1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some DVB-T cards with Grundig 29504-401 tuner use subsystem id 13c2:0001
(reported by Stuart Butterfield).
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hardware algorithm needs to be configured to:
1) Increase timeout constants, to detect weaker signals;
2) do a wider zigzag search.
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested on x64 with a bttv board. Most Get ioctls are fixed. The only
non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the
same results on x86_64 and i386 architectures.
Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this
patch and tests on ppc64.
Signed-off-by: Alastair Poole <netstar@gatheringofgray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed and commented a small debug function.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VGA was not turned on after calling sleep. This lead to bad performance in difficult areas.
Signed-off-by: matthieu castet <castet.matthieu@free.fr>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Another stupid fix for attaching the DiB3000MC. == 0 instead of != 0.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DiB3000MC: set FE to NULL after being freed
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A new revision of the Avermedia A800 does not reenumerate after download the firmware.
Signed-off-by: Klaus Frahm <frahm@irsamc.ups-tlse.fr>
Signed-off-by: Martin Habbecke <M.Habbecke@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thomas Rokamp and others are reporting:
"I have now with success extracted a working firmware for the 93004 rev. C1A2."
This patch increments the firmware version to 2.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Flynn Marquardt found out that there is problem with the new dib3000mc-driver
when using with the real dib3000mc. It resulted in a segfault.
Fixed two things: use the correct I2C address and do not attach a tuner, when
the demod was previously failing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The first commit omitted the common-code and header-files.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A complete rewrite of the DiB3000MC/P driver has been done. It is now much more
easy to maintain and to get improvements inside.
Additionally the tuning time has been reduced and the usage of the driver is
much more understandable now.
Signed-off-by: Patrick Boettcher <pboettcher@dibcom.fr>
Signed-off-by: Francois KANOUNNIKOFF <fkanounnikoff@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
removing the dib3000-common-module. The common stuff is not common anymore - it will be only used by the 3000mb-driver.
A new 3000mc/p-driver will be added which will share common stuff with dib7000.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
new tuner api
minor fixes for tuning
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When debugging was disabled at lot of empty lines where printed anyway.
Reported by Rolf Ahrenberg and Sergei Haller.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some minor code cleanups and added the MT2060 to new v4l-dvb-build-system, preliminarily under dvb/frontends.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
+ Added support for the remote control shipped with the pen drive size
DVB-T receiver
[ID 10b8:0bc7 DiBcom DiBcom USB2.0 DVB-T reference design (MOD3000P)]
Signed-off-by: Sergei Haller <sergei@sergei-haller.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- AGC gain set to 3
- The tuning sequence has been changed to match the DibCom driver ( from I2C
spy captures )
- For LITE-ON adapters : The IF1 frequency is now tuned according to the
calibration values stored in EEPROM.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding the USB ids for the LeadTek clone of the STK3000P-ref-design.
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding the USB IDs to dibusb-mc.c for the Artec T14 USB Stick based on STK3000P reference design.
Thanks to Thomas Rabe testing.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- some coding style fixes for newly added mt2060
- moved agc-config from fixed values in dib3000mc to configurable ones
- whitespace clean-ups for usb-id-file
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- MT2060 tuner driver
- Added support for some USB DVB-T devices based on Dib3000P
Signed-off-by: Olivier DANET <odanet@caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Address another case where the test in dvb-pll to see if a tuner's
PLL responds when attaching may fail.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change this card to use HW ALGO tuning
Signed-off-by: Yeasah Pell <yeasah@schwide.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the bit error counter configuration to be the actual BER.
Originally it was reporting UCB.
Signed-off-by: Yeasah Pell <yeasah@schwide.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Set the Soft decision threshold properly for the specified FEC
Signed-off-by: Yeasah Pell <yeasah@schwide.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tda826x detection was (correctly) cleaned up earlier, but unfortunately
changing the number of received i2c messages from 2 -> 1 was missed. This
fixes it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a card with RDS capabilities.
RDS specifications didn't change from V4L1 to V4L2, so that part should be OK.
This patch changed the following stuff:
* The device can be opened multiple times. That's necessary because there are
at least a radio application and an RDS application (rdsd) that want to
open() the device.
* Added a poll() function. Every character device should have that, and rdsd
expects it as it uses select() on that file descriptor.
* Converted the ioctls to V4L2. MUTE is not implemented correctly as the
card doesn't seem to have a special bit for that. Probably there are a few
more ioctls that should at least return 0 or an error.
As I do not own such a card, I couldn't test anything. If there is anybody out
there who owns such an ancient card, please test and report.
I just checked that the code compiles.
Signed-off-by: Hans J. Koch <koch@hjk-az.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This was breaking the build if i2c was not previously set
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
As opposed to printk() at the moment, which will fill logs uselessly
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I missed one call during the dvb_attach() development.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the 0-byte write that precedes 2-byte read.
Move initialize the info field in the static tuner_ops definition, so
that it doesn't need to be done manually.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the necessary code and makefile infrastructure
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
TDA10086 is a new DVB-S demodulator
TDA826x is a DVB-S Silicon Tuner
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/radio/radio-sf16fmi.c: In function 'fmi_do_ioctl':
drivers/media/radio/radio-sf16fmi.c:147: warning: implicit declaration of function 'KERNEL_VERSION'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move the call to dst_attach into the dst_attach function to eliminate
problems caused with dvb_attach.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Yeasah Pell