know if it
shares antenna with BT by reading efuse content. Antenna
configuration of the module will finally get a different
strategy.
Upon receiving any information from WiFi or BT, the WiFi
driver will run the co-existence mechanism immediately.
It will set the RF antenna configuration according to the
strategy through the TDMA H2C to firmware and a hardware
table. Based on the tdma/table, WiFi + BT should work with
each other, and having a better user experience.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
C2H commands that cannot be handled in IRQ context should
be protected by rtwdev->mutex. Because they might have a
sequece of hardware operations that does not want to be
interfered.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the c2h operations are small and can be done
under interrupt context. For the rest that requires
more operations or can go sleep, enqueue onto c2h queue.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration variable IS_LITTLE_ENDIAN is replaced by the standard
__LITTLE_ENDIAN. In addition, an unused struct is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtw88/pci.c: In function 'rtw_pci_phy_cfg':
drivers/net/wireless/realtek/rtw88/pci.c:993:6: warning:
variable 'ip_sel' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now _rtl_dump_channel_map() does not do any actual
thing using the channel. So remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're just trusting that these tables are of the right dimensions, when
we could do better by just using the struct directly. Let's expose the
struct txpwr_lmt_cfg_pair instead.
The table changes were made by using some Vim macros, so that should
help prevent any translation mistakes along the way.
Remaining work: get the 'void *data' out of the generic struct
rtw_table; all of these tables really deserve to be their own data
structure, with proper type fields.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Module parameters of 'sw_crypto' and 'disable_watchdog' are false by
default. If new value is desired, we can do it during inserting module,
assignment existing in source code is not reasonable.
Reported-by: David Binderman <dcb314@hotmail.com>
CC: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a read entry in debugfs to dump current tx power
indexes in use for each path and each rate section.
The corresponding power bases, power by rate, and
power limit are also included.
Also this patch fixes unused function warning.
Fixes: b741422218 ("rtw88: refine flow to get tx power index")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
fix below issue reported by coccicheck
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:514:1-3:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since each skb in RX ring is reused instead of new allocation, we can
treat the DMA in a more efficient way by DMA synchronization.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Testing with RTL8822BE hardware, when available memory is low, we
frequently see a kernel panic and system freeze.
First, rtw_pci_rx_isr encounters a memory allocation failure (trimmed):
rx routine starvation
WARNING: CPU: 7 PID: 9871 at drivers/net/wireless/realtek/rtw88/pci.c:822 rtw_pci_rx_isr.constprop.25+0x35a/0x370 [rtwpci]
[ 2356.580313] RIP: 0010:rtw_pci_rx_isr.constprop.25+0x35a/0x370 [rtwpci]
Then we see a variety of different error conditions and kernel panics,
such as this one (trimmed):
rtw_pci 0000:02:00.0: pci bus timeout, check dma status
skbuff: skb_over_panic: text:00000000091b6e66 len:415 put:415 head:00000000d2880c6f data:000000007a02b1ea tail:0x1df end:0xc0 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:105!
invalid opcode: 0000 [#1] SMP NOPTI
RIP: 0010:skb_panic+0x43/0x45
When skb allocation fails and the "rx routine starvation" is hit, the
function returns immediately without updating the RX ring. At this
point, the RX ring may continue referencing an old skb which was already
handed off to ieee80211_rx_irqsafe(). When it comes to be used again,
bad things happen.
This patch allocates a new, data-sized skb first in RX ISR. After
copying the data in, we pass it to the upper layers. However, if skb
allocation fails, we effectively drop the frame. In both cases, the
original, full size ring skb is reused.
In addition, to fixing the kernel crash, the RX routine should now
generally behave better under low memory conditions.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=204053
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Arguments are supposed to be ordered high then low.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi tx power of RTL8723BU is extremely low after booting. So
the WiFi scan gives very limited AP list and it always fails to
connect to the selected AP. This module only supports 1x1 antenna
and the antenna is switched to bluetooth due to some incorrect
register settings.
Compare with the vendor driver https://github.com/lwfinger/rtl8723bu,
we realized that the 8723bu's enable_rf() does the same thing as
rtw_btcoex_HAL_Initialize() in vendor driver. And it by default
sets the antenna path to BTC_ANT_PATH_BT which we verified it's
the cause of the wifi weak tx power. The vendor driver will set
the antenna path to BTC_ANT_PATH_PTA in the consequent btcoexist
mechanism, by the function halbtc8723b1ant_PsTdma.
This commit hand over the antenna control to PTA(Packet Traffic
Arbitration), which compares the weight of bluetooth/wifi traffic
then determine whether to continue current wifi traffic or not.
After PTA take control, The wifi signal will be back to normal and
the bluetooth scan can also work at the same time. However, the
btcoexist still needs to be handled under different circumstances.
If there's a BT connection established, the wifi still fails to
connect until BT disconnected.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The RISC-V architecture has a register named the "Supervisor Exception
Program Counter", or "sepc". This abbreviation triggers checkpatch.pl's
misspelling detector, resulting in noise in the checkpatch output. The
risk that this noise could cause more useful warnings to be missed seems
to outweigh the harm of an occasional misspelling of "spec". Thus drop
the "sepc" entry from the misspelling list.
[akpm@linux-foundation.org: fix existing "sepc" instances, per Joe]
Link: http://lkml.kernel.org/r/20190518210037.13674-1-paul.walmsley@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a structure for power parameters including base,
offset, limit and a function to get tx power parameters.
Then, refine flow to get tx power index through the
function.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this macro definition has different values in different chipset,
the current defined macro value is for 8822b. This will cause the
settings of 8822c be incorrect.
Remove RTW_MAX_POWER_INDEX and use max_power_index in struct rtw_chip_info
to make sure the value of different chipset is right.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support more regulatory domains including IC, KCC,
ACMA, CHILE, UKRAINE, and MEXICO. Corresponding tx
power limits for these regulatory domains are added
in tx power limit table. Besides, tx power limits in
some case are also updated to follow RF v20 for better
tx power indexes.
Channel plan mapping table are upgraded to consider
more 2G and 5G channel plans combination cases. It
allow us to identify different situations more accuratly
by channel plan IDs. In addition, mapping table for
country code and channel plan ID and mapping table
for country code and tx power limit are also updated
to follow RF v20. It allow the new enrties in tx power
limit table to be applied correctly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If phy rate is decreased, sub bandwidth may be chosen by RA.
