Add the mfd core driver which supports touchscreen
and ADC.
With this patch we are only adding infrastructure to
support the MFD clients.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Again, resolve conflicts identical to how Tony did.
Conflicts:
arch/arm/mach-omap2/board-h4.c
arch/arm/mach-omap2/board-n8x0.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a platform driver for Versatile Express' "system
register" block. It's a random collection of registers providing
the following functionality:
- low level platform functions like board ID access; in order to
use those, the driver must be initialized early, either statically
or based on the DT
- config bus bridge via "system control" interface; as the response
from the controller does not generate interrupt (yet), the status
register is periodically polled using a timer
- pseudo GPIO lines providing MMC card status and Flash WP#
signal control
- LED interface for a set of 8 LEDs on the motherboard, with
"heartbeat", "mmc0" and "cpu0" to "cpu5" as default triggers
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Versatile Express platform has an elaborated configuration system,
consisting of microcontrollers residing on the mother- and
daughterboards known as Motherboard/Daughterboard Configuration
Controller (MCC and DCC). The controllers are responsible for
the platform initialization (reset generation, flash programming,
FPGA bitfiles loading etc.) but also control clock generators,
voltage regulators, gather environmental data like temperature,
power consumption etc. Even the video output switch (FPGA) is
controlled that way.
Those devices are _not_ visible in the main address space and
the usual communication channel uses some kind of a bridge in
the peripheral block sending commands (requests) to the
controllers and receiving responses. It can take up to
500 microseconds for a transaction to be completed, therefore
it is important to provide a non-blocking interface to it.
This patch adds an abstraction of this infrastructure. Bridge
drivers can register themselves with the framework. Then,
a driver of a device can request an abstract "function" - the
request will be redirected to a bridge referred by thedd
"arm,vexpress,config-bridge" property of the device tree node.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
To be able to use SPARSE_IRQ while yet not using device tree,
we need to use irq_domain_add_simple() that will allocate
descriptors for the IRQs in the non-DT case, and fall back
to using the linear irqdomain in the DT case.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To be able to use SPARSE_IRQ while yet not using device tree,
we need to use irq_domain_add_simple() that will allocate
descriptors for the IRQs in the non-DT case, and fall back
to using the linear irqdomain in the DT case.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This function needs to be exported to let clients be able to
request the ape opp 100 voltage.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can move menelaus.h to live with other mfd headers to
get it out of plat for ARM common zImage support.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic, and
chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable specific
regulators;
5. Random fixes and cleanups for other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=LkdH
-----END PGP SIGNATURE-----
Merge tag 'for-v3.7' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"1. New drivers:
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic,
and chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable
specific regulators;
5. Random fixes and cleanups for other drivers."
Fix up trivial conflicts in <linux/mfd/88pm860x.h>
* tag 'for-v3.7' of git://git.infradead.org/battery-2.6: (52 commits)
pda_power: Remove ac_draw_failed goto and label
charger-manager: Add support sysfs entry for charger
charger-manager: Support limit of maximum possible
charger-manager: Check fully charged state of battery periodically
lp8727_charger: More pure cosmetic improvements
lp8727_charger: Fix checkpatch warning
lp8727_charger: Add description in the private data
lp8727_charger: Fix a typo - chg_parm to chg_param
lp8727_charger: Make some cosmetic changes in lp8727_delayed_func()
lp8727_charger: Clean up lp8727_charger_changed()
lp8727_charger: Return if the battery is discharging
lp8727_charger: Make lp8727_charger_get_propery() simpler
lp8727_charger: Make lp8727_ctrl_switch() inline
lp8727_charger: Make lp8727_init_device() shorter
lp8727_charger: Clean up lp8727_is_charger_attached()
lp8727_charger: Use specific definition
lp8727_charger: Clean up lp8727 definitions
lp8727_charger: Use the definition rather than enum
lp8727_charger: Fix code for getting battery temp
lp8727_charger: Clear interrrupts at inital time
...
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
The initilization of GPADC is moved from core driver to touch driver
with DT support.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use irqdomain and allocating interrupts. It's necessary for supporting
DT mode.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
These were submitted as bug fixes before v3.6 but not considered important
enough to be included in it. Some of them cross over to cleanup territory
as well, and aren't strictly bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO1wAAoJEIwa5zzehBx38h8P/3K6wurO/3mA/Bct6vA3eJcT
9vqZ3zSEVewsF+IXIxs2F0aw2YYFUTrQ0OlLvHzYDUGB5TwYqRjbG1UR/RHiEQwD
o3dS50rq5hIXeyw46cProEK4N1vnaiI2lVH/X6B+qfABbgS094EDBc8IQU0eDABb
M0yuIMnQTfDH+JqVVO8d5m36oAwQ6ADzBRNE4l2V4jkCj4wtXFfOlMyHLBtWx2fy
jWgPA9KYB1agIJ7RuVaS4/+7XK6QJJpltinlxNaQbxYt+CofqDA1dE/r846Jm7L9
71sGo1PFhZolIsM4H70vf496hFMhzxxBupInKTERMMKZl36fwbndf3wrzGttfLRx
B7o0fLUCzoC4ePBwZ8N532h9h70UcNNebZCxN7XD66UhochqB/e9hJHWsdZkOJos
Qnsu5LiB7PfJYLlUgtvZ9W0S5D9QpjtoN9r3BMGg59F00Z2jGR54L9vGf46T1FlS
GiPLPCB+tggRAsdZXJG7qkLncPINqUXmbtgT2p1ySrI9tCzJ/lfmZ3c8dBwJtVRM
bOY+Hfwx2z7YgfVp8VtwK2wD2bOv0NRmxR+L/fTsVU5MZmS1e4TsL8figPjnakb8
ZXqZEQhv1CWmYlif3nORfg4v65/NGh4+nw1618QwsS1tBbP705bUc7zVQ9hzk4IZ
lHnQka17gG5eIaZIO0Au
=bWnd
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM soc bug fixes from Olof Johansson:
"These were submitted as bug fixes before v3.6 but not considered
important enough to be included in it. Some of them cross over to
cleanup territory as well, and aren't strictly bugfixes."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: nomadik: remove NAND_NO_READRDY use
ARM: pxa: fix return value check in pxa2xx_drv_pcmcia_probe()
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
ARM: ep93xx: Move ts72xx.h out of include/mach
ARM: ep93xx: use __iomem pointers for MMIO
ARM: msm: Fix early debug uart mapping on some memory configs
ARM: msm: io: Change the default static iomappings to be shared
ARM: msm: io: Remove 7x30 iomap region from 7x00
ARM: msm: Remove call to missing FPGA init on 8660
ARM: OMAP4: wakeupgen: remove duplicate AUXCOREBOOT* read/write
ARM: OMAP4: wakeupgen: Fix the typo in AUXCOREBOOT register save
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
...
ports to the framework along with one MIPS port, one MFD port, one minor
framework enhancement and one helper function for platforms expressing
their clock data through device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7v8L
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clk framework update from Michael Turquette:
"The common clk framework changes for 3.7 are dominated by ARM platform
ports to the framework along with one MIPS port, one MFD port, one
minor framework enhancement and one helper function for platforms
expressing their clock data through device tree."
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: add of_clk_src_onecell_get() support
clk: ux500: Define smp_twd clock for u8500
mfd: dbx500: Provide a more accurate smp_twd clock
clk: ux500: Support for prmcu_rate clock
clk: Provide option for clk_get_rate to issue hw for new rate
clock: max77686: Add driver for Maxim 77686 32Khz crystal oscillator.
