The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the following sparse warning:
drivers/dma/mxs-dma.c:696:17: warning: symbol 'mxs_dma_xlate' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for returning the residue for current transfer cookie by
reading the transfered buffer size(BTSIZE) in CTRLA register.
For a single buffer cookie, the descriptor length minus BTSIZE
can get the residue.
For a lli cookie, remain_desc will record remain descriptor length
when last descriptor finish, the remain_desc minus BTSIZE can get the
current residue.
If the cookie has completed successfully, the residue will be zero.
If the cookie is in progress, it will be the number of bytes yet to be transferred.
If get residue error, the cookie will be turn into error status.
Check dma fifo to see if data remain, let issue pending finish remain work if there is.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In one dma transfer, the data transfer width can be configured and it is limited by source or destination peripheral width,
tx_width will save the transfer width, but for memcpy, either source or destination transfer width is taken as tx_width.
Signed-off-by: Elen Song <elen.song@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
No modification in CFG register configuration, just rearrange
bits directives to group logically and make it more readable.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Peripheral handshaking identification numbers can be bigger than 15, so new
fields have been created in the CFG register.
Add macros to take this modification into account and use them in
at_dma_xlate() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
imxdma->dev is used for dev_warn before it was set.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding devicetree support for imx-dma driver. Use driver name for
function 'imx_dma_is_general_purpose' because the devicename for
devicetree initialized devices is different.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merge first patch-bomb from Andrew Morton:
- various misc bits
- I'm been patchmonkeying ocfs2 for a while, as Joel and Mark have been
distracted. There has been quite a bit of activity.
- About half the MM queue
- Some backlight bits
- Various lib/ updates
- checkpatch updates
- zillions more little rtc patches
- ptrace
- signals
- exec
- procfs
- rapidio
- nbd
- aoe
- pps
- memstick
- tools/testing/selftests updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (445 commits)
tools/testing/selftests: don't assume the x bit is set on scripts
selftests: add .gitignore for kcmp
selftests: fix clean target in kcmp Makefile
selftests: add .gitignore for vm
selftests: add hugetlbfstest
self-test: fix make clean
selftests: exit 1 on failure
kernel/resource.c: remove the unneeded assignment in function __find_resource
aio: fix wrong comment in aio_complete()
drivers/w1/slaves/w1_ds2408.c: add magic sequence to disable P0 test mode
drivers/memstick/host/r592.c: convert to module_pci_driver
drivers/memstick/host/jmb38x_ms: convert to module_pci_driver
pps-gpio: add device-tree binding and support
drivers/pps/clients/pps-gpio.c: convert to module_platform_driver
drivers/pps/clients/pps-gpio.c: convert to devm_* helpers
drivers/parport/share.c: use kzalloc
Documentation/accounting/getdelays.c: avoid strncpy in accounting tool
aoe: update internal version number to v83
aoe: update copyright date
aoe: perform I/O completions in parallel
...
There have never been any real users of MEMSET operations since they
have been introduced in January 2007 by commit 7405f74bad ("dmaengine:
refactor dmaengine around dma_async_tx_descriptor"). Therefore remove
support for them for now, it can be always brought back when needed.
[sebastian.hesselbarth@gmail.com: fix drivers/dma/mv_xor]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Olof Johansson <olof@lixom.net>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
- Fix various error path and sparse bugs in the DMA40 driver
- Fix various compile errors in the ux500 crypto driver
(dependent on the DMA40 changes).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=sHkJ
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
DMA40 fixes for earlier submitted driver patches:
- Fix various error path and sparse bugs in the DMA40 driver
- Fix various compile errors in the ux500 crypto driver
(dependent on the DMA40 changes).
* tag 'ux500-dma40-for-arm-soc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
dmaengine: ste_dma40: fix error return code in d40_probe()
Signed-off-by: Olof Johansson <olof@lixom.net>
--------------------------------------
This pull request adds DT and runtime PM to
EDMA ARM private API so it can be used on
DT enabled DaVinci and OMAP platforms.
Also adds DMA channel crossbar mapping
support to be used by DT-enabled platforms
which use it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=h9EO
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC updates for v3.11 - part 2
This pull request adds DT and runtime PM to
EDMA ARM private API so it can be used on
DT enabled DaVinci and OMAP platforms.
Also adds DMA channel crossbar mapping
support to be used by DT-enabled platforms
which use it.
* tag 'davinci-for-v3.11/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
ARM: edma: Convert to devm_* api
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix sparse warnings:
drivers/dma/ste_dma40.c:81:26: warning: symbol 'dma40_memcpy_conf_phy' was not declared. Should it be static?
drivers/dma/ste_dma40.c:95:26: warning: symbol 'dma40_memcpy_conf_log' was not declared. Should it be static?
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable TI EDMA option on OMAP and TI_PRIV_EDMA
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=BH9M
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
From Sekhar Nori:
DaVinci SoC changes for v3.11
This pull request moves DaVinci EDMA library to
arch/arm/common so it can be used by OMAP based AM335x.
This is a temporary step until all drivers are converted
to use the dmaengine driver in drivers/dma/edma.c.
Several drivers like SPI, MMC/SD have already been converted.
Some like audio are pending.
The other two patches in the pull request are cleanup in nature.