We consider possible power limits and apply the min one;
otherwise, the tx power index may be larger than spec.
And we cross-reference power limits of vht and ht with
20/40M bandwidth in 5G to avoid values are not assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we are loading tx power limit from the power limit table, compare
the world-wide limit with the current limit and choose the lowest power
limit for the world-wide power settings.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx power limit is stored separately by 2G and 5G.
But driver did not get tx power limit from 5G and causes incorrect tx
power. Check if the channel is beyond 2G and get the corresponding tx
power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The orig variable is taken but not used, remove it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function names to make them have the same prefix "rtw_phy"
for the tx power setting routines. Only the function names and
corresponding identation are modified.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The type change from (void *) to (struct rtw_dev *) is redundant.
Just pass the right type and compiler can check that for us.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some functions that should be static are unnecessarily exposed, remove
their declaration in header file phy.h.
After resolving their declaration order, they can be declared as static.
So this commit changes nothing except the order and marking them static.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdE5OGAAoJEG4XJFUm622bWCoH/1bLdkTYOkSatXxpHn2cVRvA
SrQ+ZSfOWJe5d0B+9HWhO5r+Savuu+IrgcC6vSIBBVglF5Tf6F0DAxHVrIwc9MSY
QUv4f1suqeH0ipUEBWJXoDXM2OEShvw5WCuY0ZnYw2hZRI7Sb5nqwJEUH57BtBCX
tFW22Ax3ZFTmCfexFgiwEjmtEx6HHz/nleYLMt9gg7X1Twug+QmhEsNw/27PfvMx
RyVyCJ1UvW2x4GHqDRlGxQoh7FlMvuVe/v/VcjGp2Fp8s7GS0xUyA11svGBFpdnT
K94Y3LOcTSdBQwScbn6O2v6EybB9PZYhg6rckwbMgIN2pkkWqXnh5avru4U0T9k=
=yq6Q
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-06-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valu says:
====================
wireless-drivers-next patches for 5.3
First set of patches for 5.3, but not that many patches this time.
This pull request fails to compile with the tip tree due to
ktime_get_boot_ns() API changes there. It should be easy for Linus to
fix it in p54 driver once he pulls this, an example resolution here:
https://lkml.kernel.org/r/20190625160432.533aa140@canb.auug.org.au
Major changes:
airo
* switch to use skcipher interface
p54
* support boottime in scan results
rtw88
* add fast xmit support
* add random mac address on scan support
rt2x00
* add software watchdog to detect hangs, it's disabled by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rtw_writ16_set should be rtw_write16_set
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware default uses management queue to transmit frames that are
downloaded into reserved page, so we need to clearly assign the frames
to use qsel in TX_DESC_QSEL_MGMT to avoid using wrong queue.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DACK is done right after the hardware has been turned on, which
means it will be done every time we leave the IDLE state.
But it takes ~2 seconds to finish DACK.
We can back up the results and restore them. And it only takes a few
milliseconds to restore the results to the hardware, saving a lot of
time.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We could fail to power on because it was already on. If the return
value is -EALREADY, power off and then power on again to turn on the
hardware as expected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
8822c used to count OFDM FA count by subtracting tx count from FA count.
But it need to substract more counters to be accurate.
However, we can count it by adding up all of the FA counters we want.
And it is simpler to add than list all of the components to substract.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver Could fail to reset counter if rx clock gating is not disabled.
So we need to disable rx clock gating before resetting counters.
Otherwise counters may increase unexpected.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In 2G channels, the cck source and rxagc should be set to different
values based on different bandwidth to increase the performance of rx
sensitivity.
To improve rx throughput performance, the values of sbd subtune and
pt_opt should be changed in different bandwidth.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Collision of writing rf registers could occur if the driver writes
rf registers by direct write while the hardware is writing other rf
registers by pi write simultaneously.
Hardware pi write can be triggered by rf calibrations sometimes, so
the driver can not always write rf registers by direct write
protection. Direct write protection can make sure that there is no
hardware pi write during the direct write.
According to some experiments, if we add direct write protection
when switching channel, the performance of rf calibration will not
be affected.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add beacon function setting routines for each hardware port.
If beacon function is not enabled, the hardware is not able
to synchronize with AP's beacon and can miss the beacons
under some scenarios such as PS mode.
For AP and Adhoc modes that require to send beacons, do not
update the TSF, otherwise the beacon interval may be affected.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver uses random mac address to scan, the unicast probe response
will not be received because the addr1 is not matched. Configure port
address by requested mac address to receive probe response from AP.
To support random mac scan, we need to configure the mac address during
scan period to receive unicast prop_resp. After scan is completed,
configure the mac address back to the original one that the port used.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With dynamic power save support, rtw88 is able to support fast tx
path, claim it to mac80211.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable rtstatus is being initialized with a value that is never read
as rtstatus is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The assignment of 0 to variable k is never read once we break out of
the loop, so the assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable badworden is assigned with a value that is never read and
it is re-assigned a new value immediately afterwards. The assignment is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of version 2 of the gnu general public license as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 64 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.894819585@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/rtl_btc.c: In function rtl_btc_btmpinfo_notify:
drivers/net/wireless/realtek/rtlwifi/btcoexist/rtl_btc.c:319:17: warning: variable len set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function exhalbtc_connect_notify:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1581:16: warning: variable asso_type_v2 set but not used [-Wunused-but-set-variable]
'len' is never used since commit 6aad6075cc ("rtlwifi:
Add BT_MP_INFO to c2h handler.") so can be removed.
'asso_type_v2' is not used since introduction in
commit 0843e98a3b ("rtlwifi: btcoex: add assoc
type v2 to connection notify")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function rtl8821ae_dm_check_rssi_monitor:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:658:6: warning: variable cur_txokcnt set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c: In function rtl8821ae_dm_check_edca_turbo:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/dm.c:2657:7: warning: variable b_last_is_cur_rdl_state set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed later.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The cckswing tables cckswing_table_ch1ch13 and cckswing_table_ch14 are
u8 array in little-endian order. To compare four u8 value with register
u32 value, cast the value to cpu order.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ofdm_index_old[] is the index of ofdmswing_table[], and used to indicate
initial value of ROFDM0_X{A,B}TXIQIMBALANCE in rtl8192de_phy_reg_2tarray[]
table, and the initial value is corresponding to calibration thermal value
written in efuse, namely rtlefuse->eeprom_thermalmeter. Then, local
variable ofdm_index_old[] save to rtlpriv->dm.ofdm_index[] for operational
use.
