include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull input layer fixes from Dmitry Torokhov:
"Just a few fixups to a couple of drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - ignore signals when finishing updating firmware
Input: elan_i2c - clear INT before resetting controller
Input: atmel_mxt_ts - add T100 as a readable object
Input: edt-ft5x06 - increase allowed data range for threshold parameter
Use wait_for_completion_timeout() instead of
wait_for_completion_interruptible_timeout() to avoid stray signals ruining
firmware update. Our timeout is only 300 msec so we are fine simply letting
it expire in case device misbehaves.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some old touchpad FWs need to have interrupt cleared before issuing reset
command after updating firmware. We clear interrupt by attempting to read
full report from the controller, and discarding any data read.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When using the 'object' sysfs attribute, T100 is not displayed in
the output.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The datasheet and application note does not mention an allowed range for
the M09_REGISTER_THRESHOLD parameter. One of our customers needs to set
lower values than 20 and they seem to work just fine on EDT EP0xx0M09 with
T5x06 touch.
So, lacking a known lower limit, we increase the range for thresholds,
and set the lower limit to 0. The documentation is updated accordingly.
Signed-off-by: Schoefegger Stefan <stefan.schoefegger@ginzinger.com>
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull some more input subsystem updates from Dmitry Torokhov:
"An updated xpad driver with a few more recognized device IDs, and a
new psxpad-spi driver, allowing connecting Playstation 1 and 2 joypads
via SPI bus"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cros_ec_keyb - remove extraneous 'const'
Input: add support for PlayStation 1/2 joypads connected via SPI
Input: xpad - add USB IDs for Mad Catz Brawlstick and Razer Sabertooth
Input: xpad - sync supported devices with xboxdrv
Input: xpad - sort supported devices by USB ID
One of Elan modules with sample version is 0x74 and hw_version is 0x03 has
a bug in absolute mode implementation, so let it run in default PS/2
relative mode.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer Elantech hardware requires different way of fetching chip type and
version data.
Signed-off-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before trying to properly initialize the touchpad and generate bunch of
errors, let's first see it there is anything at the given address. If we
get error, fail silently with -ENXIO.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
Instead of specifying type explicitly, derive it from the type of pointer
when allocating memory, which is considered safer practice.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use seq_puts() when printing a string which does not contain a data format
specification.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using seq_putc() when printing a single character '0'.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PlayStation 1/2 joypads can be connected directly to the SPI interface.
Signed-off-by: Tomohiro Yoshidomi <sylph23k@gmail.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add USB IDs for two more Xbox 360 controllers.
I found them in the pull requests for the xboxdrv userspace driver, which
seems abandoned.
Thanks to psychogony and mkaito for reporting the IDs there!
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The userspace xboxdrv driver [0] contains some USB IDs unknown to the
kernel driver. I have created a simple script [1] to extract the missing
devices and add them to xpad.
A quick google search confirmed that all the new devices called
Fightstick/pad are Arcade-type devices [2] where the
MAP_TRIGGERS_TO_BUTTONS option should apply.
There are some similar devices in the existing device table where this
flag is not set, but I did refrain from changing those.
[0] https://github.com/xboxdrv/xboxdrv/blob/stable/src/xpad_device.cpp
[1] http://codepad.org/CHV98BNH
[2] https://www.google.com/search?q=SFxT+Fightstick+Pro&tbm=isch
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some entries in the table of supported devices are out of order.
To not create a mess when adding new ones using a script, sort them first.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware drivers
from Google, more auxdisplay drivers, extcon drivers, fpga drivers, and
a bunch of other driver updates. Nothing major, except if you happen to
have the hardware for these drivers, and then you will be happy :)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvAgg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yknsACgzkAeyz16Z97J3UTaeejbR7nKUCAAoKY4WEHY
8O9f9pr9gj8GMBwxeZQa
=OIfB
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
Core changes
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources.
I have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements
- A whole slew of drivers have their spinlocks chaned to raw spinlocks
as they provide irqchips, and thus we are progressing on realtime
compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot.
-----BEGIN PGP SIGNATURE-----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=DGPb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.12 kernel cycle.
Core changes:
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources. I
have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers:
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements:
- A whole slew of drivers have their spinlocks chaned to raw
spinlocks as they provide irqchips, and thus we are progressing on
realtime compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot"
* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: f7188x: Add a missing break
gpio: omap: return error if requested debounce time is not possible
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
gpio: gpio-wcove: fix GPIO IRQ status mask
gpio: DT bindings, move tca9554 from pcf857x to pca953x
gpio: move tca9554 from pcf857x to pca953x
gpio: arizona: Correct check whether the pin is an input
gpio: Add XRA1403 DTS binding documentation
dt-bindings: add exar to vendor prefixes list
gpio: gpio-wcove: fix irq pending status bit width
gpio: dwapb: use dwapb_read instead of readl_relaxed
gpio: aspeed: Add open-source and open-drain support
gpio: aspeed: Add debounce support
gpio: aspeed: dt: Add optional clocks property
gpio: aspeed: dt: Fix description alignment in bindings document
gpio: mvebu: Add limited PWM support
gpio: Use unsigned int for interrupt numbers
gpio: f7188x: Add F71889A GPIO support.
gpio: core: Decouple open drain/source flag with active low/high
gpio: arizona: Correct handling for reading input GPIOs
...
Pull input subsystem updates from Dmitry Torokhov:
- a big update from Mauro converting input documentation to ReST format
- Synaptics PS/2 is now aware of SMBus companion devices, which means
that we can now use native RMI4 protocol to handle touchpads, instead
of relying on legacy PS/2 mode.
- we removed support from BMA180 accelerometer from input devices as it
is now handled properly by IIO
- update to TSC2007 to corretcly report pressure
- other miscellaneous driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (152 commits)
Input: ar1021_i2c - use BIT to check for a bit
Input: twl4030-pwrbutton - use input_set_capability() helper
Input: twl4030-pwrbutton - use correct device for irq request
Input: ar1021_i2c - enable touch mode during open
Input: add uinput documentation
dt-bindings: input: add bindings document for ar1021_i2c driver
dt-bindings: input: rotary-encoder: fix typo
Input: xen-kbdfront - add module parameter for setting resolution
ARM: pxa/raumfeld: fix compile error in rotary controller resources
Input: xpad - do not suggest writing to Dominic
Input: xpad - don't use literal blocks inside footnotes
Input: xpad - note that usb/devices is now at /sys/kernel/debug/
Input: docs - freshen up introduction
Input: docs - split input docs into kernel- and user-facing
Input: docs - note that MT-A protocol is obsolete
Input: docs - update joystick documentation a bit
Input: docs - remove disclaimer/GPL notice
Input: fix "Game console" heading level in joystick documentation
Input: rotary-encoder - remove references to platform data from docs
Input: move documentation for Amiga CD32
...
The MSB for the first byte of touch data transmission is always 1. Make
it a little more obvious we're testing this bit by using BIT(7).
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cleanup driver slightly by using input_set_capability() instead
of manually setting the required bits.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The interrupt should be requested for the platform device
and not for the input device.
Fixes: 7f9ce649d2 ("Input: twl4030-pwrbutton - simplify driver using devm_*")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device could as well be in command mode, in which this driver cannot
handle the device. When opening the device, let's make sure the device
will be in the mode we expect it to be for this driver.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fix from Dmitry Torokhov:
"Yet another quirk to i8042 to get touchpad recognized on some laptops"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Clevo P650RS to the i8042 reset list
These tests are meaningless as is because "adapt" can't possibly be both
less than 1 and greater than 32.
Fixes: d81ca730e3 ("input: touchscreen: mxs-lradc: Add support for touchscreen")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Clevo P650RS and other similar devices require i8042 to be reset in order
to detect Synaptics touchpad.
Reported-by: Paweł Bylica <chfast@gmail.com>
Tested-by: Ed Bordin <edbordin@gmail.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=190301
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixlet from Dmitry Torokhov:
"An update to Elan PS/2 driver to allow working on yet another
Lifebook"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add Fujitsu Lifebook E547 to force crc_enabled
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/input/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cc: linux-input@vger.kernel.org
Add a parameter for setting the resolution of xen-kbdfront in order to
be able to cope with a (virtual) frame buffer of arbitrary resolution.