ARM: ux500: Switch to use common clock framework
clk: ux500: Clock definitions for u8500
clk: ux500: First version of clock definitions for ux500
clk: ux500: Adapt PRCMU and PRCC clocks for common clk
clk: versatile: make config option boolean
clk: add Loongson1B clock support
arm: mmp: make all SOCs use common clock by default
clk: mmp: add clock definition for mmp2
clk: mmp: add clock definition for pxa910
clk: mmp: add clock definition for pxa168
clk: mmp: add mmp specific clocks
clk: convert ARM RealView to common clk
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
- Support for putting regulators into bypass mode where they simply
switch their input to the output (mainly used for low power retention).
- A new API for setting voltages based on a voltage plus tolerance
rather than an explicit voltage range.
- Lots of cleanups and API updates from Axel Lin.
- New driver for MAX8907.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Kg66
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
- Support for putting regulators into bypass mode where they simply
switch their input to the output (mainly used for low power
retention).
- A new API for setting voltages based on a voltage plus tolerance
rather than an explicit voltage range.
- Lots of cleanups and API updates from Axel Lin.
- New driver for MAX8907.
* tag 'regulator-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (71 commits)
regulator: arizona-ldo: Remove top voltage
regulator: tps6586x: remove regulator-compatible from DT docs
regulator: tps65217.txt: remove regulator-compatible from DT docs
regulator: deprecate regulator-compatible DT property
regulator: fan53555: remove vsel_max not used
regulator: aat2870: Don't explicitly initialise the first field
extcon: arizona: Use bypass mode for MICVDD
regulator: wm831x-ldo: Add bypass support
regulator: arizona-micsupp: Support get/set bypass
regulator: arizona-ldo: Support get/set bypass
regulator: core: Provide regmap get/set bypass operations
regulator: core: Support bypass mode
regulator: Fairchild fan53555 support
regulator: twl: Remove another unused variable warning
regulator: core: Try using the parent device for the default regmap
regulator: core: Fast path non-deferred disables
regulator: core: Report microvolts in sysfs even with only list_voltage()
regulator: tps6586x: add support for SYS rail
regulator: lp872x: remove unnecessary function
regulator: lp872x: fix NULL pointer access problem
...
smsc ece1099 is a keyboard scan or gpio expansion device.
The patch create keypad and gpio expander child for this
multi function smsc driver.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the DA9055 MFD core driver that instantiate all the dependent
component drivers and provides them the device access via I2C.
This patch is functionally tested on Samsung SMDK6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
commit 0848c94fb4 ("mfd: core: Push irqdomain mapping out into devices")
that appeared in v3.6-rc6 adds another argument to the mfd_add_devices()
call, and that makes commit a830d28b48 ("power_supply: Enable
battery-charger for 88pm860x", which is battery tree) no longer compatible
with the latest kernels.
This commit is used to merge upstream back into battery tree and
accommodate 88pm860x driver for the latest changes in MFD core.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
mfd: Add backlight as subdevice to the tps65217
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The PRCMU has its own USB, Thermal, GPIO, Modem, HSI and RTC drivers,
amongst other things. This patch allows those subordinate devices to
use it as an interrupt controller as and when they are DT enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes:
drivers/mfd/max8907.c:179:16: sparse: symbol 'max8907_pm_off' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TI LP8788 PMU provides regulators, battery charger, ADC,
RTC, backlight driver and current sinks.
This MFD patch supports the I2C communication using the regmap,
the interrupt handling using the linear IRQ domain and
configurable platform data structures for each driver module.
(Driver Architecture)
< mfd devices >
LP8788 HW .......... mfd .......... regulator drivers
I2C power supply driver
IRQs iio adc driver
rtc driver
backlight driver
current sink drivers
o regulators : LDOs and BUCKs
o power supply : Battery charger
o iio adc : Battery voltage/temperature
o rtc : RTC and alarm
o backlight
o current sink : LED and vibrator
All MFD device modules are registered by LP8788 MFD core driver.
For sharing information such like the virtual IRQ number,
MFD core driver uses the resource structure.
Then each module can retrieve the specific IRQ number and detect it
in the IRQ thread.
Configurable platform data is handled in each driver module.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The local timer clock is based on ARM subsystem clock. This patch
obtains a more exact value of that clock by reading PRCMU registers.
Using this increases the accuracy of the local timer events.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Two variables named master_int and sleepseq_val, were just
declared without initialization. Pointers to these variables
were passed to mfd read function. After that these variables
were used for some of the logical operations.
Though logically there is nothing wrong, compiler is complaining
that the variables may be used uninitialized.
Hence fixing these warning messages by initializing them.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add device tree handling to the palmas MFD. This takes the values
that can be set from platform data from the device tree nodes instead.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add the platform data and data structures for children that shall be
added by a future set of commits.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Swith the palmas to linear domain in all cases so in future DT and non
DT cases will work the same.
With this patch children no longer need IRQ resources as it's easier
for them to use regmap_get_virq. So we can remove the resources
definitions.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Improve the error exit path so that we correctly de-allocate resources
that have been allocated upto the point where error occurs.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide a compatible string for the AB8500 CODEC to aid in
configuration property look-up from its associated Device Tree
node.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
commit e7c706b1e5 migrated the allocation
of struct mc13xxx to devm_* functions, but left a kfree(mc13xxx) in the
mc13xxx_common_init error path. Remove it to prevent memory corruption.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Thanks to Julia Lawall <julia.lawall@lip6.fr> for automating the conversion
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TLL specific code such as channels clocks enable/disable,
initialization functions are removed from the USBHS core
driver. The hwmod of the usb tll is retrieved and omap device
build is performed to created the platform device for the
usb tll component.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The usbhs driver invokes the enable/disable APIs of the
usb tll driver in the runtime resume/suspend callbacks
of the runtime get sync and put sync of the usbhs driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The platform driver for the TLL component of the OMAP USB host controller
is implemented. Depending on the TLL hardware revision , the TLL channels
are configured. The USB HS core driver uses this driver through exported
APIs from the TLL platform driver.
usb_tll_enable and usb_tll_disble are the exported APIs of the USB TLL
platform driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Sparse complains:
CHECK drivers/power/88pm860x_battery.c
drivers/power/88pm860x_battery.c:128:5: warning: symbol 'array_soc' was not declared. Should it be static?
CHECK drivers/power/88pm860x_charger.c
drivers/power/88pm860x_charger.c:640:3: warning: symbol 'pm860x_irq_descs' was not declared. Should it be static?
CHECK drivers/mfd/88pm860x-core.c
drivers/mfd/88pm860x-core.c:803:53: warning: incorrect type in assignment (different base types)
drivers/mfd/88pm860x-core.c:803:53: expected struct charger_regulator *charger_regulators
drivers/mfd/88pm860x-core.c:803:53: got struct regulator_bulk_data static [toplevel] *
The issues are minor, except for the last one. We seemed to use
'regulator_bulk_data' struct (just as charger manager documentation
wrongly tells us), but in real it should have been
'struct charger_regulator'. The only reason that it worked is
because both 'supply' and 'regulator_name' struct members are the
first in these structs. :-)
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
There are charger and battery measurement feature for 88pm860x PMIC.
For charger, it can support pre-charge with small current when battery is
nearly exausted and then changed into fast-charge with CC&CV mode.
For battery monitor, it can support battery measurement such as
vbat,vsys,vchg and ibat etc,it can aslo accumulating the Coulomb value
charged or discharged from battery based on Conlomb Counter, we use it
to estimate battery capacity.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fzT6
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
Move probe() and other functions from 88pm860x-i2c.c to 88pm860x-core.c.
