Otherwise we print out spurious processes on unused rings in the error
state.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For reasons I can't claim to fully understand gen4 seems to require
backlight duty cycle setting after the backlight has been enabled, or
else black screen follows. I don't have documentation for the correct
sequence on gen4 either. Confirmed on Dell Latitude D630 and MacBook4,1.
This fixes a regression introduced by
commit b35684b8fa
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:13:41 2013 +0200
drm/i915: do full backlight setup at enable time
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75791
Reported-and-tested-by: mcy@lm7.fr
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79423
Reported-and-tested-by: Marc Milgram <mmilgram@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.14+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On certain platforms pixel_multiplier is read out in
.get_pipe_config(), but it also gets used to calculate the
pixel clock in intel_sdvo_get_config(). If the pipe is disable
but some SDVO outputs are active, we may end up dividing by zero
in intel_sdvo_get_config().
To avoid the problem simply check for zero pixel_multiplier and skip
the division. Another attempt at fixing this involved populating
pixel_multiplier to 1 even for disabled pipes, but that triggered a
WARN because SDVO_CMD_GET_CLOCK_RATE_MULT command failed and thus
encoder_pixel_multiplier was left at zero and didn't match
pipe_config->pixel_multiplier.
The "divide by pixel_multiplier" operation got introduced here:
commit 18442d0878
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 13 16:00:08 2013 +0300
drm/i915: Fix port_clock and adjusted_mode.clock readout all over
and it has caused a regression on certain machines since they would
hit the div-by-zero during resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76520
Cc: <stable@vger.kernel.org> # 3.13+
Tested-by: Tim Richardson <tim@tim-richardson.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It causes black screen on bootup and is approximately 100x slower than
running with FBC disabled, so the GPU runs at a high frequency for much
longer - completely contrary to the power saving claims. It also still
has mutex deadlocks in multi-head scenarios, which can lead to a
system/X lockup. These bugs were known before FBC was enabled by default
on Haswell and still have not been fixed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79716
Reported-and-tested-by: Jon Kristensen <info@jonkri.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[Jani: update subject to reflect the actual change]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
display rework fixes lots of displayport issues.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.
Instead, on the source side, we cut power to the lanes after having put
the sink into D3. Link training takes care of everything required to
bring it back again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts. This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing. For now, it'll just be used for some
DP improvements.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time. This will be used in
future patches.
The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.
We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock. It's about to become a lot more
likely to hit the races.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Re-uses the implementation's accessor functions rather than requiring
and init/fini implementation for each chipset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's really not a great deal this time due to me spending most of this window on Maxwell. But, here's the random bits and pieces that's currently queued.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (25 commits)
drm/gk208/gr: add missing registers to grctx init
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
drm/nv50-/mc: fix kms pageflip events by reordering irq handling order.
drm/nouveau/disp/nv04-nv40: abort scanoutpos query on vga analog.
drm/nv50-/kms: wait for enough ring space in crtc_prepare()
drm/nouveau/disp/dp: support training pattern 3
drm/nouveau/disp/dp: support aux read interval during link training
drm/gk104/gpio: fix incorrect interrupt register usage
drm/nouveau/core: punt all object state change messages to trace level
drm/nouveau/clk: allow end-user reclocking for nv40, nvaa, and nve0 clock types
drm/nouveau/fb: default NvMemExec to on, turning it off is used for debugging only
drm/nouveau/bios: fix a potential NULL deref in the PROM shadowing function
drm/nouveau/i2c: bump the i2c delay for the adt7473
drm/nouveau/therm/fan/tach: default to 2 pulses per revolution
drm/nvf0/device: enable video decoding engines on gk110/gk208
drm/nvf1/device: add support for 0xf1 (gk110b)
drm/nouveau/device: support for probing GK20A
drm/nouveau/graph: add GK20A support
drm/nouveau/graph: pad firmware code at load time
drm/nouveau/graph: enable when using external fw
...
Chris Wilson