* tag 'davinci-for-v3.11/soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: edma: remove unused transfer controller handlers
ARM: davinci: move private EDMA API to arm/common
ARM: davinci: remove __init atrribute from function declaration
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRvvkdAAoJEEEQszewGV1zqjQQAMFYxb4B0c2YweNzDzWjuWM/
STZNyAV62LcE7GvssFYpeJ/+lrB7tNwgplJQ13uluEdFws2Xd63G+qIVznkBE7rW
+ZLHG+MPi/uia2yYcg9Vz1M42Aj5COuu1q6ex9OfR2v/tX3G2G/rjIzAaiiEvWWd
ljcBGlDh41iphY6dsBtFFXR0b9rzzyhhmY5wS1P+bMyl9YlqYp0x0oznLo5eFTlA
9ad9H0oeYYXCcB0V5UI1wsRGCaJqa04xotb6uqn1TUPpVc9ZpYQUkVI/1Fb3gVez
3MrLW2/9tDfXWUOTZTo9VtC4rpbmGSsvBc3C0IUGEj9ovmWTCA/OU/WXsEOAymb9
+F36wMX07z8OmmebBn06s6/Zhy0ht9BoV+NeW4lz3s3uiuE3vxnaxW/kb845xfUI
7o87kV8DpXuEokNP+jYyCDJTw/feq5Dy0HXr4KFOAwXMd3imRREnHgvihCsFtNj4
vRkz+6A17YrtpuvCqnuXiM5Ts+Dz4MAEJ/Iokrm1e28fUw/wuklAXeII8+kxc36R
w6AHTbXpWPjglVAn3DTuh4BjIoN53/cLhttezg7NcgtgRW3AxyHGx3T+345mHsgT
dbust8Qow/bapby8NPHKJDHM5A9RGNWX4rJ+abTxI0iJ0fpcEWT1c5TKlpUR+0KZ
qMTNGvDfonu1xaoPLo81
=fstd
-----END PGP SIGNATURE-----
Merge tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds support for probing the COH 901 318 DMA controller
and channels from the device tree.
Contains portions of a sketch patch from Arnd Bergmann.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
support for the DMA40. Now with MUSB and some platform
data removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=rn7t
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
Second set of DMA40 changes: refactorings and device tree
support for the DMA40. Now with MUSB and some platform
data removal.
* tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dmaengine: ste_dma40: Fetch disabled channels from DT
dmaengine: ste_dma40: Fetch the number of physical channels from DT
ARM: ux500: Stop passing DMA platform data though AUXDATA
dmaengine: ste_dma40: Allow memcpy channels to be configured from DT
dmaengine: ste_dma40_ll: Replace meaningless register set with comment
dmaengine: ste_dma40: Convert data_width from register bit format to value
dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove recently unused stedma40_xfer_dir enums
dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one
dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove empty function u8500_of_init_devices()
ARM: ux500: Remove ux500-musb platform registation when booting with DT
usb: musb: ux500: add device tree probing support
usb: musb: ux500: attempt to find channels by name before using pdata
usb: musb: ux500: harden checks for platform data
usb: musb: ux500: take the dma_mask from coherent_dma_mask
usb: musb: ux500: move the MUSB HDRC configuration into the driver
usb: musb: ux500: move channel number knowledge into the driver
Both of_dma_nbcells field of the of_dma_controller and the args_count field of
the dma_spec are initialized by parsing the #dma-cells attribute of their device
tree node. So if the device tree nodes of a DMA controller and the dma_spec
match this means that of_dma_nbcells and args_count will also match. So the
second test in the of_dma_find_controller loop is redundant because given the
first test yields true the second test will also yield true. So we can safely
remove the test whether of_dma_nbcells matches args_count. Since this was the
last user of the of_dma_nbcells field we can remove it altogether.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no sensible reason why #dma-cells shouldn't be allowed to be 0. It is
completely up to the DMA controller how many additional parameters, besides the
phandle, it needs to identify a channel. E.g. for DMA controller with only one
channel or for DMA controllers which don't have a restriction on which channel
can be used for which peripheral it completely legitimate to not require any
additional parameters.
Also fixes the following warning:
drivers/dma/of-dma.c: In function 'of_dma_controller_register':
drivers/dma/of-dma.c:67:7: warning: 'nbcells' may be used uninitialized in this function
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When user interrupts ongoing transfers the dmatest may end up with console
lockup, oops, or data mismatch. This patch prevents user to abort any ongoing
test.
Documentation is updated accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Will Deacon <will.deacon@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In many of the error handling case, the return value 'ret' not set
and 0 will be return from d40_probe() even if error, but we should
return a negative error code instead in those error handling case.
This patch fixed them, and also removed useless variable 'err'.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms have channels which are not available for normal use.
This information is currently passed though platform data in internal
BSP kernels. Once those platforms land, they'll need to configure them
appropriately, so we may as well add the infrastructure.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms insist on obscure physical channel availability. This
information is currently passed though platform data in internal BSP
kernels. Once those platforms land, they'll need to configure them
appropriately, so we may as well add the infrastructure.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this moment in time the memcpy channels which can be used by the D40
are fixed, as each supported platform in Mainline uses the same ones.
However, platforms do exist which don't follow this convention, so
these will need to be tailored. Fortunately, these platforms will be DT
only, so this change has very little impact on platform data.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unsure of the author's intentions, rather than just removing the nop,
we're replacing it with a comment containing the possible intention
of the statement OR:ing with 0.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a DMA client requests and configures a DMA channel, it requests
data_width in Bytes. The DMA40 driver then swiftly converts it over to
the necessary register bit value. Unfortunately, for any subsequent
calculations we have to shift '1' by the bit pattern (1 << data_width)
times to make any sense of it.
This patch flips the semantics on its head and only converts the value
to its respective register bit pattern when writing to registers. This
way we can use the true data_width (in Bytes) value.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The aim is to make the code that little more readable.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STEDMA40_*_TO_* direction definitions are identical in all but name to
the pre-defined generic DMA_*_TO_* ones. Let's make things easy by not
duplicating such things.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The aim is to make the code that little more readable.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The "runtime idle" helper routine, rpm_idle(), currently ignores
return values from .runtime_idle() callbacks executed by it.
However, it turns out that many subsystems use
pm_generic_runtime_idle() which checks the return value of the
driver's callback and executes pm_runtime_suspend() for the device
unless that value is not 0. If that logic is moved to rpm_idle()
instead, pm_generic_runtime_idle() can be dropped and its users
will not need any .runtime_idle() callbacks any more.
Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle()
routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and
ata_port_runtime_idle(), respectively, as well as a few drivers'
ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has
been returned by the .runtime_idle() callback executed by it.
To reduce overall code bloat, make the changes described above.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
the ux500 to fetch DMA channels from the device tree:
- Full DT support and channel mapping in the DMA40 driver
- Dropping of platform data for migrated devices on the DT
boot path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=RTiI
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
This is a set of patches from Lee Jones to start converting
the ux500 to fetch DMA channels from the device tree:
- Full DT support and channel mapping in the DMA40 driver
- Dropping of platform data for migrated devices on the DT
boot path.
* tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (36 commits)
ARM: ux500: Register Cryp and Hash platform drivers on Snowball
crypto: ux500/[cryp|hash] - Show successful start-up in the bootlog
ARM: ux500: Stop passing Cryp DMA channel config information though pdata
crypto: ux500/cryp - Set DMA configuration though dma_slave_config()
crypto: ux500/cryp - Prepare clock before enabling it
ARM: ux500: Stop passing Hash DMA channel config information though pdata
crypto: ux500/hash - Set DMA configuration though dma_slave_config()
crypto: ux500/hash - Prepare clock before enabling it
ARM: ux500: Remove unnecessary attributes from DMA channel request pdata
dmaengine: ste_dma40: Correct copy/paste error
ARM: ux500: Remove DMA address look-up table
dmaengine: ste_dma40: Remove redundant address fetching function
dmaengine: ste_dma40: Only use addresses passed as configuration information
ARM: ux500: Stop passing UART's platform data for Device Tree boots
dmaengine: ste_dma40: Don't configure runtime configurable setup during allocate
dmaengine: ste_dma40: Remove unnecessary call to d40_phy_cfg()
dmaengine: ste_dma40: Separate Logical Global Interrupt Mask (GIM) unmasking
ARM: ux500: Pass remnant platform data though to DMA40 driver
dmaengine: ste_dma40: Supply full Device Tree parsing support
dmaengine: ste_dma40: Allow driver to be probe()able when DT is enabled
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The pm runtime reference counting of the driver is broken for the case
when there is more than one transfer queued, leading to the device being
runtime suspend while active. Fix it.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
Addresses are now stored in local data structures and are easy to
obtain, thus a specialist function used to fetch them is now surplus
to requirement.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Addresses are passed in from the client's driver via the invocation of
dmaengine_slave_config(), so there's no need to fetch them from platform
data too, hardwired or otherwise. This is a great step forward, as it
elevates a large burden from platform data in the way of a look-up
table.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the dmaengine API for slave transfers, allocating and configuring
a channel are two separate actions. Here we're removing logical channel
configuration from the channel allocation routine for slave transfers,
as the same config is already done in the runtime config function, and
put the corresponding call into d40_config_memcpy() for the memcpy
code path.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Edited the commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The majority of configuration done in d40_phy_config() pertains
to physical channels. Move the call over to runtime config which
has different code paths for physical and logical channels already,
and make it an exclusive physical channel config function as the
name implies, and drop the is_log argument.
Since we moved the call to runtime_config() it only gets called
for device transfers, so encode the small snippet of configuration
pertaining to memcpy channels into the d40_config_memcpy()
function.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[rewrote the commit message]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During the initial setup of a logical channel, it is necessary to unmask
the GIM in order to receive generated terminal count and error interrupts.
We're separating out this required code so it will be possible to move
the remaining code in d40_phy_cfg(), which is mostly runtime configuration
into the runtime_config() routine.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the new DMA DT bindings and API, we can register the DMA40 driver
as Device Tree capable. Now, when a client attempts to allocate a
channel using the DMA DT bindings via its own node, we are able to parse
the request and allocate a channel in the correct manner.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Acked-by: Vinod Koul <vinod.koul@intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When booting using Device Tree, devices aren't registered in the normal
way. Instead, they need to be provided with a compatible string which is
held in an OF Match Table for comparison during start-up. Here we provide
the compatible string and prepare the driver to not receive a platform
data pointer.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Fixed up whitespace error]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's the way that most other drivers do it.
Very trivial clean-up which reduces line count and simplifies code.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now we know the total of physical and logical channels, we may as
well report them within the information log.
Before:
dma40 dma40.0: hardware revision: 3 @ 0x801c0000 with 8 physical channels
After:
<as above ...> and 256 logical channels
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At the moment we fetch the hardware revision, then do some stuff, then
check whether the revision is correct and return in error if it's not.
Well we may as well check it as soon as we know what it is, so let's
move the check right up underneath where we acquire the version.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Before allocating memory for logical channels, the current driver
checks to see if there are any. Well as the dma40_memcpy_channels[]
array is always populated, the check is always true. Best to
remove the check.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change will cost ~25KB of memory, but it's worth the trade-off,
as it removes a great deal of overhead. It means that instead of only
allocating memory for the logical channels in use, it does so for all
available ones, which is 32 per physical channel. However, this now
means we can remove some platform data and we don't have to worry
about adding vendor specific variables to Device Tree.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current implementation of the DMA40's local MAX() macro evaluates
its arguments more times than is necessary and it not type checked.
This patch strips replaces it with a new, more efficient constant.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices which utilise DMA use the same device numbers for transmitting
and receiving. In this patch we encode the source and destination
information into one single attribute. We can subsequently exploit the
direction attribute to see which of the transfer directions are being
described. This also lessens the burden on platform data.
Cc: Dan Williams <djbw@fb.com>
Cc: Per Forlin <per.forlin@stericsson.com>
Cc: Rabin Vincent <rabin@rab.in>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If we compare an event's group (dev_type / 16) with STEDMA40_DEV_DST_MEMORY
(-1), the only way we'd obtain a positive result is if we passed -16 as a
device type, which is unfeasible. Instead, it would be much more sane to
compare STEDMA40_DEV_DST_MEMORY against the raw dev_type in order to expect
the expected result.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are only two default memcpy configurations used for the DMA40
driver; one for physical memcpy and one for logical memcpy. Instead
of invariably passing the same configurations though platform data,
we're moving them into the driver instead.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit
"dmaengine: ste_dma40: Assign memcpy channels in the driver"
had two problems:
- It assigned magic numbers to the memcpy event lines
instead of giving them symbolic names.
