Bspec says:
"Restriction : SRD must not be enabled when the PSR Setup time from DPCD
00071h is greater than the time for vertical blank minus one line."
Let's check for that and disallow PSR if we exceed the limit.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview
While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.
Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.
Changes since v1:
- Add comment explaining the addition of the if
(!mode_config->poll_running) in intel_hpd_init()
- Remove unneeded if (!dev->mode_config.poll_enabled) in
i915_hpd_poll_init_work()
- Call to drm_helper_hpd_irq_event() after we disable polling
- Add cancel_work_sync() call to intel_hpd_cancel_work()
Changes since v2:
- Apparently dev->mode_config.poll_running doesn't actually reflect
whether or not a poll is currently in progress, and is actually used
for dynamic module paramter enabling/disabling. So now we instead
keep track of our own poll_running variable in dev_priv->hotplug
- Clean i915_hpd_poll_init_work() a little bit
Changes since v3:
- Remove the now-redundant connector loop in intel_hpd_init(), just
rely on intel_hpd_poll_enable() for setting connector->polled
correctly on each connector
- Get rid of poll_running
- Don't assign enabled in i915_hpd_poll_init_work before we actually
lock dev->mode_config.mutex
- Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
for doc purposes
- Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
intel_hpd_poll_enable()
- Add some comments about racing not mattering in intel_hpd_poll_enable
Changes since v4:
- Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
- Drop the bool argument from intel_hpd_poll_init()
- Remove redundant calls to intel_hpd_poll_init()
- Rename poll_enable_work to poll_init_work
- Add some kerneldoc for intel_hpd_poll_init()
- Cross-reference intel_hpd_poll_init() in intel_hpd_init()
- Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()
Changes since v5:
- Minor kerneldoc nitpicks
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 19625e85c6)
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a89247)
has_dsi_encoder was introduced to indicate that the pipe is driving
a DSI encoder. Now that we have the output_types bitmask that can
tell us the same thing, let's just kill has_dsi_encoder.
v2: Rebase, handle BXT DSI transcoder, rewrote commit message
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-10-git-send-email-ville.syrjala@linux.intel.com
INTEL_OUTPUT_DISPLAYPORT hsa been bugging me for a long time. It always
looks out of place besides INTEL_OUTPUT_EDP and INTEL_OUTPUT_DP_MST.
Let's just rename it to INTEL_OUTPUT_DP.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-9-git-send-email-ville.syrjala@linux.intel.com
With the introduction of the output_types mask, intel_pipe_has_type()
and intel_pipe_will_have_type() are basically the same thing. Replace
them with a new intel_crtc_has_type() (identical to
intel_pipe_will_have_type() actually).
v2: Rebase
v3: Make intel_crtc_has_type() static inline (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-5-git-send-email-ville.syrjala@linux.intel.com
Rather than looping through encoders to see which encoder types
are being driven by the pipe, add an output_types bitmask into
the crtc state and populate it prior to compute_config and during
state readout.
v2: Determine output_types before .compute_config() hooks are called
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-4-git-send-email-ville.syrjala@linux.intel.com
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
usleep_range is not recommended for waits shorten than 10us.
Make the wait_for_us use the atomic variant for such waits.
To do so we need to reimplement the _wait_for_atomic macro to
be safe with regards to preemption and interrupts.
v2: Reimplement _wait_for_atomic to be irq and preemption safe.
(Chris Wilson and Imre Deak)
v3: Fixed in_atomic check due rebase error.
v4: Build bug on non-constant timeouts.
v5: Compile away cpu migration code in atomic paths.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1467114710-29989-1-git-send-email-tvrtko.ursulin@linux.intel.com
Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk
Currently setting up the backlight for a panel is sometimes done
together with initialising the panel, and sometimes after the connector
is registered. The backlight setup does not depend upon connector
registration (i.e. access to sysfs/debugfs and the kobject hierachy) so
perform it consistently just after panel initialisation.
Note the discrepancy here as destroying the panel is done during
connector unregistration...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-1-git-send-email-chris@chris-wilson.co.uk
Backmerge drm-next for the reworked device register/unregistering.