While at it remove the pointless second reading of parameters from
Xenstore in the device connection phase: all parameters are available
during device probing already and that is where they should be read.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Temporary got a Lifebook E547 into my hands and noticed the touchpad
only works after running:
echo "1" > /sys/devices/platform/i8042/serio2/crc_enabled
Add it to the list of machines that need this workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Thorsten Leemhuis <linux@leemhuis.info>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Just a small update to xpad driver to recognize yet another gamepad,
and another change making sure userio.h is exported"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add support for Razer Wildcat gamepad
uapi: add missing install of userio.h
The polled firmware update proved unreliable when testing on S7817. Use
attention to signal commands are complete.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The data in F12_2D_Ctrl8 corresponds to the inactive border width used by
the RMI device. It is not in pixel units and should not be treated as a
clip value.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When IRQ handling was moved to rmi_driver in 3aeed5b the naming of the
interrupt changed from "rmi4_i2c" to "2-0020" (or similar). This patch
restores the previous behaviour and makes the interrupt easier to identify
in /proc/interrupts.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ar1021_i2c also supports the ar1020 device I'm using. This is tested.
They also share the same datasheet:
http://ww1.microchip.com/downloads/en/DeviceDoc/40001393C.pdf
So let users see that they have a compatible in front of them by adding
AR1020 to the driver's description.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not be forcing edge triggered interrupt, but rather let platform
decide the kind of trigger it needs to use. Also, the driver is not quite
safe with regard to edge-triggered interrupts as it does not try to kick
the controller after requesting/enabling IRQ.
Reviewed-By: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The name field in structure i2c_device_id is 20 characters, and we expect
it to be NULL-terminated, however we are trying to stuff it with 21 bytes
and thus NULL-terminator is lost. This causes issues when one creates
device with name "MICROCHIP_AR1021_I2C" as i2c core cuts off the last "C",
and automatic module loading by alias does not work as result.
The -I2C suffix in the device name is superfluous, we know what bus we are
dealing with, so let's drop it. Also, no other driver uses capitals, and
the manufacturer name is normally not included, except in very rare cases
of incompatible name collisions.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=116211
Fixes: dd4cae8bf1 ("Input: Add Microchip AR1021 i2c touchscreen")
Reviewed-By: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the common kernel coding style and corrently align parameters with
open parenthesis.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_prepare_enable() may fail, so we better check its return value and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If imx6ul_tsc_init() fails we should not return directly.
We should disable the previously acquired clocks in this case.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Motorola CPCAP is a PMIC found in multiple smartphones.
This driver adds support for the power/on button and has
been tested in Droid 4.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
According to the previous error handling code, it is likely that 'goto
err_free_keymap' is expected here in order to avoid a memory leak in error
handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are several quirky Xbox One pads that depend on initialization
packets that the Microsoft pads don't require. To deal with these,
I've added a mechanism for issuing device-specific initialization
packets using a VID/PID-based quirks list.
For the initial set of init quirks, I have added quirk handling from
Valve's Steam Link xpad driver[0] and the 360Controller project[1] for
macOS to enable some new pads to work properly.
This should enable full functionality on the following quirky pads:
0x0e6f:0x0165 - Titanfall 2 gamepad (previously fully non-functional)
0x0f0d:0x0067 - Hori Horipad (analog sticks previously non-functional)
0x24c6:0x541a - PowerA Xbox One pad (previously fully non-functional)
0x24c6:0x542a - PowerA Xbox One pad (previously fully non-functional)
0x24c6:0x543a - PowerA Xbox One pad (previously fully non-functional)
[0]: https://github.com/ValveSoftware/steamlink-sdk/blob/master/kernel/drivers/input/joystick/xpad.c
[1]: https://github.com/360Controller/360Controller
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
sparse says
warning: incorrect type in assignment (different base types)
expected unsigned short [unsigned] [usertype] offset
got restricted __be16 [usertype] <noident>
for every usage of cpu_to_be16 in yealink.c. Defining it __be16 in the
first place shouldn't hurt.
Signed-off-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Henk.Vergonet@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When submitting the support for the ACPI0011 windows tablet keys device I
mapped the "windows" logo homekey to KEY_HOMEPAGE. But this is inconsistent
with how it is done on windows tablets using the old PNP0C40 ACPI device
and it does not match the HUT spec, which says that usage-page 7 usage 0xe3
is "Keyboard Left GUI".
This commit maps usage-page 7 usage 0xe3 to KEY_LEFTMETA fixing this.
Fixes: 4c3362f449 ("Input: soc_button_array - add support for ACPI 6.0...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add pm8xxx_regs for this PMIC and the device tree match table entry.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some PMIC vibrator IPs use a separate enable register to turn the
vibrator on and off. To detect if a vibrator uses this feature, rely on
the enable_mask being non-zero.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to prepare this driver to support other vibrators of the same
kind, move some hardcoded values to a structure holding register
parameters (address, mask, shit of the control register).
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
sparse says:
sur40.c:372:40: warning: restricted __le32 degrades to integer
the header's data is __le32 so we need to convert it before comparing.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gpiod API allows standard way of specifying GPIO polarity and takes it into
account when reading or setting GPIO state. It also allows us to switch to
common way of obtaining GPIO descriptor and away form legacy platform data.
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of keying interrupt trigger off GPIO polarity, let's rely on
platform code to set it up properly for us.
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of having standard interrupt handler and manually firing work item
to perform I2C reads, let's switch to threaded interrupts, which were
designed specifically for this purpose.
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are reading GPIO state in a non-atomic context (workqueue), so we can
use "cansleep" variant, and thus make the driver available on systems where
GPIO controllers require sleeping when reading GPIO state.
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of expecting that GPIO is always interrupt source, let's use
interrupt specified in I2C client.
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of manually converting big endian data on wire into host
endianness, let's use helpers to do that for us. It might save us
a few cycles if host endianness matches what's on wire.
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are not registering drivers, but transport devices (AKA sensors), so
let's call them that.
Also let's rename "retval" to "error" in probe() functions as the variables
are used to store error codes.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no reason to copy structures field-by-filed when we can copy
elements at once.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mapping table holds address in LE form, so we should convert it
to CPU when comparing it.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If rmi_enable_sensor() fails in rmi_driver_probe(), we should not return
immediately, but disable IRQs and tear down function list.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The rest of the kernel uses u8, u16, etc for data coming form hardware,
let's switch ti using u8 here as well.
Also turn pkt_type into an enum.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's stop using -1 as a universal return value and instead propagate
errors from underlying calls up the stack.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use standard infrastructure, such as BIT and GENMASK, instead of rolling
bitmasks by hand.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out querying and parsing 3-byte response into an integer value.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that i2c_client_type structure is exported, we can use it, instead
of i2c_adapter_type, when looking for devices that are i2c clients.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY4ZYkAAoJEHm+PkMAQRiGsq4H/R4PMXDoe2XhSSk7IoT97pXV
/A8np/scAPjzEgYUidbb54OSqWwsPRuPGWONTFeSrE2u0L4wln/REI91jg7QetLq
IisncExlYeJ/XQ+iO0ZZh9fLbqwIlEJFdSXmyIFr3m/TBxe8a61C8j93oNgM1tHT
yuwzlq7c3sLq2hsmUG2HyL2kJsEfRasv4Rk0yhFuti12zVsBoTW4qmZuMauq+gdf
f7cSYgiHhPTdb2o+azg5O7uYNHaQQBxdUMlIuhhYtVOUq+pFDO23SLHSFIW2NwOm
Zn5R6CFSrLsCw0Bx0v8Xlc151QUbaRK4h9lhUhkBr6d3uNShU1NQ9JojpSvYwBo=
=vP6E
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rc5' into next
Sync up with mainline to bring in changes to input subsystem merged
through other trees.
Some form factors (detachables/tablets) may not have a keyboard and
thus user may have to resort to using a defined EC UI to send sysrq(s)
to the kernel in order to collect crash info etc. This UI typically
is in the form of user pressing volume / power buttons in some specific
sequence and for some specific time. Add a new EC event that allows EC
to communicate the sysrq to the AP.
(We're skipping event number 5 because it has been reserved for
something else)
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When trying to destroy platform data after destruction of SMbus companion,
we need to make sure that we are actually dealing with an SMB companion
device, and not some random I2C client device.