- It seems to have missed one of the memcpy event lines,
number 51.
This patch fixes it up.
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The channels reserved for memcpy are the same for all currently
supported platforms. With this in mind, we can ease the platform
data passing requirement by moving these assignments out from
platform code and place them directly into the driver.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Since we have CSRT only to get additional DMA controller resources, let's get
rid of drivers/acpi/csrt.c and move its logic inside ACPI DMA helpers code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dmaengine updates from Vinod Koul:
"This time we have dmatest improvements from Andy along with dw_dmac
fixes. He has also done support for acpi for dmanegine.
Also we have bunch of fixes going in DT support for dmanegine for
various folks. Then Haswell and other ioat changes from Dave and
SUDMAC support from Shimoda."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
dma: tegra: implement suspend/resume callbacks
dma:of: Use a mutex to protect the of_dma_list
dma: of: Fix of_node reference leak
dmaengine: sirf: move driver init from module_init to subsys_initcall
sudmac: add support for SUDMAC
dma: sh: add Kconfig
at_hdmac: move to generic DMA binding
ioatdma: ioat3_alloc_sed can be static
ioatdma: Adding write back descriptor error status support for ioatdma 3.3
ioatdma: S1200 platforms ioatdma channel 2 and 3 falsely advertise RAID cap
ioatdma: Adding support for 16 src PQ ops and super extended descriptors
ioatdma: Removing hw bug workaround for CB3.x .2 and earlier
dw_dmac: add ACPI support
dmaengine: call acpi_dma_request_slave_channel as well
dma: acpi-dma: introduce ACPI DMA helpers
dma: of: Remove unnecessary list_empty check
DMA: OF: Check properties value before running be32_to_cpup() on it
DMA: of: Constant names
ioatdma: skip silicon bug workaround for pq_align for cb3.3
ioatdma: Removing PQ val disable for cb3.3
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Currently the OF DMA code uses a spin lock to protect the of_dma_list from
concurrent access and a per controller reference count to protect the controller
from being freed while a request operation is in progress. If
of_dma_controller_free() is called for a controller who's reference count is not
zero it will return -EBUSY and not remove the controller. This is fine up until
here, but leaves the question what the caller of of_dma_controller_free() is
supposed to do if the controller couldn't be freed. The only viable solution
for the caller is to spin on of_dma_controller_free() until it returns success.
E.g.
do {
ret = of_dma_controller_free(dev->of_node)
} while (ret != -EBUSY);
This is rather ugly and unnecessary and none of the current users of
of_dma_controller_free() check it's return value anyway. Instead protect the
list by a mutex. The mutex will be held as long as a request operation is in
progress. So if of_dma_controller_free() is called while a request operation is
in progress it will be put to sleep and only wake up once the request operation
has finished.
This means that it is no longer possible to register or unregister OF DMA
controllers from a context where it's not possible to sleep. But I doubt that
we'll ever need this.
Also rename of_dma_get_controller back to of_dma_find_controller.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
of_dma_request_slave_channel() currently does not drop the reference to the
dma_spec of_node if no DMA controller matching the of_node could be found. This
patch fixes it by always calling of_node_put().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
if we initilize dma driver by module_init, there are still many devices
which will be initilized earlier than dma. these devices will fail to
get dma channel.
this moves dmaengine earlier than device_initcall and make dma available
for all devices.
Reported-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some Renesas USB modules have SUDMAC. This patch supports it using
the shdma-base driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds Kconfig in the drivers/dma/sh. This patch also adds
a new config "SH_DMAE_BASE" and the "config SH_DMAE" depends on it.
Since some drivers (e.g. sh_mmcif.c) depends on shdma-base.c if
CONFIG_DMA_ENGINE=y, the "config SH_DMAE_BASE" is set as "bool".
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Update at_hdmac driver to support generic DMA device tree binding. Devices
can still request channel with dma_request_channel() then it doesn't break
DMA for non DT boards.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The BUG_ON() directive is triggered probably due to a latency
modification following inclusion of commit c10d73671a ("softirq:
reduce latencies"). This condition has not been met before 3.9-rc1 and
doesn't trigger without this patch.
We now make sure that DMA channel is idle before calling
atc_complete_all() which makes the BUG_ON() "protection" useless.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
v3.3 provides support for write back descriptor error status. This allows
reporting of errors in a descriptor field. In supporting this, certain
errors such as P/Q validation errors no longer halts the channel. The DMA
engine can continue to execute until the end of the chain and allow software
to report the "errors" up the stack. We are also going to mask those error
interrupts and handle them when the "chain" has completed at the end.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This workaround checks for channel 2&3 and remove RAID cap.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
v3.3 introduced 16 sources PQ operations. This also introduced super extended
descriptors to support the 16 srcs operations. This patch adds support for
the 16 sources ops and in turn adds the super extended descriptors for those
ops.
5 SED pools are created depending on the descriptor sizes. An SED can be a 64
bytes sized descriptor or larger and must be physically contiguous. A kmem
cache pool is created for allocating the software descriptor that manages the
hardware descriptor. The super extended descriptor will take place of extended
descriptor under certain operations and be "attached" to the op descriptor
during operation. This is a new feature for ioatdma v3.3.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
CB3.2 and earlier hardware has silicon bugs that are no longer needed with
the new hardware. We don't have to use a NULL op to signal interrupt for
RAID ops any longer. This code make sure the legacy workarounds only happen on
legacy hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we have proper ACPI DMA helpers implemented, the driver may use it. This
patch introduces custom filter function together with acpi_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The slave device could be enumerated by ACPI. In that case the
dma_request_slave_channel should use the acpi_dma_request_slave_channel()
helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a new generic API to get a DMA channel for a slave device (commit
9a6cecc8 "dmaengine: add helper function to request a slave DMA channel"). In
similar fashion to the DT case (commit aa3da644 "of: Add generic device tree
DMA helpers") we introduce helpers to the DMAC drivers which are enumerated by
ACPI.
The proposed extension provides the following API calls:
acpi_dma_controller_register(), devm_acpi_dma_controller_register()
acpi_dma_controller_free(), devm_acpi_dma_controller_free()
acpi_dma_simple_xlate()
acpi_dma_request_slave_chan_by_index()
acpi_dma_request_slave_chan_by_name()
The first two should be used, for example, at probe() and remove() of the
corresponding DMAC driver. At the register stage the DMAC driver supplies a
custom xlate() function to translate a struct dma_spec into struct dma_chan.
Accordingly to the ACPI Fixed DMA resource specification the only two pieces of
information the slave device has are the channel id and the request line (slave
id). Those two are represented by struct dma_spec. The
acpi_dma_request_slave_chan_by_index() provides access to the specifix FixedDMA
resource by its index. Whereas dma_request_slave_channel() takes a string
parameter to identify the DMA resources required by the slave device. To make a
slave device driver work with both DeviceTree and ACPI enumeration a simple
convention is established: "tx" corresponds to the index 0 and "rx" to the
index 1. In case of robust configuration the slave device driver unfortunately
needs to call acpi_dma_request_slave_chan_by_index() directly.
Additionally the patch provides "managed" version of the register/free pair
i.e. devm_acpi_dma_controller_register() and devm_acpi_dma_controller_free().
Usually, the driver uses only devm_acpi_dma_controller_register().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
list_for_each_entry is able to handle empty lists just fine, there is no need
to make sure that the list is non empty.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In of_dma_controller_register() routine we are calling of_get_property() as an
parameter to be32_to_cpup(). In case the property doesn't exist we will get a
crash.
This patch changes this code to check if we got a valid property first and then
runs be32_to_cpup() on it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
No DMA of-function alters the name, so this patch changes the name arguments
to be constant. Most drivers will probably request DMA channels using a
constant name.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The alignment workaround is only necessary for cb3.2 or earlier platforms.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The PQ Val ops work on the newer hardware so we should actually provide support
for it and remove the disabling bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make it so only 3.2 and earlier platform need the PCI config register
clearings since this implementation does not have the registers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Intel Atom S1200 family ioatdma changed the channel reset behavior.
It does a reset similar to PCI FLR by resetting all the MSIX
registers. We have to re-init msix interrupts because of this. This
workaround is only specific to this platform and is not expected to carry
over to the later generations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The channel status register for v3.3 is now 64bit. Use readq if available
on v3.3 platforms.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
These should be good for the IOAT DMA devices on the Intel Atom S1269,
S1279, and S1289 platforms. We are also adding IOAT v3.3 definition for
the new DMA engine.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding Haswell PCI device IDs for ioatdma and simplify the detection of
certain Xeon CPUs that has alignment bugs so that modifications can be
changed at a single place going forward.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the device-tree blob is present during boot, then register the SDMA
controller with the device-tree DMA driver so that we can use device-tree
to look-up DMA client information.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If CONFIG_OF is not set the of_node of the device will always be NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The patch to add the common DMA binding added a dummy dw_dma_slave
structure into the dw_dma_chan structure in order to configure the
masters correctly. It turns out that this can be simplified if we
pick the DMA masters in the dwc_alloc_chan_resources function instead
and save them in the dw_dma_chan structure directly.
This could be simplified further once all users that today use
dw_dma_slave for configuration get converted to device tree based
setup instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since we will have not only DT cases in future let's rename DT related methods
to reflect their belonging.
The rename was done as follows:
struct dw_dma_filter_args -> struct dw_dma_of_filter_args
dw_dma_generic_filter() -> dw_dma_of_filter()
dw_dma_xlate() -> dw_dma_of_xlate()
dw_dma_id_table -> dw_dma_of_id_table
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Let's use capital letter as a first one in the comments.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The 'mask' parameter is not modified in __dma_request_channel and really
shouldn't be. Make this explicit by making the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
there is hardcode which enabled the clock of dmaengine before,
this patch takes the clock by standard clock API and enable it
in probe.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When we pause the channel after transfer is completed we might stuck in the
dwc_chan_pause() because the FIFO_EMPTY flag will never be asserted. To avoid
the endless loop we introduce a timeout here (*). The proper solution is to
somehow get the residue in FIFO and avoid busyloop when transfer is done, but
this task is not simple and fast.
Unfortunately we can't use cpu_relax() in conjunction with jiffies checker, due
to we have interrupts disabled by spin_lock_irqsave() and there is a big chance
that no interrupts will come to update the jiffies..
(*) The worst case is
AHB write * FIFO size / hclk = 5.12 us,
where
AHB write = 2 cycles,
hclk = 100 MHz,
burst size = 1 byte,
FIFO size = 256 bytes.
The proposed 40us timeout might be considered as a big one, though we enter
to that state only when we have the transfer already completed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit 84c1e63c12 (dma: Remove erroneous __exit and __exit_p() references)
the following section mismatch happens:
WARNING: drivers/built-in.o(.text+0x20f94): Section mismatch in reference from the function ipu_remove() to the function .exit.text:ipu_idmac_exit()
The function ipu_remove() references a function in an exit section.
Often the function ipu_idmac_exit() has valid usage outside the exit section
and the fix is to remove the __exit annotation of ipu_idmac_exit.
Remove the '__exit' annotation from ipu_idmac_exit in order to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxin B. John <maxin.john@enea.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Comparison between buffers is stored to the dedicated structure.
Note that the verify result is now accessible only via file 'results' in the
debugfs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The patch provides a storage for the test results in the linked list. The
gathered data could be used after test is done.
The new file 'results' represents gathered data of the in progress test. The
messages collected are printed to the kernel log as well.
Example of output:
% cat /sys/kernel/debug/dmatest/results
dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0)
The message format is unified across the different types of errors. A number in
the parens represents additional information, e.g. error code, error counter,
or status.
Note that the buffer comparison is done in the old way, i.e. data is not
collected and just printed out.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Its meaning is to limit amount of error messages to be printed out when buffer
mismatch is occured.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The following command should return actual state of the test.
% cat /sys/kernel/debug/dmatest/run
To wait for test done the user may perform a busy loop that checks the state.
% while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ]
> do
> echo -n "."
> sleep 1
> done
> echo
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Instead of doing
modprobe dmatest ...
modprobe -r dmatest
we allow user to run tests interactively.
The dmatest could be built as module or inside kernel. Let's consider those
cases.
1. When dmatest is built as a module...
After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest
folder with nodes will be created. They are the same as module parameters with
addition of the 'run' node that controls run and stop phases of the test.
Note that in this case test will not run on load automatically.
Example of usage:
% echo dma0chan0 > /sys/kernel/debug/dmatest/channel
% echo 2000 > /sys/kernel/debug/dmatest/timeout
% echo 1 > /sys/kernel/debug/dmatest/iterations
% echo 1 > /sys/kernel/debug/dmatest/run
After a while you will start to get messages about current status or error like
in the original code.
Note that running a new test will stop any in progress test.
2. When built-in in the kernel...
The module parameters that is supplied to the kernel command line will be used
for the first performed test. After user gets a control, the test could be
interrupted or re-run with same or different parameters. For the details see
the above section "1. When dmatest is built as a module..."
In both cases the module parameters are used as initial values for the test case.
You always could check them at run-time by running
% grep -H . /sys/module/dmatest/parameters/*
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Better to keep test parameters separate from internal variables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We don't need to have them global and later we would like to protect access to
them as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The proposed change will remove usage of the module parameters as global
variables. In future it helps to run different test cases sequentially.
The patch introduces the run_threaded_test() and stop_threaded_test() functions
that could be used later outside of dmatest_init, dmatest_exit scope.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This will help in future to hide a global variable usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If user have the timeout alike issues and wants to cancel the thread
immediately, the current call of wait_event_freezable_timeout is preventing to
this until timeout is expired. Thus, user will experience the unnecessary
delays.
Adding kthread_should_stop() check inside wait_event_freezable_timeout() solves
that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Looks like only the RAID channels are allowed to have irq coalescing support
in the existing code. Fixing that. The ioat3 cleanup code can handle memcpy
ops anyways
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Making OP field a hex instead of integer to make it more readable. Also add
the dump out of the NEXT field.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Removing the annotation with __exit and referencing with __exit_p()
present in dma driver module remove hooks.
Part of the __devexit and __devexit_p() purge.
Signed-off-by: Maxin B. John <maxin.john@enea.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix this compiler warning:
warning: 'td_remove' defined but not used [-Wunused-function]
Signed-off-by: Maxin B. John <maxin.john@enea.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
pdc_desc_get() is called from pd_prep_slave_sg, and the function is
called from interrupt context(e.g. Uart driver "pch_uart.c").
In fact, I saw kernel error message.
So, GFP_ATOMIC must be used not GFP_NOIO.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix the logic to allow mc programming of second transfer after first
has been done, by removing immediate return upon success and iterating
until we detect QFull or DMAC dying.
Reported-by: Alvaro Moran <dirac3000@gmail.com>
Tested-by: Alvaro Moran <dirac3000@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull slave-dmaengine fixes from Vinod Koul:
"The first one fixes issue in pl330 to check for DT compatible and
the second one fixes omap-dma to start without delay"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: omap-dma: Start DMA without delay for cyclic channels
DMA: PL330: Add check if device tree compatible
cyclic DMA is only used by audio which needs DMA to be started without a
delay.
If the DMA for audio is started using the tasklet we experience random
channel switch (to be more precise: channel shift).
Reported-by: Peter Meerwald <pmeerw@pmeerw.net>
CC: stable@vger.kernel.org # v3.7+
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update mxs-dma driver to adopt generic DMA device tree binding. It
calls of_dma_controller_register() with mxs specific of_dma_xlate to
get the generic DMA device tree helper support. Then DMA clients only
need to call dma_request_slave_channel() for requesting a DMA channel
from dmaengine.
The existing way of requesting channel, clients directly call
dma_request_channel(), still work there, and will be removed after
all mxs-dma clients get converted to generic DMA device tree helper.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Pull s390 fixes from Martin Schwidefsky:
"Just a bunch of bugfixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: provide emtpy check_pgt_cache() function
s390/uaccess: fix page table walk
s390/3270: fix minor_start issue
s390/uaccess: fix clear_user_pt()
s390/scm_blk: fix error return code in scm_blk_init()
s390/scm_block: fix printk format string
drivers/Kconfig: add several missing GENERIC_HARDIRQS dependencies
This patch register the dma controller with generic dma helpers only
in DT case. This also adds some extra error handling in the driver.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reported-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch is meant to be a follow-up for a patch originally submitted under
the title "ioat: Do not enable DCA if tag map is invalid". It was brought to
my attention that the preferred approach for BIOS workarounds is to set the
taint flag for TAINT_FIRMWARE_WORKAROUND for systems that require BIOS
workarounds.
This change makes it so that the DCA workarounds for broken BIOSes will now
use WARN_TAINT_ONCE(1, TAINT_FIRMWARE_WORKAROUND, ...) instead of just
printing a message via dev_err.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull second set of slave-dmaengine updates from Vinod Koul:
"Arnd's patch moves the dw_dmac to use generic DMA binding. I agreed
to merge this late as it will avoid the conflicts between trees.
The second patch from Matt adding a dma_request_slave_channel_compat
API was supposed to be picked up, but somehow never got picked up.
Some patches dependent on this are already in -next :("
* 'next' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw_dmac: move to generic DMA binding
dmaengine: add dma_request_slave_channel_compat()
The original device tree binding for this driver, from Viresh Kumar
unfortunately conflicted with the generic DMA binding, and did not allow
to completely seperate slave device configuration from the controller.
This is an attempt to replace it with an implementation of the generic
binding, but it is currently completely untested, because I do not have
any hardware with this particular controller.
The patch applies on top of the slave-dma tree, which contains both the base
support for the generic DMA binding, as well as the earlier attempt from
Viresh. Both of these are currently not merged upstream however.
This version incorporates feedback from Viresh Kumar, Andy Shevchenko
and Russell King.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Vinod Koul <vinod.koul@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Dan Williams <djbw@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull slave-dmaengine updates from Vinod Koul:
"This is fairly big pull by my standards as I had missed last merge
window. So we have the support for device tree for slave-dmaengine,
large updates to dw_dmac driver from Andy for reusing on different
architectures. Along with this we have fixes on bunch of the drivers"
Fix up trivial conflicts, usually due to #include line movement next to
each other.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (111 commits)
Revert "ARM: SPEAr13xx: Pass DW DMAC platform data from DT"
ARM: dts: pl330: Add #dma-cells for generic dma binding support
DMA: PL330: Register the DMA controller with the generic DMA helpers
DMA: PL330: Add xlate function
DMA: PL330: Add new pl330 filter for DT case.
dma: tegra20-apb-dma: remove unnecessary assignment
edma: do not waste memory for dma_mask
dma: coh901318: set residue only if dma is in progress
dma: coh901318: avoid unbalanced locking
dmaengine.h: remove redundant else keyword
dma: of-dma: protect list write operation by spin_lock
dmaengine: ste_dma40: do not remove descriptors for cyclic transfers
dma: of-dma.c: fix memory leakage
dw_dmac: apply default dma_mask if needed
dmaengine: ioat - fix spare sparse complain
dmaengine: move drivers/of/dma.c -> drivers/dma/of-dma.c
ioatdma: fix race between updating ioat->head and IOAT_COMPLETION_PENDING
dw_dmac: add support for Lynxpoint DMA controllers
dw_dmac: return proper residue value
dw_dmac: fill individual length of descriptor
...
Pull powerpc updates from Benjamin Herrenschmidt:
"So from the depth of frozen Minnesota, here's the powerpc pull request
for 3.9. It has a few interesting highlights, in addition to the
usual bunch of bug fixes, minor updates, embedded device tree updates
and new boards:
- Hand tuned asm implementation of SHA1 (by Paulus & Michael
Ellerman)
- Support for Doorbell interrupts on Power8 (kind of fast
thread-thread IPIs) by Ian Munsie
- Long overdue cleanup of the way we handle relocation of our open
firmware trampoline (prom_init.c) on 64-bit by Anton Blanchard
- Support for saving/restoring & context switching the PPR (Processor
Priority Register) on server processors that support it. This
allows the kernel to preserve thread priorities established by
userspace. By Haren Myneni.
- DAWR (new watchpoint facility) support on Power8 by Michael Neuling
- Ability to change the DSCR (Data Stream Control Register) which
controls cache prefetching on a running process via ptrace by
Alexey Kardashevskiy
- Support for context switching the TAR register on Power8 (new
branch target register meant to be used by some new specific
userspace perf event interrupt facility which is yet to be enabled)
by Ian Munsie.
- Improve preservation of the CFAR register (which captures the
origin of a branch) on various exception conditions by Paulus.
- Move the Bestcomm DMA driver from arch powerpc to drivers/dma where
it belongs by Philippe De Muyter
- Support for Transactional Memory on Power8 by Michael Neuling
(based on original work by Matt Evans). For those curious about
the feature, the patch contains a pretty good description."
(See commit db8ff907027b: "powerpc: Documentation for transactional
memory on powerpc" for the mentioned description added to the file
Documentation/powerpc/transactional_memory.txt)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (140 commits)
powerpc/kexec: Disable hard IRQ before kexec
powerpc/85xx: l2sram - Add compatible string for BSC9131 platform
powerpc/85xx: bsc9131 - Correct typo in SDHC device node
powerpc/e500/qemu-e500: enable coreint
powerpc/mpic: allow coreint to be determined by MPIC version
powerpc/fsl_pci: Store the pci ctlr device ptr in the pci ctlr struct
powerpc/85xx: Board support for ppa8548
powerpc/fsl: remove extraneous DIU platform functions
arch/powerpc/platforms/85xx/p1022_ds.c: adjust duplicate test
powerpc: Documentation for transactional memory on powerpc
powerpc: Add transactional memory to pseries and ppc64 defconfigs
powerpc: Add config option for transactional memory
powerpc: Add transactional memory to POWER8 cpu features
powerpc: Add new transactional memory state to the signal context
powerpc: Hook in new transactional memory code
powerpc: Routines for FP/VSX/VMX unavailable during a transaction
powerpc: Add transactional memory unavaliable execption handler
powerpc: Add reclaim and recheckpoint functions for context switching transactional memory processes
powerpc: Add FP/VSX and VMX register load functions for transactional memory
powerpc: Add helper functions for transactional memory context switching
...
This is a larger set of new functionality for the existing SoC families,
including:
* vt8500 gains support for new CPU cores, notably the Cortex-A9 based wm8850
* prima2 gains support for the "marco" SoC family, its SMP based cousin
* tegra gains support for the new Tegra4 (Tegra114) family
* socfpga now supports a newer version of the hardware including SMP
* i.mx31 and bcm2835 are now using DT probing for their clocks
* lots of updates for sh-mobile
* OMAP updates for clocks, power management and USB
* i.mx6q and tegra now support cpuidle
* kirkwood now supports PCIe hot plugging
* tegra clock support is updated
* tegra USB PHY probing gets implemented diffently
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PRrg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
Converting more ARM platforms to multiplatform support. This time, OMAP
gets converted, which is a major step since this is by far the largest
platform in terms of code size. The same thing happens to the vt8500
platform.