Chris Wilson needs that to be able to land his i915 load/unload
demidlayering.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
- Infrastructure for GVT-g (paravirtualized gpu on gen8+), from Zhi Wang
- another attemp at nonblocking atomic plane updates
- bugfixes and refactoring for GuC doorbell code (Dave Gordon)
- GuC command submission enabled by default, if fw available (Dave Gordon)
- more bxt w/a (Arun Siluvery)
- bxt phy improvements (Imre Deak)
- prep work for stolen objects support (Ankitprasa Sharma & Chris Wilson)
- skl/bkl w/a update from Mika Kuoppala
- bunch of small improvements and fixes all over, as usual
* tag 'drm-intel-next-2016-06-20' of git://anongit.freedesktop.org/drm-intel: (81 commits)
drm/i915: Update DRIVER_DATE to 20160620
drm/i915: Introduce GVT context creation API
drm/i915: Support LRC context single submission
drm/i915: Introduce execlist context status change notification
drm/i915: Make addressing mode bits in context descriptor configurable
drm/i915: Make ring buffer size of a LRC context configurable
drm/i915: gvt: Introduce the basic architecture of GVT-g
drm/i915: Fold vGPU active check into inner functions
drm/i915: Use offsetof() to calculate the offset of members in PVINFO page
drm/i915: Factor out i915_pvinfo.h
drm/i915: Serialise presentation with imported dmabufs
drm/i915: Use atomic commits for legacy page_flips
drm/i915: Move fb_bits updating later in atomic_commit
drm/i915: nonblocking commit
Reapply "drm/i915: Pass atomic states to fbc update, functions."
drm/i915: Roll out the helper nonblock tracking
drm/i915: Signal drm events for atomic
drm/i915/ilk: Don't disable SSC source if it's in use
drm/i915/guc: (re)initialise doorbell h/w when enabling GuC submission
drm/i915/guc: replace assign_doorbell() with select_doorbell_register()
...
The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.
This also paves the way towards using the actual port->PPS instance
mapping based on VBT.
This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96436
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-2-git-send-email-imre.deak@intel.com
Atm on IBX/CPT we attempt to detect if eDP is present even if LVDS was
already detected and an encoder for it was registered. This involves
trying to read out the eDP DPCD, which in turn needs the same power
sequencer that LVDS uses. Poking at the VDD line at an unexpected time
may or may not interfere with the LVDS panel, but it's probably safer to
prevent this. Registering both an LVDS and an eDP connector would also
present a similar problem accessing the shared PPS at any point later in
an unexpected way.
We also need this to be able fix PPS initialization before its first use
in the next patch. For that we want to be sure that PPS is not in use
by LVDS.
v2:
- Split out the PPS init fix to a separate patch. (Chris)
- Add comment about eDP init depending on LVDS init. (Chris)
- Make the use of the intel_encoder ptr less error prone.
v3:
- Use IBX/CPT reference instead of the incorrect ILK, add a WARN about
this. (Ville)
v4:
- Use a helper to get the lvds encoder instead of opencoding the same.
(Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-2-git-send-email-imre.deak@intel.com
During cleanup we have to synchronise with the async task we are using
to initialise and register our fbdev. Currently, we are using a full
synchronisation on the global domain, but we can restrict this to just
synchronising up to our task if we remember our cookie.
Whilst there, streamline the function parameters.
v2: async_synchronize_cookie() takes an exclusive upper bound, to
synchronize with our task we have to pass in the next cookie.
v3: Drop premature disregarding of the active cookie (we need to wait
until the task is complete before continuing in the teardown).
v4: Refactor waiting on async to incorporate a comment explaining why we
need the +1.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466497015-8509-2-git-send-email-chris@chris-wilson.co.uk
It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.
This is a manual revert of commits 5fa836a9d8 ("drm/i915: DP link
training optimization") and 4e96c97742 ("drm/i915: eDP link training
optimization").
Fixes: 5fa836a9d8 ("drm/i915: DP link training optimization")
Fixes: 4e96c97742 ("drm/i915: eDP link training optimization")
Cc: <stable@vger.kernel.org> # v4.2+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
Currently the backlight is being unregistered in the unload phase (after
the display and its objects are unregistered). Move the backlight
unregistration into the analogous phase by performing it from the
connector unregistration, just prior to its deletion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466160034-12173-3-git-send-email-chris@chris-wilson.co.uk
We now have a connector->func that serves the same purpose as our own
intel_connector->unregister vfunc allowing us to unwrap ourselves and
use drm_connector_register() (and friends) as the central function.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466160034-12173-2-git-send-email-chris@chris-wilson.co.uk
Backmerge drm-next to get at the nonblocking atomic helpers, needed to
merge the i915 conversion.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Rename these remaining function prefixes to better align with the
corresponding SKL functions.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
So far we configured a static lane latency optimization during driver
loading/resuming. The specification changed at one point and now this
configuration depends on the lane count, so move the configuration
to modeset time accordingly.
