This commit fixes a bug in the tracking of max_packets_out and
is_cwnd_limited. This bug can cause the connection to fail to remember
that is_cwnd_limited is true, causing the connection to fail to grow
cwnd when it should, causing throughput to be lower than it should be.
The following event sequence is an example that triggers the bug:
(a) The connection is cwnd_limited, but packets_out is not at its
peak due to TSO deferral deciding not to send another skb yet.
In such cases the connection can advance max_packets_seq and set
tp->is_cwnd_limited to true and max_packets_out to a small
number.
(b) Then later in the round trip the connection is pacing-limited (not
cwnd-limited), and packets_out is larger. In such cases the
connection would raise max_packets_out to a bigger number but
(unexpectedly) flip tp->is_cwnd_limited from true to false.
This commit fixes that bug.
One straightforward fix would be to separately track (a) the next
window after max_packets_out reaches a maximum, and (b) the next
window after tp->is_cwnd_limited is set to true. But this would
require consuming an extra u32 sequence number.
Instead, to save space we track only the most important
information. Specifically, we track the strongest available signal of
the degree to which the cwnd is fully utilized:
(1) If the connection is cwnd-limited then we remember that fact for
the current window.
(2) If the connection not cwnd-limited then we track the maximum
number of outstanding packets in the current window.
In particular, note that the new logic cannot trigger the buggy
(a)/(b) sequence above because with the new logic a condition where
tp->packets_out > tp->max_packets_out can only trigger an update of
tp->is_cwnd_limited if tp->is_cwnd_limited is false.
This first showed up in a testing of a BBRv2 dev branch, but this
buggy behavior highlighted a general issue with the
tcp_cwnd_validate() logic that can cause cwnd to fail to increase at
the proper rate for any TCP congestion control, including Reno or
CUBIC.
Fixes: ca8a226343 ("tcp: make cwnd-limited checks measurement-based, and gentler")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be used to support TCP FastOpen with MPTCP in the following
commit.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Dmytro Shytyi <dmytro@shytyi.net>
Signed-off-by: Dmytro Shytyi <dmytro@shytyi.net>
Signed-off-by: Benjamin Hesmans <benjamin.hesmans@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While destroying netns, we call inet_twsk_purge() in tcp_sk_exit_batch()
and tcpv6_net_exit_batch() for AF_INET and AF_INET6. These commands
trigger the kernel to walk through the potentially big ehash twice even
though the netns has no TIME_WAIT sockets.
# ip netns add test
# ip netns del test
or
# unshare -n /bin/true >/dev/null
When tw_refcount is 1, we need not call inet_twsk_purge() at least
for the net. We can save such unneeded iterations if all netns in
net_exit_list have no TIME_WAIT sockets. This change eliminates
the tax by the additional unshare() described in the next patch to
guarantee the per-netns ehash size.
Tested:
# mount -t debugfs none /sys/kernel/debug/
# echo cleanup_net > /sys/kernel/debug/tracing/set_ftrace_filter
# echo inet_twsk_purge >> /sys/kernel/debug/tracing/set_ftrace_filter
# echo function > /sys/kernel/debug/tracing/current_tracer
# cat ./add_del_unshare.sh
for i in `seq 1 40`
do
(for j in `seq 1 100` ; do unshare -n /bin/true >/dev/null ; done) &
done
wait;
# ./add_del_unshare.sh
Before the patch:
# cat /sys/kernel/debug/tracing/trace_pipe
kworker/u128:0-8 [031] ...1. 174.162765: cleanup_net <-process_one_work
kworker/u128:0-8 [031] ...1. 174.240796: inet_twsk_purge <-cleanup_net
kworker/u128:0-8 [032] ...1. 174.244759: inet_twsk_purge <-tcp_sk_exit_batch
kworker/u128:0-8 [034] ...1. 174.290861: cleanup_net <-process_one_work
kworker/u128:0-8 [039] ...1. 175.245027: inet_twsk_purge <-cleanup_net
kworker/u128:0-8 [046] ...1. 175.290541: inet_twsk_purge <-tcp_sk_exit_batch
kworker/u128:0-8 [037] ...1. 175.321046: cleanup_net <-process_one_work
kworker/u128:0-8 [024] ...1. 175.941633: inet_twsk_purge <-cleanup_net
kworker/u128:0-8 [025] ...1. 176.242539: inet_twsk_purge <-tcp_sk_exit_batch
After:
# cat /sys/kernel/debug/tracing/trace_pipe
kworker/u128:0-8 [038] ...1. 428.116174: cleanup_net <-process_one_work
kworker/u128:0-8 [038] ...1. 428.262532: cleanup_net <-process_one_work
kworker/u128:0-8 [030] ...1. 429.292645: cleanup_net <-process_one_work
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch changes bpf_getsockopt(SOL_TCP) to reuse
do_tcp_getsockopt(). It removes the duplicated code from
bpf_getsockopt(SOL_TCP).
Before this patch, there were some optnames available to
bpf_setsockopt(SOL_TCP) but missing in bpf_getsockopt(SOL_TCP).
For example, TCP_NODELAY, TCP_MAXSEG, TCP_KEEPIDLE, TCP_KEEPINTVL,
and a few more. It surprises users from time to time. This patch
automatically closes this gap without duplicating more code.
bpf_getsockopt(TCP_SAVED_SYN) does not free the saved_syn,
so it stays in sol_tcp_sockopt().
For string name value like TCP_CONGESTION, bpf expects it
is always null terminated, so sol_tcp_sockopt() decrements
optlen by one before calling do_tcp_getsockopt() and
the 'if (optlen < saved_optlen) memset(..,0,..);'
in __bpf_getsockopt() will always do a null termination.
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://lore.kernel.org/r/20220902002918.2894511-1-kafai@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
After the prep work in the previous patches,
this patch removes all the dup code from bpf_setsockopt(SOL_TCP)
and reuses the do_tcp_setsockopt().
The existing optname white-list is refactored into a new
function sol_tcp_setsockopt(). The sol_tcp_setsockopt()
also calls the bpf_sol_tcp_setsockopt() to handle
the TCP_BPF_XXX specific optnames.
bpf_setsockopt(TCP_SAVE_SYN) now also allows a value 2 to
save the eth header also and it comes for free from
do_tcp_setsockopt().
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/r/20220817061819.4180146-1-kafai@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Expose TCP rx queue accessor and cleanup, so that TLS can
decrypt directly from the TCP queue. The expectation
is that the caller can access the skb returned from
tcp_recv_skb() and up to inq bytes worth of data (some
of which may be in ->next skbs) and then call
tcp_read_done() when data has been consumed.
The socket lock must be held continuously across
those two operations.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While reading sysctl_tcp_adv_win_scale, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_slow_start_after_idle, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: 35089bb203 ("[TCP]: Add tcp_slow_start_after_idle sysctl.")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_notsent_lowat, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: c9bee3b7fd ("tcp: TCP_NOTSENT_LOWAT socket option")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading these sysctl knobs, they can be changed concurrently.
Thus, we need to add READ_ONCE() to their readers.
- tcp_retries1
- tcp_retries2
- tcp_orphan_retries
- tcp_fin_timeout
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While reading sysctl_tcp_keepalive_(time|probes|intvl), they can be changed
concurrently. Thus, we need to add READ_ONCE() to their readers.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e21145a987 ("ipv4: namespacify ip_early_demux sysctl knob") made
it possible to enable/disable early_demux on a per-netns basis. Then, we
introduced two knobs, tcp_early_demux and udp_early_demux, to switch it for
TCP/UDP in commit dddb64bcb3 ("net: Add sysctl to toggle early demux for
tcp and udp"). However, the .proc_handler() was wrong and actually
disabled us from changing the behaviour in each netns.
