Before adding new modes, rename the only existing one to report
the bit depth to distinguish it from future additions.
While at it, briefly describe the mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support the get_selection() pad operation to report the device
full pixel array size, the currently applied analogue crop rectangle and
the active pixel array dimensions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Break format handling out from the main driver structure.
This commit prepares for the introduction of more sensor formats and
resolutions by instrumenting the existing operation to work on multiple
modes instead of assuming a single supported one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver structure name is referred to with different names ('ov5647',
'state', 'sensor') in different functions in the driver.
Polish this up by using 'struct ov5647 *sensor' everywhere.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add controls to support AWB, AEC and AGC. Also add control support to
set exposure (in lines) and analogue gain (as a register code).
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the driver mutex to protect s_stream() operations.
This will become more relevant once the sensor will support more formats
and set_format() could be issue concurrently to s_stream().
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the .enum_frame_size subdev pad operation.
As the driver only supports one format and one resolution at the moment
the implementation is trivial.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename __sensor_init() function to ov5647_set_mode() as the function
is a regular one and the double underscores prefix shall be removed, and
then move it to program the mode at s_stream(1) time, not at sensor power
up.
Break out from __sensor_init() the stream_off() operation call at sensor
power up to coax the lanes in LP-11 state.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov5647_read()/ov5647_write() return in case of success the number
of bytes read or written respectively. This requires callers to check
if the return value is less than zero to detect an error. Unfortunately,
in several places, callers directly return the result of a read/write
call, causing issues when the returned valued is checked to be different
from zero to detect an error.
Fix this by returning zero if i2c_master_send() and i2c_master_read()
return a positive value (the number of bytes written or read).
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the boilerplate license text with the SPDX identifier.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver has some obvious style issues which are worth fixing before
expanding the driver capabilities.
Fix:
- Variable declaration order
- Function parameters alignment
- Multi-line comments and spurious line breaks
- Use lowercase for hexadecimal values
- > 80 cols lines
Cosmetic change, no functional changes intended.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver currently support a single format. Fix its initialization to
use the only supported resolution.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no way to query the subdevice for the supported
resolutions. Add set_fmt and get_fmt implementations. Since there's
only one format supported set_fmt does nothing and get returns single
format.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for optional non-continuous clock mode to the ov5647
sensor driver.
Non-continuous clock saves a small amount of power and on some SoCs
is easier to interface with.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for an optional GPIO connected to PWDN on the sensor. This
allows the use of hardware standby mode where internal device clock
and circuit activities are halted.
Please note that power is off when PWDN is high.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix obtaining CCS static data version minor part correctly. Instead, the
upper 8 bits were obtained from the major version number.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The highest fundamental frequency signal for C-PHY is half of the symbol
rate which is similar to D-PHY. Take this into account in ccs-pll.
Also remove the outdated comment.
Fixes: 8030aa4f9c ("media: ccs-pll: Add C-PHY support")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Try parsing the firmware also as C-PHY. Do this only after D-PHY as older
firmware may not explicitly specify bus-type in which case D-PHY is the
default.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print pixel rates on CSI-2 bus as well as in pixel array as the variation
allowed in PLL capabilities makes this non-trivial to figure out
otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Support dual data rate operational system and pixel clocks by conveying
the flags to the PLL calculator and updating how the link rate is
calculated.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for dual data rate operational system and pixel clocks. This
is implemented using two PLL flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for sensors that either require dual PLL or support single or
dual PLL but use dual PLL as default.
Use sensor default configuration for sensors that support both modes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for sensors that have separate VT and OP domain PLLs.
This support is trivial in the sense that it aims for the same VT pixel
rate than that on the CSI-2 bus. The vast majority of sensors is better
supported by higher frequencies in VT domain in binned and possibly scaled
configurations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Separate VT divisor limit calculation from the rest of the VT PLL branch
calculation. This way it can be used for dual PLL support as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PLL calculator only searched even total divisor values apart from one,
but this is wrong: the total divisor is odd in cases where system divisor
is one. Fix this by including odd total PLL values where system divisor is
one to the search.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make VT divisors 16-bit unsigned numbers. They don't need 32 bits after
all.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Refactor bounds checks so that the caller can decide what to check. This
allows doing the checks early, when the values are available.
This also adds front OP PLL configuration and limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print information on PLL tree configuration based on the flags. This also
adds support for printing dual PLL trees, and better separates between OP
and VT PLL trees.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Better separate OP PLL branch calculation from VT branch calculation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some sensors support derating (VT domain speed faster than OP) or
overrating (VT domain speed slower than OP). While this was supported for
the driver, the hardware support for the feature was never verified. Do
that now, and for those devices without that support, VT and OP speeds
have to match.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split off the VT sub clock tree calculation from the rest, into its own
function. Also call the op_pll_fr argument pll_fr, since soon these may
not be OP tree values.
This paves way for additional features in the future such as dual PLL
support.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add C-PHY support for the CCS PLL calculator.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add sanity checks for fields that could cause division by zero.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Flexible OP PLL pixel clock divider allows a higher OP pixel clock than
what the bus can transfer. This generally makes it easier to select pixel
clock dividers.
This changes how the pixel rate on the bus and minimum VT divisor are
calculated, as the pixel rate is no longer directly determined by the
OP pixel clock and the number of the lanes.