It's not clear when this lane configuration takes effect. The
specification only requires that the programming is done before enabling
the port. On CHV OTOH the lanes start to power up already right after
enabling the PLL. To be safe preserve the current order and set things
up already before enabling the PLL.
v2: (Ander)
- Simplify the optimization mask calculation.
- Use the correct pipe_config always during the calculation instead
of the bogus intel_crtc->config.
CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95476
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
So far we depended on the HW to dynamically power down unused PHYs and
so we enabled them manually once during driver loading/resuming. There
are indications however that we can achieve better power savings by
manual powering toggling. So make the PHY enabling/disabling to happen
on-demand whenever we need either the corresponding AUX or port
functionality. CHV does this already by enabling the PHY along the
corresponding PHY common lane power wells there, do the same on BXT by
adding virtual power wells for the same purpose.
Also sanity check the common lane power down ack signal from the PHY. Do
this only when the PHY is enabled, since it's not clear at what point
the HW power/clock gates things.
While at it rename broxton_ prefix to bxt_ in related function names to
better align with the SKL code.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
For all outputs except dp_mst, we have a 1:1 relationship between
connectors and encoders and the driver is relying on the atomic helpers:
we can drop the custom ->best_encoder() implementation and let the core
call drm_atomic_helper_best_encoder() for us.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-7-git-send-email-boris.brezillon@free-electrons.com
If the VBT says that a certain port should be eDP (and hence fused off
from HDMI), but in reality it isn't, we need to try and acquire the HDMI
connection instead. So only trust the VBT edp setting if we can connect
to an eDP device on that port.
Fixes: d2182a6608 (drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV)
References: https://bugs.freedesktop.org/show_bug.cgi?id=96288
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Phidias Chiang <phidias.chiang@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464766070-31623-1-git-send-email-chris@chris-wilson.co.uk
This reverts the following patches:
d55dbd06bb drm/i915: Allow nonblocking update of pageflips.
15c86bdb76 drm/i915: Check for unpin correctness.
95c2ccdc82 Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b7304 drm/i915: Make unpin async.
03f476e1fc drm/i915: Prepare connectors for nonblocking checks.
2099deffef drm/i915: Pass atomic states to fbc update functions.
ee7171af72 drm/i915: Remove reset_counter from intel_crtc.
2ee004f7c5 drm/i915: Remove queue_flip pointer.
b8d2afae55 drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d922 drm/i915: Remove cs based page flip support.
143f73b3bf drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b64 drm/i915: Add the exclusive fence to plane_state.
6885843ae1 drm/i915: Convert flip_work to a list.
aa420ddd8e drm/i915: Allow mmio updates on all platforms, v2.
afee4d8707 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.
"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.
Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(
There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.
Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.
Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
the area) and not make sure domain experts had a chance to read it.
- Patches should be properly split up. I only looked at the two
patches that should be reverted in detail, but both look like the
mix up different things in one patch.
- Patches really should have proper commit messages. Especially when
doing more than one thing, and especially when touching critical and
tricky core code.
- Building a patch series and r-b stamping it when it has a built-in
bisect breakage is not a good idea.
- I also think we need to stop building up technical debt by
postponing atomic igt testcases even longer. I think it's clear that
there's enough corner cases in this beast that we really need to
have the testcases _before_ the next step lands.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Rather than having a BXT specific function to make sure the DE PLL is
enabled after disabling DC6, let's just make sure the current cdclk
is the same as what we last programmed.
Having another check in bxt_display_core_init() almost immediately after
the cdclk init seems redundant, so let's just kill that one.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-21-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Currently we initialize cdclk on SKL from two different places,
depending on whether it's during driver init or resume. Let's
unify it to happen from the same place always, and that place will be
the display core init function.
To do this we first run through the cdclk sanitation code, which will
first verify that the PLL is programmed correctly, after which we can
read out the current cdclk frequency, and once the cdclk is known we
verify that the cdclk "decimal" frequency is programmed correctly. If
any of these fail we will force a cdclk change, and to be safe we also
force the PLL to be turned off and on again. If the sanitation step
didn't notice anything amiss, we'll skip the cdclk programming which
will prevent cdclk reprogramming when the displays might be active.
We can also toss in a few WARNs about the register values into
skl_update_dpll0() since we now know that the PLL state should
always be sane when that function is called.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Now that skl_vco_freq tracks the actual DPLL0 vco frequency, we'll need
something that keeps track of which vco frequency we want to use in case
the current vco is 0. This would be important across supend/resume since
we'll disable DPLL0 around those parts.
