gdbserver inserting a breakpoint ends up calling copy_user_page() for a
code page. The generic version of which (non-aliasing config) didn't set
the PG_arch_1 bit hence update_mmu_cache() didn't sync dcache/icache for
corresponding dynamic loader code page - causing garbade to be executed.
So now aliasing versions of copy_user_highpage()/clear_page() are made
default. There is no significant overhead since all of special alias
handling code is compiled out for non-aliasing build
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The current code uses 2 bits for determining page's dcache color, thus
sorting pages into 4 bins, whereas the aliasing dcache really has 2 bins
(8k page, 64k dcache - 4 way-set-assoc).
This can cause extraneous flushes - e.g. color 0 and 2.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The VM_EXEC check in update_mmu_cache() was getting optimized away
because of a stupid error in definition of macro addr_not_cache_congruent()
The intention was to have the equivalent of following:
if (a || (1 ? b : 0))
but we ended up with following:
if (a || 1 ? b : 0)
And because precedence of '||' is more that that of '?', gcc was optimizing
away evaluation of <a>
Nasty Repercussions:
1. For non-aliasing configs it would mean some extraneous dcache flushes
for non-code pages if U/K mappings were not congruent.
2. For aliasing config, some needed dcache flush for code pages might
be missed if U/K mappings were congruent.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This manifested as grep failing psuedo-randomly:
-------------->8---------------------
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$ ip address show lo | grep inet
[ARCLinux]$
[ARCLinux]$ ip address show lo | grep inet
inet 127.0.0.1/8 scope host lo
-------------->8---------------------
ARC700 MMU provides fully orthogonal permission bits per page:
Ur, Uw, Ux, Kr, Kw, Kx
The user mode page permission templates used to have all Kernel mode
access bits enabled.
This caused a tricky race condition observed with uClibc buffered file
read and UNIX pipes.
1. Read access to an anon mapped page in libc .bss: write-protected
zero_page mapped: TLB Entry installed with Ur + K[rwx]
2. grep calls libc:getc() -> buffered read layer calls read(2) with the
internal read buffer in same .bss page.
The read() call is on STDIN which has been redirected to a pipe.
read(2) => sys_read() => pipe_read() => copy_to_user()
3. Since page has Kernel-write permission (despite being user-mode
write-protected), copy_to_user() suceeds w/o taking a MMU TLB-Miss
Exception (page-fault for ARC). core-MM is unaware that kernel
erroneously wrote to the reserved read-only zero-page (BUG #1)
4. Control returns to userspace which now does a write to same .bss page
Since Linux MM is not aware that page has been modified by kernel, it
simply reassigns a new writable zero-init page to mapping, loosing the
prior write by kernel - effectively zero'ing out the libc read buffer
under the hood - hence grep doesn't see right data (BUG #2)
The fix is to make all kernel-mode access permissions mirror the
user-mode ones. Note that the kernel still has full access to pages,
when accessed directly (w/o MMU) - this fix ensures that kernel-mode
access in copy_to_from() path uses the same faulting access model as for
pure user accesses to keep MM fully aware of page state.
The issue is peudo-random because it only shows up if the TLB entry
installed in #1 is present at the time of #3. If it is evicted out, due
to TLB pressure or some-such, then copy_to_user() does take a TLB Miss
Exception, with a routine write-to-anon COW processing installing a
fresh page for kernel writes and also usable as it is in userspace.
Further the issue was dormant for so long as it depends on where the
libc internal read buffer (in .bss) is mapped at runtime.
If it happens to reside in file-backed data mapping of libc (in the
page-aligned slack space trailing the file backed data), loader zero
padding the slack space, does the early cow page replacement, setting
things up at the very beginning itself.
With gcc 4.8 based builds, the libc buffer got pushed out to a real
anon mapping which triggers the issue.
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Flush and INVALIDATE the dcache page.
This helper is only used for writeback of CODE pages to memory. So
there's no value in keeping the dcache lines around. Infact it is risky
as a writeback on natural eviction under pressure can cause un-needed
writeback with weird issues on aliasing dcache configurations.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The TB10x platform port includes a custom mechanism using to set up
default pin controller configurations using abilis,simple-default
pin configurations of nodes compatible with abilis,simple-pinctrl. This
mechanism is redundant with the Linux standard "default" pin
configuration, see commit ab78029ecc
"drivers/pinctrl: grab default handles from device core".
This patch removes the TB10x custom mechanism in favour of the Linux
standard.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
I'm satisified with testing, specially with fuse which has historically given
grief to VIPT arches (ARM/PARISC...)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRjPVlAAoJEGnX8d3iisJeF60P/36JELOrdTOJB8GDn/i22yu4
zxFrroH4EpXCobe4JzrmhXU0vdMKmyhaRsdmQt2pV474LX1ajQeoRi6n7xuiYymr
p0H8/jde7ZDHGxJRP9OIuIIU57N+sVwQvrXvfnz/dc4c92MD9EWEwvoytnCVuKSx
k/YIQ5oDj6hFH13V68eXXs+KBrXyPiYO9UIWYmwRZv/0Bm6P1EpXQSMWzeCP0X/y
FHVEc4i92bIkqpOadUnhCBHGZqjkrhwFL2FCI35/12TgSwjPU1Q6IJCtH7Lg9ygI
oFqut5wN+dhkxlfiyvgTXErmnvhDOHLbMQJYC9svHin8TtfznQhJDAWYeSH/6Mde
/hE/bXV55ucdJ48ZT6JRvxHeJQgTAvbXDIIQYe/wAJEvXidWEo4Y/qRTIXP03Ixm
Ie69d9WSmUlx4FmYxBQodDQFK9slnc+0UfsWcCG+OrT0wwrKBRr3To2WYEFowQer
fpIk6/68+LiQK+IzFAhPtBppSgcQoEBsXAD/MDKsQcRk84W1nKPt6SiT/wCAzOZ7
ezTL1eSlfzWXNbtohdm8xN8frt/4fZLZTaZkqtnMPBi0iIC5DAsJy27YlBQDaRd/
Hzd0y6bJQDcsjjWmZuUkFZVbCyYlE0CIW6sbHC91i51egKReYHy7T6Ef/n+qn+ho
jxohq5/JvG+0Vha0Q2h6
=r4lw
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull second set of arc arch updates from Vineet Gupta:
"Aliasing VIPT dcache support for ARC
I'm satisified with testing, specially with fuse which has
historically given grief to VIPT arches (ARM/PARISC...)"
* tag 'arc-v3.10-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [TB10x] Remove GENERIC_GPIO
ARC: [mm] Aliasing VIPT dcache support 4/4
ARC: [mm] Aliasing VIPT dcache support 3/4
ARC: [mm] Aliasing VIPT dcache support 2/4
ARC: [mm] Aliasing VIPT dcache support 1/4
ARC: [mm] refactor the core (i|d)cache line ops loops
ARC: [mm] serious bug in vaddr based icache flush
* Support for two new platforms based on ARC700
- Abilis TB10x SoC [Chritisian/Pierrick]
- Simulator only System-C Model [Mischa]
* ARC specific MM improvements
- Avoid full TLB flush (ASID increment) on munmap (even single page)
- VIPT Cache Flushing improvements
+ Delayed dcache flush for non-aliasing dcache (big performance boost)
+ icache flush aliasing agnostic (no need to kill all possible aliases)
* Others
- Avoid needless rebuild of DTB files for every kernel build
- Remove builtin cmdline as that is already provided by DeviceTree/bootargs
- Fixing unaligned access emulation corner case
- checkpatch fixes [Sachin]
- Various fixlets [Noam]
- Minor build failures/cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDp
-----END PGP SIGNATURE-----
Merge tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC port updates from Vineet Gupta:
"Support for two new platforms based on ARC700:
- Abilis TB10x SoC [Chritisian/Pierrick]
- Simulator only System-C Model [Mischa]
ARC specific MM improvements:
- Avoid full TLB flush (ASID increment) on munmap (even single page)
- VIPT Cache Flushing improvements
+ Delayed dcache flush for non-aliasing dcache (big performance boost)
+ icache flush aliasing agnostic (no need to kill all possible aliases)
Others:
- Avoid needless rebuild of DTB files for every kernel build
