The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The EtherAVB instances on the R-Car E3/D3 and RZ/G2E SoCs do not support
TX clock internal delay modes, and the EtherAVB driver prints a warning
if an unsupported "rgmii-*id" PHY mode is specified, to catch buggy
DTBs.
Commit a6f51f2efa ("ravb: Add support for explicit internal
clock delay configuration") deprecated deriving the internal delay mode
from the PHY mode, in favor of explicit configuration using the now
mandatory "rx-internal-delay-ps" and "tx-internal-delay-ps" properties,
thus delegating the warning to the legacy fallback code.
Since explicit configuration of a (valid) internal clock delay
configuration is enforced by validating device tree source files against
DT binding files, and all upstream DTS files have been converted as of
commit a5200e63af ("arm64: dts: renesas: rzg2: Convert EtherAVB to
explicit delay handling"), the checks in the legacy fallback code can be
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/2037542ac56e99413b9807e24049711553cc88a9.1628696778.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the member description comments for struct ravb_desc by
removing the extra TAB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to clk_disable_unprepare() can happen before priv is
initialized. This means moving clk_disable_unprepare out of
out_release into a new label.
Fixes: 8ef7adc6be ("net: ethernet: ravb: Enable optional refclk")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices that use a programmable clock for the AVB reference clock,
the driver may need to enable them. Add code to find the optional clock
and enable it when available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place the RX/TX descriptor bit *enum*s where they belong -- after the
corresponding RX/TX descriptor *struct*s and, while at it, switch to
declaring one *enum* entry per line...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename the rest of the *enum* tags still not (exactly) matching
the abbreviated register names from the manuals...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals (except R-Car gen2) the PHY status register's name
is abbreviated to PSR with the only valid bit 0 named LMON. Follow the
suit and rename the corresponding *enum* tag/entry.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals the TRSCER register bits match the corresponding
EESR registers's bits, but only on the R-Car gen2 SoC those are named
RINT<n> and TINT<n>. Follow the suit and rename the *enum* tag/entries
from DESC_I_* to TRSCER_*.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask. Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.
Fixes: 6e0bb04d0e ("sh_eth: Add R7S9210 support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d3 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff7 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wolfram reports that his R-Car H2-based Lager board can no longer be
rebooted in v5.11-rc1, as it crashes with an imprecise external abort.
The issue can be reproduced on other boards (e.g. Koelsch with R-Car
M2-W) too, if CONFIG_IP_PNP is disabled, and the Ethernet interface is
down at reboot time:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=422b6835, *pte=00000000, *ppte=00000000
Internal error: : 1406 [#1] ARM
Modules linked in:
CPU: 0 PID: 1105 Comm: init Tainted: G W 5.10.0-rc1-00402-ge2f016cf7751 #1048
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
PC is at sh_mdio_ctrl+0x44/0x60
LR is at sh_mmd_ctrl+0x20/0x24
...
Backtrace:
[<c0451f30>] (sh_mdio_ctrl) from [<c0451fd4>] (sh_mmd_ctrl+0x20/0x24)
r7:0000001f r6:00000020 r5:00000002 r4:c22a1dc4
[<c0451fb4>] (sh_mmd_ctrl) from [<c044fc18>] (mdiobb_cmd+0x38/0xa8)
[<c044fbe0>] (mdiobb_cmd) from [<c044feb8>] (mdiobb_read+0x58/0xdc)
r9:c229f844 r8:c0c329dc r7:c221e000 r6:00000001 r5:c22a1dc4 r4:00000001
[<c044fe60>] (mdiobb_read) from [<c044c854>] (__mdiobus_read+0x74/0xe0)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e000
[<c044c7e0>] (__mdiobus_read) from [<c044c9d8>] (mdiobus_read+0x40/0x54)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e458
[<c044c998>] (mdiobus_read) from [<c044d678>] (phy_read+0x1c/0x20)
r7:ffffe000 r6:c221e470 r5:00000200 r4:c229f800
[<c044d65c>] (phy_read) from [<c044d94c>] (kszphy_config_intr+0x44/0x80)