If thermal value (temperature) is increasing, output TX power is lower.
So, we calculate the delta between current and calibration thermal value,
then add power to yield expected and the same output TX power.
Thus, ofdm_index[] should be initialized as rtlpriv->dm.ofdm_index[], and
shift to proper index depends on delta of thermal value. Then, new power
value ofdmswing_table[ofdm_index[]] is written to register.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can reduce code size 264 bytes, and make code more readable.
text data bss dec hex filename
Before: 13586 0 16 13602 3522 rtl8192de/dm.o
After: 13322 0 16 13338 341a rtl8192de/dm.o
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This commit doesn't change logic at all. Since indentation is lower, the
wrapped statements can be put in single line that will become more
readable.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LPS represents Leisure Power Save. When enabled, firmware will be in
charge of turning radio off between beacons. Also firmware should turn
on the radio when beacon is coming, and the data queued should be
transmitted in TBTT period.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dump warning messages when we get a q_mapping larger than the AC
numbers. And pick BE queue as default.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
AC numbers are defined as enum in mac80211, use them instead of bare
0-3 indexing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix sparse warnings:
drivers/net/wireless/realtek/rtw88/phy.c:851:4: warning: symbol 'rtw_cck_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:852:4: warning: symbol 'rtw_ofdm_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:853:4: warning: symbol 'rtw_ht_1s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:854:4: warning: symbol 'rtw_ht_2s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:855:4: warning: symbol 'rtw_vht_1s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/phy.c:856:4: warning: symbol 'rtw_vht_2s_size' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/fw.c:11:6: warning: symbol 'rtw_fw_c2h_cmd_handle_ext' was not declared. Should it be static?
drivers/net/wireless/realtek/rtw88/fw.c:50:6: warning: symbol 'rtw_fw_send_h2c_command' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new rssi_level should be stored in si, otherwise the rssi_level will
never be updated and get a wrong RA mask, which is calculated by the
rssi level
If a wrong RA mask is chosen, the firmware will pick some *bad rates*.
The most hurtful scene will be in *noisy environment*, such as office or
public area with many APs and users.
The latency would be high and the overall throughput would be only half
or less.
Tested in 2.4G in office area, with this patch the throughput increased
from such as "1x Mbps -> 4x Mbps".
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My compiler complains about:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘rtw_phy_rf_power_2_rssi’:
drivers/net/wireless/realtek/rtw88/phy.c:430:26: warning: array subscript is above array bounds [-Warray-bounds]
linear = db_invert_table[i][j];
According to comment power_db should be in range 1 ~ 96 .
To fix add check for boundaries before access the array.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns about the definitions of these macros (full warnings trimmed
for brevity):
drivers/net/wireless/realtek/rtw88/main.c:524:15: warning: signed shift
result (0x3FF00000000) requires 43 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
ra_mask &= RA_MASK_VHT_RATES | RA_MASK_OFDM_IN_VHT;
^~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:527:15: warning: signed shift
result (0xFF0000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
ra_mask &= RA_MASK_HT_RATES | RA_MASK_OFDM_IN_HT_5G;
^~~~~~~~~~~~~~~~
Given that these are all used with ra_mask, which is of type u64, we can
just declare the macros to be ULL as well.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/467
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘rtw_get_channel_group’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:907:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:908:2: note: here
case 1:
^~~~
In file included from ./include/linux/bcd.h:5,
from drivers/net/wireless/realtek/rtw88/phy.c:5:
drivers/net/wireless/realtek/rtw88/phy.c: In function ‘phy_get_2g_tx_power_index’:
./include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:125:2: note: in expansion of macro ‘unlikely’
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:1021:3: note: in expansion of macro ‘WARN_ON’
WARN_ON(1);
^~~~~~~
drivers/net/wireless/realtek/rtw88/phy.c:1022:2: note: here
case RTW_CHANNEL_WIDTH_20:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the shift of an integer value more than 32 bits can
occur when nss is more than 32. Fix this by making the integer
constants unsigned long longs before shifting and bit-wise or'ing
with the u64 ra_mask to avoid the undefined shift behaviour.
Addresses-Coverity: ("Bad shift operation")
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a new mac80211 driver for Realtek 802.11ac wireless network chips.
rtw88 now supports RTL8822BE/RTL8822CE now, with basic station mode
functionalities. The firmware for both can be found at linux-firmware.
https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
For RTL8822BE: rtw88/rtw8822b_fw.bin
For RTL8822CE: rtw88/rtw8822c_fw.bin
And for now, only PCI buses (RTL8xxxE) are supported. We will add support
for USB and SDIO in the future. The bus interface abstraction can be seen
in this driver such as hci.h. Most of the hardware setting are the same
except for some TRX path or probing setup should be separated.
Supported:
* Basic STA/AP/ADHOC mode, and TDLS (STA is well tested)
Missing feature:
* WOW/PNO
* USB & SDIO bus (such as RTL8xxxU/RTL8xxxS)
* BT coexistence (8822B/8822C are combo ICs)
* Multiple interfaces (for now single STA is better supported)
* Dynamic hardware calibrations (to improve/stabilize performance)
Potential problems:
* static calibration spends too much time, and it is painful for
driver to leave IDLE state. And slows down associate process.
But reload function are under development, will be added soon!
* TRX statictics misleading, as we are not reporting status correctly,
or say, not reporting for "every" packet.
The next patch set should have BT coexistence code since RTL8822B/C are
combo ICs, and the driver for BT can be found after Linux Kernel v4.20.
So it is better to add it first to make WiFi + BT work concurrently.
Although now rtw88 is simple but we are developing more features for it.
Even we want to add support for more chips such as RTL8821C/RTL8814B.
Finally, rtw88 has many authors, listed alphabetically:
Ping-Ke Shih <pkshih@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c: In function 'rtl92cu_phy_rf6052_set_cck_txpower':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:45:7: warning: variable 'turbo_scanoff' set but not used [-Wunused-but-set-variable]
It is not used any more since
commit e9b0784bb9 ("rtlwifi: rtl8192cu: Fix some code in RF handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add missing break statement in order to prevent the code from falling
through to case 0x1025, and erroneously setting rtlhal->oem_id to
RT_CID_819X_ACER when rtlefuse->eeprom_svid is equal to 0x10EC and
none of the cases in switch (rtlefuse->eeprom_smid) match.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 238ad2ddf3 ("rtlwifi: rtl8723ae: Clean up the hardware info routine")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Somehow file drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c.rej was
incorporated into the sources. Obviously, it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix sparse warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/dm.c:666:6:
warning: symbol 'rtl8723e_dm_refresh_rate_adaptive_mask' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In five of the drivers, the contents of bits 29-31 of one of the RX
descriptors is used to set bits in a variable that is used to save the
wakeup condition for output in a debugging statement. The resulting
variable is not used anywhere else even though it is stored in a struct
and could be available in other routines. This variable is changed to be
local.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In drivers rtl8188ee, rtl8821ae, rtl8723be, and rtl8192ee, the reason
for a wake-up is returned in the fourth RX descriptor in bits 29-31. Due
to typographical errors, all but rtl8821ae test bit 31 twice and fail to
test bit 29.
This error causes no problems as the tests are only used to set bits in
the output of an optional debugging statement.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is unnecessary to call spin_lock_bh in a tasklet.
Signed-off-by: Jeff Xie <chongguiguzi@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case dev_alloc_skb fails, the fix safely returns to avoid
potential NULL pointer dereference.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case alloc_workqueue fails, the fix reports the error and
returns to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c: In function '_rtl92s_firmware_downloadcode':
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c:139:17: warning:
variable 'seg_ptr' set but not used [-Wunused-but-set-variable]
It's not used after commit 59ae1d127a ("networking: introduce and use
skb_put_data()")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c: In function '_rtl8723e_dm_bt_coexist_2_ant':
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:1408:5: warning:
variable 'bt_retry_cnt' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c: In function 'rtl8723be_dm_check_edca_turbo':
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:998:7: warning:
variable 'b_last_is_cur_rdlstate' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following types of blank line problems are reported:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following problems were found:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum declarations
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The problems filed include the following:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The errors consist of multiple blank lines, and a missing blank line
after the declarations.
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The instances where statement continuations are improperly aligned have
been fixed.
There are no changes to generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of problems with block comments.
These changes do not affect the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl report problems in wifi.h where spaces are missing, as well
as extraneous spaces.
There are no changes in the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is an uppercase 'N' that should be a lowercase 'n', fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c: In function 'rtl8180_probe':
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1727:15: warning:
variable 'io_addr' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c:1726:16: warning:
variable 'mem_addr' set but not used [-Wunused-but-set-variable]
They're never used since introduction.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
WARNING: line over 80 characters
#316: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/fw.c:1751:
+ SET_8821AE_H2CCMD_AOAC_RSVDPAGE_LOC_GTK_EXT_MEM(u1rsvdpageloc2, GTKEXT_PG);
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#357: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2591:
+ (eeaddr+1), hwinfo[eeaddr+1]);
^
CHECK: spaces preferred around that '+' (ctx:VxV)
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
^
WARNING: Comparisons should place the constant on the right side of the test
#358: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2592:
+ if (0xFF == hwinfo[eeaddr+1]) /*YJ,add,120316*/
CHECK: spaces preferred around that '&' (ctx:VxV)
#501: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8821ae/hw.c:2666:
+ pwrinfo24g->bw40_diff[rfpath][txcount] = (hwinfo[eeaddr]&0xf0) >> 4;
^
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a macro is in CamelCase, it it converted to upper case. Variables
and routine names are converted to lower case.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#211: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:109:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#241: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/hw.c:277:
+ ptmp_byte = (u8 *) (®toset) + index;
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch affects modules rtl8192ce, rtl8192cu, and rtl8192com.
The following checkpatch exceptions are also fixed:
CHECK: No space is necessary after a cast
#237: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/hw.c:90:
+ (u8 *) (&rfstate));
CHECK: No space is necessary after a cast
#744: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:329:
+ pwr_val[i] = (u8) ((writeval & (0x7f <<
CHECK: No space is necessary after a cast
#784: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/rf.c:365:
+ (u8) writeval);
CHECK: spaces preferred around that '/' (ctx:VxV)
#963: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:513:
+ txqpageunit = txqpagenum/outepnum;
^
CHECK: Unnecessary parentheses around 'outepnum > 1'
#975: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:521:
+ if ((outepnum > 1) && (txqremaininpage))
CHECK: Alignment should match open parenthesis
#1059: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/hw.c:617:
+static void _rtl92cu_init_chipn_two_out_ep_priority(struct ieee80211_hw *hw,
bool wmm_enable,
ERROR: "foo * bar" should be "foo *bar"
#1940: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:591:
+void rtl92cu_fill_fake_txdesc(struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver contains one instance of a CamelCase variable, namely
IS_81xxC_VENDOR_UMC_A_CUT. This macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbt_precomp.h contains the only CamelCase value, namely
GetDefaultAdapter, but that macro is never used, thus it is deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a number of CamelCase variables remaining in the source
files of modules rtl_pci, rtl_usb, and rtlwifi.
The following checkpatch excettions are also fixed:
for_kalle1/0001-rtlwifi-Remove-CamelCase-variables-from-base-code.patch
-----------------------------------------------------------------------
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
CHECK: Unnecessary parentheses around 'rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1]'
#68: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:377:
+ if ((rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i]) ||
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
+ rtlefuse->efuse_map[EFUSE_MODIFY_MAP][base + i +
1])) {
WARNING: line over 80 characters
#70: FILE: drivers/net/wireless/realtek/rtlwifi/efuse.c:379:
+ (rtlefuse->efuse_map[EFUSE_INIT_MAP][base + i + 1] !=
CHECK: No space is necessary after a cast
#186: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c:396:
+ status->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#208: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c:335:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#243: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:301:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
CHECK: No space is necessary after a cast
#252: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:368:
+ stats.rx_is40mhzpacket = (bool) GET_RX_DESC_BW(rxdesc);
CHECK: No space is necessary after a cast
#265: FILE: drivers/net/wireless/realtek/rtlwifi/rtl8192de/trx.c:475:
+ stats->rx_is40mhzpacket = (bool) GET_RX_DESC_BW(pdesc);
WARNING: Unnecessary space before function pointer arguments
#455: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:1462:
+ void (*writen_sync) (struct rtl_priv *rtlpriv, u32 addr, void *buf,
WARNING: Unnecessary space before function pointer arguments
#483: FILE: drivers/net/wireless/realtek/rtlwifi/wifi.h:2257:
+ void (*fill_fake_txdesc) (struct ieee80211_hw *hw, u8 *pdesc,
Note that not all checkpatch exceptions are addressed. Those will be
handled in later patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old-style license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/base.c: In function 'rtl_c2h_content_parsing':
drivers/net/wireless/realtek/rtlwifi/base.c:2313:13: warning:
variable 'cmd_seq' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the Kbuild core manipulates header search paths in a crazy
way [1].
To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.
Having whitespaces after -I does not matter since commit 48f6e3cf5b
("kbuild: do not drop -I without parameter").
I also removed one header search path in:
drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile
I was able to compile without it.
[1]: https://patchwork.kernel.org/patch/9632347/
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a statement that is indented too deeply. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch moves the clearing of rtlpriv->link_info.num_rx_inperiod in
rtl_watchdog_wq_callback a few lines down.
This is necessary since it is still used in the "AP off" detection
code block. Moved clearing of rtlpriv->link_info.num_rx_inperiod
as well for consistency.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This re-introduces the function rtl8723e_dm_refresh_rate_adaptive_mask.
This function was present in a previous version of the code base,
it works just fine for me -- as long as it is not using stale data.
Unlike the original version of this function it avoids using
dm.undec_sm_pwdb when no beacon was received.
Fixed a style nit in rtl8723e_dm_init_rate_adaptive_mask.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When no beacon was received, the value in dm.undec_sm_pwdb is most
likely out of date and should not be used to adjust the input path.
Assume instead that the signal level is low.
Fix the state machine in rtl8723e_dm_cck_packet_detection_thresh
which did not clear pre_cck_fa_state when changing cur_cck_pd_state
from CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW to CCK_PD_STAGE_HIGHRSSI
and back again to CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW, the register
RCCK0_CCA not written to 0x83 on the second change.
Explicitly initialize pre_cck_fa_state/cur_cck_fa_state in
rtl_dm_diginit.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This appears to trigger a firmware bug and causes severe
problems with rtl8723ae PCI devices.
When the power save mode is activated for longer periods
of time the firmware stops to receive any packets.
This problem was exposed by commit 873ffe154a ("rtlwifi:
Fix logic error in enter/exit power-save mode").
Previously the power save mode was only active rarely and
only for a short time so that the problem was not noticeable.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c: In function 'translate_rx_signal_stuff':
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c:309:6: warning:
variable 'type' set but not used [-Wunused-but-set-variable]
It never used since commit 21e4b0726d ("rtlwifi: rtl8821ae: Move driver from
staging to regular tree")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.
Signed-off-by: Pan Bian <bianpan2016@163.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing
C2H_BT_INFO"), calling rtl_c2hcmd_enqueue() with rtl_c2h_fast_cmd() true,
the routine returns without freeing that skb, thereby leaking it.
This issue has been discussed at https://github.com/lwfinger/rtlwifi_new/issues/401
and the fix tested there.
Fixes: 0a9f8f0a1b ("rtlwifi: fix btmpinfo timeout while processing C2H_BT_INFO")
Reported-and-tested-by: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Francisco Machado Magalhães Neto <franmagneto@gmail.com>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RT_TRACE shows REG_MCUFWDL value as a decimal value with a '0x'
prefix, which is somewhat misleading.
Fix it to print hexadecimal, as was intended.
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
radiob_array_table' and 'radiob_arraylen' are not used after setting its value.
It is safe to remove the unused variable. Meanwhile, radio B array should be
removed as well. because it will no longer be referenced.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add missing break statement in order to prevent the code from falling
through to the default case.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357355 ("Missing break in switch")
Addresses-Coverity-ID: 1357378 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function 'halbtc_leave_lps':
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:295:21: warning:
variable 'ppsc' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c: In function 'halbtc_enter_lps':
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:318:21: warning:
variable 'ppsc' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit aa45a673b2 ("rtlwifi: btcoexist: Add new mini driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c: In function 'rtl8xxxu_tx':
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4925:7: warning:
variable 'usedesc40' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:4921:6: warning:
variable 'seq_number' set but not used [-Wunused-but-set-variable]
'usedesc40' and 'seq_number' are not used any more after
commit b59415c2dd ("rtl8xxxu: Split filling of TX descriptors into separate functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl8821ae_mrate_idx_to_arfr_id is functionally identical to
the generic version rtl_mrate_idx_to_arfr_id, so remove
_rtl8821ae_mrate_idx_to_arfr_id and use the generic one instead.
This also fixes a missing break statement found by CoverityScan in
_rtl8821ae_mrate_idx_to_arfr_id, namely: CID#1167237 ("Missing break
in switch")
Thanks to Joe Perches for spotting this when I submitted an earlier patch.
Fixes: 3c05bedb5f ("Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
ACKed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following:
bool efuse_re_pg_sec1flag;
u8 efuse_re_pg_data[8];
are not referenced anywhere in the rtlwifi code.
This patch is originally created by Rick Veens <rickveens92@gmail.com>,
and Joe Perches <joe@perches.com> reminded to apply it to rtlwifi.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1327:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_PCI;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1330:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_USB;
~ ^~~~~~~~~~~~
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:1333:34:
warning: implicit conversion from enumeration type 'enum
btc_chip_interface' to different enumeration type 'enum
wifionly_chip_interface' [-Wenum-conversion]
wifionly_cfg->chip_interface = BTC_INTF_UNKNOWN;
~ ^~~~~~~~~~~~~~~~
3 warnings generated.
Use the values from the correct enumerated type, wifionly_chip_interface.
BTC_INTF_UNKNOWN = WIFIONLY_INTF_UNKNOWN = 0
BTC_INTF_PCI = WIFIONLY_INTF_PCI = 1
BTC_INTF_USB = WIFIONLY_INTF_USB = 2
Link: https://github.com/ClangBuiltLinux/linux/issues/135
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Eliminate the assumption that SKBs and SKB list heads can
be cast to eachother in SKB list handling code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove set but unused variables from _rtl88ee_hw_configure() and
_rtl8723e_hw_configure().
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Realtek rtl8188ctv (0x0bda:0x018a) is a highly integrated single-chip
WLAN USB2.0 network interface controller.
Currently rtl8188ctv is supported by rtlwifi driver.
It is similar to the rtl8188cus(0x0bda:0x818a) and uses the same config.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In gcc8, when the 3rd argument (size) of a call to strncpy() matches the
length of the first argument, the compiler warns of the possibility of an
unterminated string. Using strlcpy() forces a null at the end.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix following coccinelle warning:
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2952:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2961:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3011:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3020:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3439:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3448:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3339:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3348:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3074:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3083:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3192:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3201:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3267:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3276:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3124:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3133:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2821:2-4: WARNING: possible condition with no effect (if == else)
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:2830:2-4: WARNING: possible condition with no effect (if == else)
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8225se_rf_init() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This patch only replaces the mdelay() that has >20ms time to wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sNaA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, firmware will not run properly on rtl8821ae, and it
causes bad user experience. For example, bad connection performance with
low rate, higher power consumption, and so on.
rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and
each firmware has firmware data buffer and size individually. Original
code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and
this mismatch causes firmware checksum error, then firmware can't start.
In this situation, driver gives message "Firmware is not ready to run!".
Fixes: fe89707f0a ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When connecting to AP, mac80211 asks driver to enter and leave PS quickly,
but driver deinit doesn't wait for delayed work complete when entering PS,
then driver reinit procedure and delay work are running simultaneously.
This will cause unpredictable kernel oops or crash like
rtl8723be: error H2C cmd because of Fw download fail!!!
WARNING: CPU: 3 PID: 159 at drivers/net/wireless/realtek/rtlwifi/
rtl8723be/fw.c:227 rtl8723be_fill_h2c_cmd+0x182/0x510 [rtl8723be]
CPU: 3 PID: 159 Comm: kworker/3:2 Tainted: G O 4.16.13-2-ARCH #1
Hardware name: ASUSTeK COMPUTER INC. X556UF/X556UF, BIOS X556UF.406
10/21/2016
Workqueue: rtl8723be_pci rtl_c2hcmd_wq_callback [rtlwifi]
RIP: 0010:rtl8723be_fill_h2c_cmd+0x182/0x510 [rtl8723be]
RSP: 0018:ffffa6ab01e1bd70 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffa26069071520 RCX: 0000000000000001
RDX: 0000000080000001 RSI: ffffffff8be70e9c RDI: 00000000ffffffff
RBP: 0000000000000000 R08: 0000000000000048 R09: 0000000000000348
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: ffffa26069071520 R14: 0000000000000000 R15: ffffa2607d205f70
FS: 0000000000000000(0000) GS:ffffa26081d80000(0000) knlGS:000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000443b39d3000 CR3: 000000037700a005 CR4: 00000000003606e0
Call Trace:
? halbtc_send_bt_mp_operation.constprop.17+0xd5/0xe0 [btcoexist]
? ex_btc8723b1ant_bt_info_notify+0x3b8/0x820 [btcoexist]
? rtl_c2hcmd_launcher+0xab/0x110 [rtlwifi]
? process_one_work+0x1d1/0x3b0
? worker_thread+0x2b/0x3d0
? process_one_work+0x3b0/0x3b0
? kthread+0x112/0x130
? kthread_create_on_node+0x60/0x60
? ret_from_fork+0x35/0x40
Code: 00 76 b4 e9 e2 fe ff ff 4c 89 ee 4c 89 e7 e8 56 22 86 ca e9 5e ...
This patch ensures all delayed works done before entering PS to satisfy
our expectation, so use cancel_delayed_work_sync() instead. An exception
is delayed work ips_nic_off_wq because running task may be itself, so add
a parameter ips_wq to deinit function to handle this case.
This issue is reported and fixed in below threads:
https://github.com/lwfinger/rtlwifi_new/issues/367https://github.com/lwfinger/rtlwifi_new/issues/366
Tested-by: Evgeny Kapun <abacabadabacaba@gmail.com> # 8723DE
Tested-by: Shivam Kakkar <shivam543@gmail.com> # 8723BE on 4.18-rc1
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: cceb0a5973 ("rtlwifi: Add work queue for c2h cmd.")
Cc: Stable <stable@vger.kernel.org> # 4.11+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bump the IEEE80211_MAX_AMPDU_BUF size to 0x100 for HE support
and - for now - use IEEE80211_MAX_AMPDU_BUF_HT everywhere.
This is derived from my internal patch, parts of which Luca
had sent upstream.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbD/3rAAoJEG4XJFUm622b1ZwH/1xe1IqcwJXzfoDsYPlXVnSh
TiLExjKkD0ty5M0//844FxpxE1sSYJKOJ11uz/COzyG2qi4+5lgpUdjnDoINuKfH
ycqrXGssW7ogPWkVvnxKtlEYvkHNRYLQtxvd26umT77C69jVJLD0x9uihhh2En/C
EKs+OK1Pp0SRvTfB4AblWzoAnpEe1wHJFFh4i3F5H0lMGxLQz/YjFl5aeAjjR406
0vSKLGy2wKIydp8Pe4cAqBEeUWDJurn8ufkk7bmAET5zaXTH1qgZzLH3OWtx/ksz
mcPQq9/ctv35G2917t3Sn69SIUCDGfYkP5DiZV+ti0Hz2gIV0zOg7mGYCU8uHaU=
=11X5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
Hopefully the last pull request to 4.18 before the merge window.
Nothing major here, we have smaller new features and of course a lots
of fixes.
Major changes:
ath10k
* add memory dump support for QCA9888 and QCA99X0
* add support to configure channel dwell time
* support new DFS host confirmation feature in the firmware
ath
* update various regulatory mappings
wcn36xx
* various fixes to improve reliability
* add Factory Test Mode support
brmfmac
* add debugfs file for reading firmware capabilities
mwifiex
* support sysfs initiated device coredump
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and refactor some code in order to avoid having identical code
for different branches.
Notice that the logic has been there since 2014.
Addresses-Coverity-ID: 1426199 ("Identical code for different branches")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In former patch, I enqueu all C2H commands and processed by a workqueue.
In case C2H_BT_INFO will issue a H2C command to set BT reg, and wait for
a C2H ack. But it is totally impossible that C2H workqueue waits for a
C2H command, so kernel log warn
rtlwifi: :<0> btmpinfo wait (req_num=0) timeout
Since the C2H ack command C2H_BT_MP can be safely processed in interrupt
context, add a fast command path to deal with the command.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The format of C2H data is ID(1 byte) + Length(1 byte) + value, and it is
more readable to use macros to access C2H data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We use 'struct rtl_c2hcmd' to store C2H commands originally, and the code
is slightly complex to enqueue and dequeue and also wastes time to
allocate and memcpy data. Since C2H commands are asynchronous events,
they can be processed in work queue, so RX ISR enqueues C2H result in
removal of rtl_c2h_packet_handler().
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Similar to rx_command_packet, we can call rtl_c2h_content_parsing so the
hal_op isn't necessary.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge duplicate C2H handler and implement the handler in base.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We're going to merge C2H handler into one, but one special case is to
handle RA_REPORT that implements in individual IC folder. So this commit
adds a hal_op for caller in common code.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The caller of hal_op rx_command_packet will assert function pointer
before calling, so we can remove dummy functions safely.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IDs are defined by driver and map to the fw C2H IDs, but they aren't
used now result in removal.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move C2H definition to wifi.h, because the definitions of 8192ee, 8723be
and 8821ae are the same.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current chips use packet-based C2H commands whose IDs differ from old
ones, so this commit simply gives C2H_V0_ as prefix of command IDs.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move duplicate definitions from def.h of ic folder to wifi.h
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To use keep-alive mechanism in mac80211 stack, since driver supports
reporting accurate nullfunc frame tx ack now.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to realize the keep-alive mechanism in mac80211 stack, reporting
accurate tx ack status for nullfunc frame is added in this commit.
If current frame is nullfunc frame, we ask firmware to report by filling
TX report bit in TX descriptor. After this frame DMA done, TX interrupt is
triggered but TX status is unknown at this moment, so enqueue this skb
into tx_report->queue. Finally, C2H report will be received if the frame
is transmitted successfully or retried over, and then we report to mac80211
with IEEE80211_TX_STAT_ACK flag only if it's successful. Otherwise, if
failure or timeout (one second), we report to mac80211 without this flag.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two enumerations bt_total_ant_num and bt_ant_num are identical, so one
can be removed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in RT_TRACE message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To fix a conflict reported by Stephen Rothwell <sfr@canb.auug.org.au>:
Today's linux-next merge of the wireless-drivers-next tree got a
conflict in:
drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
between commit:
77e30e10ee ("iwlwifi: mvm: query regdb for wmm rule if needed")
from the wireless-drivers tree and commits:
9c4f7d5127 ("iwlwifi: move all NVM parsing code to the common files")
4c625c564b ("iwlwifi: get rid of fw/nvm.c")
from the wireless-drivers-next tree.
Since the statements are identical, we can safely remove the statements.
The commit 42e74946f0 ("rtlwifi: btcoexist: Fix if == else warnings in
halbtc8821a1ant.c") had fixed the statements, but the commit c6821613e6
("rtlwifi: btcoex: follow linux coding style") that converted coding style
and upgraded btcoex didn't include the fix.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some HP laptops have only a single wifi antenna. This would not be a
problem except that they were shipped with an incorrectly encoded
EFUSE. It should have been possible to open the computer and transfer
the antenna connection to the other terminal except that such action
might void the warranty, and moving the antenna broke the Windows
driver. The fix was to add a module option that would override the
EFUSE encoding. That was done with commit c18d8f5095 ("rtlwifi:
rtl8723be: Add antenna select module parameter"). There was still a
problem with Bluetooth coexistence, which was addressed with commit
baa1702290 ("rtlwifi: btcoexist: Implement antenna selection").
There were still problems, thus there were commit 0ff78adeef
("rtlwifi: rtl8723be: fix ant_sel code") and commit 6d62269283
("rtlwifi: btcoexist: Fix antenna selection code"). Despite all these
attempts at fixing the problem, the code is not yet right. A proper
fix is important as there are now instances of laptops having
RTL8723DE chips with the same problem.
The module parameter ant_sel is used to control antenna number and path.
At present enum ANT_{X2,X1} is used to define the antenna number, but
this choice is not intuitive, thus change to a new enum ANT_{MAIN,AUX}
to make it more readable. This change showed examples where incorrect
values were used. It was also possible to remove a workaround in
halbtcoutsrc.c.
The experimental results with single antenna connected to specific path
are now as follows:
ant_sel ANT_MAIN(#1) ANT_AUX(#2)
0 -8 -62
1 -62 -10
2 -6 -60
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: c18d8f5095 ("rtlwifi: rtl8723be: Add antenna select module parameter")
Fixes: baa1702290 ("rtlwifi: btcoexist: Implement antenna selection")
Fixes: 0ff78adeef ("rtlwifi: rtl8723be: fix ant_sel code")
Fixes: 6d62269283 ("rtlwifi: btcoexist: Fix antenna selection code")
Cc: Stable <stable@vger.kernel.org> # 4.7+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge updates from Andrew Morton:
- a few misc things
- ocfs2 updates
- the v9fs maintainers have been missing for a long time. I've taken
over v9fs patch slinging.
- most of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (116 commits)
mm,oom_reaper: check for MMF_OOM_SKIP before complaining
mm/ksm: fix interaction with THP
mm/memblock.c: cast constant ULLONG_MAX to phys_addr_t
headers: untangle kmemleak.h from mm.h
include/linux/mmdebug.h: make VM_WARN* non-rvals
mm/page_isolation.c: make start_isolate_page_range() fail if already isolated
mm: change return type to vm_fault_t
mm, oom: remove 3% bonus for CAP_SYS_ADMIN processes
mm, page_alloc: wakeup kcompactd even if kswapd cannot free more memory
kernel/fork.c: detect early free of a live mm
mm: make counting of list_lru_one::nr_items lockless
mm/swap_state.c: make bool enable_vma_readahead and swap_vma_readahead() static
block_invalidatepage(): only release page if the full page was invalidated
mm: kernel-doc: add missing parameter descriptions
mm/swap.c: remove @cold parameter description for release_pages()
mm/nommu: remove description of alloc_vm_area
zram: drop max_zpage_size and use zs_huge_class_size()
zsmalloc: introduce zs_huge_class_size()
mm: fix races between swapoff and flush dcache
fs/direct-io.c: minor cleanups in do_blockdev_direct_IO
...
Currently <linux/slab.h> #includes <linux/kmemleak.h> for no obvious
reason. It looks like it's only a convenience, so remove kmemleak.h
from slab.h and add <linux/kmemleak.h> to any users of kmemleak_* that
don't already #include it. Also remove <linux/kmemleak.h> from source
files that do not use it.
This is tested on i386 allmodconfig and x86_64 allmodconfig. It would
be good to run it through the 0day bot for other $ARCHes. I have
neither the horsepower nor the storage space for the other $ARCHes.
Update: This patch has been extensively build-tested by both the 0day
bot & kisskb/ozlabs build farms. Both of them reported 2 build failures
for which patches are included here (in v2).
[ slab.h is the second most used header file after module.h; kernel.h is
right there with slab.h. There could be some minor error in the
counting due to some #includes having comments after them and I didn't
combine all of those. ]
[akpm@linux-foundation.org: security/keys/big_key.c needs vmalloc.h, per sfr]
Link: http://lkml.kernel.org/r/e4309f98-3749-93e1-4bb7-d9501a39d015@infradead.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Michael Ellerman <mpe@ellerman.id.au> [2 build failures]
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [2 build failures]
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: John Johansen <john.johansen@canonical.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
Trivial fix to spelling mistake in RT_TRACE message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net?
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct comment. Set bit 3 and bit 4 of 0x0005 register (REG_APS_FSMCO + 1)
to 0 which means disable WL suspend, not enable WL suspend.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex support multiple platforms, but this drivers doesn't support full
functions yet, so this commit adds dummy definitions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New constant and variables definitions are used by btcoex of 8822b, so
this commit add them.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In connection notify v1, btcoex only need to know start/end association,
and it will discriminate 2G and 5G band in v2.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Normal LPS is decomposed into pre- and post- parts, so we can issue H2C
with TDMA parameters in the "critical section" that dirver can't change
LPS state at the moment.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Get phydm's counter and version from the module phydm that is not
submitted so we implement dummy functions.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The btcoex use the rate to rsolve IOT issue that some APs reduce TX
rate quickly, so it uses the RX rate as a clue to decide TDMA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger#lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex does different decision according to MCC or SCC status, but
driver is still SCC currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add customer_id field in structure, and then this is a clue to implement
the behavior defined by vendor LENOVO_CHINA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
btcoex uses dm's counters to check the environment is noisy or not. If it
is clean, btcoex set more time slots to WiFi so that it can transmit as
soon as possible. That will save time, and BT will have more time slots
after WiFi traffic is complete.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports "rtl_is_special_data() warn: inconsistent indenting", but
it is an obvious redundant statement so remove it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sparse reports some functions were not declared, so add 'static' as
modifier. Remove an unused function btc8821a1ant_is_wifi_status_changed()
exposed due to 'static'.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes spelling typos found in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This can be reproduced by bind/unbind the driver multiple times
in AM3517 board.
Analysis revealed that rtl8187_start() was invoked before probe
finishes(ie. before the mutex is initialized).
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
[<c010e0d8>] (unwind_backtrace) from [<c010beac>] (show_stack+0x10/0x14)
[<c010beac>] (show_stack) from [<c017401c>] (register_lock_class+0x4f4/0x55c)
[<c017401c>] (register_lock_class) from [<c0176fe0>] (__lock_acquire+0x74/0x1938)
[<c0176fe0>] (__lock_acquire) from [<c0178cfc>] (lock_acquire+0xfc/0x23c)
[<c0178cfc>] (lock_acquire) from [<c08aa2f8>] (mutex_lock_nested+0x50/0x3b0)
[<c08aa2f8>] (mutex_lock_nested) from [<c05f5bf8>] (rtl8187_start+0x2c/0xd54)
[<c05f5bf8>] (rtl8187_start) from [<c082dea0>] (drv_start+0xa8/0x320)
[<c082dea0>] (drv_start) from [<c084d1d4>] (ieee80211_do_open+0x2bc/0x8e4)
[<c084d1d4>] (ieee80211_do_open) from [<c069be94>] (__dev_open+0xb8/0x120)
[<c069be94>] (__dev_open) from [<c069c11c>] (__dev_change_flags+0x88/0x14c)
[<c069c11c>] (__dev_change_flags) from [<c069c1f8>] (dev_change_flags+0x18/0x48)
[<c069c1f8>] (dev_change_flags) from [<c0710b08>] (devinet_ioctl+0x738/0x840)
[<c0710b08>] (devinet_ioctl) from [<c067925c>] (sock_ioctl+0x164/0x2f4)
[<c067925c>] (sock_ioctl) from [<c02883f8>] (do_vfs_ioctl+0x8c/0x9d0)
[<c02883f8>] (do_vfs_ioctl) from [<c0288da8>] (SyS_ioctl+0x6c/0x7c)
[<c0288da8>] (SyS_ioctl) from [<c0107760>] (ret_fast_syscall+0x0/0x1c)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = cd1ec000
[00000000] *pgd=8d1de831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 821 Comm: wpa_supplicant Not tainted 4.9.80-dirty #250
Hardware name: Generic AM3517 (Flattened Device Tree)
task: ce73eec0 task.stack: cd1ea000
PC is at mutex_lock_nested+0xe8/0x3b0
LR is at mutex_lock_nested+0xd0/0x3b0
Cc: stable@vger.kernel.org
Signed-off-by: Sudhir Sreedharan <ssreedharan@mvista.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was detected with static analysis using Coccinelle:
./drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b1ant.c:1107:5-18:
duplicated argument to && or ||
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-8 points out that source and destination of the memcpy() are
always the same pointer, so the effect of memcpy() is undefined
here (its arguments must not overlap):
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c: In function '_rtl_rx_process':
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/trx.c:430:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
Most likely this is harmless, but it's easy to just remove the
line and get rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In _rtl92c_get_txpower_writeval_by_regulatory() the variable writeVal
is assigned to itself in an if ... else statement, apparently only to
document that the branch condition is handled and that a previously read
value should be returned unmodified. The self-assignment causes clang to
raise the following warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192cu/rf.c:304:13:
error: explicitly assigning value of variable of type 'u32'
(aka 'unsigned int') to itself [-Werror,-Wself-assign]
writeVal = writeVal;
Delete the branch with the self-assignment.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wifi only btcoex is used to solo card (without BT), and it is also
useful to exclude the interference with BT to make debug easier.
There are only four ops for wifi only btcoex to initialze antenna and
switch the settings while band is changed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tell wifi and BT firmware the default port ID to set multiports' state
properly, but only 8822be needs this function currently.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new component phydm need to access efuse content, so we prepare ops
for reference.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tzu-En Huang