Since it could benefit to handle DT information.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since PREG regulator is the only one regulator in 88PM8606, and other
regulators are in 88PM8607. Checking resource as identifying regulator
is not a good way. We can use NULL resource to indentify PREG regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove array in parent's platform data. Use struct regulator_init_data
as regulator device's platform data directly. So a lot of pdata are
added into parent's platform data. And voltage out register offset
is used as IORESOURCE_REG to distinguish different regualtor devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the register offset definition. All these register offset
are transfered as IORESOURCE_REG resources.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add needed platform data structure and code to be able to load
the GPO child of twl6040.
Update the devicetree binding documentation at the same time.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Make sure threaded IRQs without a primary handler are always request
with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "maxim,system-power-controller" to indicate whether the
PMIC is in charge of controlling the system power. If this is set, the
driver will provide the pm_power_off() function.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework. In order for this to work properly, register the PWM as
child of the multi-function TWL6030 device.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of reinventing macros for the same purpose, use the standard
macros.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
From Tony Lindgren:
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
* tag 'cleanup-fixes-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: Include gpio-omap.h for board-h2 and board-h3
ARM: OMAP2+: Enable pinctrl dummy states
mfd: Fix compile for twl-core.c by removing cpu_is_omap usage
Support for loading the twl4030 audio module via devicetree.
Sub devices for codec and vibra will be created as mfd devices once the
core MFD driver is loaded when the kernel is booted with a DT blob.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl-core has API to get the boot time configured HFCLK rate which has the
same rate as the audio MCLK.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
CFG_BOOT register's HFCLK_FREQ field hold information about the used HFCLK
frequency.
Add possibility for users to get the configured rate based on this
register.
This register was configured during boot, without it the chip would not
operate correctly, so we can trust on this information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To facilitate the device tree support the probe function need to be rearanged.
Small cleanup in the APLL frequency selection part as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To clean up the module probe and remove functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Place the MODULE_* lines in the same block and add MODULE_DESCRIPTION.
Rearange the platform_driver structure at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Before the AB8500 had its own IRQ domain, the IRQ handler would take
the fired local IRQ (hwirq) and add it to the irq_base to convert it
to an IRQ number which Linux would understand (virq). However, the
IRQ base is not always used anymore since we can make use of Linear
domains. It's better to use the AB8500 hwirq -> virq mapping helper
function to convert them instead. That's what we do here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal) broke
compile for non-omap as include plat/cpu.h was added. This header
was indirectly included earlier when SPARSE_IRQ was not set, but
does not exist on most platforms.
Fix the problem by removing the cpu_is_omap usage that should
not exist in drivers at all. We can do this by adding proper
clock aliases for the twl-core.c drivers, and drop separate
handling for cases when clock framework is not available as
the behaviour will stay the same.
Note that we need to add a platform device to avoid using the
i2c provided names that may be different on various omaps.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The anatop registers are accessed via syscon now, no one will use
mfd anatop driver anymore, remove it.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add regmap based syscon driver.
This is usually used for access misc bits in registers which does not belong
to a specific module, for example, IMX IOMUXC GPR and ANATOP.
With this driver, client can use generic regmap API to access registers
which are registered into syscon.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Here we provide a means to probe and extract vital information
from Device Tree when booting with it enabled. Without this
patch sub-devices wouldn't be able to reference the tc3589x
from Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for Device Tree enablement all IRQ controllers
should control their own IRQ domain. This patch provides just
that.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using kfree to free data allocated with devm_kzalloc causes double frees.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Converted to regmap-irq.
* Allowed probing from device tree.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com> #v3
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GLSh
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-sparseirq-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains changes needed to make omap2+
work properly with sparse IRQ. It also removes
dependencies to mach/hardware.h. These help moving
things towards ARM single zImage support.
This branch is based on a commit in tty-next
branch with omap-devel-gpmc-fixed-for-v3.7 and
cleanup-omap-tags-for-v3.7 merged in to keep things
compiling and sort out some merge conflicts.
* tag 'omap-cleanup-sparseirq-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: Move SoC specific headers from plat to mach for omap1
ARM: OMAP2+ Move SoC specific headers to be local to mach-omap2
ARM: OMAP: Split plat/hardware.h, use local soc.h for omap2+
ARM: OMAP: Remove unused old gpio-switch.h
ARM: OMAP1: Move plat/irqs.h to mach/irqs.h
ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ
ARM: OMAP2+: Prepare for irqs.h removal
W1: OMAP HDQ1W: Remove dependencies to mach/hardware.h
Input: omap-keypad: Remove dependencies to mach includes
ARM: OMAP: Move gpio.h to include/linux/platform_data
ARM: OMAP2+: Remove hardcoded twl4030 gpio_base, irq_base and irq_end
ARM: OMAP2+: Remove unused nand_irq for GPMC
ARM: OMAP2+: Make INTCPS_NR_IRQS local for mach-omap2/irq.c
ARM: OMAP1: Define OMAP1_INT_I2C locally
ARM: OMAP1: Move define of OMAP_LCD_DMA to dma.h
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to initialize the
watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device addition
API in order to prevent silent and potentially harmful remapping behaviour
changes for drivers supporting non-DT platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nP/y
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
This patch adds the Watchdog Timer Device IDs for the Intel Lynx Point-LP PCH.
The Device IDs are defined in drivers/mfd/lpc_ich.c
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.
This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fix bug related to interrupt handling for MAX77693 devices.
- Unmask interrupt masking bit for charger/flash/muic to revolve
that interrupt isn't happened when external connector is attached.
- Fix wrong regmap instance when muic interrupt is happened.
This patch were discussed and confirm discussion about this patch on below url:
http://lkml.org/lkml/2012/7/16/118
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the sa1100 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jochen Friedrich <jochen@scram.de>
The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
WARNING: drivers/built-in.o(.data+0x1e3c8): Section mismatch in
reference from the variable bk_devs to the variable
.devinit.data:bk0_resources
The variable bk_devs references
the variable __devinitdata bk0_resources
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the
variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one,
*_console
So add __devinitdata on bk_devs, led_devs & reg_devs.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add DT property "ti,system-power-controller" telling whether or not this
pmic is in charge of controlling the system power, so the power off
routine can be hooked up to system call "pm_power_off".
Based on the work by:
Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Bill Huang <bilhuang@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MFD core now takes care of HWIRQ <-> VIRQ mapping, so the helper
ab8500_irq_get_virq() is no longer used by ab8500 subordinate devices
to obtain a Linux wide Virtual IRQ. The AB8500 IRQ controller still
uses it internally though, so we'll just hide it from the rest of the
world by making it static instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The ICH chips have their GPIO pins organized in 2 or 3 independent
groups of 32 GPIO pins. It can happen that the ACPI BIOS wants to make
use of pins in one group, preventing the OS to access these. This does
not prevent the OS from accessing the other group(s).
This is the case for example on my Asus Z8NA-D6 board. The ACPI BIOS
wants to control GPIO 18 (group 1), while I (the OS) need to control
GPIO 52 and 53 (group 2) for SMBus multiplexing.
So instead of checking for ACPI resource conflict on the whole I/O
range, check on a per-group basis, and consider it a success if at
least one of the groups is available for the OS to use.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Left over as bitrot from previous changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Further evaluation of the device has yielded some improvements to the
device configuration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Higher cust_ids have had the device revision field reset so need different
handling of GPIO6.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can read back if the primary IRQ is asserted from the register map,
meaning that we can suppress polling of the interrupt status registers
when only the AoD IRQ domain is asserting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently the MFD core supports remapping MFD cell interrupts using an
irqdomain but only if the MFD is being instantiated using device tree
and only if the device tree bindings use the pattern of registering IPs
in the device tree with compatible properties. This will be actively
harmful for drivers which support non-DT platforms and use this pattern
for their DT bindings as it will mean that the core will silently change
remapping behaviour and it is also limiting for drivers which don't do
DT with this particular pattern. There is also a potential fragility if
there are interrupts not associated with MFD cells and all the cells are
omitted from the device tree for some reason.
Instead change the code to take an IRQ domain as an optional argument,
allowing drivers to take the decision about the parent domain for their
interrupts. The one current user of this feature is ab8500-core, it has
the domain lookup pushed out into the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
From "Uwe Kleine-Knig" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
As the interrupts should only be defined in the platform_data, and
eventually coming from device tree, there's no need to define them
in header files.
Let's remove the hardcoded references to irqs.h and fix up the includes
so we don't rely on headers included in irqs.h. Note that we're
defining OMAP_INTC_START as 0 to the interrupts. This will be needed
when we enable SPARSE_IRQ. For some drivers we need to add
#include <plat/cpu.h> for now until these drivers are fixed to
remove cpu_is_omapxxxx() usage.
While at it, sort som of the includes the standard way, and add
the trailing commas where they are missing in the related data
structures.
Note that for drivers/staging/tidspbridge we just define things
locally.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Early revisions of the initial Arizona-based devices can generate spurious
control interface errors in certain circumstances. Avoid causing confusion
by disabling the control interface error reporting on these devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since IORESOURCE_IO is changed to IORESOURCE_REG in 88pm860x driver,
update self-defined IORESOURCE_IO resource to register offset that
is IORESOURCE_REG in regulator driver. And split regulator platform
data array into scattered platform data.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the resources of 88pm860x leds are changed from IORESOURCE_IO
to IORESOURCE_REG that is register offset, change the original
self-defined IORESOURCE_IO to register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now resource of 88pm860x backlight is changed from IORESOURCE_IO
to IORESOURCE_REG. In original driver, the resource is using
self-defined IORESOURCE_IO. So change the resource to register
offset to match the definition of IORESOURCE_REG.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was originally written by Russell King who unfortunately found
himself unable to take the patch futher.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The removal of mach/io.h from most ARM platforms also set the range of
valid IO ports to be empty for most platforms when previously any 32
bit integer had been valid. This makes it impossible to add IO resources
as the added range is smaller than that of the root resource for IO ports.
Since we're not really using IO memory at all fix this by defining our
own root resource outside the normal tree and make that the parent of
all IO resources. This also ensures we won't conflict with read IO ports
if we ever run on a platform which happens to use them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.4+)
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The removal of mach/io.h from most ARM platforms also set the range of
valid IO ports to be empty for most platforms when previously any 32
bit integer had been valid. This makes it impossible to add IO resources
as the added range is smaller than that of the root resource for IO ports.
Since we're not really using IO memory at all fix this by defining our
own root resource outside the normal tree and make that the parent of
all IO resources. This also ensures we won't conflict with read IO ports
if we ever run on a platform which happens to use them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.4+)
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is possible since *of_device_id.data became const. While at it also
drop a cast to const that was never needed.
[ukl: split Arnd's patch by driver and add changlog]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The local timer clock is based on ARM subsystem clock. This patch
obtains a more exact value of that clock by reading PRCMU registers.
Using this increases the accuracy of the local timer events.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.
[swarren: Instantiate the sys regulator from board-harmony-power.c to
avoid regression.]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are many reports (including 2 of my machines) that iTCO_wdt watchdog
driver fails to be initialized in 3.5 kernel with error message like:
[ 5.265175] ACPI Warning: 0x00001060-0x0000107f SystemIO conflicts with Region \_SB_.PCI0.LPCB.TCOI 1 (20120320/utaddress-251)
[ 5.265192] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.265206] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
The root cause the iTCO_wdt driver in 3.4 probes the HW IO resource from
LPC's PCI config space, while in 3.5 kernel it relies on lpc_ich driver
for the probe, which adds a new acpi_check_resource_conflict() check, and
give up the probe if there is any conflict with ACPI.
Fix it by removing all the checks for iTCO_wdt to keep the same behavior as
3.4 kernel.
https://bugzilla.kernel.org/show_bug.cgi?id=44991
Actually the same check could be removed for the gpio-ich in lpc_ich.c,
but I'm not sure if it will cause problems.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Len Brown <len.brown@intel.com>
Cc: Bob Moore <robert.moore@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are many reports (including 2 of my machines) that iTCO_wdt watchdog
driver fails to be initialized in 3.5 kernel with error message like:
[ 5.265175] ACPI Warning: 0x00001060-0x0000107f SystemIO conflicts with Region \_SB_.PCI0.LPCB.TCOI 1 (20120320/utaddress-251)
[ 5.265192] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 5.265206] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
The root cause the iTCO_wdt driver in 3.4 probes the HW IO resource from
LPC's PCI config space, while in 3.5 kernel it relies on lpc_ich driver
for the probe, which adds a new acpi_check_resource_conflict() check, and
give up the probe if there is any conflict with ACPI.
Fix it by removing all the checks for iTCO_wdt to keep the same behavior as
3.4 kernel.
https://bugzilla.kernel.org/show_bug.cgi?id=44991
Actually the same check could be removed for the gpio-ich in lpc_ich.c,
but I'm not sure if it will cause problems.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Len Brown <len.brown@intel.com>
Cc: Bob Moore <robert.moore@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAyjj4ACgkQMUfUDdst+yn8gQCgkNpc92Ux5hBYJIX/AQYoBrTB
ktAAoLiXxIhVP+D4C42R1VLw9vGeB1QH
=+8kb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB patches from Greg Kroah-Hartman:
"Here are 10 more USB patches for 3.6-rc3. They all fix reported
problems (build problems for one of them, and easily repeatable oopses
for the others.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
gpu/mfd/usb: Fix USB randconfig problems
USB: CDC ACM: Fix NULL pointer dereference
USB: emi62: remove __devinit* from the struct usb_device_id table
USB: winbond: remove __devinit* from the struct usb_device_id table
USB: vt6656: remove __devinit* from the struct usb_device_id table
USB: rtl8187: remove __devinit* from the struct usb_device_id table
USB: p54usb: remove __devinit* from the struct usb_device_id table
USB: spca506: remove __devinit* from the struct usb_device_id table
USB: jl2005bcd: remove __devinit* from the struct usb_device_id table
USB: smsusb: remove __devinit* from the struct usb_device_id table
Fix config warning:
warning: ( ... && DRM_USB) selects USB which has unmet direct dependencies
(USB_SUPPORT && USB_ARCH_HAS_HCD)
and build error:
ERROR: "usb_speed_string" [drivers/usb/core/usbcore.ko] undefined!
by adding the missing dependency on USB_ARCH_HAS_HCD to DRM_UDL and DRM_USB.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:16: symbol USB_ARCH_HAS_OHCI depends on I2C
drivers/i2c/Kconfig:5: symbol I2C is selected by FB_DDC
drivers/video/Kconfig:86: symbol FB_DDC is selected by FB_CYBER2000_DDC
drivers/video/Kconfig:385: symbol FB_CYBER2000_DDC depends on FB_CYBER2000
drivers/video/Kconfig:373: symbol FB_CYBER2000 depends on FB
which is due to drivers/usb/Kconfig:
config USB_ARCH_HAS_OHCI
...
default y if ARCH_PNX4008 && I2C
Fix by dropping I2C from the above dependency; logic is that this is not a
platform dependency but a configuration dependency: the _architecture_ still
supports USB even is I2C is not selected.
