There is an additional CCIN for the IBM CFFPS that may be classifed as
either version one or version two, based upon the rest of the bits of
the CCIN. Add support for it in the version detection.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1583948590-17220-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TPS53647 and TPS53667 are single channel, Step-Down Buck Controllers.
TPS53647 supports 4 phases, TPS53667 supports 6 phases.
The chips do not support per-phase output telemetry.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All chips of this series with published datasheets support IIN, PIN, and
STATUS_INPUT PMBus commands. Per TI Power Management Forum, "TPS53679 and
TPS53681 have the same PMBus command set". There is no reason to believe
that this does not apply to TPS53688. Let's assume that this is correct
and add support for IIN, PIN, and STATUS_INPUT to TPS53679 and TPS53688
to simplify adding support for more chips of the same series.
At the same time, drop reporting VIN on channel 2. On chips with published
datasheets this voltage is identical to the voltage reported on channel 1,
and there is no reason to believe that this is different for TPS53679 and
TPS53888.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Chip specific support will be needed in the driver to be able to
support additional chips of the same series. Add support for it
to the driver.
To simplify adding support for more chips, call identification code
from the probe function. This lets us use a single structure for common
elements of struct pmbus_driver_info, thus reducing code size as support
for more chips is added.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips support multiple phases, and report telemetry such
as input current, output current, or temperature for each phase.
Add support for such chips to the PMBus core.
Start with a maximum of 8 phases per page, and assume that supported
sensors per phase are similar for all pages. Only support per-phase
telemetry attributes, no limits or alarms.
As part of this patch, set the initial page variable to 0xff to ensure
that the page is updated when the first page command is issued. Also
only issue page commands if the chip supports more than one page.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation for multi-phase support, add 'phase' parameter to read_word
and set_page functions. Actual multi-phase support will be added in
a subsequent patch.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent PMBus versions added IC_DEVICE_ID and IC_DEVICE_REV commands as
additional means to identify the chip. Add command definitions to
pmbus.h include file.
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Provide read_word_data() callback for overvoltage and undervoltage
output readouts conversion. These registers are presented in
'slinear11' format, while default conversion for 'vout' class for the
devices is 'vid'. It is resulted in wrong conversion in pmbus_reg2data()
for in{3-4}_lcrit and in{3-4}_crit attributes.
)
Fixes: aaafb7c8eb ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200224225202.19576-1-vadimp@mellanox.com
[gropeck: Adjusted to mainline PMBus API]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure that the driver compatible strings matches the binding by
removing the space between the manufacturer and model.
Fixes: aaafb7c8eb ("hwmon: (pmbus) Add support for Infineon Multi-phase xdpe122 family controllers")
Cc: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200212092426.24012-1-johan@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.
Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bb ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for devices XDPE12254, XDPE12284.
All these device support two pages.
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps, supported by these
devices:
VR12.0 mode, 5-mV DAC - 0x01;
VR12.5 mode, 10-mV DAC - 0x02;
IMVP9 mode, 5-mV DAC - 0x03;
AMD mode 6.25mV - 0x10.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-5-vadimp@mellanox.com
[groeck: Added missing break statement]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Extend "vrm_version" with the type for Intel IMVP9 and AMD 6.25mV VID
modes.
Add calculation for those types.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-3-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for VID protocol detection per page bases, instead of
detecting it based on "PMBU_VOUT" readout from page 0 for all the pages
supported by particular device.
The reason that some devices allows to configure different VID modes
per page within the same device.
Patch modifies the field "vrm_version" within the structure
"pmbus_driver_info" to be per page array.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Link: https://lore.kernel.org/r/20200113150841.17670-2-vadimp@mellanox.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the user write parameters resulted in no bytes being written to the
temporary buffer, then ON_OFF_CONFIG will be written with uninitialized
data. Prevent this by bailing out in this case.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1578411640-16929-1-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for a number of manufacturer-specific registers in the
debugfs entries, as well as support to read and write the
PMBUS_ON_OFF_CONFIG register through debugfs.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1576788607-13567-2-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If a chip is write protected, we can not change any limits, and we can
not clear status flags. This may be the reason why clearing status flags
is reported to not work for some chips. Detect the condition in the pmbus
core. If the chip is write protected, set limit attributes as read-only,
and set the flag indicating that the status flag should be ignored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some systems may plug in either version 1 or version 2 of the IBM common
form factor power supply. Add a version-less compatibility string that
tells the driver to try and detect which version of the power supply is
connected.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1570648262-25383-3-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LED blink_set function incorrectly did not tell the PSU LED to blink
if brightness was LED_OFF. Fix this, and also correct the LED_OFF
command data, which should give control of the LED back to the PSU
firmware. Also prevent I2C failures from getting the driver LED state
out of sync and add some dev_dbg statements.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20191106200106.29519-3-eajames@linux.ibm.com
Fixes: ef9e1cdf41 ("hwmon: (pmbus/cffps) Add led class device for power supply fault led")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_smbus functions can sleep, the brightness setting function
for this driver must be the blocking version to avoid scheduling while
atomic.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20191106200106.29519-2-eajames@linux.ibm.com
Fixes: ef9e1cdf41 ("hwmon: (pmbus/cffps) Add led class device for power supply fault led")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Version 2 of the PSU supports a second page of data and changes the
format of the FW version. Use the devicetree binding to differentiate
between the version the driver should use.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/1567192263-15065-4-git-send-email-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor Inspur Power System power supplies
with hwmon over pmbus.