We'll also update our idea of max cdclk/dotclock when the preferred
vco changes. That could happen if out initial guess was wrong, and
later eDP would force us to change it. One issue here could be that
changing the max dotclock could cause our mode list to change during
next time the displays get probed. But I don't see a good way to avoid
that, except perhaps by allowing either vco frequency to be used as
needed. But the docs suggest that such usage wasn't really inteded.
Also need to make sure we don't update our max_cdclk value before we
have a preferred vco value, which means moving that to happen after
the cdclk sanitation.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
WARNING: Using ChromeOS with an eDP panel and a 4K@60 DP monitor connected
to DDI1 the system will hard hang during a cold boot. Occurs when DDI1
is enabled when the cdclk is less then required. DP connected to DDI2
and HPD on either port works correctly.
Set cdclk based on the max required pixel clock based on VCO
selected. Track boot vco instead of boot cdclk.
The vco is now tracked at the atomic level and all CRTCs updated if
the required vco is changed. Not tested with eDP v1.4 panels that
require 8640 vco due to availability.
V1: initial version
V2: add vco tracking in intel_dp_compute_config(), rename
skl_boot_cdclk.
V3: rebase, V2 feedback not possible as encoders are not aware of
atomic.
V4: track target vco is atomic state. modeset all CRTCs if vco changes
V5: rename atomic variable, cleaner if/else logic, use existing vco if
encoder does not return a new vco value. check_patch.pl cleanup
V6: simplify logic in intel_modeset_checks.
V7: reorder an IF for readability and whitespace fix.
V8: use dev_cdclk for tracking new cdclk during atomic
V9: correctly handle vco 8640 when crtcs==0
V10: Clean up if else in crtcs==0
V11: Rebase for new intel_dpll_mgr.c
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
[vsyrjala: rebased due to churn]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-3-git-send-email-ville.syrjala@linux.intel.com
intel_unpin_work may not take the list lock because it requires the connector_mutex.
To prevent taking locks we add an array of old and new state. The old state to free,
the new state to commit and verify.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-18-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Create a work structure that will be used for all changes. This will
be used later on in the atomic commit function.
Changes since v1:
- Free old_crtc_state from unpin_work_fn properly.
Changes since v2:
- Add hunk for calling hw state verifier.
- Add missing support for color spaces.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-12-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
With intel_pipe_update begin/end we ensure that the mmio updates
don't run during vblank interrupt, using the hw counter we can
be sure that when current vblank count != vblank count at the time
of pipe_update_end the mmio update is complete.
This allows us to use mmio updates on all platforms, using the
update_plane call.
With Chris Wilson's patch to skip waiting for vblanks for
legacy_cursor_update this potentially leaves a small race
condition, in which update_plane can be called with a freed
crtc_state. Because of this commit acf4e84d61
("drm/i915: Avoid stalling on pending flips for legacy cursor updates")
is temporarily reverted.
Changes since v1:
- Split out the flip_work rename.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-9-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Rename intel_unpin_work to intel_flip_work and use it for mmio flips
and unpinning. Use flip_queued_req to hold the wait request in the
mmio case, and the vblank counter from intel_crtc_get_vblank_counter.
MMIO flips get their own path through intel_finish_page_flip_mmio,
handled on vblank. CS page flips go through *_cs.
Changes since v1:
- Clean up destinction between MMIO and CS flips.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-7-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Instead of calling prepare_flip right before calling finish_page_flip
do everything from prepare_page_flip in finish_page_flip.
Putting prepare and finish page_flip in a single step removes the need
for INTEL_FLIP_COMPLETE, so it can be removed. This simplifies the code
slightly.
Changes since v1:
- Invert if case to simplify code.
- Add missing barrier.
- Reword commit message.
Changes since v2:
- intel_page_flip_plane is removed.
- work->pending is turned into a bool.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-5-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Both intel_unpin_work.pending and intel_unpin_work.enable_stall_check
were used to see if work should be enabled. By only using pending
some special cases are gone, and access to unpin_work can be simplified.
A flip could previously be queued before
stallcheck was active. With the addition of the pending member
enable_stall_check became obsolete and can thus be removed.
Use this to only access work members untilintel_mark_page_flip_active
is called, or intel_queue_mmio_flip is used. This will prevent
use-after-free, and makes it easier to verify accesses.
Changes since v1:
- Reword commit message.
- Do not access unpin_work after intel_mark_page_flip_active.
- Add the right memory barriers.