This exposes:
drivers/video/Kconfig:36:error: recursive dependency detected!
drivers/video/Kconfig:36: symbol FB is selected by DRM_KMS_HELPER
drivers/gpu/drm/Kconfig:28: symbol DRM_KMS_HELPER is selected by DRM_UDL
drivers/gpu/drm/udl/Kconfig:1: symbol DRM_UDL depends on USB_ARCH_HAS_HCD
drivers/usb/Kconfig:78: symbol USB_ARCH_HAS_HCD depends on USB_ARCH_HAS_OHCI
drivers/usb/Kconfig:17: symbol USB_ARCH_HAS_OHCI depends on MFD_TC6393XB
drivers/mfd/Kconfig:396: symbol MFD_TC6393XB depends on GPIOLIB
drivers/gpio/Kconfig:35: symbol GPIOLIB is selected by FB_VIA
drivers/video/Kconfig:1560: symbol FB_VIA depends on FB
which can be fixed by having MFD_TC6393XB select GPIOLIB instead of depending on
it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The irq_to_gpio function was removed from the pxa platform
in linux-3.2, and this driver has been broken since.
There is actually no in-tree user of this driver that adds
this platform device, but the driver can and does get enabled
on some platforms.
Without this patch, building ezx_defconfig results in:
drivers/mfd/ezx-pcap.c: In function 'pcap_isr_work':
drivers/mfd/ezx-pcap.c:205:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
In commit 4f304245b "mfd: Set asic3 DS1WM clock_rate", a possible
path through asic3_mfd_probe was introduced that would lead to
an unpredictable return value, if everything succeeds but there
are pdata->leds is NULL. This was reported correctly by gcc.
Without this patch, building magician_defconfig results in:
drivers/mfd/asic3.c: In function 'asic3_mfd_probe':
drivers/mfd/asic3.c:940:2: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that is)
caught the issue and it was decided[1] that I'd just delay the battery
pull request, and then will fix it up by merging upstream back into
battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem was
needed to get rid of a warning in power supply subsystem (the warning
was not drivers/power's "fault", the thermal registration function just
needed a proper const annotation, which is also done by a small commit
on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=1NaS
-----END PGP SIGNATURE-----
Merge tag 'for-v3.6' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"The tag contains just a few battery-related changes for v3.6. It's is
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that
is) caught the issue and it was decided[1] that I'd just delay the
battery pull request, and then will fix it up by merging upstream back
into battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem
was needed to get rid of a warning in power supply subsystem (the
warning was not drivers/power's "fault", the thermal registration
function just needed a proper const annotation, which is also done by
a small commit on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28"
* tag 'for-v3.6' of git://git.infradead.org/battery-2.6: (23 commits)
thermal: Constify 'type' argument for the registration routine
olpc-battery: update CHARGE_FULL_DESIGN property for BYD LiFe batteries
olpc-battery: Add VOLTAGE_MAX_DESIGN property
charger-manager: Fix build break related to EXTCON
lp8727_charger: Move header file into platform_data directory
power_supply: Add min/max alert properties for CAPACITY, TEMP, TEMP_AMBIENT
bq27x00_battery: Add support for BQ27425 chip
charger-manager: Set current limit of regulator for over current protection
charger-manager: Use EXTCON Subsystem to detect charger cables for charging
test_power: Add VOLTAGE_NOW and BATTERY_TEMP properties
test_power: Add support for USB AC source
gpio-charger: Use cansleep version of gpio_set_value
bq27x00_battery: Add support for power average and health properties
sbs-battery: Don't trigger false supply_changed event
twl4030_charger: Allow charger to control the regulator that feeds it
twl4030_charger: Add backup-battery charging
twl4030_charger: Fix some typos
max17042_battery: Support CHARGE_COUNTER power supply attribute
smb347-charger: Add constant charge and current properties
power_supply: Add constant charge_current and charge_voltage properties
...
This merge is performed to take commit c56f5c0342 ("Thermal: Make
Thermal trip points writeable") out of Linus' tree and then fixup power
supply class. This is needed since thermal stuff added a new argument:
CC drivers/power/power_supply_core.o
drivers/power/power_supply_core.c: In function ‘psy_register_thermal’:
drivers/power/power_supply_core.c:204:6: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:154:29: note: expected ‘int’ but argument is of type ‘struct power_supply *’
drivers/power/power_supply_core.c:204:6: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:154:29: note: declared here
make[1]: *** [drivers/power/power_supply_core.o] Error 1
make: *** [drivers/power/] Error 2
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
Pull PWM subsystem from Thierry Reding:
"The new PWM subsystem aims at collecting all implementations of the
legacy PWM API and to eventually replace it completely.
The subsystem has been in development for over half a year now and
many drivers have already been converted. It has been in linux-next
for a couple of weeks and there have been no major issues so I think
it is ready for inclusion in your tree."
Arnd Bergmann <arnd@arndb.de>:
"Very much Ack on the new subsystem. It uses the interface
declarations as the previously separate pwm drivers, so nothing
changes for now in the drivers using it, although it enables us to
change those more easily in the future if we want to.
This work is also one of the missing pieces that are required to
eventually build ARM kernels for multiple platforms, which is
currently prohibited (amongs other things) by the fact that you cannot
have more than one driver exporting the pwm functions."
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Philip, Avinash <avinashphilip@ti.com> # TI's AM33xx platforms
Acked-By: Alexandre Pereira da Silva <aletes.xgr@gmail.com> # LPC32XX
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Fix up trivial conflicts with other cleanups and DT updates.
* 'for-3.6' of git://gitorious.org/linux-pwm/linux-pwm: (36 commits)
pwm: pwm-tiehrpwm: PWM driver support for EHRPWM
pwm: pwm-tiecap: PWM driver support for ECAP APWM
pwm: fix used-uninitialized warning in pwm_get()
pwm: add lpc32xx PWM support
pwm_backlight: pass correct brightness to callback
pwm: Use pr_* functions in pwm-samsung.c file
pwm: Convert pwm-samsung to use devm_* APIs
pwm: Convert pwm-tegra to use devm_clk_get()
pwm: pwm-mxs: Return proper error if pwmchip_remove() fails
pwm: pwm-bfin: Return proper error if pwmchip_remove() fails
pwm: pxa: Propagate pwmchip_remove() error
pwm: Convert pwm-pxa to use devm_* APIs
pwm: Convert pwm-vt8500 to use devm_* APIs
pwm: Convert pwm-imx to use devm_* APIs
pwm: Conflict with legacy PWM API
pwm: pwm-mxs: add pinctrl support
pwm: pwm-mxs: use devm_* managed functions
pwm: pwm-mxs: use global reset function stmp_reset_block
pwm: pwm-mxs: encode soc name in compatible string
pwm: Take over maintainership of the PWM subsystem
...
Pull embedded i2c changes from Wolfram Sang:
"Changes for the "embedded" part of the I2C subsystem:
- lots of devicetree conversions of drivers (and preparations for
that)
- big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
- Rafael's struct dev_pm_ops conversion patches for I2C
- usual driver cleanups and fixes
All patches have been in linux-next for an apropriate time and all
patches touching files outside of i2c-folders should have proper acks
from the maintainers."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
I2C: MV64XYZ: Add Device Tree support
i2c: stu300: use devm managed resources
i2c: i2c-ocores: support for 16bit and 32bit IO
V4L/DVB: mfd: use reg_shift instead of regstep
i2c: i2c-ocores: Use reg-shift property
i2c: i2c-ocores: DT bindings and minor fixes.
i2c: mv64xxxx: remove EXPERIMENTAL tag
i2c-s3c2410: Use plain pm_runtime_put()
i2c: s3c2410: Fix pointer type passed to of_match_node()
i2c: mxs: Set I2C timing registers for mxs-i2c
i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
i2c:i2c-bfin-twi: include twi head file
i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
i2c-mv64xxxx: allow more than one driver instance
...