We can execute early_demux if net.ipv4.ip_early_demux is on and each proto
.early_demux() handler is not NULL. When we toggle (tcp|udp)_early_demux,
the change itself is saved in each netns variable, but the .early_demux()
handler is a global variable, so the handler is switched based on the
init_net's sysctl variable. Thus, netns (tcp|udp)_early_demux knobs have
nothing to do with the logic. Whether we CAN execute proto .early_demux()
is always decided by init_net's sysctl knob, and whether we DO it or not is
by each netns ip_early_demux knob.
This patch namespacifies (tcp|udp)_early_demux again. For now, the users
of the .early_demux() handler are TCP and UDP only, and they are called
directly to avoid retpoline. So, we can remove the .early_demux() handler
from inet6?_protos and need not dereference them in ip6?_rcv_finish_core().
If another proto needs .early_demux(), we can restore it at that time.
Fixes: dddb64bcb3 ("net: Add sysctl to toggle early demux for tcp and udp")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20220713175207.7727-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently both splice() and sockmap use ->read_sock() to
read skb from receive queue, but for sockmap we only read
one entire skb at a time, so ->read_sock() is too conservative
to use. Introduce a new proto_ops ->read_skb() which supports
this sematic, with this we can finally pass the ownership of
skb to recv actors.
For non-TCP protocols, all ->read_sock() can be simply
converted to ->read_skb().
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220615162014.89193-3-xiyou.wangcong@gmail.com
This patch inroduces tcp_read_skb() based on tcp_read_sock(),
a preparation for the next patch which actually introduces
a new sock ops.
TCP is special here, because it has tcp_read_sock() which is
mainly used by splice(). tcp_read_sock() supports partial read
and arbitrary offset, neither of them is needed for sockmap.
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220615162014.89193-2-xiyou.wangcong@gmail.com
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-06-17
We've added 72 non-merge commits during the last 15 day(s) which contain
a total of 92 files changed, 4582 insertions(+), 834 deletions(-).
The main changes are:
1) Add 64 bit enum value support to BTF, from Yonghong Song.
2) Implement support for sleepable BPF uprobe programs, from Delyan Kratunov.
3) Add new BPF helpers to issue and check TCP SYN cookies without binding to a
socket especially useful in synproxy scenarios, from Maxim Mikityanskiy.
4) Fix libbpf's internal USDT address translation logic for shared libraries as
well as uprobe's symbol file offset calculation, from Andrii Nakryiko.
5) Extend libbpf to provide an API for textual representation of the various
map/prog/attach/link types and use it in bpftool, from Daniel Müller.
6) Provide BTF line info for RV64 and RV32 JITs, and fix a put_user bug in the
core seen in 32 bit when storing BPF function addresses, from Pu Lehui.
7) Fix libbpf's BTF pointer size guessing by adding a list of various aliases
for 'long' types, from Douglas Raillard.
8) Fix bpftool to readd setting rlimit since probing for memcg-based accounting
has been unreliable and caused a regression on COS, from Quentin Monnet.
9) Fix UAF in BPF cgroup's effective program computation triggered upon BPF link
detachment, from Tadeusz Struk.
10) Fix bpftool build bootstrapping during cross compilation which was pointing
to the wrong AR process, from Shahab Vahedi.
11) Fix logic bug in libbpf's is_pow_of_2 implementation, from Yuze Chi.
12) BPF hash map optimization to avoid grabbing spinlocks of all CPUs when there
is no free element. Also add a benchmark as reproducer, from Feng Zhou.
13) Fix bpftool's codegen to bail out when there's no BTF, from Michael Mullin.
14) Various minor cleanup and improvements all over the place.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (72 commits)
bpf: Fix bpf_skc_lookup comment wrt. return type
bpf: Fix non-static bpf_func_proto struct definitions
selftests/bpf: Don't force lld on non-x86 architectures
selftests/bpf: Add selftests for raw syncookie helpers in TC mode
bpf: Allow the new syncookie helpers to work with SKBs
selftests/bpf: Add selftests for raw syncookie helpers
bpf: Add helpers to issue and check SYN cookies in XDP
bpf: Allow helpers to accept pointers with a fixed size
bpf: Fix documentation of th_len in bpf_tcp_{gen,check}_syncookie
selftests/bpf: add tests for sleepable (uk)probes
libbpf: add support for sleepable uprobe programs
bpf: allow sleepable uprobe programs to attach
bpf: implement sleepable uprobes by chaining gps
bpf: move bpf_prog to bpf.h
libbpf: Fix internal USDT address translation logic for shared libraries
samples/bpf: Check detach prog exist or not in xdp_fwd
selftests/bpf: Avoid skipping certain subtests
selftests/bpf: Fix test_varlen verification failure with latest llvm
bpftool: Do not check return value from libbpf_set_strict_mode()
Revert "bpftool: Use libbpf 1.0 API mode instead of RLIMIT_MEMLOCK"
...
====================
Link: https://lore.kernel.org/r/20220617220836.7373-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The new helpers bpf_tcp_raw_{gen,check}_syncookie_ipv{4,6} allow an XDP
program to generate SYN cookies in response to TCP SYN packets and to
check those cookies upon receiving the first ACK packet (the final
packet of the TCP handshake).
Unlike bpf_tcp_{gen,check}_syncookie these new helpers don't need a
listening socket on the local machine, which allows to use them together
with synproxy to accelerate SYN cookie generation.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220615134847.3753567-4-maximmi@nvidia.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Each protocol having a ->memory_allocated pointer gets a corresponding
per-cpu reserve, that following patches will use.
Instead of having reserved bytes per socket,
we want to have per-cpu reserves.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Logic added in commit f35f821935 ("tcp: defer skb freeing after socket
lock is released") helped bulk TCP flows to move the cost of skbs
frees outside of critical section where socket lock was held.
But for RPC traffic, or hosts with RFS enabled, the solution is far from
being ideal.
For RPC traffic, recvmsg() has to return to user space right after
skb payload has been consumed, meaning that BH handler has no chance
to pick the skb before recvmsg() thread. This issue is more visible
with BIG TCP, as more RPC fit one skb.
For RFS, even if BH handler picks the skbs, they are still picked
from the cpu on which user thread is running.
Ideally, it is better to free the skbs (and associated page frags)
on the cpu that originally allocated them.
This patch removes the per socket anchor (sk->defer_list) and
instead uses a per-cpu list, which will hold more skbs per round.
This new per-cpu list is drained at the end of net_action_rx(),
after incoming packets have been processed, to lower latencies.
In normal conditions, skbs are added to the per-cpu list with
no further action. In the (unlikely) cases where the cpu does not
run net_action_rx() handler fast enough, we use an IPI to raise
NET_RX_SOFTIRQ on the remote cpu.
Also, we do not bother draining the per-cpu list from dev_cpu_dead()
This is because skbs in this list have no requirement on how fast
they should be freed.
Note that we can add in the future a small per-cpu cache
if we see any contention on sd->defer_lock.
Tested on a pair of hosts with 100Gbit NIC, RFS enabled,
and /proc/sys/net/ipv4/tcp_rmem[2] tuned to 16MB to work around
page recycling strategy used by NIC driver (its page pool capacity
being too small compared to number of skbs/pages held in sockets
receive queues)
Note that this tuning was only done to demonstrate worse
conditions for skb freeing for this particular test.
These conditions can happen in more general production workload.
10 runs of one TCP_STREAM flow
Before:
Average throughput: 49685 Mbit.
Kernel profiles on cpu running user thread recvmsg() show high cost for
skb freeing related functions (*)
57.81% [kernel] [k] copy_user_enhanced_fast_string
(*) 12.87% [kernel] [k] skb_release_data
(*) 4.25% [kernel] [k] __free_one_page
(*) 3.57% [kernel] [k] __list_del_entry_valid
1.85% [kernel] [k] __netif_receive_skb_core
1.60% [kernel] [k] __skb_datagram_iter
(*) 1.59% [kernel] [k] free_unref_page_commit
(*) 1.16% [kernel] [k] __slab_free
1.16% [kernel] [k] _copy_to_iter
(*) 1.01% [kernel] [k] kfree
(*) 0.88% [kernel] [k] free_unref_page
0.57% [kernel] [k] ip6_rcv_core
0.55% [kernel] [k] ip6t_do_table
0.54% [kernel] [k] flush_smp_call_function_queue
(*) 0.54% [kernel] [k] free_pcppages_bulk
0.51% [kernel] [k] llist_reverse_order
0.38% [kernel] [k] process_backlog
(*) 0.38% [kernel] [k] free_pcp_prepare
0.37% [kernel] [k] tcp_recvmsg_locked
(*) 0.37% [kernel] [k] __list_add_valid
0.34% [kernel] [k] sock_rfree
0.34% [kernel] [k] _raw_spin_lock_irq
(*) 0.33% [kernel] [k] __page_cache_release
0.33% [kernel] [k] tcp_v6_rcv
(*) 0.33% [kernel] [k] __put_page
(*) 0.29% [kernel] [k] __mod_zone_page_state
0.27% [kernel] [k] _raw_spin_lock
After patch:
Average throughput: 73076 Mbit.
Kernel profiles on cpu running user thread recvmsg() looks better:
81.35% [kernel] [k] copy_user_enhanced_fast_string
1.95% [kernel] [k] _copy_to_iter
1.95% [kernel] [k] __skb_datagram_iter
1.27% [kernel] [k] __netif_receive_skb_core
1.03% [kernel] [k] ip6t_do_table
0.60% [kernel] [k] sock_rfree
0.50% [kernel] [k] tcp_v6_rcv
0.47% [kernel] [k] ip6_rcv_core
0.45% [kernel] [k] read_tsc
0.44% [kernel] [k] _raw_spin_lock_irqsave
0.37% [kernel] [k] _raw_spin_lock
0.37% [kernel] [k] native_irq_return_iret
0.33% [kernel] [k] __inet6_lookup_established
0.31% [kernel] [k] ip6_protocol_deliver_rcu
0.29% [kernel] [k] tcp_rcv_established
0.29% [kernel] [k] llist_reverse_order
v2: kdoc issue (kernel bots)
do not defer if (alloc_cpu == smp_processor_id()) (Paolo)
replace the sk_buff_head with a single-linked list (Jakub)
add a READ_ONCE()/WRITE_ONCE() for the lockless read of sd->defer_list
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/20220422201237.416238-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit
0cbe6a8f08 ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
Before patch:
$ bench_rr.sh
130000000
80000000
140000000
140000000
140000000
140000000
130000000
40000000
90000000
110000000
SUM=1140000000
After patch:
$ bench_rr.sh
430000000
590000000
530000000
450000000
450000000
350000000
450000000
490000000
480000000
460000000
SUM=4680000000 # This is 410 % of the value before patch.
Fixes: c9bee3b7fd ("tcp: TCP_NOTSENT_LOWAT socket option")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Doug Porter <dsp@fb.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ACK (s)acks multiple skbs, we favor the information
from the most recently sent skb by choosing the skb with
the highest prior_delivered count. But in the interval
between receiving ACKs, we send multiple skbs with the same
prior_delivered, because the tp->delivered only changes
when we receive an ACK.
We used RACK's solution, copying tcp_rack_sent_after() as
tcp_skb_sent_after() helper to determine "which packet was
sent last?". Later, we will use tcp_skb_sent_after() instead
in RACK.
