Small mods for setting up the uart - parity, flow control
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set the timeout and threshold to better values.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow hardware flow control to be set from an ioctl.
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch reduces the stack usage of the function serial_event() in
serial_cs from 2212 to 228. I used a patched version of gcc 3.4.3 on i386
with -fno-unit-at-a-time disabled.
This patch is only compile tested.
Acked-by: Randy Dunlap <rddunlap@osdl.org>
Signed-off-by: Yum Rayan <yum.rayan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Sascha Hauer
This patch adds UCFR_RFDIV setting into i.MX serial driver.
This is required, if loader does not fully agree with Linux kernel
about UART setup manner. Linux only blindly expected some values until
now. This should enable to use even serial ports not recognized by
boot-loader as for example third UART found in the bluethoot module.
Patch also enables to detect original setup baudrate in more cases.
Signed-off-by: Pavel Pisa
Signed-off-by: Sascha Hauer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert 8250_hp300 to use serial8250_register_port() and
serial8250_unregister_port().
Tested by Kars de Jong, 4/4/2005.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
We were forgetting to call sunsu_change_speed(). The reason
that replugging in the mouse cable "fixes things" is that
causes a BREAK interrupt which in turn caused a call to
sunsu_change_speed() which would get the chip setup properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the formatting of some comments in 8250.c, and add a note that the
register_serial / unregister_serial shouldn't be used in new code.
We do this here in preference to adding to linux/serial.h, since that is used
by a number of non-8250 drivers which pretend to be 8250. It is not known
whether it would be appropriate to do so.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- plug various leaks and use after frees in the remove and
initialization failure path (some still left)
- remove useless global list of boards and use pci_set_drvdata instead
- unobsfucate init path by merging functions together
- kill various totally useless state variables
- .. probably more I forgot
Note that the tty part still generates lots of sparse warnings and there's
still a totally useless layer of function pointer indirections, but maybe
someone else will fix that bit up.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
-rc2-mm1 still contains few places where u32 and pm_message_t. This fixes
drivers/serial [should change no code].
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Patrick Gefre