Also add a sanity check for sensors that do not support flexible OP PLL
pixel clock divider. This could have caused the PLL calculator to come up
with an invalid configuration for those devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The l parameter defines the number of clock cycles to process a single
pixel per OP lane. It is calculated based on a new register
op_bits_per_lane.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS allows odd PLL dividers other than 1, granted that the corresponding
capability bit is set. Support this both in the PLL calculator and the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for decoupled OP domain clock calculation. This means that the
number of VT and OP domain clocks are no longer dependent on the number of
CSI-2 lanes in the lane speed mode.
The support also replaces the existing quirk flag to calculate OP domain
clocks per lane.
Also support decoupled OP domain calculation in the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Convey the relevant PLL flags to the PLL calculator. Also the lane speed
model affects how the link rate is calculated on the CSI-2 bus, as the
rate is total of all lanes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
CCS PLL includes a capability to calculate the VT clocks on per-lane
basis. Add support for this feature.
Move calculation of the pixel rate on the CSI-2 bus early in the function
as everything needed to calculate it is already available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use uint32_t instead of unsigned int for a variable that contains
explicitly 32-bit numbers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The additional multiplier (for higher VT timing) of the PLL multiplier was
checked against the upper limit but the result was rounded up, possibly
producing too high additional multiplier. Round down instead to keep
within hardware limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The comment is about minimum PLL multiplier but the related check really
deals with the maximum PLL multiplier.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The external clock frequency times the PLL multiplier may exceed the value
range of 32-bit unsigned integers. Instead perform the same calculation y
using two divisions.
The result has some potential to be different, but that's ok: this number
is used to limit the range of pre-PLL divisors to find optimal values. So
the effect of the rare case of a different result here would mean an
invalid pre-PLL divisor is tried. That will be found out a little later in
any case.
Also guard against dividing by zero if the external clock frequency is
higher than the maximum OP PLL output clock --- a rather improbable case.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The lower bound of the pre-PLL divider was calculated based on OP SYS
clock frequency which is also affected by the OP SYS clock divider. This
is wrong. The right clock frequency is that of the PLL output clock.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OP system clock frequency defines the CSI-2 bus clock frequency, not
the PLL output clock frequency. Both values were overwritten in the end,
but the wrong limit value was used for the OP system clock frequency,
possibly leading to too high frequencies being used.
Also remove now duplicated calculation of OP system clock frequency later
in the PLL calculator.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the BIT macro for setting individual bits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS pll is used by the CCS driver at the moment, but documenting the
interface makes sense. It's non-trivial and the calculator could be used
elsewhere.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This way the struct will use less memory, with better packing and no waste
due to unsigned long.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Differentiate between CSI-2 D-PHY and C-PHY. This does not yet include
support for C-PHY.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The parallel bus PLL calculation has no users. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The VT divisor search can be ended if we've already found the value that
corresponds exactly the total divisor, as there are no better (lower)
values available.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the correct video timing divisor to calculate the SYS divisor. Instead
of the current value, the minimum was used. This could have resulted in a
too low SYS divisor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS spec supports a lot of variation in the PLL. Split the PLL in
front and back parts to better prepare for supporting it.
Also use CCS compliant naming for IP and OP PLL frequencies (i.e. include
"clk" in the name).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pll->pll_op_clk_freq is a 32-bit number. It does not need div_u64 to
divide it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
rval wasn't set, resulting in probe returning zero instead of an error.
Fixes: de10c1619c ("[media] smiapp: Get clock rate if it's not available through DT")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no intialization for the 'reg' variable, so printing
it produces undefined behavior as well as a compile-time warning:
drivers/media/i2c/ccs/ccs-core.c:314:49: error: variable 'reg' is uninitialized when used here [-Werror,-Wuninitialized]
"0x%8.8x %s pixels: %d %s (pixelcode %u)\n", reg,
Remove the variable and stop printing it.
Fixes: fd9065812c ("media: smiapp: Obtain frame descriptor from CCS limits")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clang points out that the error handling in ov02a10_s_stream() is
broken, and just returns a random error code:
drivers/media/i2c/ov02a10.c:537:6: warning: variable 'ret' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/i2c/ov02a10.c:568:9: note: uninitialized use occurs here
return ret;
^~~
drivers/media/i2c/ov02a10.c:537:2: note: remove the 'if' if its condition is always false
if (ov02a10->streaming == on)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
If streaming is already on, leave it that way and return success.
Suggested-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Fixes: 91807efbe8 ("media: i2c: add OV02A10 image sensor driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use regulators vio and vcore besides vana. The regulators were always
there but on many boards they've been hard wired. Control them explicitly
now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
SMIA nor CCS need these delays; remove them.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Longer idle period is required on I²C bus before the first transaction
after lifting xshutdown.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Over the years (and renaming) some lines that may well be wrapped ended up
being over 80 characters, likewise there are shorter lines that can be
merged. Do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If pm_runtime_get_sync() fails, there's no need to set the device active
again. Also, in the same case to return the usage_count to zero,
pm_runtime_put_noidle() is enough.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Write manufacturer specific registers (MSRs) from file to the sensor on
sensor power-on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make the delay between I²C access retries a range between 1 and 2 ms. Also
make the number of retries 10 instead of 5, in order not to reduce the
total amount of time.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use my @linux.intel.com e-mail address in the CCS driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change MODULE_LICENSE to "GPL v2" as indicated by the SPDX tag.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
MIPI CCS replaces SMIA and SMIA++ as the current standard. CCS brings new
features while existing functionality will be supported. Rename the
smiapp-pll as ccs-pll accordingly.