Changes since v2:
- atomic_read() needs a full smp_rmb.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463490484-19540-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
If the source of the backlight PWM is from the
panel then the PWM can be controlled by DCS
command, this patch adds the support to
enable/disbale panel PWM, control backlight level
etc...
v2: Moving the CABC bkl functions to new file.(Jani)
v3: Rebase
v4: Rebase
v5: Use mipi_dsi_dcs_write() instead of mipi_dsi_dcs_write_buffer() (Jani)
Move DCS macro`s to include/video/mipi_display.h (Jani)
v6: Rename the file to intel_dsi_panel_pwm.c
Removing the CABC operations
v7 by Jani: renames, rebases, etc.
v8 by Jani: s/INTEL_BACKLIGHT_CABC/INTEL_BACKLIGHT_DSI_DCS/
v9 by Jani: rename init function to intel_dsi_dcs_init_backlight_funcs
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/71238a4b14b8c3a6c04070c789f09f1b4bc00a15.1461676337.git.jani.nikula@intel.com
Backmerge request by Jani to get at
commit 249c4f538b
Author: Deepak M <m.deepak@intel.com>
Date: Wed Mar 30 17:03:39 2016 +0300
drm: Add new DCS commands in the enum list
Some simple conflicts in intel_dp.c.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We calculate the watermark config into intel_atomic_state and then save
it into dev_priv, but never actually use it from there. This is
left-over from some early ILK-style watermark programming designs that
got changed over time.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-18-git-send-email-matthew.d.roper@intel.com
Moving watermark calculation into the check phase will allow us to to
reject display configurations for which there are no valid watermark
values before we start trying to program the hardware (although those
tests will come in a subsequent patch).
Another advantage of moving this calculation to the check phase is that
we can calculate the watermarks in a single shot as part of the atomic
transaction. The watermark interfaces we inherited from our legacy
modesetting days are a bit broken in the atomic design because they use
per-crtc entry points but actually re-calculate and re-program something
that is really more of a global state. That worked okay in the legacy
modesetting world because operations only ever updated a single CRTC at
a time. However in the atomic world, a transaction can involve multiple
CRTC's, which means we wind up computing and programming the watermarks
NxN times (where N is the number of CRTC's involved). With this patch
we eliminate the redundant re-calculation of watermark data for atomic
states (which was the cause of the WARN_ON(!wm_changed) problems that
have plagued us for a while).
We still need to work on the 'commit' side of watermark handling so that
we aren't doing redundant NxN programming of watermarks, but that's
content for future patches.
v2:
- Bail out of skl_write_wm_values() if the CRTC isn't active. Now that
we set dirty_pipes to ~0 if the active pipes change (because
we need to deal with DDB changes), we can now wind up here for
disabled pipes, whereas we couldn't before.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89055
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92181
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Tested-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463091100-13747-1-git-send-email-matthew.d.roper@intel.com
Calculate the DDB blocks needed to satisfy the current atomic
transaction at atomic check time. This is a prerequisite to calculating
SKL watermarks during the 'check' phase and rejecting any configurations
that we can't find valid watermarks for.
Due to the nature of DDB allocation, it's possible for the addition of a
new CRTC to make the watermark configuration already in use on another,
unchanged CRTC become invalid. A change in which CRTC's are active
triggers a recompute of the entire DDB, which unfortunately means we
need to disallow any other atomic commits from racing with such an
update. If the active CRTC's change, we need to grab the lock on all
CRTC's and run all CRTC's through their 'check' handler to recompute and
re-check their per-CRTC DDB allocations.
Note that with this patch we only compute the DDB allocation but we
don't actually use the computed values during watermark programming yet.
For ease of review/testing/bisecting, we still recompute the DDB at
watermark programming time and just WARN() if it doesn't match the
precomputed values. A future patch will switch over to using the
precomputed values once we're sure they're being properly computed.
Another clarifying note: DDB allocation itself shouldn't ever fail with
the algorithm we use today (i.e., we have enough DDB blocks on BXT to
support the minimum needs of the worst-case scenario of every pipe/plane
enabled at full size). However the watermarks calculations based on the
DDB may fail and we'll be moving those to the atomic check as well in
future patches.
v2:
- Skip DDB calculations in the rare case where our transaction doesn't
actually touch any CRTC's at all. Assuming at least one CRTC state
is present in our transaction, then it means we can't race with any
transactions that would update dev_priv->active_crtcs (which requires
_all_ CRTC locks).
v3:
- Also calculate DDB during initial hw readout, to prevent using
incorrect bios values. (Maarten)
v4:
- Use new distrust_bios_wm flag instead of skip_initial_wm (which was
never actually set).
- Set intel_state->active_pipe_changes instead of just realloc_pipes
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Lyude Paul <cpaul@redhat.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463061971-19638-10-git-send-email-matthew.d.roper@intel.com
Ville Syrjälä