Fixes: 8eb92e5c91 ("Input: psmouse - add support for SMBus companions")
Reported-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This essentially reverts commit baf28d91e7 ("Input: bma150 - avoid
binding to bma180 if IIO bma180 driver present") and commit ef3714fdbc
("Input: bma150 - extend chip detection for bma180")
Rationale: initially (2012) the GTA04 device using a bma180 chip simply
referenced the bma150 platform driver in its board file [1] which happened
to work in all scenarios that were tested.
When conversion to DT started (2014), we needed to make the driver be still
recognised. Hence we introduced the compatibility to the bma180 chip in
Linux 3.15-rc5 [2] without further checks if it is really 100% compatible.
This worked flawlessly for years with the GTA04 device.
Recently (2016), Hans de Goede pointed out that the chips are not as
similar as they appeared and the driver works with the bma180 for the GTA04
only by good luck. He proposed to remove the bma180 support completely [3],
but we still did need it until we have a replacement. Thus, a conditional
compile was added.
We have now developed a generic iio-input-bridge which works with any 2 or
3 axis iio based accelerometer. It has been tested on GTA04 and Pyra and
works as expected. Therefore we can remove the bma180 support from this
driver completely. User-space API compatibility can be restored by using
the iio-input-bridge.
Maybe it is time to convert the bma150 driver to iio as well and retire the
accelerometer input drivers completely but this is a different story and
task.
[1]: https://github.com/neilbrown/linux/blob/gta04/3.2.y/arch/arm/mach-omap2/board-omap3gta04.c#L976
[2]: https://patchwork.kernel.org/patch/3961171/
[3]: https://patchwork.kernel.org/patch/9325481/
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Added missing of_match_table for max11801_ts driver with compatible as
"maxim,max11801_ts"
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gpio-matrix-keypad driver normally sets inactive columns as inputs
while scanning. This does not work for all hardware, which may require
the inactive columns to be actively driven in order to overcome any
pull-ups/downs on the columns.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Try a quick read from the device in mip4_query_device() to make sure
that the device is there, as we do not consider failures to retrieve
product name or resolution fatal.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Each time the HWMON devices are read (e.g. battery voltage) while the
touchscreen is held pressed, extra pen-up and pen-down events are
generated. This is fixed by avoiding the UP event when the touchscreen is
stopped.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most of the Synaptics devices are connected through PS/2 and a different
bus (SMBus or HID over I2C). The secondary bus capability is indicated by
the InterTouch bit in extended capability 0x0C.
We only enable the InterTouch device to be created for the laptops
registered with the top software button property or those we know that are
functional. In the future, we might change the default to always rely on
the InterTouch bus. Currently, users can enable/disable the feature with
the psmouse parameter synaptics_intertouch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation for SMBus/Intertouch device support, move static device
information that we query form the touchpad upon initialization into
separate structure. This will allow us to query the device without
allocating memory first.
Also stop using "unsigned long", everything fits into 32 bit chunks.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This provides glue between PS/2 devices that enumerate the RMI4 devices
and Elan touchpads to the RMI4 (or Elan) SMBus driver.
The SMBus devices keep their PS/2 connection alive. If the initialization
process goes too far (psmouse_activate called), the device disconnects
from the I2C bus and stays on the PS/2 bus, that is why we explicitly
disable PS/2 device reporting (by calling psmouse_deactivate) before
trying to register SMBus companion device.
The HID over I2C devices are enumerated through the ACPI DSDT, and
their PS/2 device also exports the InterTouch bit in the extended
capability 0x0C. However, the firmware keeps its I2C connection open
even after going further in the PS/2 initialization. We don't need
to take extra precautions with those device, especially because they
block their PS/2 communication when HID over I2C is used.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Prepare PS/2 mouse drivers to work with devices that are accessible both
via PS/2 and SMBus, which provides higher bandwidth, and thus suits better
for modern multi-touch devices.
We expect that SMBus drivers will take control over the device, so when
we detect SMBus "protocol" we forego registering input device, or enabling
PS/2 device reports (as it usually makes device unresponsive to access over
SMBus).
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of storing only protocol "type" in pmsouse structure, store pointer
to the protocol structure, so that we have access to more data without
having to copy it over to psmouse structure.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of serio's fast reconnect option and allow psmouse protocol
handler's to implement fast reconnect handlers that will be called during
system resume.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devices connected to serio bus are quite slow, and to improve apparent
speed of resume process, serio core resumes (reconnects) its devices
asynchronously, by posting port reconnect requests to a workqueue.
Unfortunately this means that if there is a dependent device of a given
serio port (for example SMBus part of touchpad connected via both PS/2 and
SMBus), we do not have a good way of ensuring resume order.
This change allows drivers to define "fast reconnect" handlers that would
be called in-line during system resume. Drivers need to ensure that these
handlers are truly "fast".
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Fixes to various USB drivers to validate existence of endpoints before
trying to use them, fixes to APLS v8 protocol, and a couple of i8042
quirks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ALPS - fix trackstick button handling on V8 devices
Input: ALPS - fix V8+ protocol handling (73 03 28)
Input: sur40 - validate number of endpoints before using them
Input: kbtab - validate number of endpoints before using them
Input: hanwang - validate number of endpoints before using them
Input: yealink - validate number of endpoints before using them
Input: ims-pcu - validate number of endpoints before using them
Input: cm109 - validate number of endpoints before using them
Input: iforce - validate number of endpoints before using them
Input: elan_i2c - add ASUS EeeBook X205TA special touchpad fw
Input: i8042 - add TUXEDO BU1406 (N24_25BU) to the nomux list
Input: synaptics-rmi4 - prevent null pointer dereference in f30
Input: i8042 - add noloop quirk for Dell Embedded Box PC 3000
Let's stop using !!x to reduce value of trackstick button expression to 0/1
and use shift instead. This removes the following sparse warning:
CHECK drivers/input/mouse/synaptics.c
drivers/input/mouse/synaptics.c:943:79: warning: dubious: !x | y
Also, the bits we are testing are not capabilities, so lets drop "_CAP"
suffix from macro names.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
The compatible strings don't have a vendor prefix because that's how it's
used currently, and changing this will be a Device Tree ABI break.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
As pointed by Hans de Goede, there's no mssl1680 and this is just used in
some ACPI systems to identify the gsl1680 chip. So isn't included in the
OF device ID table since a DT should use the proper device name instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper in evdev, joydev and mousedev. The helper
replaces a common pattern by taking the proper reference against the
parent device and adding both the cdev and the device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/input
Prior to this patch, there were 8 uses of pr_warning and
17 uses of pr_warn in drivers/input
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Alps stick devices always have physical buttons, so we should not check
ALPS_BUTTONPAD flag to decide whether we should report them.
Fixes: 4777ac220c ("Input: ALPS - add touchstick support for SS5 hardware")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Pali Rohar <pali.rohar@gmail.com>
Tested-by: Paul Donohue <linux-kernel@PaulSD.com>
Tested-by: Nick Fletcher <nick.m.fletcher@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devices identified as E7="73 03 28" use slightly modified version of V8
protocol, with lower count per electrode, different offsets, and different
feature bits in OTP data.
Fixes: aeaa881f9b ("Input: ALPS - set DualPoint flag for 74 03 28 devices")
Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com>
Acked-by: Pali Rohar <pali.rohar@gmail.com>
Tested-by: Paul Donohue <linux-kernel@PaulSD.com>
Tested-by: Nick Fletcher <nick.m.fletcher@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Windows 10 tablets with gpio buttons will typically use the ACPI 6.0
Generic Button Device with a HID of ACPI0011 for these buttons.
The ACPI description for these in the ACPI0011 devices _DSD object uses
something resembling HID descriptors, except that instead of indicating
a bit index into a HID input report, the index indicates the _CRS index
for the GPIO.
The use of 1 interrupt per button, some of which need to be wakeup
sources, instead of using input reports makes it impossible to use the
HID subsystem for this.
This really is just another gpio-keys input device with the platform
data described in ACPI, so this commit adds parsing for this new way
to describe gpio-keys to the soc_button_array driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Count how much gpio_keys we actually need, this is a preparation patch
for adding support for the new Win10 / ACPI-6.0 "Generic Buttons Device"
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40... ")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 3.13
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: bba5394ad3 ("Input: add support for Hanwang tablets")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.37
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: aca951a22a ("[PATCH] input-driver-yealink-P1K-usb-phone")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.14
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack control-interface endpoints.