Also add Intel copyright to the files.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some limit values are available in q16.q16 format, referred to as 32-bit
unsigned ireal in CCS. Read these correctly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of converting the limit values at register read time, do that at
access time instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The limit values will be raw soon, and the conversion takes place later
on. Prepare for that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rework quirk and 8-bit only access functions with a single function that
takes arguments. This is later extensible to support yet more flags.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If an internal driver error was encountered, BUG was issued. Instead, do
less harsh WARN_ON_ONCE and try to manage with the consequences.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The NULL check is not needed as the functions do not return NULL. Remove
the check (and BUG).
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The register arrays have a certain size but not all the entries will be
relevant. In practice reading can be stopped after encountering a zero
value in the array. Do that to avoid extra reads.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read the CCS static data for sensors and modules. The files are expected
to be found in "ccs" directory.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The module revision number major and minor are both 8 bits while the
sensor revision number is 16 bits. Combine the module revision into one
number.
This also adds printing the lowest 8 bits of the module version through
the sysfs attribute.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a parser library for parsing the CCS static data format.
The library may be also compiled in user space as the format has uses also
in the user space. Therefore it is dual licensed under the 3-clause BSD
license as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Let v4l2_fwnode_endpoint_alloc_parse to figure out the type of the data
bus. As the old bindings did not require the "bus-type" property, we need
to rely on guessing between CSI-2 D-PHY and CCP2. Setting the type to
CSI-2 D-PHY will parse just that and succeed even if no data-lanes are
set.
Also add a comment on the matter to the driver to avoid breaking this in
the future.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to allocate the hardware configuration struct separately.
Put it in struct ccs_sensor.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to support platform data; remove support for conveying hardware
configuration that way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The I²C ID table is no longer needed; remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS compliant sensors use device ID "MIPI0200". Use this id for ACPI
device matching.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add device data specific to DT compatible ID to tell SMIA and CCS devices
apart already in power-up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add "mipi-ccs-1.0" and "mipi-ccs-1.1" compatible strings to the CCS
driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If the device is powered off (for example during system suspend to ram)
the devices loses its configuration, especially the slave i2c mappings
and other configuration set at probe time. This renders the device
unusable and the only way to recover is to unbind and rebind the device
to the driver to run the probe setup again.
Add an early resume callback that reinitializes the device and setup the
slave i2c address mappings and other probe time configuration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's not enough to set the CSI-2 virtual channel for TXA and TXB during
probe: it also needs to be set when the device is reset. Move the virtual
channel selection to adv748x_reset() that is called during probe and
when the device needs to be reset.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's not enough to select the AFE input port during probe: it also needs
to be set when the device is reset. Move the port selection to
adv748x_reset() that is called during probe and when the device needs to
be reset.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
During probe the i2c slave addresses are set two times in a row, once in
adv748x_initialise_clients() and once directly after in adv748x_reset().
Remove the call to adv748x_set_slave_addresses() in
adv748x_initialise_clients() as it's only called during probe while
adv748x_reset() is called during probe and normal operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If of_graph_get_endpoint_by_regs() return NULL, it will return 0 rather
than an errno, because we doesn't initialize the return value.
Fixes: 0556f1d580 ("media: tvp5150: add input source selection of_graph support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To comply with the intended usage of the V4L2 selection target when
used to retrieve a sensor image properties, adjust the rectangles
returned by the imx219 driver.
The top/left crop coordinates of the TGT_CROP rectangle were set to
(0, 0) instead of (8, 8) which is the offset from the larger physical
pixel array rectangle. This was also a mismatch with the default values
crop rectangle value, so this is corrected. Found with v4l2-compliance.
While at it, add V4L2_SEL_TGT_CROP_BOUNDS support: CROP_DEFAULT and
CROP_BOUNDS have the same size as the non-active pixels are not readable
using the selection API. Found with v4l2-compliance.
[reword commit message, use macros for pixel offsets]
Fixes: e6d4ef7d58 ("media: i2c: imx219: Implement get_selection")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9271 GPIO1 line that controls the sensor reset is by default
enabled after a serializer chip reset.
As rdacm20 does not go through an explicit serializer reset, make sure
GPIO1 is enabled to make the camera module driver more robust.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix GPIO enable/disable operations which wrongly read the 0x0f register
to obtain the current mask of the enabled lines instead of using
the correct 0x0e register.
Also fix access to bit 0 of the register which is marked as reserved.
Fixes: 34009bffc1 ("media: i2c: Add RDACM20 driver")
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently pointer nvm is being dereferenced before it is being null
checked. Fix this by moving the assignments of pointers client and
ov2740 so that are after the null check hence avoiding any potential
null pointer dereferences on pointer nvm.
Fixes: 5e6fd339b6 ("media: ov2740: allow OTP data access during streaming")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The lock in ov9734 is used to protect the streaming state and
serialize the stream on and off callbacks, it should be hold before
checking the streaming state in ov9734_set_stream().