- Remove builtin cmdline as that is already provided by DeviceTree/bootargs
- Fixing unaligned access emulation corner case
- checkpatch fixes [Sachin]
- Various fixlets [Noam]
- Minor build failures/cleanups"
* tag 'arc-v3.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc: (35 commits)
ARC: [mm] Lazy D-cache flush (non aliasing VIPT)
ARC: [mm] micro-optimize page size icache invalidate
ARC: [mm] remove the pessimistic all-alias-invalidate icache helpers
ARC: [mm] consolidate icache/dcache sync code
ARC: [mm] optimise icache flush for kernel mappings
ARC: [mm] optimise icache flush for user mappings
ARC: [mm] optimize needless full mm TLB flush on munmap
ARC: Add support for nSIM OSCI System C model
ARC: [TB10x] Adapt device tree to new compatible string
ARC: [TB10x] Add support for TB10x platform
ARC: [TB10x] Device tree of TB100 and TB101 Development Kits
ARC: Prepare interrupt code for external controllers
ARC: Allow embedded arc-intc to be properly placed in DT intc hierarchy
ARC: [cmdline] Don't overwrite u-boot provided bootargs
ARC: [cmdline] Remove CONFIG_CMDLINE
ARC: [plat-arcfpga] defconfig update
ARC: unaligned access emulation broken if callee-reg dest of LD/ST
ARC: unaligned access emulation error handling consolidation
ARC: Debug/crash-printing Improvements
ARC: fix typo with clock speed
...
This is the meat of the series which prevents any dcache alias creation
by always keeping the U and K mapping of a page congruent.
If a mapping already exists, and other tries to access the page, prev
one is flushed to physical page (wback+inv)
Essentially flush_dcache_page()/copy_user_highpage() create K-mapping
of a page, but try to defer flushing, unless U-mapping exist.
When page is actually mapped to userspace, update_mmu_cache() flushes
the K-mapping (in certain cases this can be optimised out)
Additonally flush_cache_mm(), flush_cache_range(), flush_cache_page()
handle the puring of stale userspace mappings on exit/munmap...
flush_anon_page() handles the existing U-mapping for anon page before
kernel reads it via the GUP path.
Note that while not complete, this is enough to boot a simple
dynamically linked Busybox based rootfs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This preps the low level dcache flush helpers to take vaddr argument in
addition to the existing paddr to properly flush the VIPT dcache
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Nothing semantical
* simplify the alignement code by using & operation only
* rename variables clearly as paddr
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
vaddr used to index the cache was clipped from the wrong end, and thus
would potentially fail to flush the correct lines.
The problem was dorment for so long because up until the recent
optimizations it was only used for ptrace break-point only flushes.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
flush_dcache_page( ) is MM hook to ensure that a page has consistent
views between kernel and userspace. Thus it is called when
* kernel writes to a page which at some later point could get mapped to
userspace (so kernel mapping needs to be flushed-n-inv)
* kernel is about to read from a page with possible userspace mappings
(so userspace mappings needs to be made coherent with kernel ones)
However for Non aliasing VIPT dcache, any userspace mapping will always
be congruent to kernel mapping. Thus d-cache need need not be flushed at
all (or delayed indefinitely).
The only reason it does need to be flushed is when mapping code pages.
Since icache doesn't snoop dcache, those dirty dcache lines need to be
written back to memory and icache line invalidated so that icache lines
fetch will get the right data.
Decent gains on LMBench fork/exec/sh and File I/O micro-benchmarks.
(1) FPGA @ 80 MHZ
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.9-rc6-a Linux 3.9.0-r 80 4.79 8.72 66.7 116. 239. 8.39 30.4 4798 14.K 34.K
3.9-rc6-b Linux 3.9.0-r 80 4.79 8.62 65.4 111. 239. 8.35 29.0 3995 12.K 30.K
3.9-rc7-c Linux 3.9.0-r 80 4.79 9.00 66.1 106. 239. 8.61 30.4 2858 10.K 24.K
^^^^ ^^^^ ^^^
File & VM system latencies in microseconds - smaller is better
-------------------------------------------------------------------------------
Host OS 0K File 10K File Mmap Prot Page 100fd
Create Delete Create Delete Latency Fault Fault selct
--------- ------------- ------ ------ ------ ------ ------- ----- ------- -----
3.9-rc6-a Linux 3.9.0-r 317.8 204.2 1122.3 375.1 3522.0 4.288 20.7 126.8
3.9-rc6-b Linux 3.9.0-r 298.7 223.0 1141.6 367.8 3531.0 4.866 20.9 126.4
3.9-rc7-c Linux 3.9.0-r 278.4 179.2 862.1 339.3 3705.0 3.223 20.3 126.6
^^^^^ ^^^^^ ^^^^^ ^^^^
(2) Customer Silicon @ 500 MHz (166 MHz mem)
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
abilis-ba Linux 3.9.0-r 497 0.71 1.38 4.58 12.0 35.5 1.40 3.89 2070 5525 13.K
abilis-ca Linux 3.9.0-r 497 0.71 1.40 4.61 11.8 35.6 1.37 3.92 1411 4317 10.K
^^^^ ^^^^ ^^^
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
start address is already page aligned and size is const PAGE_SIZE,
thus fixups for alignment not needed in generated code.
bloat-o-meter vmlinux-mm5 vmlinux
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-32 (-32)
function old new delta
__inv_icache_page 82 50 -32
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Now that we have same helper used for all icache invalidates (i.e.
vaddr+paddr based exact line invalidate), consolidate the open coded
calls into one place.
Also rename flush_icache_range_vaddr => __sync_icache_dcache
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This change continues the theme from prev commit - this time icache
handling for kernel's own code modification (vmalloc: loadable modules,
breakpoints for kprobes/kgdb...)
flush_icache_range() calls the CDU icache helper with vaddr to enable
exact line invalidate.
For a true kernel-virtual mapping, the vaddr is actually virtual hence
valid as index into cache. For kprobes breakpoint however, the vaddr arg
is actually paddr - since that's how normal kernel is mapped in ARC
memory map. This implies that CDU will use the same addr for
indexing as for tag match - which is fine since kernel code would only
have that "implicit" mapping and none other.
This should speed up module loading significantly - specially on default
ARC700 icache configurations (32k) which alias.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC icache doesn't snoop dcache thus executable pages need to be made
coherent before mapping into userspace in flush_icache_page().
However ARC700 CDU (hardware cache flush module) requires both vaddr
(index in cache) as well as paddr (tag match) to correctly identify a
line in the VIPT cache. A typical ARC700 SoC has aliasing icache, thus
the paddr only based flush_icache_page() API couldn't be implemented
efficiently. It had to loop thru all possible alias indexes and perform
the invalidate operation (ofcourse the cache op would only succeed at
the index(es) where tag matches - typically only 1, but the cost of
visiting all the cache-bins needs to paid nevertheless).
Turns out however that the vaddr (along with paddr) is available in
update_mmu_cache() hence better suits ARC icache flush semantics.