Fixes: 628329d524 ("Input: add IMS Passenger Control Unit driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915 ("Input: add driver for USB VoIP phones with CM109...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 2.6.28
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since gpiod_count() does not return 0 anymore, we don't need to shadow
its error code and would safely propagate to the user.
While here, replace second parameter by NULL in order to prevent side
effects on _DSD enabled firmware.
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the code to use devm_* API so that driver core will manage
resources.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
EeeBook X205TA is yet another ASUS device with a special touchpad
firmware that needs to be accounted for during initialization, or
else the touchpad will go into an invalid state upon suspend/resume.
Adding the appropriate ic_type and product_id check fixes the problem.
Signed-off-by: Matjaz Hegedic <matjaz.hegedic@gmail.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TUXEDO BU1406 does not implement active multiplexing mode properly,
and takes around 550 ms in i8042_set_mux_mode(). Given that the
device does not have external AUX port, there is no downside in
disabling the MUX mode.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Suggested-by: Vojtech Pavlik <vojtech@suse.cz>
Reviewed-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the platform data has f30_data.disable set, f30 in rmi_f30_config()
might be null. Prevent a kernel oops by checking for non-null f30.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gpiolib-acpi code is becoming more strict and connection-IDs
may only be used with devices which have a _DSD with matching IDs
in there. Since the soc_button_array ACPI binding is pure index
based pass in NULL as connection-ID to avoid the more strict cheks
resulting in gpiod_count and gpiod_get_index not returning any gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some systems (Intel tablets with axp288 pmic) the powerbutton is
also connected to a gpio pin of the SoC, advertised through the
"INTCFD9" / "PNP0C40" acpi device. This leads to double reporting
of powerbutton events, which is undesirable, so one driver needs
to not report input events in this case.
Since the soc_button_array driver for the "PNP0C40" acpi device
also handles wake from suspend on these tablets and since the
axp20x-pel driver requires relative expensive i2c accrsses,
it is best for the axp20x-pek driver to not register an input device
in this case.
Note that this commit leaves the axp20x-driver bound to the
device, rather then returning -ENODEV, this is done so that the
sysfs attributes it offers are kept around.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all input device related initialization into a new
axp20x_pek_probe_input_device helper function.
This introduces one functional change, the input device is now
registered before the sysfs attr get registered. This is not a problem
as the sysfs attr are to configure some long press settings (forced
poweroff) in the hardware and do not interact with the input_device.
This is a preparation patch for not always registering the input dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before this commit axp20x-pek was mixing 2 style error reporting calls:
dev_err(&pdev->dev, ...);
dev_err(axp20x->dev, ...);
But the second is our parent device, not our own device, so switch to
using &pdev->dev everywhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the driver is using generic device properties, it should work
properly when CONFIG_OF is turned off. This patch removes the
ifdef CONFIGOF and make sure the driver always have of_match_table.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some platform drivers use devm_input_allocate_device() together with
sparse_keymap_setup() in their .probe callbacks. While using the former
simplifies error handling, using the latter necessitates calling
sparse_keymap_free() in the error path and upon module unloading to
avoid leaking the copy of the keymap allocated by sparse_keymap_setup().
To help prevent such leaks and enable simpler error handling, make
sparse_keymap_setup() use devm_kmemdup() to create the keymap copy so
that it gets automatically freed.
This works for both managed and non-managed input devices as the keymap
is freed after the last reference to the input device is dropped.
Note that actions previously taken by sparse_keymap_free(), i.e. taking
the input device's mutex and zeroing its keycode and keycodemax fields,
are now redundant because the managed keymap will always be freed after
the input device is unregistered.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Extend the pwm-beeper driver to support customized frequency for SND_BELL
from device properties.
Signed-off-by: Guan Ben <ben.guan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sort all devices in alps_model_data by signature and remove
command_mode_resp which is not used anymore.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Support for devices with ALPS_PROTO_V9 is not implemented yet but we can
detect these alps touchpads and warn users about it.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Like for other protocols create alps_v4_protocol_data and use it in
alps_identify() function.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The aux port does not get detected without noloop quirk, so external PS/2
mouse cannot work as result.
The PS/2 mouse can work with this quirk.
BugLink: https://bugs.launchpad.net/bugs/1591053
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
INPUT_PROP_BUTTONPAD is currently only set through the platform data.
The RMI4 header doc says that this property is there to force the
buttonpad property, so we also need to detect it by looking at
the exported buttons count.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of manipulating capabilities bits of input device directly, let's
use input_set_capability() API.
Also, stop setting ABS_X/Y bits explicitly as input_set_abs_params() does
this for us.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have switched the driver to use generic device properties API, so there
is no need to check for presence of DT node before trying parse properties.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the switch to devm, there is no need for ad7879_probe() to return the
touchscreen structure, we can use plain error code. This also fixes issue
introduced with devm concersion, where we returned 0 on success (which
worked OK since IS_ERR(0) would not trigger, but was not correct
regardless).
Fixes: 381f688eee3d ("Input: ad7879 - use more devm interfaces")
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The conversion to devm accidentally removed setting up of I2C client data
upon successful probe of the touchscreen. Let's move this setting into the
core, so we do not forger about it again.
Fixes: 381f688eee3d ("Input: ad7879 - use more devm interfaces")
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to tread the same register twice in a row.
Fixes: ea4348c846 ("Input: tca8418_keypad - hide gcc-4.9 -Wmaybe-un ...")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using regmap this is no longer required.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Up until now only platforms using legacy platform data were able to switch
AUX/VBAT/GPIO pin in GPIO mode and use it as regular GPIO line. Let's
allow platforms using generic device properties to do the same.
Reviewed-by: Michael Hennerich <michael.hennerich@analog.com>
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gpiochip_add now has a managed version, and we can remove sysfs attribute
group via devm_add_action_or_reset (at least until we have devm version of
sysfs_create_group). This allows us to get rid of ad7879_remove().
Reviewed-by: Michael Hennerich <michael.hennerich@analog.com>
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of rolling our own infrastructure to provide uniform access to I2C
and SPI buses, let's switch to using regmap.
Reviewed-by: Michael Hennerich <michael.hennerich@analog.com>
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do.
This is a treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace
ABI correctly reflect the current in-kernel consumer of a pin
taken using this abstraction. This is a treewide change also
updating all users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide
change also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing
a backend into the pin control subsystem that were also merged
into the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace
to fully test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime
PM support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations.
-----BEGIN PGP SIGNATURE-----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=O81I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
Previously, tsc2007 would report as ABS_PRESSURE:
0 for no pressure (resistance infinite)
high value for soft pressure (high resistance)
low value for firm pressure (lower resistance)
This does not matter for most applications (e.g. GUI, Menu, Scrolling etc.)
where the ABS_PRESSURE is ignored and only BTN_TOUCH is processed to detect
screen taps.
Only some special graphics applications read the pressure channel and they
will be mixed up by this non-monotonic relation.
So we fix it to become:
0 for no pressure (resistance infinite)
low value for soft pressure (high resistance)
high value for firm pressure (lower resistance)
While this patch changes the values reported to userspace, ABS_PRESSURE is
used rarely by userspace. Most software only relies on BTN_TOUCH (boolean),
which is not affected by this patch. Some graphics software makes use of
the interface and does not work correctly with the currently used inverted
behaviour.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename tsc2007_calculate_pressure to tsc2007_calculate_resistance because
that is what it does.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/input/touchscreen/zet6223.ko | grep alias
alias: i2c:zet6223
After this patch:
$ modinfo drivers/input/touchscreen/zet6223.ko | grep alias
alias: of:N*T*Czeitec,zet6223C*
alias: of:N*T*Czeitec,zet6223
alias: i2c:zet6223
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The tsc2007 chip not only has a resistive touch screen controller but
also an external AUX adc imput which can be used for an ambient
light sensor, battery voltage monitoring or any general purpose.
Additionally it can measure the chip temperature.
This extension provides an iio interface for these adc channels.
Since it is not wasting much resources and is very straightforward,
we simply provide all other adc channels as optional iio interfaces
as weel. This can be used for debugging or special applications.