Reported-by: Tomasz Figa <tfiga@chromium.org>
Reported-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The DT bindings documented "reset-gpios" property but the driver never
made use of it. Instead it used a GPIO called "xshutdown", with apprently
wrong polarity.
Fix this by requesting "reset" GPIO with the right polarity first, and if
that fails, then request "xshutdown" GPIO with the old polarity. This way
it works for new users as expected while if someone, somewhere, depended
on "xshutdown" GPIO, that continues to work as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This removes a warning at driver probe time telling that one or two
entities have no function set. The function used for both the binner and
scaler is the scaler.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver doesn't do anything tangible with profiles. Remove the notion,
and use the capabilities directly.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the "smiapp" driver as "ccs". MIPI CCS is the contemporary standard
for raw Bayer camera sensors. The driver retains support for the SMIA++
and SMIA compliant camera sensors. A module alias is added for old user
space using "smiapp" module name.
Add Intel copyright while at it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call CCS compliant sensors as "ccs" instead of "smiapp" in absence of a
device specific name. This is done based on the value of the manufacturer
ID register that is only present in CCS.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename internal names to reflect the driver's new reference. The module
name remains the same.
Also fix trivial coding style issues on the way related to e.g. alignment
changes due to the rename.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename register access functions by changing smiapp to ccs.
The functions operating on register addresses have "addr" appended to the
name.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This function is no longer needed as the smiapp_write() function can be
used to write 8-bit registers with plain register addresses.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Switch to CCS standard registers where they exist. The still relevant SMIA
registers are left as-is and the redundant ones are removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use CCS limits for obtaining binning capabilities and subtypes.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CCS limits have the information so use it instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Obtain the frame descriptor from the CCS limits, instead of reading them
directly from the frame descriptor registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the CCS limit definitions instead of the SMIA ones. This allows
accessing CCS capabilities where needed as well as dropping the old SMIA
limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read limit and capability values into a driver allocated buffer. This will
later replace (most of) the existing SMIA limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read MIPI CCS manufacturer and version information, and use the CCS IDs
over SMIA whenever they are set.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add two helper macros for reading and writing the CCS registers as defined
in ccs-regs.h.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove macros for defining new SMIA registers, instead put the register
flags to the register definition itself. Also move the register flags to
the same file.
This is not expected to be updated but rather left there as a reference.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calculate the limit offsets and the size of the limit buffer. CCS limits
are read into this buffer, and the offsets are helpful in accessing the
information in it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the CCS register flags instead of the old smia flags. The
new flags include the register width information that was separate from
the register flags previously.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Import CCS register and limit definitions. These files are generated by a
Perl script based on a text-based register definition file. The generator
was added on
commit 1ec0b899c2 ("media: ccs: Add the generator for CCS register definitions and limits")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These writes to 0x162, 0x163 already appear earlier in the struct for
the 1920x1080 mode and do not need to be repeated.
Signed-off-by: Sameer Puri <purisame@spuri.io>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is supposed to return negative error codes but the type is bool so
it returns true instead.
Fixes: b47b79d8a2 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Stop video streaming when requested.
When s_stream is called to stop the video streaming, if/else condition calls
start_streaming function instead of the one for stopping it.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Signed-off-by: Daniel Gomez <daniel@qtec.com>
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The flag V4L2_SUBDEV_FL_HAS_EVENTS is required if the subdev can
generate events. It can create events from the ctrl handler, therefore
this is required.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Because clk_disable_unprepare() already checked NULL clock parameter,
so the additional check is unnecessary, just remove it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OTP data access of ov2740 need enable the streaming mode to load
and it could be done in any time, so driver need allow the OTP
data access during streaming instead of return EBUSY, this patch
try to read the OTP data out in STREAMON if OTP data is not ready
before first time streaming start.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OTP data access of ov2740 in probe need power up, it may cause
the camera flash LED blink during probe if the LED use same power
rail with camera, this patch move the OTP data access out of
probe, it will only occur on demand from user by nvmem sysfs.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a v4l2 sub-device driver for the OminiVision ov9734 image sensor
which can deliver maximum 720p image frames at 30 fps. This driver
also add vertical blanking, exposure, test pattern, digital and analog
gain control for the image sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove Jason Chen's e-mail address for it no longer works.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adding muliple status together loses individual failures.
Check each status separately.
Clean up some other returns for consistency.
Fixed several coding style problems by running
the file through checkpatch.pl --fix-inplace
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for test pattern control supported by the sensor.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to read the bus-type for V4L2_MBUS_BT656 and enable BT.656
mode in the sensor if needed.
For backward compatibility with older DTS where the bus-type property was
not mandatory, assume V4L2_MBUS_PARALLEL as it was the only supported bus
at the time. v4l2_fwnode_endpoint_alloc_parse() will not fail if
'bus-type' is not specified.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Parse endpoint properties using v4l2_fwnode_endpoint_alloc_parse()
to determine the bus type and store it in the driver structure.