Conflicts:
drivers/i2c/busses/i2c-nomadik.c
When booting via platform code the AB8500 platform data is now passed
in though the DB8500. However, if pdata_size is not set it will not be
subsequently passed onto subordinate devices. This patch correctly
populates pdata_size.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Otherwise, with:
CONFIG_MFD_ARIZONA=y
CONFIG_MFD_ARIZONA_I2C=m
CONFIG_MFD_CORE=m
We get:
drivers/built-in.o: In function `arizona_dev_init':
(.devinit.text+0x3ab0): undefined reference to `mfd_add_devices'
drivers/built-in.o: In function `arizona_dev_init':
(.devinit.text+0x3fdc): undefined reference to `mfd_add_devices'
drivers/built-in.o: In function `arizona_dev_init':
(.devinit.text+0x3fff): undefined reference to `mfd_add_devices'
drivers/built-in.o: In function `arizona_dev_init':
(.devinit.text+0x4059): undefined reference to `mfd_remove_devices'
drivers/built-in.o: In function `arizona_dev_exit':
(.devexit.text+0x9): undefined reference to `mfd_remove_devices'
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
arizona-irq.c uses functions that are only available when
CONFIG_REGMAP_IRQ is enabled, so select that symbol for
arizona builds.
Fixes these build errors:
arizona-irq.c:(.text+0xb2d47): undefined reference to `regmap_irq_get_virq'
(.text+0xb2fe3): undefined reference to `regmap_add_irq_chip'
(.text+0xb3173): undefined reference to `regmap_del_irq_chip'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There doesn't appear to be any useful diagnostic information from the
core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
mfd cell names are mistyped as TPS65910 instead of TPS65090.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The GPIO functionality of device tps6586x is added through
platform gpio driver and it can be register as the mfd sub
device and hence removing the duplicates code which register
the gpio functionality from core driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
To cache the interrupt mask register, use the regmap RB_TREE
cache-ing mechanism in place of implementing it locally.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using regmap apis for accessing the device registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allocate memory for device state using devm_kzalloc()
to simplify accounting and letting the kernel do the
garbage-collection.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The delta between twl6040 and twl6041 is small, the main difference is in
the number of GPOs (3 on twl6040, 1 on twl6041).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to avoid duplicate symbols with legacy PWM API implementations,
the new PWM framework needs to conflict with any of the existing legacy
implementations. This is done in two ways: for implementations provided
by drivers, a conflict is added to the driver to ensure it will have to
be ported to the PWM subsystem before it can coexist with other PWM
providers. For architecture-specific code, the conflict is added to the
PWM symbol to avoid confusion when a previously picked platform or
machine can no longer be selected because of the PWM subsystem being
included.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Samuel Ortiz <sameo@linux.intel.com>
With the new interrupt sampling system, we are no longer using the
timer_rand_state structure in the irq descriptor, so we can stop
initializing it now.
[ Merged in fixes from Sedat to find some last missing references to
rand_initialize_irq() ]
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
wm831x devices contain a unique ID value. Feed this into the newly added
device_add_randomness() to add some per device seed data to the pool.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace tps65910_misc_init with a dedicated init function for the
32-kHz-crystal input, and make the code more readable.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was introduced in commit
876989d (mfd: Add device tree probe support for mc13xxx)
for spi and later while introducing support for i2c copied to the i2c
driver.
Modifying driver details is very strange, for example probing an
mc13892 device (instantiated via dt) removes the driver's ability to
handle (traditionally probed) mc13783 devices in this case.
I'm not aware of any problems that make this hack necessary and if
there were some, they'd have to be fixed in the spi/i2c core, not in
a driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Current code has been converted to use regmap APIs, the io_mutex is not needed.
Thus remove the io_mutex.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes below section mismatch warning:
LD drivers/mfd/built-in.o
WARNING: drivers/mfd/built-in.o(.devinit.text+0x46c): Section mismatch in reference from the function pm800_probe() to the function .devexit.text:pm80x_deinit()
The function __devinit pm800_probe() references
a function __devexit pm80x_deinit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
pm80x_deinit() so it may be used outside an exit section.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Check the return value of regmap_read() rather than the read value.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM5110 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices. It combines an advanced DSP
feature set with a flexible, high-performance audio hub CODEC.
The support is based on the Arizona core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM5110 is a highly integrated low power audio subsystem for
smartphones, tablets and other portable audio devices. It combines
an advanced DSP feature set with a flexible, high performance audio
hub CODEC.
This patch adds data tables for the WM5110.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch support irq handling driver for s2mps11.
As this patch use regmap_irq, s5m8767 and s5m8763 are modified with
regmap_irq.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch add Samsung S2MPS11 mfd driver.
The S2MPS11 can support regulators and RTC.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As Prefix of Samsung pmic changed from s5m to s2m,
To make common mfd driver for s2m and s5m series,
This patch rename header of Samsung mfd and modify mfd driver.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previous naming rule of samsung pmic start with s5m prefix.
But It is changed by s2m.
To cover various samsung s2m and s5m series,
This patch modify function and variable name for common usage.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, Samsung PMIC naming rule start with prefix of s5m.
But Naming rule is changed.
From now on, Prefix will be changed to s2m.
So, To support pmic series of s5m and s2m, change mfd file and directory name.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We've been moving away from add_interrupt_randomness() for various
reasons: it's too expensive to do on every interrupt, and flooding the
CPU with interrupts could theoretically cause bogus floods of entropy
from a somewhat externally controllable source.
This solves both problems by limiting the actual randomness addition
to just once a second or after 64 interrupts, whicever comes first.
During that time, the interrupt cycle data is buffered up in a per-cpu
pool. Also, we make sure the the nonblocking pool used by urandom is
initialized before we start feeding the normal input pool. This
assures that /dev/urandom is returning unpredictable data as soon as
possible.
(Based on an original patch by Linus, but significantly modified by
tytso.)
Tested-by: Eric Wustrow <ewust@umich.edu>
Reported-by: Eric Wustrow <ewust@umich.edu>
Reported-by: Nadia Heninger <nadiah@cs.ucsd.edu>
Reported-by: Zakir Durumeric <zakir@umich.edu>
Reported-by: J. Alex Halderman <jhalderm@umich.edu>.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
Update for change in i2c-ocores.h which uses reg_shift to
specify the register offset shifts instead of regstep.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Acked-by: Richard Rojfors <richard.rojfors@pelagicore.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This commit adds device tree support for tps65217 pmic. And usage
details are added to device tree documentation. Driver is tested
by using kernel module with regulator set and get APIs.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The registers have stride 2 so we can write the loop properly now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes below build warning if CONFIG_OF is not set.
CC drivers/mfd/max77686.o
drivers/mfd/max77686.c:37:42: warning: 'max77686_pmic_dt_match' defined but not used [-Wunused-variable]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds device tree support for mfd driver and adds
Documentation/devicetree/bindings/mfd/max77686.txt.
This patch also intialize max77686 pointer to NULL in max77686_i2c_probe
to silent a compile time warning.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Presently driver expects irq_gpio pin in platform data and maps it to irq
itself. But we can also directly specify the interrupt in DT or platform file.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to TRM, though we mask the interrupts in interrupt-mask register,
interrupt source-register still provide the status of the masked interrupts.
So we should apply irq_mask_cur to read interrupt source-register value before
handling.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PMIC's regmap should be used to read pmic interrupt registers.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
device_init_wakeup uses the dev_name() of the device to set the
name of the wakeup_source which appears in
/sys/kernel/debug/wakeup_sources.
For a platform device, that name is not set until platform_device_add
calls dev_set_name.
So the call to device_init_wakeup() must be after the call to
platform_device_add().
Making this change causes correct names to appear in the
wakeup_sources file.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
in hw design, 800 is mainly for pmic control, while 805 for audio.
but there are 3 registers which controls class D speaker property,
and they are defined in 800 i2c client domain. so 805 codec driver
needs to use 800 i2c client to access class D speaker reg for
audio path management. so add this workaround for the purpose to
let 805 access 800 i2c in some scenario.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM800 and 88PM805 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according
to requirement.