This patch also splits the tsc2007 driver in several source files:
tsc2007.h -- constants, structs and stubs
tsc2007_core.c -- functional parts of the original driver
tsc2007_iio.c -- the optional iio stuff
Makefile magic allows to conditionally link the iio stuff
if CONFIG_IIO=y or =m in a way that it works with
CONFIG_TOUCHSCREEN_TSC2007=m.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
1. check if chip is really present and don't succeed if it isn't.
2. if it succeeds, power down the chip until accessed
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ELAN0605 has been confirmed to be a variant of ELAN0600, which is
blacklisted in the hid-core to be managed by elan_i2c. This device can be
found in Lenovo ideapad 310s (80U4000).
Signed-off-by: Hiroka IHARA <ihara_h@live.jp>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of supporting legacy platform data (of which we have no mainline
users) and OF-based properties, let's switch to generic device properties.
This will still allow legacy boards to use the driver (by defining property
sets and attaching them to the drivers) and will simplify probe and make
driver usable on ACPI-based systems as well.
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In case of an optional regulator missing, regulator core will return
ERR_PTR(-ENOENT) and not NULL, so the check for missing regulator is
incorrect. Also, the regulator is not optional, it may simply be missing
from platform description, so let's use devm_regulator_get() and rely on
regulator core to give us dummy supply when real one is not available.
Fixes: d257f2980f ("Input: tsc2005 - convert to gpiod")
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To be prepared for SPI module loading using full compatible strings from
device tree, let's add OF module device table data.
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a basic driver for the Zeitec ZET6223 I2C touchscreen
controllers. The driver does not support firmware loading, which is not
required for all tablets which contain this chip.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Postpone axis initialization to the first open instead of doing it
in joydev_connect. This is to make sure the generated startup events
are representative of the current joystick state rather than what
it was when joydev_connect() was called, potentially much earlier.
Once the first user is connected to joydev node we'll be updating
joydev->abs[] values and subsequent clients will be getting correct
initial states as well.
This solves issues with joystick driven menus that start scrolling
up each time they are started, until the user moves the joystick to
generate events. In emulator menu setups where the menu program is
restarted every time the game exits, the repeated need to move the
joystick to stop the unintended scrolling gets old rather quickly...
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On the latest series of ThinkPads, the button events for the TrackPoint
are reported through the touchpad itself as opposed to the TrackPoint
device. In order to report these buttons properly, we need to forward
them to the TrackPoint device and notify psmouse to send the button
presses/releases.
Signed-off-by: Lyude Paul <thatslyude@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch does several cleanup changes to F30 code
- switch to using BIT() macro
- use DIV_ROUND_UP() where appropriate
- factor out code setting up and reporting buttons
- use single loop when reporting buttons: arithmetic is cheap compared to
conditionals and associated branch misprediction.
Tested-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using custom method of "passing" extended buttons from the
touchpad to trackstick, let's switch to the newly introduced SERIO_OOB_DATA
channel.
Tested-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The tracksticks on the Lenovo thinkpads have their buttons connected
through the touchpad device. We already fixed that in synaptics.c, but
when we switch the device into RMI4 mode to have proper support, the
pass-through functionality can't deal with them easily.
We add a new PS/2 flag and protocol designed for psmouse. The RMI4 F03
pass-through can then emit a special set of commands to notify psmouse the
state of the buttons.
This patch implements the protocol in psmouse, while an other will
do the same for rmi4-f03.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some newer boards using mkbp we're hooking up non-matrix buttons and
switches to the EC but NOT to the main application processor.
Let's add kernel support to handle this. Rather than creating a whole
new input driver, we'll continue to use cros_ec_keyb and just report the
new keys.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With CONFIG_SERIO=m, we get a build error for the rmi4-f03 driver,
added in linux-4.10:
warning: (HID_RMI) selects RMI4_F03 which has unmet direct dependencies (!UML && INPUT && RMI4_CORE && (SERIO=y || RMI4_CORE=SERIO))
drivers/input/built-in.o: In function `rmi_f03_attention':
rmi_f03.c:(.text+0xcfe0): undefined reference to `serio_interrupt'
rmi_f03.c:(.text+0xd055): undefined reference to `serio_interrupt'
drivers/input/built-in.o: In function `rmi_f03_remove':
rmi_f03.c:(.text+0xd115): undefined reference to `serio_unregister_port'
drivers/input/built-in.o: In function `rmi_f03_probe':
rmi_f03.c:(.text+0xd209): undefined reference to `__serio_register_port'
An earlier patch tried to fix this, but missed the HID_RMI driver that
does a 'select' on the F03 backend.
This adds a hidden Kconfig symbol that enforces 'serio' to be enabled
when RMI4-F03 is, which covers all cases.
Fixes: d7ddad0acc ("Input: synaptics-rmi4 - fix F03 build error when serio is module")
Fixes: c5e8848fc9 ("Input: synaptics-rmi4 - add support for F03")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix to return error code -ENOMEM from the devm_kzalloc() error handling
case instead of 0, as done elsewhere in this function.
Fixes: 6bd0dcfacf ("Input: synaptics-rmi4 - factor out functions
from probe")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Set the LED_CORE_SUSPENDRESUME flag on our LED device so the
LED state will be automatically restored by LED core on resume.
Since Xbox One pads stop flashing only when reinitialized, we'll
send them the initialization packet so they calm down too.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function needs to communicate with an other, it's better to have
a way to retrieve this other.
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Xbox One S requires an ack to its mode button report, otherwise it
continuously retransmits the report. This makes the mode button appear to
be stuck down after it is pressed for the first time.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have a nice macro ensuring that the value is within certain range, let's
use it instead of open-coding.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If device is supposed to send absolute events (i.e. EV_ABS bit is set in
dev->evbit) but dev->absinfo is not allocated, then the driver has done
something wrong, and we should not register such device. Otherwise we'll
crash later, when driver tries to send absolute event.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If user tries to initialize uinput device mixing old and new style
initialization (i.e. using old UI_SET_ABSBIT instead of UI_ABS_SETUP,
we forget to allocate input->absinfo and will crash when trying to send
absolute events:
ioctl(ui, UI_DEV_SETUP, &us);
ioctl(ui, UI_SET_PHYS, "Test");
ioctl(ui, UI_SET_EVBIT, EV_ABS);
ioctl(ui, UI_SET_ABSBIT, ABS_X);
ioctl(ui, UI_SET_ABSBIT, ABS_Y);
ioctl(ui, UI_DEV_CREATE, 0);
Reported-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=191811
Fixes: fbae10db09 ("Input: uinput - rework ABS validation")
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These attributes provide various bits of information which may be enumerated
under the RMI4 protocol to user space.
This may be useful for displaying the particular version which is in use, or
selecting the correct firmware to flash.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The attribute returns the percentage complete. If the firmware update fails, it
reports a negative error code.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Evdev interface has been available for many years and by now everyone
is switched to using it, so let's stop offering /dev/input/mouseN
and /dev/psaux by default.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's drop legacy platform data support (there are no users in mainline)
and switch to using generic device properties, which will make the driver
simpler (non-OF boards can use property sets to describe hardware).
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of being OF-specific, let's switch to using generic device
properties, which will make this code usable on ACPI, device tree and
legacy boards that use property sets.
As part of the change let's rename matrix_keypad_parse_of_params() to
matrix_keypad_parse_properties().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These tests are reversed. A warning should be displayed if an error is
returned, not on success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MPU3050 driver in the input subsystem has been superseded by a proper
IIO driver found in drivers/iio/gyro/mpu3050*.
Patches have been submitted to remove all defconfig and related references
to the old driver and replace this input driver with the IIO driver.
So delete the input driver. Input was never a good fit for sensors anyway.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.
Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.
Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Declare device_type structures as const as they are only stored in the
type field of a device structure. This field is of type const, so add
const to declaration of device_type structures.