Set bus_type to V4L2_MBUS_PARALLEL as it's the only supported one
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_fwnode_parse_endpoint() function can make use of defaults in
multiple bus types. To use this feature, all callers must zero the rest of
the fields of this struct, too. All other drivers appear to do that
already apart from this one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the mode 6 for the sensor, this mode uses
3/8 subsampling and 3 horizontal binning.
Aspect ratio is changed.
Split the bin_ratio variable into two parts, one for
width and one for height, as the ratio is no longer preserved
when doing subsampling in this mode.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX274 has analog 2.8V supply, digital core 1.8V supply, and vddl digital
io 1.2V supply which are optional based on camera module design.
IMX274 also need external 24Mhz clock and is optional based on
camera module design.
This patch adds support for IMX274 power on and off to enable and
disable these supplies and external clock.
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sensor should already be in standby during remove and there is no
need to configure sensor registers for stream stop.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As per Sony IMX274 Y_OUT_SIZE should be the height of effective
image output from the sensor which are the actual total lines
sent over MIPI CSI to receiver.
So, Y_OUT_SIZE should be same as crop height and this patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The minimal valid exposure value should be 4 lines instead of 8 for
ov2740 mannual exposure control.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If driver is built without ACPI, the struct acpi_device_id won't be
used:
drivers/media/i2c/imx355.c:1836:36: warning:
'imx355_acpi_ids' defined but not used [-Wunused-const-variable=]
[Sakari Ailus: Added a space before __maybe_unused]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If driver is built without ACPI, the struct acpi_device_id won't be
used:
drivers/media/i2c/imx319.c:2536:36: warning:
'imx319_acpi_ids' defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences. White at it, use 'dev' directly instead of 'imx290->dev'.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pointer to 'struct v4l2_subdev' is stored in drvdata via
v4l2_i2c_subdev_init() so there is no point of a dance like:
struct i2c_client *client = to_i2c_client(struct device *dev)
struct v4l2_subdev *sd = i2c_get_clientdata(client);
This allows to remove local variable 'client' and few pointer
dereferences.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
tvp7002.c: In function 'tvp7002_g_register':
tvp7002.c:691:11: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
691 | reg->val = val;
| ~~~~~~~~~^~~~~
Just return without setting 'reg' if tvp7002_read returns an error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
struct s5k5baf_fw ends with this:
struct {
u16 id;
u16 offset;
} seq[0];
u16 data[];
};
which is rather confusing and can cause gcc warnings:
s5k5baf.c: In function 's5k5baf_load_setfile.isra':
s5k5baf.c:390:13: warning: array subscript 65535 is outside the bounds of an interior zero-length array 'struct <anonymous>[0]' [-Wzero-length-bounds]
390 | if (f->seq[i].offset + d <= end)
| ~~~~~~^~~
It turns out that 'data[]' is used in only one place and it can
easily be replaced by &fw->seq[0].id and 'seq[0]' can be replaced by
'seq[]'.
This is both more readable and solved that warnings.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
tc358743_cec_isr is misnammed, it is not the main isr.
So rename it to be consistent with its siblings,
tc358743_cec_handler.
It also does not check if its input parameter 'handled' is
is non NULL like its siblings, so add a check.
Fixes: a0ec8d1dc4 ("media: tc358743: add CEC support")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis flags this error
tc358743.c:1468:9: warning: Branch condition evaluates
to a garbage value
return handled ? IRQ_HANDLED : IRQ_NONE;
^~~~~~~
handled should be initialized to false.
Fixes: d747b806ab ("[media] tc358743: add direct interrupt handling")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OV8856 supports 3264x2448 @ 30 FPS, which is added
in this commit.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OV8856 supports 1632x1224 @ 60 FPS, which is added
in this commit.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_async_notifier_add_subdev() requires the asd to be allocated
dynamically, but the max9286 driver embeds it in the max9286_source
structure. This causes memory corruption when the notifier is destroyed
at remove time with v4l2_async_notifier_cleanup().
Fix this issue by registering the asd with
v4l2_async_notifier_add_fwnode_subdev(), which allocates it dynamically
internally. A new max9286_asd structure is introduced, to store a
pointer to the corresonding max9286_source that needs to be accessed
from bound and unbind callbacks. There's no need to take an extra
explicit reference to the fwnode anymore as
v4l2_async_notifier_add_fwnode_subdev() does so internally.
While at it, use %u instead of %d to print the unsigned index in the
error message from the v4l2_async_notifier_add_fwnode_subdev() error
path.
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
During testing this sensor on iW-RainboW-G21D-Qseven platform in 8-bit DVP
mode with rcar-vin bridge noticed the capture worked fine for the first run
(with yavta), but for subsequent runs the bridge driver waited for the
frame to be captured. Debugging further noticed the data lines were
enabled/disabled in stream on/off callback and dumping the register
contents 0x3017/0x3018 in ov5640_set_stream_dvp() reported the correct
values, but yet frame capturing failed.
To get around this issue data lines are enabled in s_power callback.
(Also the sensor remains in power down mode if not streaming so power
consumption shouldn't be affected)
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for adding DVP configuration in s_power callback
move mipi configuration into separate function
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Keep the sensor in software power down mode and wake up only in
ov5640_set_stream_dvp() callback.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Alan Chiang's e-mail address no longer works. Remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9VerweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGhc4H/iHD6qLdB36gZB6K
oc2nJyrqyWitv4ti2Mnt5PA7o4wX4l6nnr1QvoaJ4BRs5Ja1czRvb2XDmdzqAoIA
xITGoafqaAeDfxQ91bWrJsVN0pCRKiGwddXlU7TWmqw/riAkfOqi6GYKvav4biJH
+n1mUPQb1M2IbRFsqkAS+ebKHq3CWaRvzKOEneS88nGlL5u31S9NAru8Ru/fkxRn
6CwGcs1XRaBPYaZAhdfIb0NuatUlpkhPC9yhNS9up6SqrWmK3m65vmFVng6H0eCF
fwn1jVztboY/XcNAi5sM9ExpQCql6WLQEEktVikqRDojC8fVtSx6W55tPt7qeaoO
Z6t4/DA=
=bcA4
-----END PGP SIGNATURE-----
Merge tag 'v5.9-rc4' into patchwork
Linux 5.9-rc4
* tag 'v5.9-rc4': (1001 commits)
Linux 5.9-rc4
io_uring: fix linked deferred ->files cancellation
io_uring: fix cancel of deferred reqs with ->files
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
...
rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The unit of exposure value is different from other OmniVision sensors,
driver will divide by 2 before set register, the exposure range exposed
by v4l2 ctrl to user should be same as others, so the calculation for
the maximum exposure value in current driver need be fixed.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make use of SCCB APIs for regmap operations.
Remove i2c_check_functionality as devm_regmap_init_sccb
does it for us.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
1) the numerator and/or denominator might be 0, in that case
fall back to the default frame interval. This is per the spec
and this caused a v4l2-compliance failure.
2) the updated frame interval wasn't returned in the s_frame_interval
subdev op.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
clang static analysis reports this error
m5mols_core.c:767:4: warning: Called function pointer
is null (null dereference) [core.CallAndMessage]
info->set_power(&client->dev, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In other places, the set_power ptr is checked.
So add a check.
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the error return from the call to max9286_read is masked
with 0xf0 so the following check for a negative error return is
never true. Fix this by checking for an error first, then masking
the return value for subsequent conflink_mask checking.
Addresses-Coverity: ("Logically dead code")
Fixes: 66d8c9d242 ("media: i2c: Add MAX9286 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Although the code is correct and doing the right thing, the clock diagram
showed the wrong register for the bit divider, which had me doubting the
understanding of the tree. Fix this to avoid doubts in the future.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OTP data was not ready after registered as nvmem device, it is
risky as the nvmem read may happen once the device exists, this patch
get the OTP data ready before registering the nvmem device. OTP data
missing should not break the normal camera sensor probe, so use a
warning instead of an error message.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Suggested-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccinelle reports:
drivers/media/i2c/tda1997x.c:911:6-21:
WARNING: Assignment of 0/1 to bool variable
drivers/media/i2c/tda1997x.c:939:2-17:
WARNING: Assignment of 0/1 to bool variable
drivers/media/i2c/tda1997x.c:947:4-19:
WARNING: Assignment of 0/1 to bool variable
Replace assignment to 1 with true and assignment to 0 with false.
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccinelle report:
drivers/media/i2c/imx219.c:1191:1-18:
WARNING: Assignment of 0/1 to bool variable
Replace the assignment to 0 with false instead.
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver expects struct gpio_chip has of_node field and that field is
only there if CONFIG_OF_GPIO is defined. Fix this by changing the OF
dependency to OF_GPIO.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After the recent conversion of the media build infrastructure to select
V4L2 components instead of depending on their presence, which took place
in:
32a363d0b0 ("media: Kconfig files: use select for V4L2 subdevs and MC")
imx214 stands out as being the (only?) media I2C driver that still depends
on a V4L2 core symbol instead of selecting it.
This confuses the build system which claims it has detected a circular
dependency when other drivers select the same symbol as the imx214
driver does.
drivers/media/i2c/Kconfig:728:error: recursive dependency detected!
drivers/media/i2c/Kconfig:728: symbol VIDEO_IMX214 depends on V4L2_FWNODE
drivers/media/v4l2-core/Kconfig:71: symbol V4L2_FWNODE is selected by VIDEO_BCM2835_UNICAM
drivers/media/platform/bcm2835/Kconfig:3: symbol VIDEO_BCM2835_UNICAM depends on VIDEO_V4L2_SUBDEV_API
drivers/media/v4l2-core/Kconfig:19: symbol VIDEO_V4L2_SUBDEV_API depends on MEDIA_CONTROLLER
drivers/media/Kconfig:168: symbol MEDIA_CONTROLLER is selected by VIDEO_IMX214
Fix this by making the imx214 driver select V4L2_FWNODE instead of
depending on it and align it with all the other drivers.
Fixes: 32a363d0b0 ("media: Kconfig files: use select for V4L2 subdevs and MC")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the newly introduced get_mbus_config operation to report the
number of currently used data lanes on the MIPI CSI-2 interface.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When outputting SD-Core output through the TXA MIPI CSI-2 interface,
the number of enabled data lanes should be reduced in order to guarantee
that the two video formats produced by the SD-Core (480i and 576i)
generate a MIPI CSI-2 link clock frequency compatible with the MIPI D-PHY
specifications.
Limit the number of enabled data lanes to 2, which is guaranteed to
support 480i and 576i formats.
Cache the number of enabled data lanes to be able to report it through
the new get_mbus_config operation.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the new get_mbus_config and set_mbus_config pad operations in place
of the video operations currently in use.
Compared to other drivers where the same conversion has been performed,
ov6650 proved to be a bit more tricky, as the existing g_mbus_config
implementation did not report the currently applied configuration but
the set of all possible configuration options.
Adapt the driver to support the semantic of the two newly introduced
operations:
- get_mbus_config reports the current media bus configuration
- set_mbus_config applies only changes explicitly requested and updates
the provided cfg parameter to report what has actually been applied to
the hardware.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the existing users of the g_mbus_config video operation to use the
newly introduced get_mbus_config pad operations.
All the ported drivers report a static media bus configuration and do no
support s_mbus_config so the operation implementation has not changed.
Bridge drivers needs to call the new pad operation and will receive an
-ENOICTLCMD when calling the old g_mbus_config video operation
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The RDACM20 is a GMSL camera supporting 1280x800 resolution images
developed by IMI based on an Omnivision 10635 sensor and a Maxim MAX9271
GMSL serializer.
The GMSL link carries power, control (I2C) and video data over a
single coax cable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9286 is a 4-channel GMSL deserializer with coax or STP input and
CSI-2 output. The device supports multicamera streaming applications,
and features the ability to synchronise the attached cameras.
CSI-2 output can be configured with 1 to 4 lanes, and a control channel
is supported over I2C, which implements an I2C mux to facilitate
communications with connected cameras across the reverse control
channel.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2 sub-device driver for DW9768 voice coil motor,
providing control to set the desired focus via IIC serial interface.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes checkpatch warnings of "msleep < 20ms can sleep for up to 20ms".
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver does not call media_entity_cleanup() in the error handler
of tvp5150_registered() and tvp5150_remove(), while it has called
media_entity_pads_init() at first.
Add the missed calls to fix it.
Fixes: 0556f1d580 ("media: tvp5150: add input source selection of_graph support")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove the confusing SoC Camera reference.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ov2740 includes 512bytes of one-time programmable memory and
256 bytes are reserved for customers which can be used to store
customized information. This patch provide an NVMEM interface
to support read out the customized data in OTP.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Qingwu Zhang <qingwu.zhang@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The bus_type field of v4l2_fwnode_endpoint structure passed as the argument
to v4l2_fwnode_endpoint_alloc_parse() function must be initiaized.
Set it to V4L2_MBUS_CSI2_DPHY, and check for -ENXIO which is returned
when the requested media bus type doesn't match the fwnode.
Also remove v4l2_fwnode_endpoint field from struct imx290 as it is only
needed in the probe function: use the local variable for this purpose.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The 10ms settle time is needed only at the end of all consecutive
register writes. So move the delay to outside of the for loop of
imx290_set_register_array().
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to enumerate all frame sizes supported by IMX290. This is
required for using with userspace tools such as libcamera.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX290 is capable of outputting frames in both Raw Bayer (packed) 10 and
12 bit formats. Since the driver already supports RAW10 mode, let's add
the missing RAW12 mode as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX290 operates with multiple link frequency and pixel rate combinations.
The initial driver used a single setting for both but since we now have
the lane count support in place, let's add configurable link frequency
and pixel rate.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX290 sensor can output frames with 2/4 CSI2 data lanes. This commit
adds support for 2 lane mode in addition to the 4 lane and also
configuring the data lane settings in the driver based on system
configuration.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,
- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,
- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The macro is defined as SET_RUNTIME_PM_OPS(suspend_fn, resume_fn, idle_fn),
so imx290_power_off must be the 1st arg, and imx290_power_on the 2nd.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
With the current driver 'media-ctl -p' issued right after the imx290 driver
is loaded prints:
pad0: Source
[fmt:unknown/0x0]
The format value of zero is due to the current_format field of the imx290
struct not being initialized yet.
As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field
is also initialized, so the line which set current_mode to a default value
in driver's probe() function is no longer needed.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As the ACPI id of ov2740 camera sensor was registered as "INT3474",
current ov2740 driver is supposed to be working with ACPI only.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the convenience function pm_runtime_get_if_active() instead of a
number of calls to runtime PM to figure out if the device was already
powered up.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When v4l2_async_register_subdev_sensor_common() returns
an error code, a pairing runtime PM usage counter
decrement is needed to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----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=KNAo
-----END PGP SIGNATURE-----
Merge tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Media documentation is now split into admin-guide, driver-api and
userspace-api books (a longstanding request from Jon);
- The media Kconfig was reorganized, in order to make easier to select
drivers and their dependencies;
- The testing drivers now has a separate directory;
- added a new driver for Rockchip Video Decoder IP;
- The atomisp staging driver was resurrected. It is meant to work with
4 generations of cameras on Atom-based laptops, tablets and cell
phones. So, it seems worth investing time to cleanup this driver and
making it in good shape.
- Added some V4L2 core ancillary routines to help with h264 codecs;
- Added an ov2740 image sensor driver;
- The si2157 gained support for Analog TV, which, in turn, added
support for some cx231xx and cx23885 boards to also support analog
standards;
- Added some V4L2 controls (V4L2_CID_CAMERA_ORIENTATION and
V4L2_CID_CAMERA_SENSOR_ROTATION) to help identifying where the camera
is located at the device;
- VIDIOC_ENUM_FMT was extended to support MC-centric devices;
- Lots of drivers improvements and cleanups.