Fixes: b9f64820fb ("tcp: track data delivery rate for a TCP connection")
Signed-off-by: Pengcheng Yang <yangpc@wangsu.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/1650422081-22153-1-git-send-email-yangpc@wangsu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The internal recvmsg() functions have two parameters 'flags' and 'noblock'
that were merged inside skb_recv_datagram(). As a follow up patch to commit
f4b41f062c ("net: remove noblock parameter from skb_recv_datagram()")
this patch removes the separate 'noblock' parameter for recvmsg().
Analogue to the referenced patch for skb_recv_datagram() the 'flags' and
'noblock' parameters are unnecessarily split up with e.g.
err = sk->sk_prot->recvmsg(sk, msg, size, flags & MSG_DONTWAIT,
flags & ~MSG_DONTWAIT, &addr_len);
or in
err = INDIRECT_CALL_2(sk->sk_prot->recvmsg, tcp_recvmsg, udp_recvmsg,
sk, msg, size, flags & MSG_DONTWAIT,
flags & ~MSG_DONTWAIT, &addr_len);
instead of simply using only flags all the time and check for MSG_DONTWAIT
where needed (to preserve for the formerly separated no(n)block condition).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20220411124955.154876-1-socketcan@hartkopp.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The congestion status of a tcp flow may be updated since there
is congestion between tcp sender and receiver. It makes sense to
add tracepoint for congestion status set function to summate cc
status duration and evaluate the performance of network
and congestion algorithm. the backgound of this patch is below.
Link: https://github.com/iovisor/bcc/pull/3899
Signed-off-by: Ping Gan <jacky_gam_2001@163.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220406010956.19656-1-jacky_gam_2001@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We had various bugs over the years with code
breaking the assumption that tp->snd_cwnd is greater
than zero.
Lately, syzbot reported the WARN_ON_ONCE(!tp->prior_cwnd) added
in commit 8b8a321ff7 ("tcp: fix zero cwnd in tcp_cwnd_reduction")
can trigger, and without a repro we would have to spend
considerable time finding the bug.
Instead of complaining too late, we want to catch where
and when tp->snd_cwnd is set to an illegal value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Link: https://lore.kernel.org/r/20220405233538.947344-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When CONFIG_TCP_MD5SIG isn't enabled, there is a compilation bug due to
the fact that the static inline definition of tcp_inbound_md5_hash() has
an unexpected semicolon. Remove it.
Fixes: 1330b6ef33 ("skb: make drop reason booleanable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220309122012.668986-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have a number of cases where function returns drop/no drop
decision as a boolean. Now that we want to report the reason
code as well we have to pass extra output arguments.
We can make the reason code evaluate correctly as bool.
I believe we're good to reorder the reasons as they are
reported to user space as strings.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions do essentially the same work to verify TCP-MD5 sign.
Code can be merged into one family-independent function in order to
reduce copy'n'paste and generated code.
Later with TCP-AO option added, this will allow to create one function
that's responsible for segment verification, that will have all the
different checks for MD5/AO/non-signed packets, which in turn will help
to see checks for all corner-cases in one function, rather than spread
around different families and functions.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220223175740.452397-1-dima@arista.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass the address of drop_reason to tcp_add_backlog() to store the
reasons for skb drops when fails. Following drop reasons are
introduced:
SKB_DROP_REASON_SOCKET_BACKLOG
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Reviewed-by: Hao Peng <flyingpeng@tencent.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting RTO through BPF program, some SYN ACK packets were unaffected
and continued to use TCP_TIMEOUT_INIT constant. This patch adds timeout
option to struct request_sock. Option is initialized with TCP_TIMEOUT_INIT
and is reassigned through BPF using tcp_timeout_init call. SYN ACK
retransmits now use newly added timeout option.
Signed-off-by: Akhmat Karakotov <hmukos@yandex-team.ru>
Acked-by: Martin KaFai Lau <kafai@fb.com>
v2:
- Add timeout option to struct request_sock. Do not call
tcp_timeout_init on every syn ack retransmit.
v3:
- Use unsigned long for min. Bound tcp_timeout_init to TCP_RTO_MAX.
v4:
- Refactor duplicate code by adding reqsk_timeout function.
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling the kernel with CONFIG_INET disabled, the
sk_defer_free_flush() should be defined as a nop.
This resolves the following compilation error:
ld: net/core/sock.o: in function `sk_defer_free_flush':
./include/net/tcp.h:1378: undefined reference to `__sk_defer_free_flush'
Fixes: 79074a72d3 ("net: Flush deferred skb free on socket destroy")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220120123440.9088-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tcp recvmsg() (or rx zerocopy) spends a fair amount of time
freeing skbs after their payload has been consumed.
A typical ~64KB GRO packet has to release ~45 page
references, eventually going to page allocator
for each of them.
Currently, this freeing is performed while socket lock
is held, meaning that there is a high chance that
BH handler has to queue incoming packets to tcp socket backlog.
This can cause additional latencies, because the user
thread has to process the backlog at release_sock() time,
and while doing so, additional frames can be added
by BH handler.
This patch adds logic to defer these frees after socket
lock is released, or directly from BH handler if possible.
Being able to free these skbs from BH handler helps a lot,
because this avoids the usual alloc/free assymetry,
when BH handler and user thread do not run on same cpu or
NUMA node.
One cpu can now be fully utilized for the kernel->user copy,
and another cpu is handling BH processing and skb/page
allocs/frees (assuming RFS is not forcing use of a single CPU)
Tested:
100Gbit NIC
Max throughput for one TCP_STREAM flow, over 10 runs
MTU : 1500
Before: 55 Gbit
After: 66 Gbit
MTU : 4096+(headers)
Before: 82 Gbit
After: 95 Gbit
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_segs_in() can be called from BH, while socket spinlock
is held but socket owned by user, eventually reading these
fields from tcp_get_info()
Found by code inspection, no need to backport this patch
to older kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track skbs containing only zerocopy data and avoid charging them to
kernel memory to correctly account the memory utilization for
msg_zerocopy. All of the data in such skbs is held in user pages which
are already accounted to user. Before this change, they are charged
again in kernel in __zerocopy_sg_from_iter. The charging in kernel is
excessive because data is not being copied into skb frags. This
excessive charging can lead to kernel going into memory pressure
state which impacts all sockets in the system adversely. Mark pure
zerocopy skbs with a SKBFL_PURE_ZEROCOPY flag and remove
charge/uncharge for data in such skbs.
Initially, an skb is marked pure zerocopy when it is empty and in
zerocopy path. skb can then change from a pure zerocopy skb to mixed
data skb (zerocopy and copy data) if it is at tail of write queue and
there is room available in it and non-zerocopy data is being sent in
the next sendmsg call. At this time sk_mem_charge is done for the pure
zerocopied data and the pure zerocopy flag is unmarked. We found that
this happens very rarely on workloads that pass MSG_ZEROCOPY.
A pure zerocopy skb can later be coalesced into normal skb if they are
next to each other in queue but this patch prevents coalescing from
happening. This avoids complexity of charging when skb downgrades from
pure zerocopy to mixed. This is also rare.
In sk_wmem_free_skb, if it is a pure zerocopy skb, an sk_mem_uncharge
for SKB_TRUESIZE(skb_end_offset(skb)) is done for sk_mem_charge in
tcp_skb_entail for an skb without data.
Testing with the msg_zerocopy.c benchmark between two hosts(100G nics)
with zerocopy showed that before this patch the 'sock' variable in
memory.stat for cgroup2 that tracks sum of sk_forward_alloc,
sk_rmem_alloc and sk_wmem_queued is around 1822720 and with this
change it is 0. This is due to no charge to sk_forward_alloc for
zerocopy data and shows memory utilization for kernel is lowered.
With this commit we don't see the warning we saw in previous commit
which resulted in commit 84882cf72c.
Signed-off-by: Talal Ahmad <talalahmad@google.com>
Acked-by: Arjun Roy <arjunroy@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track skbs with only zerocopy data and avoid charging them to kernel
memory to correctly account the memory utilization for msg_zerocopy.
All of the data in such skbs is held in user pages which are already
accounted to user. Before this change, they are charged again in
kernel in __zerocopy_sg_from_iter. The charging in kernel is
excessive because data is not being copied into skb frags. This
excessive charging can lead to kernel going into memory pressure
state which impacts all sockets in the system adversely. Mark pure
zerocopy skbs with a SKBFL_PURE_ZEROCOPY flag and remove
charge/uncharge for data in such skbs.
Initially, an skb is marked pure zerocopy when it is empty and in
zerocopy path. skb can then change from a pure zerocopy skb to mixed
data skb (zerocopy and copy data) if it is at tail of write queue and
there is room available in it and non-zerocopy data is being sent in
the next sendmsg call. At this time sk_mem_charge is done for the pure
zerocopied data and the pure zerocopy flag is unmarked. We found that
this happens very rarely on workloads that pass MSG_ZEROCOPY.
A pure zerocopy skb can later be coalesced into normal skb if they are
next to each other in queue but this patch prevents coalescing from
happening. This avoids complexity of charging when skb downgrades from
pure zerocopy to mixed. This is also rare.
In sk_wmem_free_skb, if it is a pure zerocopy skb, an sk_mem_uncharge
for SKB_TRUESIZE(MAX_TCP_HEADER) is done for sk_mem_charge in
tcp_skb_entail for an skb without data.
Testing with the msg_zerocopy.c benchmark between two hosts(100G nics)
with zerocopy showed that before this patch the 'sock' variable in
memory.stat for cgroup2 that tracks sum of sk_forward_alloc,
sk_rmem_alloc and sk_wmem_queued is around 1822720 and with this
change it is 0. This is due to no charge to sk_forward_alloc for
zerocopy data and shows memory utilization for kernel is lowered.
Signed-off-by: Talal Ahmad <talalahmad@google.com>
Acked-by: Arjun Roy <arjunroy@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sk_wmem_free_skb() is only used by TCP.
Rename it to make this clear, and move its declaration to
include/net/tcp.h
Signed-off-by: Talal Ahmad <talalahmad@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Arjun Roy <arjunroy@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All tcp_remove_empty_skb() callers now use tcp_write_queue_tail()
for the skb argument, we can therefore factorize code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_stream_alloc_skb() is only used by TCP.
Rename it to make this clear, and move its declaration
to include/net/tcp.h
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple VRFs are generally meant to be "separate" but right now md5
keys for the default VRF also affect connections inside VRFs if the IP
addresses happen to overlap.
So far the combination of TCP_MD5SIG_FLAG_IFINDEX with tcpm_ifindex == 0
was an error, accept this to mean "key only applies to default VRF".
This is what applications using VRFs for traffic separation want.
Signed-off-by: Leonard Crestez <cdleonard@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a1 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user sets SO_RESERVE_MEM socket option, in order to utilize the
reserved memory when in memory pressure state, we adjust rcv_ssthresh
according to the available reserved memory for the socket, instead of
using 4 * advmss always.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to track CE marks per rate sample (one round trip), TCP needs a
per-skb header field to record the tp->delivered_ce count when the skb
was sent. To make space, we replace the "last_in_flight" field which is
used exclusively for NV congestion control. The stat needed by NV can be
alternatively approximated by existing stats tcp_sock delivered and
mss_cache.
This patch counts the number of packets delivered which have CE marks in
the rate sample, using similar approach of delivery accounting.
Cc: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch the mentioned helper is
used only inside its compilation unit: let's make
it static.
RFC -> v1:
- preserve the tcp_build_frag() helper (Eric)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the tcp_skb_entail() helper is actually skb_entail(), renamed
to provide proper scope.
The two helper will be used by the next patch.
RFC -> v1:
- rename skb_entail to tcp_skb_entail (Eric)
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski