When a skb is delivered to a registered callback, cn_call_callback()
incorrectly returns -ENODEV after freeing the skb, causing cn_rx_skb()
to free the skb a second time.
Reported-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace relpy with reply.
replace premanent with permanent.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace tranmitted with transmitted.
replace tranmitting with transmitting.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, alb_bond_info uses rx_ntt,rlb_update_delay_counter and
rlb_update_retry_counter to decide when to call rlb_update_rx_clients().
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now bonding-alb uses delayed_work instead of timer_list.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some old MAC chips without COE sometime the
Transmit Underflow error is issued.
The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.
The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: Nachiketa Prachanda <nprachanda@ncomputing.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a compilation error when build the
dwmac_lib with the DEBUG option enabled.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, IWLWIFI_LEGACY has to be selected independently before the
drivers are made available.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In commit 13583b1659 ("PCI: refactor io size calculation code") Ram
had a thinko in the refactorization of the code: the end result used the
variable 'align' for the bus alignment, but the original code used
'min_align'.
Since then, another use of that 'align' variable got introduced by
commit c8adf9a3e8 ("PCI: pre-allocate additional resources to devices
only after successful allocation of essential resources.")
Fix both of those uses to use 'min_align' as they should.
Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB
ethernet controllers to the existing smsc95xx driver by adding
their new USB VID/PID pairs.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/mtd-2.6:
mtd: atmel_nand: use CPU I/O when buffer is in vmalloc(ed) region
mtd: atmel_nand: modify test case for using DMA operations
mtd: atmel_nand: fix support for CPUs that do not support DMA access
mtd: atmel_nand: trivial: change DMA usage information trace
mtd: mtdswap: fix printk format warning
This patch fixes a very serious off-by-one bug in
the driver, which could leave the device in an
unresponsive state.
The problem was that the extra_len variable [used to
reserve extra scratch buffer space for the firmware]
was left uninitialized. Because p54_assign_address
later needs the value to reserve additional space,
the resulting frame could be to big for the small
device's memory window and everything would
immediately come to a grinding halt.
Reference: https://bugs.launchpad.net/bugs/722185
Cc: <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jason Conti <jason.conti@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If not done, second attempt to open the RX ring would cause memory corruption.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing the port up, performing a SENSE_PORT command
To try and check to which physical link type (IB or Ethernet) the physical
port is connected.
In case there is no valid link partner, the port will come up as its
supported default.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 1c48a5c93d (dt: Eliminate of_platform_{,un}register_driver)
mpc8xxx_wdt no longer builds as it tries to refer to a 'match' variable
rather than ofdev->dev.of_match that it checks just before.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
efifb: Add override for 11" Macbook Air 3,1
efifb: Support overriding fields FW tells us with the DMI data.
fb: Reduce priority of resource conflict message
savagefb: Remove obsolete else clause in savage_setup_i2c_bus
savagefb: Set up I2C based on chip family instead of card id
savagefb: Replace magic register address with define
drivers/video/bfin-lq035q1-fb.c: introduce missing kfree
video: s3c-fb: fix checkpatch errors and warning
efifb: support AMD Radeon HD 6490
s3fb: fix Virge/GX2
fbcon: Remove unused 'display *p' variable from fb_flashcursor()
fbdev: sh_mobile_lcdcfb: fix module lock acquisition
fbdev: sh_mobile_lcdcfb: add blanking support
viafb: initialize margins correct
viafb: refresh rate bug collection
sh: mach-ap325rxa: move backlight control code
sh: mach-ecovec24: support for main lcd backlight
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
Joe Culler reported a problem with his AR9170 device:
> ath: EEPROM regdomain: 0x5c
> ath: EEPROM indicates we should expect a direct regpair map
> ath: invalid regulatory domain/country code 0x5c
> ath: Invalid EEPROM contents
It turned out that the regdomain 'APL7_FCCA' was not mapped yet.
According to Luis R. Rodriguez [Atheros' engineer] APL7 maps to
FCC_CTL and FCCA maps to FCC_CTL as well, so the attached patch
should be correct.
Cc: <stable@kernel.org>
Reported-by: Joe Culler <joe.culler@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the mwl8k driver attempts and fails to switch from sta to ap
firmware (or vice-versa) in the mwl8k_add_interface routine, the
mwl8k_stop routine will be called. This routine must not attempt
to free the irq if it was not requested.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At least EEPROM version 0x11A has the wrong
number of chains programmed into it for some
reason, so we need to override in the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.infradead.org/ubifs-2.6:
UBI: do not select KALLSYMS_ALL
UBI: do not compare array with NULL
UBI: check if we are in RO mode in the erase routine
UBIFS: fix debugging failure in dbg_check_space_info
UBIFS: fix error path in dbg_debugfs_init_fs
UBIFS: unify error path dbg_debugfs_init_fs
UBIFS: do not select KALLSYMS_ALL
UBIFS: fix assertion warnings
UBIFS: fix oops on error path in read_pnode
UBIFS: do not read flash unnecessarily
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for CH Pro Throttle
HID: hid-magicmouse: Increase evdev buffer size
HID: add FF support for Logitech G25/G27
HID: roccat: Add support for wireless variant of Pyra
HID: Fix typo Keyoutch -> Keytouch
HID: add support for Skycable 0x3f07 wireless presenter
Fix build failure issue for hv_mouse
When build 2.6.39-rc1 kernel, it will be blocked at build hv_mouse.
drivers/staging/hv/hv_mouse.c: In function ‘ReleaseInputDevice’:
drivers/staging/hv/hv_mouse.c:293: error: implicit declaration of function ‘udelay’
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit f44f7f96a2 ("RTC: Initialize kernel state from RTC") caused a
boot regression on the MRST platform.