File size before:
text data bss dec hex filename
17184 1344 80 18608 48b0 drivers/input/input.o
File size after:
text data bss dec hex filename
17248 1280 80 18608 48b0 drivers/input/input.o
File size before:
text data bss dec hex filename
2355 384 8 2747 abb drivers/input/rmi4/rmi_bus.o
File size after:
text data bss dec hex filename
2483 264 8 2755 ac3 drivers/input/rmi4/rmi_bus.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYhRv9AAoJEHm+PkMAQRiG/uAH+wYT9qwvT460pUC6F1X5PNdN
H5KvaGsRNP1SjjQid5CrAFFDs52pFKf9GoV0Rn2WRoHAmEF1Dps4y/bMtR1GlsRB
IfOU+bnmH1Mmj4RCXUoFgFgYJVXC0WOz9SM5aCOAAZLCRF9BdkTpRo8lijuh141k
7YMqpaRhr/rJvQRZMEX+Q8HhfyNHz53olrykYp+O4x5F/CUihFzH76pY28j0YihS
wd/DdxrWyFn35DcFGfDb3yK7J2a6pGtnFw3RP4gU8DsH/Ks0133cR/2lOAtGDECN
dAGbLHoTvj3L4Twz5aiH6WRkXUkfDLK9UhxD/82UgLLmP5XvG1RdKZUNQ60CL5g=
=2TBu
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rc5' into next
Sync up with mainline to bring up improvements in various subsystems.
Commit 6480af4915 ("power_supply: wm97xx_battery: use
power_supply_get_drvdata") made wm97xx platform data mandatory, although
it's still optional.
This patch fixes an oops during driver probe on one of my MIPS boards with
a wm9712.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If there is no call to dev_get_drvdata() or input_get_drvdata(),
the call to input_set_drvdata() is unnecessary and can be dropped.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This can happen in cases like bug #102951[1], so add a proper debug msg
as done in wait_read. Also, change wait_read debug message to differ from
wait_write.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=102951
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "atomic" API allows us to configure PWM period and duty cycle and
enable it in one call.
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds an optional regulator to the pwm-beeper device. This regulator
acts as an amplifier. The amplifier is only enabled while beeping in order
to reduce power consumption.
Tested on LEGO MINDSTORMS EV3, which has a speaker connected to PWM through
an amplifier.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This suppress printing an error message when pwm_get returns -EPROBE_DEFER.
Otherwise you get a bunch of noise in the kernel log.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Usually userspace sends SND_BELL and SND_TONE events, and by the time
pwm_beeper_suspend() runs userpsace is already frozen, but theoretically
in-kernel users may send these events too, and that may cause
pwm_beeper_event() scheduling another work after we canceled it.
Let's introduce a "suspended" flag and check it in pwm_beeper_event() to
avoid this race.
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use of managed resources (devm) simplifies error handling and tear down
of the driver.
Reviewed-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are no more users of pwm-beeper driver in mainline relying on
this legacy API, so let's remove it and simplify the driver code.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it conssistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Empty remove functions don't serve a useful purpose and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling device_init_wakeup in the remove function is unnecessary since the
device is going away, and thus won't be able to cause any wakeups under any
circumstances. Besides, the driver cleanup code already handles the
necessary cleanup.
Similarly, disabling wakeup in the probe error path is unnecessary, as is
disabling wakeup in the probe function in the first place.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling device_init_wakeup in the remove function is unnecessary since the
device is going away, and thus won't be able to cause any wakeups under any
circumstances. Besides, the driver cleanup code already handles the
necessary cleanup.
Similarly, disabling wakeup in the probe error path is unnecessary, as is
disabling wakeup in the probe function in the first place.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling device_init_wakeup in the remove function is unnecessary since the
device is going away, and thus won't be able to cause any wakeups under any
circumstances. Besides, the driver cleanup code already handles the
necessary cleanup.
Similarly, disabling wakeup in the probe error path is unnecessary, as is
disabling wakeup in the probe function in the first place.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calling device_init_wakeup in the remove function is unnecessary since the
device is going away, and thus won't be able to cause any wakeups under any
circumstances. Besides, the driver cleanup code already handles the
necessary cleanup.
Similarly, disabling wakeup in the probe error path is unnecessary, as is
disabling wakeup in the probe function in the first place.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata(), platform_get_drvdata(),
or dev_get_drvdata() in any of the drivers in this patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata(), platform_get_drvdata(),
or dev_get_drvdata() in any of the drivers in this patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata(), platform_get_drvdata(),
or dev_get_drvdata() in any of the drivers in this patch.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gpio-keys input devices created by the soc_button_array driver are
configured with key-codes based on ACPI provided information.
Unfortunately on some tablets this info is wrong, and we need to have
a quirk to fix things up.
Add support for input_setkeycode to the gpio-keys driver, so that
the existing udev hwdb mechanism can be used to fix things up on these
tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The soc_button_array driver was initializing (kzalloc) the
debounce_interval value to 0, leading to no debouncing at all,
while the buttons are simple mechanical switches.
This commit sets debounce_interval to 50ms to avoid spurious button
press reports both on press and release of the button. Note 50ms may
seem like a lot but soc_button_array is typically used with cheap
tablets, with not so great buttons. I tried 10ms on my tablet and it
is not enough, where as 50ms works well.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for the TM2 touch key and led functionality.
The driver interfaces with userspace through an input device and reports
KEY_PHONE and KEY_BACK event types. LED brightness can be controlled by
"/sys/class/leds/tm2-touchkey/brightness".
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata() or dev_get_drvdata().
Drop the unnecessary call to i2c_set_clientdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Also use existing variable 'dev' instead of dereferencing it several times.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use local variable 'dev' instead of dereferencing it several times.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata() or dev_get_drvdata().
Drop the unnecessary call to i2c_set_clientdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to platform_set_drvdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use local variable 'dev' instead of dereferencing it several times and
replace devm_add_action() and manual error handling with
devm_add_action_or_reset().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Error messages after memory allocation failures are unnecessary and
can be dropped, especially give that they were emitted as dev_dbg() so
noone except person actively debugging the driver would see them.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to i2c_get_clientdata() or dev_get_drvdata().
Drop the unnecessary call to i2c_set_clientdata().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use local variable 'dev' instead of dereferencing it several times.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Error messages after memory allocation failures are unnecessary and
can be dropped, given that they are emitted as dev_dbg() so nobody except
person actively debugging the driver would see them.
Also replace jump to return 'goto l; ... l: return e;' with 'return e;'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no call to platform_get_drvdata() or dev_get_drvdata().
Drop the unnecessary call to dev_set_drvdata().
Other relevant changes:
Use existing variable 'dev' instead of dereferencing it several times
This conversion was done automatically with coccinelle using the
following semantic patches. The semantic patches and the scripts
used to generate this commit log are available at
https://github.com/groeck/coccinelle-patches
- Drop dev_set_drvdata()
- Use local variable 'struct device *dev' consistently
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The TCA8418 might be used using different interrupt triggers on various
boards. This is not working so far because the current code forces a
falling edge trigger.
The device tree already provides a trigger type, so let's use whatever it
sets up, and since we can be loaded without DT, keep the old behaviour for
the non-DT case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The clip values need the same swapping as the maximum values if the
sensor axes are swapped.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 50ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using counter based retry loops for peripherals results in the delay
being significantly overrun during high-load situations where delay
functions tend to be vary imprecise and overrun there timeouts. So
condition the termination on the actual condition of 2s for the
re-calibration to have been successful.
As this is a very long delay there is no advantage in using
high-resolution timers thus switching this to msleep().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver currently only supports legacy platform data probe. This
change adds device tree support and gets rid of platform data probe code
since no one is actually using mpr121 platform data in the mainline.
The device tree property parsing code is based on the work of
atmel_captouch driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver reports input events on their interrupts which are triggered
by the sensor's status register changes. But only single bit change is
reported in the interrupt handler. So if there are multiple bits are
changed at almost the same time, other press or release events are ignored.
This fixes it by detecting all changed bits in the status register.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver reports misc scan input events on the sensor's status
register changes. But the event capability for them was not set in the
device initialization, so these events were ignored.
This change adds the missing event capability.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove unused key_val field in struct mpr121_touchkey.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using #ifdef, let's mark suspend and resume methods as
__maybe_unused to provide better compile coverage.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Small driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elants_i2c - avoid divide by 0 errors on bad touchscreen data
Input: adxl34x - make it enumerable in ACPI environment
Input: ALPS - fix TrackStick Y axis handling for SS5 hardware
Input: synaptics-rmi4 - fix F03 build error when serio is module
Input: xpad - use correct product id for x360w controllers
Input: synaptics_i2c - change msleep to usleep_range for small msecs
Input: i8042 - add Pegatron touchpad to noloop table
Input: joydev - remove unused linux/miscdevice.h include
The Moorestown support was removed by commit 1a8359e411 ("x86/mid: Remove
Intel Moorestown").