[<c044d908>] (kszphy_config_intr) from [<c044694c>] (phy_disable_interrupts+0x44/0x50)
r5:c229f800 r4:c229f800
[<c0446908>] (phy_disable_interrupts) from [<c0449370>] (phy_shutdown+0x18/0x1c)
r5:c229f800 r4:c229f804
[<c0449358>] (phy_shutdown) from [<c040066c>] (device_shutdown+0x168/0x1f8)
[<c0400504>] (device_shutdown) from [<c013de44>] (kernel_restart_prepare+0x3c/0x48)
r9:c22d2000 r8:c0100264 r7:c0b0d034 r6:00000000 r5:4321fedc r4:00000000
[<c013de08>] (kernel_restart_prepare) from [<c013dee0>] (kernel_restart+0x1c/0x60)
[<c013dec4>] (kernel_restart) from [<c013e1d8>] (__do_sys_reboot+0x168/0x208)
r5:4321fedc r4:01234567
[<c013e070>] (__do_sys_reboot) from [<c013e2e8>] (sys_reboot+0x18/0x1c)
r7:00000058 r6:00000000 r5:00000000 r4:00000000
[<c013e2d0>] (sys_reboot) from [<c0100060>] (ret_fast_syscall+0x0/0x54)
As of commit e2f016cf77 ("net: phy: add a shutdown procedure"),
system reboot calls phy_disable_interrupts() during shutdown. As this
happens unconditionally, the PHY registers may be accessed while the
device is suspended, causing undefined behavior, which may crash the
system.
Fix this by wrapping the PHY bitbang accessors in the sh_eth driver by
wrappers that take care of Runtime PM, to resume the device when needed.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "undocumented" annotations in the EtherAVB driver were done against
the R-Car gen2 manuals; most of these registers/bits were then described
in the R-Car gen3 manuals -- reflect this fact in the annotations (note
that ECSIPR.LCHNGIP was documented in the recent R-Car gen2 manual)...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the R-Car Series, 3rd Generation User's Manual: Hardware,
Rev. 1.50, there's no APSR.DM field, instead there are 2 independent
RX/TX clock internal delay bits. Follow the suit: remove #define APSR_DM
and rename #define's APSR_DM_{R|T}DM to APSR_{R|T}DM.
While at it, do several more things to the declaration of *enum* APSR_BIT:
- remove superfluous indentation;
- annotate APSR_MEMS as undocumented;
- annotate APSR as R-Car Gen3 only.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some EtherAVB variants support internal clock delay configuration, which
can add larger delays than the delays that are typically supported by
the PHY (using an "rgmii-*id" PHY mode, and/or "[rt]xc-skew-ps"
properties).
Historically, the EtherAVB driver configured these delays based on the
"rgmii-*id" PHY mode. This caused issues with PHY drivers that
implement PHY internal delays properly[1]. Hence a backwards-compatible
workaround was added by masking the PHY mode[2].
Add proper support for explicit configuration of the MAC internal clock
delays using the new "[rt]x-internal-delay-ps" properties.
Fall back to the old handling if none of these properties is present.
[1] Commit bcf3440c6d ("net: phy: micrel: add phy-mode support for
the KSZ9031 PHY")
[2] Commit 9b23203c32 ("ravb: Mask PHY mode to avoid inserting
delays twice").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, full delay handling is done in both the probe and resume
paths. Split it in two parts, so the resume path doesn't have to redo
the parsing part over and over again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While fixing the W=1 builds, this warning came up because the
developers used a very tricky way to get structures initialized
to a non-zero value, but this causes GCC to warn about an
override. In this case the override was intentional, so just
disable the warning for this code with a kernel macro that results
in disabling the warning for compiles on GCC versions after 8.
It is not appropriate to change the struct to initialize all the
values as it will just add a lot more code for no value. The code
is completely correct as is, we just want to acknowledge that
this code could generate a warning and we're ok with that.
NOTE: the __diag_ignore macro currently only accepts a second
argument of 8 (version 80000), it's either use this one or
open code the pragma.
Fixed Warnings example (all the same):
drivers/net/ethernet/renesas/sh_eth.c:51:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:52:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:53:13: warning: initialized field overwritten [-Woverride-init]
+ 256 more...
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1838d6c62f.
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
dpm_resume+0x128/0x4f8
device_resume+0xcc/0x1b0
dpm_run_callback+0x74/0x340
ravb_resume+0x190/0x1b8
ravb_open+0x84/0x770
of_mdiobus_register+0x1e0/0x468
of_mdiobus_register_phy+0x1b8/0x250
of_mdiobus_phy_device_register+0x178/0x1e8
phy_device_register+0x114/0x1b8
device_add+0x3d4/0x798
bus_probe_device+0x98/0xa0
device_initial_probe+0x10/0x18
__device_attach+0xe4/0x140
bus_for_each_drv+0x64/0xc8
__device_attach_driver+0xb8/0xe0
driver_probe_device.part.11+0xc4/0xd8
really_probe+0x32c/0x3b8
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425a ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only usage of bb_ops is to assign its address to the ops field in
the mdiobb_ctrl struct, which is a const pointer. Make it const to allow
the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When this driver is built as a module, I cannot rmmod it after insmoding
it.
This is because that this driver calls ravb_mdio_init() at the time of
probe, and module->refcnt is incremented by alloc_mdio_bitbang() called
after that.
Therefore, even if ifup is not performed, the driver is in use and rmmod
cannot be performed.
$ lsmod
Module Size Used by
ravb 40960 1
$ rmmod ravb
rmmod: ERROR: Module ravb is in use
Call ravb_mdio_init() at open and free_mdio_bitbang() at close, thereby
rmmod is possible in the ifdown state.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yuusuke Ashizuka <ashiduka@fujitsu.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().
ravb e6800000.ethernet ethernet: failed to switch device to config mode
This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().
To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.
[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode
("RGMII-*ID") settings, but used the hardware defaults, augmented by
explicit configuration of individual skew values using the "*-skew-ps"
DT properties. The lack of PHY mode support was compensated by the
EtherAVB MAC driver, which configures TX and/or RX internal delay
itself, based on the PHY mode.
However, now the KSZ9031 driver has gained PHY mode support, delays may
be configured twice, causing regressions. E.g. on the Renesas
Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca.
400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp.
As internal delay configuration supported by the KSZ9031 PHY is too
limited for some use cases, the ability to configure MAC internal delay
is deemed useful and necessary. Hence a proper fix would involve
splitting internal delay configuration in two parts, one for the PHY,
and one for the MAC. However, this would require adding new DT
properties, thus breaking DTB backwards-compatibility.
Hence fix the regression in a backwards-compatibility way, by letting
the EtherAVB driver mask the PHY mode when it has inserted a delay, to
avoid the PHY driver adding a second delay. This also fixes messages
like:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii"
as the PHY no longer sees the original RGMII-*ID mode.
Solving the issue by splitting configuration in two parts can be handled
in future patches, and would require retaining a backwards-compatibility
mode anyway.
Fixes: bcf3440c6d ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register maps for the Gigabit controllers and the Ether one used on
RZ/A1 (AKA R7S72100) are identical except for GECMR which is only present
on the true GEther controllers. We no longer use the register map arrays
to determine if a given register exists, and have added the GECMR flag to
the 'struct sh_eth_cpu_data' in the previous patch, so we're ready to drop
the R7S72100 specific register map -- this saves 216 bytes of object code
(ARM gcc 4.8.5).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all Ether controllers having the Gigabit register layout have GECMR --
RZ/A1 (AKA R7S72100) actually has the same layout but no Gigabit speed
support and hence no GECMR. In the past, the new register map table was
added for this SoC, now I think we should have used the existing Gigabit
table with the differences (such as GECMR) covered by the mere flags in
the 'struct sh_eth_cpu_data'. Add such flag for GECMR -- and then we can
get rid of the R7S72100 specific layout in the next patch...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::no_xdfar flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RDFAR/TDFAR to be
considered for dumping on the R-Car gen1/2 SoCs (the register offset check
has the final say here)...
Fixes: 4c1d45850d ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::cexcr flag I forgot to add the flag
check to __sh_eth_get_regs(), causing the non-existing RX packet counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: 4c1d45850d ("sh_eth: add sh_eth_cpu_data::cexcr flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::no_tx_cntrs flag I forgot to add the
flag check to __sh_eth_get_regs(), causing the non-existing TX counter
registers to be considered for dumping on the R7S72100 SoC (the register
offset sanity check has the final say here)...
Fixes: ce9134dff6 ("sh_eth: add sh_eth_cpu_data::no_tx_cntrs flag")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann