The unlock_addr rework in kernel 2.6.25 breaks 16-bit SST chips. SST
39LF160 and SST 39VF1601 are both 16-bit only chip (do not have BYTE#
pin) and new uaddr value is not correct for them. Add
MTD_UADDR_0xAAAA_0x5555 for those chips. Tested with SST 39VF1601
chip.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When detecting a partition beyond the end of the device, skip most of
the initialisation, in particular those bits causing a division by zero.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Mostly simplifying the loops. Now everything fits into 80 columns,
is easier to read and the finer details have extra comments.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remaining are 12 warnings about long lines and 1 about braces that
could be argued about.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add_mtd_partition was a 150+ line monster consisting mostly of a single
loop. Seperate the loop from most of the body. Now it should be
obvious which variables are carried around from iteration to iteration.
Signed-off-by: Jörn Engel <joern@logfs.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A nice side effect of this patch is that the return value of
physmap_flash_suspend in the error path is the value of the first failing
suspend callback and not the bitwise OR of all of them.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't call suspend/resume functions if they have not been
defined.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Acked-By: Jörn Engel <joern@logfs.org>
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Existing CFI driver has problems with excessive writes during erase.
If CFI driver does many writes during one erase cycle we may face the
messages with -ETIMEO error on erase operation. It may cause the
following data corruption and kernel panics.
The reason of the issue is related to specifics of suspend operation:
if we write to flash during erase, suspend operation will cost some time
to erase procedure (for P30 it could be significant). In current version of
cfi driver the problem of many suspends is partially workarounded by adding
some time reserv to any operation (8xerase_time) but if we have many writes
during one erase the problem appears.
This patch detects the suspend and resets timer if suspend occured. It
has been well verified on different chips. No problems were found.
Could you please include the patch as it is simple and fixes bad issue.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With CONFIG_MTD_OF_PARTS=y I'm getting this new section mismatch in reference
from the function fsl_elbc_chip_probe() to the function
.devinit.text:of_mtd_parse_partitions()
This patch fixes the mismatch by providing __devinit annotation to the
fsl_elbc_chip_probe() function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix const to non-const pointer assignment in the MTD command line partitioning
driver.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use pr_debug(...) instead of printk(KERN_DEBUG ...) so that the message
is only printed when debugging is enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: John stoffel <john@stoffel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Such a hardcoded address can cause a checkstop or machine check if
the driver is in the kernel but the address is not acknowledged.
Both drivers allow an address to be specified as either a module
parameter or config option. Any future powerpc board should either
use one of these methods or find the address in the device tree.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove the Simtec BAST flash driver as this has been replaced by using
the platform flash driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.
Also remove mtd->ecclayout and mtd->oobavail assignments, mtd core
handles this all by itself.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.
Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.
But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.
This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:
OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.
To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no reason to prevent the Atmel NAND driver from
building as a module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ALE signal isn't correctly wired up to the ECC controller on the
AP7000, so it starts calculating ECC during the address cycles.
Work around this by resetting the ECC controller between the address and
data cycles.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This uses __raw_{read,write}s{b,w}() primitives to access data on NAND
chips for more efficient I/O.
On an arm926 with memory clocked at 100 MHz, this reduced the elapsed time
for a 64 MiB read by 16%. ("dd" /dev/mtd0 to /dev/null, with an 8-bit
NAND using hardware ECC and 128KiB blocksize.)
Also some minor section tweaks:
- Use platform_driver_probe() so no pointer to probe() lingers
after that code has been removed at run-time.
- Use __exit and __exit_p so the remove() code will normally be
removed by the linker.
Since these buffer read/write calls are new, this increases the runtime
code footprint (by 88 bytes on my build, after the section tweaks).
[haavard.skinnemoen@atmel.com: rebase onto atmel_nand rename]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use einfo, oinfo for the inner erase_info and otp_info structs used in
individual case statements.
drivers/mtd/mtdchar.c:582:26: warning: symbol 'info' shadows an earlier one
drivers/mtd/mtdchar.c:380:23: originally declared here
drivers/mtd/mtdchar.c:596:26: warning: symbol 'info' shadows an earlier one
drivers/mtd/mtdchar.c:380:23: originally declared here
drivers/mtd/mtdchar.c:704:19: warning: symbol 'info' shadows an earlier one
drivers/mtd/mtdchar.c:380:23: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The copy_to_user was casting away the address space to get the offset of
the length member. Use offsetof() instead and add it to the void __user
*argp.
drivers/mtd/mtdchar.c:527:23: warning: cast removes address space of expression
drivers/mtd/mtdchar.c:527:23: warning: incorrect type in argument 1 (different address spaces)
drivers/mtd/mtdchar.c:527:23: expected void [noderef] <asn:1>*to
drivers/mtd/mtdchar.c:527:23: got unsigned int *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Atmel serial flash tends to power up with the protection status bits set.
http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=4089
[michael.hennerich@analog.com: remove duplicate code]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make the atmel_nand driver selectable on AVR32, and update the Kconfig
help text to reflect this.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This fixes several bugs in the atmel_nand_probe() error path, including
at least one memory leak.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The AT91 NAND driver needs just a few tiny modifications to work on
AVR32 as well. Rename it atmel_nand to reflect this.
Also move the ECC register definitions into drivers/mtd/nand since they
are only useful to the atmel_nand driver, and get rid of the useless
filename at the top of each file.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
No point in using an AT91-specific GPIO API when the generic API works
just as well.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
WARNING: drivers/mtd/nand/built-in.o(.devinit.text+0x114): Section mismatch
in reference from the function fsl_elbc_ctrl_probe() to the function
.devexit.text:fsl_elbc_ctrl_remove()
__devinit functions should not call functions with __devexit. Since probe
function calls remove in case of errors, we want to remove __devexit
attribute from it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Although if people have questions about ARCnet, perhaps it's _better_
for them to be mailing dwmw2@cam.ac.uk about it...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix nandsim build error, missing #include:
linux-next-20080605/drivers/mtd/nand/nandsim.c: In function 'divide':
linux-next-20080605/drivers/mtd/nand/nandsim.c:462: error: implicit declaration of function 'do_div'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Now it returns the 0 if cmdlineparse not supplied.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The changelog on the driver is superflous given this
is being kept under revision control. Remove the other
cruft in the header and update the copyright and the
supported device list.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a minor problem with what should have been
debug output by changing printk() to dev_dbg()
inside s3c2410_nand_update_chip().
Thanks to David Woodhouse for pointing this out.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Handle the case where flash memory and ethernet mac/phy are mapped onto
the same async bank
[try #4]
- drop superfluous casts
- drop SSYNC() when reading from the flash and rewrite
bfin_copy_from() to be like bfin_copy_to() so that
we dont have to handle all the aligned/unaligned cases
[try #3] rename bf5xx-flash to bfin-async-flash
- move all kconfig board settings into board resources
- fixup casting style according to lkml feedback
- rewrite driver so that it can handle arbitrary of
instances according to the declared platform resources
[try #2]
Remove useless SSYNC() as Will said
[try #1]
The BF533-STAMP does this for example.
All board-specific configuration goes in your board resources file.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Acked-By: Jörn Engel <joern@logfs.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Janitorial work to remove temporary pointers and make some functions a bit
more readable.
Signed-off-by: Chris Malley <mail@chrismalley.co.uk>
Reviewed-By: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Amend nandsim so that it does not assume 32-bit flash size.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
To get the correct information in case of power off recovery,
it should read ECC status first
Also remove previous workaround method.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- Add support for binary page size DataFlashes.
- The driver now prints out pagesize and erasesize.
Printout valuable information for creating flash filesystems.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Yoichi Yuasa