With both vaddr+paddr, exactly one flush operation per line is done.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
munmap ends up calling tlb_flush() which for ARC was flushing the entire
TLB unconditionally (by moving the MMU to a new ASID)
do_munmap
unmap_region
unmap_vmas
unmap_single_vma
unmap_page_range
tlb_start_vma
zap_pud_range
tlb_end_vma()
tlb_finish_mmu
tlb_flush() ---> unconditional flush_tlb_mm()
So even a single page munmap, a frequent operation when uClibc dynamic
linker (ldso) is loading the dependent shared libraries, would move the
the ASID multiple times - needlessly invalidating the pre-faulted TLB
entries (and increasing the rate of ASID wraparound + full TLB flush).
This is now optimised to only be called if tlb->full_mm (which means
for exit/execve) cases only. And for those cases, flush_tlb_mm() is
already optimised to be a no-op for mm->mm_users == 0.
So essentially there are no mmore full mm flushes - except for fork which
anyhow needs it for properly COW'ing parent address space.
munmap now needs to do TLB range flush, which is implemented with
tlb_end_vma()
Results
-------
1. ASID now consistenly moves by 4 during a simple ls (as opposed to 5 or
7 before).
2. LMBench microbenchmark also shows improvements
Basic system parameters
------------------------------------------------------------------------------
Host OS Description Mhz tlb cache mem scal
pages line par load
bytes
--------- ------------- ----------------------- ---- ----- ----- ------ ----
3.9-rc5-0 Linux 3.9.0-r 3.9-rc5-0404-gcc-4.4-ba 80 8 64 1.1000 1
3.9-rc5-0 Linux 3.9.0-r 3.9-rc5-0405-avoid-full 80 8 64 1.1200 1
Processor, Processes - times in microseconds - smaller is better
------------------------------------------------------------------------------
Host OS Mhz null null open slct sig sig fork exec sh
call I/O stat clos TCP inst hndl proc proc proc
--------- ------------- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ----
3.9-rc5-0 Linux 3.9.0-r 80 4.81 8.69 68.6 118. 239. 8.53 31.6 4839 13.K 34.K
3.9-rc5-0 Linux 3.9.0-r 80 4.46 8.36 53.8 91.3 223. 8.12 24.2 4725 13.K 33.K
File & VM system latencies in microseconds - smaller is better
-------------------------------------------------------------------------------
Host OS 0K File 10K File Mmap Prot Page 100fd
Create Delete Create Delete Latency Fault Fault selct
--------- ------------- ------ ------ ------ ------ ------- ----- ------- -----
3.9-rc5-0 Linux 3.9.0-r 314.7 223.2 1054.9 390.2 3615.0 1.590 20.1 126.6
3.9-rc5-0 Linux 3.9.0-r 265.8 183.8 1014.2 314.1 3193.0 6.910 18.8 110.4
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This adds support for an ARC Virtual Platform. This platform is based on the
System C standard promoted by the OSCI (Open System C Initiative) and uses
nSIM to simulate the ARC CPU core itself.
Users can build a virtual SoC by combining System C models of peripherals
and CPU cores.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The original device tree was written using a slightly different
implementation of the fixed-factor-clock device tree binding. The
compatible string must be modified in order to be compatible with the
new implementation.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Infrastructure required to make the Linux kernel compile and boot on the
Abilis Systems TB10x series of SOCs based on ARC700 CPUs:
- Kmake related files (Kconfig, Makefile, tb10x_defconfig)
- TB10x platform initialisation
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
These are the device tree files for the Abilis Systems TB100 and TB101 ICs and
their respective development kit PCBs. These files are committed in preparation
of the following patch set which adds support for these chips to the ARC
platform.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch adds some room for CPU-external interrupt controllers in the
Linux interrupt space. Until now, only the 32 CPU internal interrupt lines
were supported which does not allow for external interrupt controllers such
as GPIO modules etc.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arc-intc is initialized in arc common code as it is applicable to all
platforms. However platforms with their own external intc still need to
refer to it for correct DT interrupt tree hierarchy setup,
e.g.
static struct of_device_id __initdata tb10x_irq_ids[] = {
{ .compatible = "snps,arc700-intc", .data = dummy_init_irq },
{ .compatible = "abilis,tb10x_ictl", .data = tb10x_init_irq },
{},
};
The fix is to use the generic irqchip framework to tie all irqchips in
a special linker section and then call irqchip_init() which calls the
DT of_irq_init() for all the intc in one go.
That way the platform code need not be aware of arc-intc at all.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The existing code was wrong on several counts:
* uboot provided bootargs were copied into @boot_command_line, only to
be over-written by setup_machine_fdt(), effectively lost
* @cmdline_p returned by setup_arch() to start_kernel() didn't include
the DT /bootargs
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Given that DeviceTree /bootargs can provide similar functionality,
no point in providing duplicate infrastructure.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The fixup code correctly updates the callee-regs on stack, but
fails to unwind it into actual register file. Thus userspace won't see
the update.
Reported-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
If CONFIG_ARC_MISALIGN_ACCESS is not enabled, or if the fixup fails,
call the same error handler: same signal/si_code to user (SIGBUS)
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
* Remove the line-break between scratch/callee-regs (sneaked in when we
converted from printk to pr_*
* Use %pS to print the symbol names of faulting PC (ret pseudo register)
and BLINK (call return register)
* Don't print user-vma for a kernel crash (only do it for
print-fatal-signals based regfile dump)
* Verbose print the Interrupt/Exception Enable/Active state
* for main executable link address is 0x10000 based (vs. 0) thus offset
of faulting PC needs to be adjusted
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This tracks mainline commit ae903caae2 "Bury the conditionals from
kernel_thread/kernel_execve series" which we missed out as ARC port was
not yet mainline.
[vgupta: commit log modified]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both dump_stack() and show_stack() are currently implemented by each
architecture. show_stack(NULL, NULL) dumps the backtrace for the
current task as does dump_stack(). On some archs, dump_stack() prints
extra information - pid, utsname and so on - in addition to the
backtrace while the two are identical on other archs.
The usages in arch-independent code of the two functions indicate
show_stack(NULL, NULL) should print out bare backtrace while
dump_stack() is used for debugging purposes when something went wrong,
so it does make sense to print additional information on the task which
triggered dump_stack().
There's no reason to require archs to implement two separate but mostly
identical functions. It leads to unnecessary subtle information.
This patch expands the dummy fallback dump_stack() implementation in
lib/dump_stack.c such that it prints out debug information (taken from
x86) and invokes show_stack(NULL, NULL) and drops arch-specific
dump_stack() implementations in all archs except blackfin. Blackfin's
dump_stack() does something wonky that I don't understand.
Debug information can be printed separately by calling
dump_stack_print_info() so that arch-specific dump_stack()
implementation can still emit the same debug information. This is used
in blackfin.
This patch brings the following behavior changes.
* On some archs, an extra level in backtrace for show_stack() could be
printed. This is because the top frame was determined in
dump_stack() on those archs while generic dump_stack() can't do that
reliably. It can be compensated by inlining dump_stack() but not
sure whether that'd be necessary.
* Most archs didn't use to print debug info on dump_stack(). They do
now.
An example WARN dump follows.
WARNING: at kernel/workqueue.c:4841 init_workqueues+0x35/0x505()
Hardware name: empty
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #9
0000000000000009 ffff88007c861e08 ffffffff81c614dc ffff88007c861e48
ffffffff8108f50f ffffffff82228240 0000000000000040 ffffffff8234a03c
0000000000000000 0000000000000000 0000000000000000 ffff88007c861e58
Call Trace:
[<ffffffff81c614dc>] dump_stack+0x19/0x1b
[<ffffffff8108f50f>] warn_slowpath_common+0x7f/0xc0
[<ffffffff8108f56a>] warn_slowpath_null+0x1a/0x20
[<ffffffff8234a071>] init_workqueues+0x35/0x505
...
v2: CPU number added to the generic debug info as requested by s390
folks and dropped the s390 specific dump_stack(). This loses %ksp
from the debug message which the maintainers think isn't important
enough to keep the s390-specific dump_stack() implementation.
dump_stack_print_info() is moved to kernel/printk.c from
lib/dump_stack.c. Because linkage is per objecct file,
dump_stack_print_info() living in the same lib file as generic
dump_stack() means that archs which implement custom dump_stack()
- at this point, only blackfin - can't use dump_stack_print_info()
as that will bring in the generic version of dump_stack() too. v1
The v1 patch broke build on blackfin due to this issue. The build
breakage was reported by Fengguang Wu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390 bits]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull SMP/hotplug changes from Ingo Molnar:
"This is a pretty large, multi-arch series unifying and generalizing
the various disjunct pieces of idle routines that architectures have
historically copied from each other and have grown in random, wildly
inconsistent and sometimes buggy directions:
101 files changed, 455 insertions(+), 1328 deletions(-)
this went through a number of review and test iterations before it was
committed, it was tested on various architectures, was exposed to
linux-next for quite some time - nevertheless it might cause problems
on architectures that don't read the mailing lists and don't regularly
test linux-next.
This cat herding excercise was motivated by the -rt kernel, and was
brought to you by Thomas "the Whip" Gleixner."
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
idle: Remove GENERIC_IDLE_LOOP config switch
um: Use generic idle loop
ia64: Make sure interrupts enabled when we "safe_halt()"
sparc: Use generic idle loop
idle: Remove unused ARCH_HAS_DEFAULT_IDLE
bfin: Fix typo in arch_cpu_idle()
xtensa: Use generic idle loop
x86: Use generic idle loop
unicore: Use generic idle loop
tile: Use generic idle loop
tile: Enter idle with preemption disabled
sh: Use generic idle loop
score: Use generic idle loop
s390: Use generic idle loop
powerpc: Use generic idle loop
parisc: Use generic idle loop
openrisc: Use generic idle loop
mn10300: Use generic idle loop
mips: Use generic idle loop
microblaze: Use generic idle loop
...
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, for every ARC kernel build I see the following:
--------------->8-----------------
DTB arch/arc/boot/dts/angel4.dtb.S
AS arch/arc/boot/dts/angel4.dtb.o
LD arch/arc/boot/dts/built-in.o
rm arch/arc/boot/dts/angel4.dtb.S <-- forces rebuild next iter
CHK kernel/config_data.h
--------------->8-----------------
This is because *.dts.S is intermediate file in dtb generation and is by
default deleted by make which needs a ".SECONDARY" hint to NOT do so.
This could have ideally been done in scripts/Makefile.lib - for benefit
of all, however .SECONDARY doesn't seem to work with wildcards.
Thanks to Stephen for suggesting .SECONDARY (vs .PRECIOUS) and making
that work using a non wildcard version in arch makefile.
Thanks to James Hogan for pointing out that *.dtb.S now needs to be
added to clean-files
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
commit "fs: make binfmt support for #! scripts modular and removable"
made support for #!scripts optional - thus need to include the Kconfig
file to get all relevant BINFMT_*
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Currently ARC_HAS_LLSC can be influenced by platform for SMP only using
ARC_HAS_COH_LLSC. For !SMP it defaults to "y".
It turns out that some customers can't support it all, even in UP.
So we change the semantics, and use a negative dependency ARC_CANT_LLSC.
Any platform (independent of SMP or !SMP) can select it to disable LLSC.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
arch/arc/kernel/traps.c no longer compiles without explicitly including
asm/kprobes.h
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The existing uImage target always generates gzip compressed image which
drags bootup for some very slow FPGA customer boards.
So introduce seperate make targets:uImage.{bin,gz} with uncompressed
being default. Also tie gz generation to CONFIG_KERNEL_GZIP, which a
platform can select in it's Kconfig if it wishes gz to be default.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Vineet Gupta