Remove this leftover.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep(1~20) may not do what the caller intends, and will often sleep
longer (~20 ms actual sleep for any value given in the 1~20ms range). This
is not the desired behaviour for many cases like device resume time, device
suspend time, device enable time, retry logic, etc. Thus, change msleep to
usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked-by: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The order of endpoints is well defined on official Xbox pads, but
we have found at least one 3rd-party pad that doesn't follow the
standard ("Titanfall 2 Xbox One controller" 0e6f:0165).
Fortunately, we get lucky with this specific pad because it uses
endpoint addresses that differ only by direction. We know that
there are other pads out where this is not true, so let's go
ahead and fix this.
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace first goto with simple returns as we really are just returning
one error code.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
xbox one was the only device that has a *_process_buttons routine.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ACPI-enabled platform may contain _DSD method to enable this driver
using compatible string.
Remove OF specifics to re-use existing code on ACPI-enabled platforms.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A minus character was lost in commit 23fce365, causing the Y axis to be
inverted for SS5 TrackStick events. (Pushing the TrackStick up caused
the pointer to move down, and vice versa.) Restore the lost minus.
Fixes: 23fce365c6 ("Input: ALPS - clean up code for SS5 hardware")
Signed-off-by: Paul Donohue <linux-kernel@PaulSD.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rmi_dev is currently being dereferenced before it null checked, however,
after deeper inspecting, rmi_dev can never be null, so just remove this
redundant check.
Fixes CoverityScan CID 1391218 ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
version is a u8, the check for version > 0 means that version can only
be zero, so the subsequent check for version != 0 is never true and
hence is redudant code and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need to repeat "depends on RMI4_CORE" on every bit of RMI4
support, we can guard all of them at once with "if RMI4_CORE".
Also use tabs for F03 indentation.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep (1~20) may not do what the caller intends, and will often sleep
longer. (~20 ms actual sleep for any value given in the 1~20ms range) This
is not the desired behaviour for many cases like device resume time, device
suspend time, device enable time, etc. Thus, change msleep to usleep_range
for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked by: Albert Zhang <xu.zhang@bosch-sensortec.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since F03 is a boolean, "depends" on symbols that can be modules
do not work quite right. We can enable F03 if SERIO is built-in or
if both RMI core and SERIO core are modules. If SERIO core is module,
but RMI is built-in, we'll get:
drivers/built-in.o: In function `rmi_f03_attention':
rmi_f03.c:(.text+0xf8ef8): undefined reference to `serio_interrupt'
rmi_f03.c:(.text+0xf8fbd): undefined reference to `serio_interrupt'
drivers/built-in.o: In function `rmi_f03_remove':
rmi_f03.c:(.text+0xf9082): undefined reference to `serio_unregister_port'
drivers/built-in.o: In function `rmi_f03_probe':
rmi_f03.c:(.text+0xf9260): undefined reference to `__serio_register_port'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
currently the controllers get the same product id as the wireless
receiver. However the controllers actually have their own product id.
The patch makes the driver expose the same product id as the windows
driver.
This improves compatibility when running applications with WINE.
see https://github.com/paroj/xpad/issues/54
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Ingo Molnar:
"There's a number of fixes:
- a round of fixes for CPUID-less legacy CPUs
- a number of microcode loader fixes
- i8042 detection robustization fixes
- stack dump/unwinder fixes
- x86 SoC platform driver fixes
- a GCC 7 warning fix
- virtualization related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
Revert "x86/unwind: Detect bad stack return address"
x86/paravirt: Mark unused patch_default label
x86/microcode/AMD: Reload proper initrd start address
x86/platform/intel/quark: Add printf attribute to imr_self_test_result()
x86/platform/intel-mid: Switch MPU3050 driver to IIO
x86/alternatives: Do not use sync_core() to serialize I$
x86/topology: Document cpu_llc_id
x86/hyperv: Handle unknown NMIs on one CPU when unknown_nmi_panic
x86/asm: Rewrite sync_core() to use IRET-to-self
x86/microcode/intel: Replace sync_core() with native_cpuid()
Revert "x86/boot: Fail the boot if !M486 and CPUID is missing"
x86/asm/32: Make sync_core() handle missing CPUID on all 32-bit kernels
x86/cpu: Probe CPUID leaf 6 even when cpuid_level == 6
x86/tools: Fix gcc-7 warning in relocs.c
x86/unwind: Dump stack data on warnings
x86/unwind: Adjust last frame check for aligned function stacks
x86/init: Fix a couple of comment typos
x86/init: Remove i8042_detect() from platform ops
Input: i8042 - Trust firmware a bit more when probing on X86
x86/init: Add i8042 state to the platform data
...
The error message "Can't read CTR while initializing i8042" appears on
Cherry Trail-based devices at each boot time:
i8042: PNP: No PS/2 controller found. Probing ports directly.
i8042: Can't read CTR while initializing i8042
i8042: probe of i8042 failed with error -5
This happens because we historically do not trust firmware on X86 and,
while noting that PNP does not show keyboard or mouse devices, we still
charge ahead and try to probe the controller. Let's relax this a bit and if
results of PNP probe agree with the results of platform
initialization/quirks conclude that there is, in fact, no i8042.
While at it, let's avoid using x86_platform.i8042_detect() and instead
abort execution early if platform indicates that it can not possibly have
i8042 (x86_platform.legacy.i8042 equals X86_LEGACY_I8042_PLATFORM_ABSENT).
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/1481317061-31486-3-git-send-email-dmitry.torokhov@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We rely on the result of scanning PNP bus for keyboard and mouse devices to
decide whether we should continue initialization of i8042 driver or not, so
the probes can not be asynchronous.
Also, it is not a good idea to unbind either of the PNP devices while i8042
is running, so let's disable bind/unbind for the PNP drivers through sysfs
and rely on i8042 cleaning after itself properly. User can still unbind and
rebind entire i8042 and that will take care of PNP drivers as well.
Reviewed-by: Luis R. Rodriguez <mgrof@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, retry logic, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Avoid AUX loopback in Pegatron C15B touchpad, so input subsystem is able
to recognize a Synaptics touchpad in the AUX port.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=93791
(Touchpad is not detected on DNS 0801480 notebook (PEGATRON C15B))
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch remove the inclusion of linux/miscdevice.h for joydev
since it does not use miscdevice.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
- updated support for Synaptics RMI4 devices, including support for
SMBus controllers, firmware update support, sensor tuning, and PS/2
guest support
- ALPS driver now supports tracksticks on SS5 controllers
- i8042 now uses chassis info to skip selftest on Asus laptops as list
of individual models became too unwieldy
- miscellaneous fixes to other drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (67 commits)
Input: imx6ul_tsc - generalize the averaging property
Input: drv260x - use generic device properties
Input: drv260x - use temporary for &client->dev
Input: drv260x - fix input device's parent assignment
Input: synaptics-rmi4 - add support for F34 V7 bootloader
Input: drv260x - fix initializing overdrive voltage
Input: ALPS - fix protcol -> protocol
Input: i8042 - comment #else/#endif of CONFIG_PNP
Input: lpc32xx-keys - fix invalid error handling of a requested irq
Input: synaptics-rmi4 - fix debug for sensor clip
Input: synaptics-rmi4 - store the attn data in the driver
Input: synaptics-rmi4 - allow to add attention data
Input: synaptics-rmi4 - f03 - grab data passed by transport device
Input: synaptics-rmi4 - add support for F03
Input: imx6ul_tsc - convert int to u32
Input: imx6ul_tsc - add mask when set REG_ADC_CFG
Input: synaptics-rmi4 - have only one struct platform data
Input: synaptics-rmi4 - remove EXPORT_SYMBOL_GPL for internal functions
Input: synaptics-rmi4 - remove mutex calls while updating the firmware
Input: drv2667 - fix misuse of regmap_update_bits
...
Make the avarage-samples property a general touchscreen property
rather than imx6ul device specific.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- Support for stereo DAPM controls
- Some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- A new version of the topology ABI; this should be backward compatible
- Updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- New drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- Yet another race fix at disconnection
- Tolerated packet size calculation for some Android devices
- Quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- Improvement of Dell pin fixup mapping
- Quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- Replace all kthread usages with simple works
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=WZeb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No dramatic changes are found in this development cycle, but as usual,
many commits are applied in a wide range of drivers.