The reason is that rtc_device_register() calls rtc_read_alarm() after
that change, which function does not have all driver data set up yet.
The rtc-mrst driver needs to call dev_set_drvdata() before rtc_device_register()
gets called.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302140384-27571-1-git-send-email-feng.tang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For isochronous packets the actual_length is the sum of the actual
length of each of the packets, however between the packets might be
padding, so it is not sufficient to just send the first actual_length
bytes of the buffer. To fix this and simultanesouly optimize the
bandwidth the content of the isochronous packets are send without the
padding, the padding is restored on the receiving end.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The number_of_packets was not transmitted for RET_SUBMIT packets. The
linux client used the stored number_of_packet from the submitted
request. The windows userland client does not do this however and needs
to know the number_of_packets to determine the size of the transmission.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When doing a usb port reset do a queued reset instead to prevent a
deadlock: the reset will cause the driver to unbind, causing the
usb_driver_lock_for_reset to stall.
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When shuting down the tcp_rx and tcp_tx threads first check if they are
not closed already (maybe because an error caused them to return).
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After Quick Migration, the network is not immediately operational in the
current context when receiving RNDIS_STATUS_MEDIA_CONNECT event. So, I added
another netif_notify_peers() into a scheduled work, otherwise GARP packet will
not be sent after quick migration, and cause network disconnection.
Thanks to Mike Surcouf <mike@surcouf.co.uk> for reporting the bug and
testing the patch.
Reported-by: Mike Surcouf <mike@surcouf.co.uk>
Tested-by: Mike Surcouf <mike@surcouf.co.uk>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Abhishek Kane <v-abkane@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
eq_next_idx is not getting reset to zero during suspend.
This causes resume to fail. Added the fix.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renamed msix_vec_idx to eq_idx in be_eq_obj struct.
Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure.
These members are used in INTX mode also.
Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise we loop forever if a PPPoE socket was set
to PPPOX_ZOMBIE state by a PADT message when the
ethernet device is going down afterwards.
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
adapter could remain uninitialized if probe fails for some reason.
A null pointer access could cause a crash if be_shutdown
is called after that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a fix for gracefully handling firmware heartbeat
failure instead of forcing panic.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interrupt occurs, the INT pin is driven low by the
MCP251x controller (falling edge) but in some cases the INT
pin can be connected to the MPU through a transistor or level
translator which inverts this signal. In this case interrupt
should be configured in rising edge.
This patch adds support to pass the IRQ flags via
mcp251x_platform_data.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SMSC911X_SAVE_MAC_ADDRESS flag is enabled the driver calls
smsc911x_mac_read and smsc911x_mac_read function without acquiring mac_lock
spinlock
This patch fixes following warning
smsc911x: Driver version 2008-10-21.
------------[ cut here ]------------
WARNING: at drivers/net/smsc911x.c:261 smsc911x_mac_read+0x24/0x220()
Modules linked in:
[<c0060858>] (unwind_backtrace+0x0/0xe0) from [<c009322c>] (warn_slowpath_common+0x4c/0x64)
[<c009322c>] (warn_slowpath_common+0x4c/0x64) from [<c009325c>] (warn_slowpath_null+0x18/0x1c)
[<c009325c>] (warn_slowpath_null+0x18/0x1c) from [<c0324bec>] (smsc911x_mac_read+0x24/0x220)
[<c0324bec>] (smsc911x_mac_read+0x24/0x220) from [<c0434788>] (smsc911x_read_mac_address+0x18/0x6c)
[<c0434788>] (smsc911x_read_mac_address+0x18/0x6c) from [<c0434c74>] (smsc911x_drv_probe+0x498/0x1788)
[<c0434c74>] (smsc911x_drv_probe+0x498/0x1788) from [<c02d3e54>] (platform_drv_probe+0x14/0x18)
[<c02d3e54>] (platform_drv_probe+0x14/0x18) from [<c02d2d60>] (driver_probe_device+0xc8/0x184)
[<c02d2d60>] (driver_probe_device+0xc8/0x184) from [<c02d2e84>] (__driver_attach+0x68/0x8c)
[<c02d2e84>] (__driver_attach+0x68/0x8c) from [<c02d1fc8>] (bus_for_each_dev+0x48/0x74)
[<c02d1fc8>] (bus_for_each_dev+0x48/0x74) from [<c02d2660>] (bus_add_driver+0x9c/0x228)
[<c02d2660>] (bus_add_driver+0x9c/0x228) from [<c02d3598>] (driver_register+0xa0/0x124)
[<c02d3598>] (driver_register+0xa0/0x124) from [<c0050668>] (do_one_initcall+0x94/0x168)
[<c0050668>] (do_one_initcall+0x94/0x168) from [<c0008984>] (kernel_init+0xa0/0x154)
[<c0008984>] (kernel_init+0xa0/0x154) from [<c005afac>] (kernel_thread_exit+0x0/0x8)
---[ end trace 2c931a35b7885770 ]---
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 11" Macbook Air appears to claim that its stride is 1366, when it's
actually 2048. Override it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Otavio Salvador