* tag 'media/v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (503 commits)
media: Documentation: media: Refer to mbus format documentation from CSI-2 docs
media: s5k5baf: Replace zero-length array with flexible-array
media: i2c: imx219: Drop <linux/clk-provider.h> and <linux/clkdev.h>
media: i2c: Add ov2740 image sensor driver
media: ov8856: Implement sensor module revision identification
media: ov8856: Add devicetree support
media: dt-bindings: ov8856: Document YAML bindings
media: dvb-usb: Add Cinergy S2 PCIe Dual Port support
media: dvbdev: Fix tuner->demod media controller link
media: dt-bindings: phy: phy-rockchip-dphy-rx0: move rockchip dphy rx0 bindings out of staging
media: staging: dt-bindings: phy-rockchip-dphy-rx0: remove non-used reg property
media: atomisp: unify the version for isp2401 a0 and b0 versions
media: atomisp: update TODO with the current data
media: atomisp: adjust some code at sh_css that could be broken
media: atomisp: don't produce errs for ignored IRQs
media: atomisp: print IRQ when debugging
media: atomisp: isp_mmu: don't use kmem_cache
media: atomisp: add a notice about possible leak resources
media: atomisp: disable the dynamic and reserved pools
media: atomisp: turn on camera before setting it
...
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The IMX219 camera driver is not a clock provider, but merely a clock
consumer, and thus does not need to include <linux/clk-provider.h> and
<linux/clkdev.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
OminiVision ov2740 is a 2 megapixels RAW RGB image sensor which can
deliver 1920x1080@60fps frames. This driver add the support of
vertical blanking, exposure, test pattern, digital and analog gain
control for sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Qiu, Tianshu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Query the sensor for its module revision, and compare it
to known revisions.
Currently 2A and 1B revision indentification is supported.
[Sakari Ailus: Wrap a line over 80, alignment, use %u for printing u32]
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add match table, enable ov8856_probe() to support
both ACPI and DT modes.
ACPI and DT modes are primarily distinguished from
by checking for ACPI mode and by having resource like
be NULL.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Parse device properties and register controls for them using the newly
introduced helpers.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Parse device properties and register controls for them using the newly
introduced helpers.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Parse device properties and register controls for them using the newly
introduced helpers.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When enumerating the frame sizes, the value sent to
imx219_get_format_code should be fse->code
(the code from the ioctl) and not imx219->fmt.code
which is the code set currently in the driver.
Fixes: 22da1d56e9 ("media: i2c: imx219: Add support for RAW8 bit bayer format")
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement the get_selection pad operation for the IMX219 sensor driver.
The supported targets report the sensor's native size, the crop default
rectangle and the crop rectangle.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove vbi_regs_offset from a group of registers that are 888 specific,
include those registers names. Sources used for reference are 885 and 888
datasheets.
Add labels to some undocumented registers.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are *lots* of I2C ancillary drivers. While we're using
comments to group them, all options appear at the same menu.
It should be a lot clearer to group them into sub-menus, with
may help people to go directly to the driver(s) he's needing
to enable.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
v4l2_ctrl_handler_free() uses hdl->lock, which in ov5640 driver is set
to sensor's own sensor->lock. In ov5640_remove(), the driver destroys the
sensor->lock first, and then calls v4l2_ctrl_handler_free(), resulting
in the use of the destroyed mutex.
Fix this by calling moving the mutex_destroy() to the end of the cleanup
sequence, as there's no need to destroy the mutex as early as possible.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # v4.14+
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are some uAPI stuff that are driver-specific. Add them
to the main media uAPI body.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Right now, there are I2C drivers that don't depend on
camera support before and after those.
Move the camera support drivers to the end, and add
a notice at the "endif", in order to make easier to
maintain and to avoid adding extra dependencies at
the other i2c/*/Kconfig files.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are lots of drivers that only work when the media controller
and/or the V4L2 subdev APIs are present.
Right now, someone need to first enable those APIs before
using those drivers.
Well, ideally, drivers, should, instead *optionally*
depend on it, in order for PC camera drivers to be able to use
them, but nowadays most drivers are UVC cameras, with don't
require a sensor driver.
So, be it.
Let's instead make them select the MEDIA_CONTROLLER and the
SUBDEV API, in order to make easier for people to be able
of enabling them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix build fault when CONFIG_HWMON is a module, and CONFIG_VIDEO_I2C
as builtin. This is due to 'imply hwmon' in the respective Kconfig.
Issue build log:
ld: drivers/media/i2c/video-i2c.o: in function `amg88xx_hwmon_init':
video-i2c.c:(.text+0x2e1): undefined reference to `devm_hwmon_device_register_with_info
Cc: rdunlap@infradead.org
Fixes: acbea67989 (media: video-i2c: add hwmon support for amg88xx)
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As of `s5c73m3.h` the auto focus cluster in `s5c73m3_ctrls` has 5 and not 6
controls.
Signed-off-by: Sebastian Gross <sebastian.gross@emlix.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.
[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jacopo Mondi