Most of big changes are in ASoC, where a few bits of framework work
and quite a lot of cleanups and improvements to existing code have
been done. The rest are usual stuff, a few HD-audio and USB-audio
quirks and fixes, as well as the drop of kthread usages in the whole
subsystem.
Below are some highlights:
ASoC:
- support for stereo DAPM controls
- some initial work on the of-graph sound card
- regmap conversions of the remaining AC'97 drivers
- a new version of the topology ABI; this should be backward
compatible
- updates / cleanups of rsnd, sunxi, sti, nau8825, samsung, arizona,
Intel skylake, atom-sst
- new drivers for Cirrus Logic CS42L42, Qualcomm MSM8916-WCD, and
Realtek RT5665
USB-audio:
- yet another race fix at disconnection
- tolerated packet size calculation for some Android devices
- quirks for Axe-Fx II, QuickCam, TEAC 501/503
HD-audio:
- improvement of Dell pin fixup mapping
- quirks for HP Z1 Gen3, Alienware 15 R2 2016 and ALC622 headset mic
Misc:
- replace all kthread usages with simple works"
* tag 'sound-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (296 commits)
ALSA: hiface: Fix M2Tech hiFace driver sampling rate change
ALSA: usb-audio: Eliminate noise at the start of DSD playback.
ALSA: usb-audio: Add native DSD support for TEAC 501/503 DAC
ASoC: wm_adsp: wm_adsp_buf_alloc should use kfree in error path
ASoC: topology: avoid uninitialized kcontrol_type
ALSA: usb-audio: Add QuickCam Communicate Deluxe/S7500 to volume_control_quirks
ALSA: usb-audio: add implicit fb quirk for Axe-Fx II
ASoC: zte: spdif: correct ZX_SPDIF_CLK_RAT define
ASoC: zte: spdif and i2s drivers are not zx296702 specific
ASoC: rsnd: setup BRGCKR/BRRA/BRRB when starting
ASoC: rsnd: enable/disable ADG when suspend/resume timing
ASoC: rsnd: tidyup ssi->usrcnt counter check in hw_params
ALSA: cs46xx: add a new line
ASoC: Intel: update bxt_da7219_max98357a to support quad ch dmic capture
ASoC: nau8825: disable sinc filter for high THD of ADC
ALSA: usb-audio: more tolerant packetsize
ALSA: usb-audio: avoid setting of sample rate multiple times on bus
ASoC: cs35l34: Simplify the logic to set CS35L34_MCLK_CTL setting
ALSA: hda - Gate the mic jack on HP Z1 Gen3 AiO
ALSA: hda: when comparing pin configurations, ignore assoc in addition to seq
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJYT5HMAAoJELDendYovxMvhNQH/1g/3ahM4JKN8Z0SbjKBEdQm
yj2xOj6cE3l6wMSUblKjZD2DLLhpmcHT/E97Xro/lZQEfQJoMXXWWDFowMU/P1LA
mJxb7Fzq5Wr+6eGSAlIQB270MrpNi/luf+CWHMwVA3V7R3KRXwonOdGQSkISIzCd
tgIydEA3a9r2+HgeIBpZFZ4GcSrJQU75krMyl2tjD1C+jeYVd+zdoj2OnDsZQDZQ
hDWApMpNbpSBAn7JtSSdXWSTBsGH0lUECebeYPhPQ2sX2P6Y8+UCGwA7i6FFdbTa
agXfVSdRz8dCe3k19VcKDAw6nK9BTTMnEeEHmkmygIh6wuHPP44CzigTXIbJoXI=
=zjfm
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for 4.10
These are some fixes, a move of some arm related headers to share them
between arm and arm64 and a series introducing a helper to make code
more readable.
The most notable change is David stepping down as maintainer of the
Xen hypervisor interface. This results in me sending you the pull
requests for Xen related code from now on"
* tag 'for-linus-4.10-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (29 commits)
xen/balloon: Only mark a page as managed when it is released
xenbus: fix deadlock on writes to /proc/xen/xenbus
xen/scsifront: don't request a slot on the ring until request is ready
xen/x86: Increase xen_e820_map to E820_X_MAX possible entries
x86: Make E820_X_MAX unconditionally larger than E820MAX
xen/pci: Bubble up error and fix description.
xen: xenbus: set error code on failure
xen: set error code on failures
arm/xen: Use alloc_percpu rather than __alloc_percpu
arm/arm64: xen: Move shared architecture headers to include/xen/arm
xen/events: use xen_vcpu_id mapping for EVTCHNOP_status
xen/gntdev: Use VM_MIXEDMAP instead of VM_IO to avoid NUMA balancing
xen-scsifront: Add a missing call to kfree
MAINTAINERS: update XEN HYPERVISOR INTERFACE
xenfs: Use proc_create_mount_point() to create /proc/xen
xen-platform: use builtin_pci_driver
xen-netback: fix error handling output
xen: make use of xenbus_read_unsigned() in xenbus
xen: make use of xenbus_read_unsigned() in xen-pciback
xen: make use of xenbus_read_unsigned() in xen-fbfront
...
Update driver drv260x to use generic device properties so that it can be
used on non-DT systems. We also remove platform data as generic device
properties work on static board code as well.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's introduce a temporary for "client->dev" is probe() as we use
it quite a few times and "dev" is shorter.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We were assigning I2C bus controller instead of client as parent device.
Besides being logically wrong, it messed up with devm handling of input
device. As a result we were leaving input device and event node behind
after rmmod-ing the driver, which lead to a kernel oops if one were to
access the event node later.
Let's remove the assignment and rely on devm_input_allocate_device() to
set it up properly for us.
Signed-off-by: Jingkui Wang <jkwang@google.com>
Fixes: 7132fe4f56 ("Input: drv260x - add TI drv260x haptics driver")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Port firmware update code from Samsung Galaxy S7 driver into
mainline framework.
This patch has been tested on Synaptics S7813.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We were accidentally initializing haptics->rated_voltage twice, and did not
initialize overdrive voltage.
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As this define check if huge, this makes easier to read the code.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Semantics of NR_IRQS is different on machines with SPARSE_IRQ option
disabled or enabled, in the latter case IRQs are allocated starting
at least from the value specified by NR_IRQS and going upwards, so
the check of (irq >= NR_IRQ) to decide about an error code returned by
platform_get_irq() is completely invalid, don't attempt to overrule
irq subsystem in the driver.
The change fixes lpc32xx_keys driver initialization on boot:
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The debug would only ever output zero for the clip information.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that we have a proper API to set the attention data, there is
no point in keeping it in the transport driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The HID implementation of RMI4 provides the data during
the interrupt (in the input report). We need to provide
a way for this transport driver to provide the attention
data while calling an IRQ.
We use a fifo in rmi_core to not lose any incoming event.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
First check if there are data available passed by the transport device.
If data available use these data. If there are no data available
try to read the rmi block if dsata are passed this way.
This is the way the other rmi function handlers will do this.
This patch is needed on HID devices because the firmware reads F03 data
registers and adds them to the HID attention report. Reading those
registers from the driver after the firmware read them will result in
invalid data.
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds basic functionality for PS/2 passthrough on Synaptics
Touchpads using RMI4 through smbus.
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Lyude Paul <thatslyude@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The name of a codec pin can have an optional prefix string, which is
defined by the SoC machine driver. The snd_soc_dapm_x_pin functions
take the fully-specified name including the prefix and so the existing
code would fail to find the pin if the audio machine driver had added
a prefix.
Switch to using the snd_soc_component_x_pin equivalent functions that
take a specified SoC component and automatically add the name prefix to
the provided pin name.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull input fixes from Dmitry Torokhov: "We are disabling automatic
probing of BYD touchpads as it results in too many false positives,
and the hardware is not terribly popular and having the protocol
support does not result in significantly improved user experience.
We also change keycode for KEY_DATA to avoid clashing with
KEY_FASTREVERSE. Luckily this newish code is used by CEC framework
that is still in staging, so it is extremely unlikely that someone has
already started using this keycode"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: change KEY_DATA from 0x275 to 0x277
Input: psmouse - disable automatic probing of BYD touchpads
Wolfram Sang