88pm80x.c provides common i2c driver handling for both 800 and
805, such as i2c_driver init, regmap init, read/write api etc.
88pm800.c handles specifically for 800, such as chip init, irq
init/handle, mfd device register, including rtc, onkey, regulator(
to be add later) etc. besides that, 800 has three i2c device, one
regular i2c client, two other i2c dummy for gpadc and power purpose.
88pm805.c handles specifically for 805, such as chip init, irq
init/handle, mfd device register, including codec, headset/mic detect
etc.
the i2c operation of both 800 and 805 are via regmap, and 88pm80x-i2c
exported a group of r/w bulk r/w and bits set API for facility.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The core and irq Arizona parts should be boolean as they depend on non
exported symbols.
This fixes the following build errors:
ERROR: "wm5102_aod" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_irq" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "irq_set_chip_and_handler_name" [drivers/mfd/arizona-irq.ko] undefined!
ERROR: "wm5102_patch" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_init" [drivers/mfd/arizona-core.ko] undefined!
ERROR: "arizona_irq_exit" [drivers/mfd/arizona-core.ko] undefined!
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ARRAY_SIZE() may be larger than the number of supplies actually used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
References to the WM5102 tables need to be guarded.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We're testing for a specific value and while SPI does not detect I/O
errors I2C can.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensures we don't leak the enable we just did.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This ensures that if we are using a GPIO as a wake source it continues to
function while we're suspended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now we have regcache sync region we can use it to do a more efficient
sync of the pin configuration after we reset the device during suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than open coding the enable GPIO control in the MFD core use the
API to push the management on to the regulator driver. The immediate
advantage is slight for most systems but this will in future allow device
configurations where an external regulator is used for DCVDD.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
While the core isn't useful by itself it does depend on regmap so try to
force that on.
Reported-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8pCq
-----END PGP SIGNATURE-----
Merge tag 'mfd/wm5102' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into for-next
mfd: Initial support for Wolfson Arizona platform and WM5102 devices
The Wolfson Arizona platform is used to provide common register
interface to a series of low power audio hub CODECs, starting with the
WM5102. Since the features of these devices work over a range of
subsystems an MFD core driver is provided to instantiate the subdevices
and arbitrate access between them.
As the new regmap wake IRQ functionality is used as part of the driver
it is incorporated as a dependency.
During conversion to regmap_irq this hunk was missing being moved
to MFD driver to put the chip into clear on read mode. Also as slave
is now set use it to determine which slave for the register call.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a merge error the section of code passing the pdata for the
regulator driver to the mfd_add_devices via the children structure
was missing. This corrects this problem.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6040 needs CONFIG_IRQ_DOMAIN to compile, without this we have:
drivers/mfd/twl6040-irq.c: In function 'twl6040_irq_init':
drivers/mfd/twl6040-irq.c:164:2: error: implicit declaration of function 'irq_domain_add_legacy'
drivers/mfd/twl6040-irq.c:165:11: error: 'irq_domain_simple_ops' undeclared (first use in this function)
drivers/mfd/twl6040-irq.c:165:11: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 72fb92200d ("mfd/ab5500: delete
AB5500 support") deleted all files that used ab5500-core.h. That file
apparently was simply overlooked. Delete it too.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MC13xxx PMIC is mainly used on i.Mx SoC. On those SoC the SPI
hardware will deassert CS line as soon as the SPI FIFO is empty.
The MC13xxx hardware is very sensitive to CS line change as it
corrupts the transfer if CS is deasserted in the middle of a register
read or write.
It is not possible to use the CS line as a GPIO on some SoC, so we
need to workaround this by implementing a single SPI transfer to
access the PMIC.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fix the SPI regmap configuration, the wrong write flag was used.
Also, bits_per_word should not be set as the regmap spi implementation
uses a 8bits transfert granularity.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As the AB8500 is a subordinate MFD device to the DB8500-PRCMU,
for consistency and a better 1:1 depiction of how the hardware
is laid out, it is a good idea to register it in the same way
as we do for the other MFD child devices. In order for us to do
this successfully we have to pass AB8500's platform data when
registering the DB8500-PRCMU from platform code.
Also solves this issue:
WARNING: at fs/sysfs/dir.c:526 sysfs_add_one+0x88/0xb0()
sysfs: cannot create duplicate filename '/bus/platform/devices/ab8500-core.0'
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now this driver is using regmap API, the iolock mutex is not used and
can be removed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator device init data and resource for mfd subdev.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add flag to platform data to enable external 32-kHz crystal oscillator
(or square wave) input.
The tps6591x can use either an internal 32-kHz RC oscillator or an
external crystal (or square wave) to generate the 32-kHz clock.
The default setting depends on the selected boot mode. In boot mode 00
the internal RC oscillator is used at power-on, but the external crystal
oscillator (or square wave) can be enabled by clearing the ck32k_ctrl
flag in the device control register.
Note that there is no way to switch from the external crystal oscillator
to the internal RC oscillator.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During conversion to regmap_irq this hunk was missing being moved
to MFD driver to put the chip into clear on read mode. Also as slave
is now set use it to determine which slave for the register call.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Due to a merge error the section of code passing the pdata for the
regulator driver to the mfd_add_devices via the children structure
was missing. This corrects this problem.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add irq domain support for max8997 interrupts. The reverse mapping method
used is linear mapping since the sub-drivers of max8997 such as regulator
and charger drivers can use the max8997 irq_domain to get the linux irq
number for max8997 interrupts. All uses of irq_base in platform data and
max8997 driver private data are removed.
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Guard PM methods with CONFIG_PM_SLEEP and get rid of some unneeded #ifdefs.
This fixes below build warnings:
CC drivers/mfd/tc3589x.o
drivers/mfd/tc3589x.c:361:12: warning: 'tc3589x_suspend' defined but not used [-Wunused-function]
drivers/mfd/tc3589x.c:375:12: warning: 'tc3589x_resume' defined but not used [-Wunused-function]
SIMPLE_DEV_PM_OPS already defines constant dev_pm_ops, thus also fix
'duplicate const' sparse warning.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes below build warnings:
CC drivers/mfd/adp5520.o
drivers/mfd/adp5520.c:324:12: warning: 'adp5520_suspend' defined but not used [-Wunused-function]
drivers/mfd/adp5520.c:333:12: warning: 'adp5520_resume' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch fixes conflict between commit 8ae3559
"mfd: mc13xxx workaround SPI hardware bug on i.Mx"
and commit 10c7a5d "mfd: Use devm_* APIs for mc13xxx".
commit 8ae3559 changes regmap_init_spi to regmap_init.
So now we need to use devm_regmap_init rather than devm_regmap_init_spi.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (1fcb57d0) fixes
an issue where the ULPI PHYs were not held in reset while initializing
the EHCI controller. However, it also changes behavior in
omap-usb-host.c omap_usbhs_init by releasing reset while the
configuration in that function was done.
This change caused a regression on BB-xM where USB would not function
if 'usb start' had been run from u-boot before booting. A change was
made to release reset a little bit earlier which fixed the issue on
BB-xM and did not cause any regressions on 3430 sdp, the board for
which the fix was originally made.
This new fix, 'USB: EHCI: OMAP: Finish ehci omap phy reset cycle
before adding hcd.', (3aa2ae74) caused a regression on OMAP5.
The original fix to hold the EHCI controller in reset during
initialization was correct, however it appears that changing
omap_usbhs_init to not hold the PHYs in reset during it's
configuration was incorrect. This patch first reverts both fixes, and
then changes ehci_hcd_omap_probe in ehci-omap.c to hold the PHYs in
reset as the original patch had done. It also is sure to incorporate
the _cansleep change that has been made in the meantime.