This driver adds sysfs attributes for additional power supply data,
including vendor, model, part_number, serial number,
firmware revision, hardware revision, and psu mode(active/standby).
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190819091509.29276-1-wangzqbj@inspur.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is a typo in MAX37185_NUM_FAN_PAGES. To be consistent, it should be
MAX31785_NUM_FAN_PAGES (1 and 7 switched).
At line 24, we already have:
#define MAX31785_NR_FAN_PAGES 6
and MAX37185_NUM_FAN_PAGES seems to be unused.
It is likely that it is only a typo and/or a left-over.
So, axe it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20190721101553.20911-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Build bot reports the following build issue after commit 9091373ab7
("gpio: remove less important #ifdef around declarations):
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:576:1: error: redefinition of 'gpiochip_add_pin_range'
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:245:1: note: previous definition of 'gpiochip_add_pin_range' was here
gpiochip_add_pin_range(struct gpio_chip *chip, const char *pinctl_name,
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:583:1: error: redefinition of 'gpiochip_add_pingroup_range'
gpiochip_add_pingroup_range(struct gpio_chip *chip,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:254:1: note: previous definition of 'gpiochip_add_pingroup_range' was here
gpiochip_add_pingroup_range(struct gpio_chip *chip,
^~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:19:0:
>> include/linux/gpio/driver.h:591:1: error: redefinition of 'gpiochip_remove_pin_ranges'
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/hwmon/pmbus/ucd9000.c:18:0:
include/linux/gpio.h:263:1: note: previous definition of 'gpiochip_remove_pin_ranges' was here
gpiochip_remove_pin_ranges(struct gpio_chip *chip)
This is caused by conflicting defines from linux/gpio.h and
linux/gpio/driver.h. Drivers should not include both the legacy and
the new API headers. This driver doesn't even use linux/gpio.h so
remove it.
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190808080144.6183-1-brgl@bgdev.pl
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not every chip supported by this driver supports setting the number
of samples for power averaging. Also, the power monitoring register
is not always a 16-bit register, and the configuration bits used for
voltage sampling are different depending on the register width.
Some conditional code is needed to fix the problem.
On top of all that, the compiler complains about problems with
FIELD_GET and FIELD_PREP macros if the file is built with W=1.
Avoid using those macros to silence the warning.
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a driver to support the Infineon IRPS5401 PMIC. This chip has 5
pages corresponding to 4 switching outputs and one linear (LDO) output.
The switching and LDO outputs have slightly different supported
parameters.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Added pmbus driver for the new device Infineon pxe1610
voltage regulator. It also supports similar family device
PXE1110 and PXM1310.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The device supports setting the number of samples for averaging the
measurements. There are two separate settings - PWR_AVG for averaging
PIN and VI_AVG for averaging VIN/VAUX/IOUT, both being part of
PMON_CONFIG register. The values are stored as exponent of base 2 of the
actual number of samples that will be taken.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[groeck: Dropped unused variables]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some chips have attributes which exist on more than one page but the
attribute is not presently marked as paged. This causes the attributes
to be generated with the same label, which makes it impossible for
userspace to tell them apart.
Marking all such attributes as paged would result in the page suffix
being added regardless of whether they were present on more than one
page or not, which might break existing setups. Therefore, we add a
second check which treats the attribute as paged, even if not marked as
such, if it is present on multiple pages.
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
update_lock is a mutex intended to protect write operations. It was not
taken, however, when _pmbus_write_word_data is called from
pmbus_set_samples() function which may cause problems especially when
some PMBUS_VIRT_* operation is implemented as a read-modify-write cycle.
This patch makes sure the lock is held during the operation.
Fixes: 49c4455dcc ("hwmon: (pmbus) Introduce PMBUS_VIRT_*_SAMPLES registers")
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[groeck: Declared and initialized missing 'data' variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 441 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520071858.739733335@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intersil ISL68137 is a digital output 7-phase configurable PWM
controller with an AVSBus interface.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch makes it possible to pass custom struct attribute_group array
via the pmbus_driver_info struct so that those can be added to the
attribute groups passed to hwmon_device_register_with_groups().
This makes it possible to register custom sysfs attributes by PMBUS
drivers similar to how you can do this with most other busses/classes.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Manufacturer specific SAMPLES_FOR_AVG register allows setting the number
of samples used in computing the average values (PMBUS_VIRT_READ_*_AVG).
The number we write is an exponent of base 2 of the number of samples so
for example writing 3 will result in 8 samples average.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Those virtual registers can be used to export manufacturer specific
functionality for controlling the number of samples for average values
reported by the device.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace S_<PERMS> with octal values.
The conversion was done automatically with coccinelle. The semantic patches
and the scripts used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches/.
This patch does not introduce functional changes. It was verified by
compiling the old and new files and comparing text and data sizes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the pmbus driver for the Infineon ir38064 voltage regulator.
VOUT_MODE is not supported by the device. The driver fakes linear16
mode with exponent value -8.
The device supports VOUT_PEAK, IOUT_PEAK, and TEMPERATURE_PEAK, however
this driver does not enable them.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If CONFIG_OF is not enabled, the following build warning is observed.
drivers/hwmon/pmbus/ucd9000.c:154:34: warning:
‘ucd9000_of_match’ defined but not used
Mark ucd9000_of_match as __maybe_unused to fix the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Grant Peltier