I've tested this on Beagleboard xM, I'd really like to get an ack from
the 3430 sdp and OMAP5 guys before getting this merged.
v3 - Brown paper bag its too early in the morning actually run
git commit amend fix
v2 - Put cansleep gpiolib call outside of spinlock
Acked-by: Mantesh Sarashetti <mantesh@ti.com>
Tested-by: Mantesh Sarashetti <mantesh@ti.com>
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Tested-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allocate memory and irq for device state using devm_*
helpers to simplify memory accounting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that we leave the device with the pins in the expected
configuration if we leave it in reset over suspend, avoiding any
interoperation problems with other devices in the system.
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl6040 needs CONFIG_IRQ_DOMAIN to compile, without this we have:
drivers/mfd/twl6040-irq.c: In function 'twl6040_irq_init':
drivers/mfd/twl6040-irq.c:164:2: error: implicit declaration of function 'irq_domain_add_legacy'
drivers/mfd/twl6040-irq.c:165:11: error: 'irq_domain_simple_ops' undeclared (first use in this function)
drivers/mfd/twl6040-irq.c:165:11: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We need to call max77693_irq_exit() in max77693_i2c_probe error patch and
max77693_i2c_remove.
Current code already uses devm_kzalloc() to allocate memory for max77693.
Thus we should not call kfree(max77693), otherwise we got double free.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Commit 72fb92200d ("mfd/ab5500: delete
AB5500 support") deleted all files that used ab5500-core.h. That file
apparently was simply overlooked. Delete it too.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
They're not referenced outside this file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fixes the following sparse warnings:
drivers/mfd/max8997.c:209:4: warning: symbol 'max8997_dumpaddr_pmic' was not declared. Should it be static?
drivers/mfd/max8997.c:334:4: warning: symbol 'max8997_dumpaddr_muic' was not declared. Should it be static?
drivers/mfd/max8997.c:344:4: warning: symbol 'max8997_dumpaddr_haptic' was not declared. Should it be static?
drivers/mfd/max8997.c:426:25: warning: symbol 'max8997_pm' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Instead of just printing the register value, also output some
description of the value.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Force the Modem wakeup by asserting the CaWakeReq signal before the
hostaccess_req/ack ping-pong sequence. The Awake_req signal is de-asserted
asserted at the same time than the hostaccess_req. Return error on failure
case so that the client using this can take appropiate steps.
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since none of the users now reference the cache directly we can happily
remove the custom cache code and rely on the regmap cache.
For simplicity we don't bother with the register defaults tables but
instead read the defaults from the device - regmap is capable of doing
this, unlike our old cache infrastructure. This saves a lot of code and
allows us to cache the device revision information too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can just use regmap_update_bits() to achieve the same effect - it will
do the read/modify/update cycle for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the most simple possible transformation on the existing code so keep
the table sitting around, further patches in this series will delete the
existing cache code - the main purpose of this patch is to ensure that
we always have a cache for bisection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Hierarchically, the AB8500 is a child of the DB8500 PRCMU. So now that
Device Tree is being used and MFD core code is Device Tree aware, we
can simply register DB8500 PRCMU from Device Tree in the normal way
then allow the DB8500 PRCMU driver to register the AB8500 as a simple
MFD device at probe time.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AB8500 is soon to have its own IRQ domain. For this to be useful
the driver needs to be initialised earlier in the boot sequence. Here
we move initialisation forward from arch_initcall to core_initcall time.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the AB8500 has its own IRQ domain it needs to be initialised earlier
in the boot sequence. As the AB8500 relies on the DB8500 PRCMU we need to
reflect this change for the PRCMU driver too.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During Device Tree enablement of the ab8500 and db8500-prcmu drivers,
a decision was made to omit registration through the MFD API and use
Device Tree directly. However, because MFD devices have a different
address space and the ab8500 and db8500 both use I2C to communicate,
this causes issues with address translation during execution of
of_platform_populate(). So the solution is to make the MFD core aware
of Device Tree and have it assign the correct node pointers instead.
To make this work the MFD core also needs to be awere of IRQ domains,
as Device Tree insists on IRQ domain compatibility. So, instead of
providing an irq-base via platform code, in the DT case we simply
look up the IRQ domain and map to the correct virtual IRQ.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is only one method used to communicate with the DB8500 PRCMU, via I2C.
Now this can be assumed, there is no requirement to specify the protocol in
the function name. This patch removes protocol specifics and uses a more
generic naming convention.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As the AB8500 is an IRQ controller in its own right, here we provide
the AB8500 driver with IRQ domain support. This is required if we wish
to reference any of its IRQs from a platform's Device Tree.
Cc: Naga Radheshy <naga.radheshy@stericsson.com>
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Cc: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the correct compatible string for use during Device Tree
population. Without it the DB8500 PRCMU will not be probed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
During ab8500-core clean-up the Kconfig entry for AB8500_I2C_CORE
was left remnant. This patch simply removes it.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The kernel now forces IRQs to be ONESHOT if no IRQ handler is passed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The MC13xxx PMIC is mainly used on i.Mx SoC. On those SoC the SPI
hardware will deassert CS line as soon as the SPI FIFO is empty.
The MC13xxx hardware is very sensitive to CS line change as it
corrupts the transfer if CS is deasserted in the middle of a register
read or write.
It is not possible to use the CS line as a GPIO on some SoC, so we
need to workaround this by implementing a single SPI transfer to
access the PMIC.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fix the SPI regmap configuration, the wrong write flag was used.
Also, bits_per_word should not be set as the regmap spi implementation
uses a 8bits transfert granularity.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now this driver is using regmap APIs, the iolock mutex is not used and can be
removed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is to address the following warning during compilation time:
drivers/mfd/da9052-core.c: In function ‘da9052_device_init’:
drivers/mfd/da9052-core.c:646: warning: unused variable ‘desc’
This variable is indeed no longer in use (change can be traced back
to commit: 8614419451).
Signed-off-by: Krzysztof Wilczynski <krzysztof.wilczynski@linux.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch is device driver for MAX77686 chip.
MAX77686 is PMIC and includes regulator and rtc on it.
This driver is core of MAX77686 chip, so provides common support for
accessing on-chip devices. It uses irq_domain to manage irq and regmap
to read/write data to its register with i2c bus.
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds the build system hookup for the core driver and the WM5102.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The first Arizona class device is the WM5102. This patch adds the data
tables for this, mainly consisting of regmap data. This patch depends
on the recently added support for wake IRQs in the regmap subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds SPI bus interface code for the devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds I2C bus interface code for the devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds support for the interrupt controller on Arizona class devices.
Since there are two interrupt domains in the device which share a single
/IRQ pin by default we use two regmap IRQ domains with a trivial demux
interrupt domain used to distribute the interrupts to the two devices.
The devices do support multiple interrupt signals, future work will enable
support for using this feature to avoid the demux.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several forthcoming Wolfson devices are based on a common platform
known as Arizona allowing a great deal of reuse of driver code. This
patch adds core support for these devices.
In order to handle systems which do not use the generic clock API a
simple wrapper for the 32kHz clock domain in the devices is provided.
Once the generic clock API is widely available this code will be moved
over to use that.
For simplicity some WM5102 specific code is included in the core driver,
the effort involved in splitting the device out isn't worth it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The charger needs usb3v1 to be running, so add a new consumer to
keep it running.
This allows the charger to draw current even when the USB driver has
powered down.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This patch adds a fixed regulator for use by the SMSC911x Ethernet
chip driver into the db8500 Device Tree. It also references other
regulators required by the same device.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
Patil, Rachna