Conflicts include:
* Two mach/uncompress.h files are removed, the changes made to them
elsewhere can be discarded now.
* Moving the OMAP4 irq_match array has context clashes with turning
omap4_sar_ram_init into an omap_early_initcall()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUSUyOmCrR//JCVInAQI2zRAAnDUA3ufvANykRxNIII67D0u8XAgokzx6
hwq0ywwcQknd2aetN1khs2rY3sQ+T73CcsFzOR448YHjbWg1RCZlCzL89uUH6SdR
Bir/NC2jYkB1vSVB7krWhZzpeHNsFfWW1bCzwJzJfNmAZp64js3sOR1kRKjMpA2z
RGLktrFQ1JRKF/az+xnIsrleSnS2cQguPKIs5hYxPztzN/HdvbD7ZST0ttW7wqzg
C2AA5dnWs+C++pNXyfKlN+nL1CnyLWGXbuZUejUvAxYxgtyd/gC4/aTfNi8S9RNh
eiFTmVwl8lsWqPWx7yzyHk+p19x7ypfBgydLU/z4yC3asUJoN5jyCF6GSqzetHJB
jpDqTp3lQzIlJPgLryq07Xe38vUeVIKvV4e8ySOsSBlKr6aRl5684HJSCAZR9SFa
qzHavusA5JZJKf+94UbDCPNzSqzMQYnILA039M8ekvrMZhFG89St0+NLDaxVQfO/
OrTEnwth/TJBKvOUPIuamjZzHH/RiGkumWiKrEGKOlpwHPGtdglQeziJFo8pNkwR
hjtnwn4RPPK8FIl59fERFI1hRvhUlwuhYcA2R/WTjcZw2d+jwZPzhhun37dLMVlw
fk5lhz0GBaRUmua4xFqJTkpOwHf2l/9wbzhEpmL4c/ZSrtjYwfeL/tY6aT9e8MZK
INaMr7X2QTw=
=nl4h
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform support from Arnd Bergmann:
"Converting more ARM platforms to multiplatform support. This time,
OMAP gets converted, which is a major step since this is by far the
largest platform in terms of code size. The same thing happens to the
vt8500 platform."
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
ARM: OMAP2+: Make sure files with omap initcalls include soc.h
ARM: OMAP2+: Include soc.h to drm.c to fix compiling
ARM: OMAP2+: Fix warning for hwspinlock omap_postcore_initcall
ARM: multi_v7_defconfig: add ARCH_ZYNQ
ARM: multi_v7_defconfig: remove unnecessary CONFIG_GPIOLIB
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
ARM: OMAP2+: Remove now obsolete uncompress.h and debug-macro.S
ARM: OMAP2+: Add minimal support for booting vexpress
ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support
ARM: OMAP2+: Disable code that currently does not work with multiplaform
ARM: OMAP2+: Add multiplatform debug_ll support
ARM: OMAP: Fix dmaengine init for multiplatform
ARM: OMAP: Fix i2c cmdline initcall for multiplatform
ARM: OMAP2+: Use omap initcalls
ARM: OMAP2+: Limit omap initcalls to omap only on multiplatform kernels
* Updates to the ux500 cpufreq code
* Moving the u300 DMA controller driver to drivers/dma
* Moving versatile express drivers out of arch/arm for sharing with arch/arm64
* Device tree bindings for the OMAP General Purpose Memory Controller
There is a simple conflict in drivers/cpufreq/dbx500-cpufreq.c, because
the mach/id.h header and the cpu_is_u8500_family() function in it are
now gone.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=R0p0
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
- Updates to the ux500 cpufreq code
- Moving the u300 DMA controller driver to drivers/dma
- Moving versatile express drivers out of arch/arm for sharing with arch/arm64
- Device tree bindings for the OMAP General Purpose Memory Controller
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
ARM: OMAP2+: gpmc: add DT bindings for OneNAND
ARM: OMAP2+: gpmc-onenand: drop __init annotation
mtd: omap-onenand: pass device_node in platform data
ARM: OMAP2+: Prevent potential crash if GPMC probe fails
ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
arm: Move sp810.h to include/linux/amba/
ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
ARM: OMAP: gpmc-nand: drop __init annotation
mtd: omap-nand: pass device_node in platform data
ARM: OMAP: gpmc: don't create devices from initcall on DT
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
...
<<
Please pull mpc5xxx patches for v3.9. The bestcomm driver is
moved to drivers/dma (so it will be usable for ColdFire).
mpc5121 now provides common dtsi file and existing mpc5121 device
trees use it. There are some minor clock init and sparse fixes
and updates for various 5200 device tree files from Grant. Some
fixes for bugs in the mpc5121 DIU driver are also included here
(Andrew Morton suggested to push them via my mpc5xxx tree).
>>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRAuO3AAoJEHm+PkMAQRiGbfAH/1C3QQKB11aBpYLAw7qijAze
yOui26UCnwRryxsO8zBCQjGoByy5DvY/Q0zyUCWUE6nf/JFSoKGUHzfJ1ATyzGll
3vENP6Fnmq0Hgc4t8/gXtXrZ1k/c43cYA2XEhDnEsJlFNmNj2wCQQj9njTNn2cl1
k6XhZ9U1V2hGYpLL5bmsZiLVI6dIpkCVw8d4GZ8BKxSLUacVKMS7ml2kZqxBTMgt
AF6T2SPagBBxxNq8q87x4b7vyHYchZmk+9tAV8UMs1ecimasLK8vrRAJvkXXaH1t
xgtR0sfIp5raEjoFYswCK+cf5NEusLZDKOEvoABFfEgL4/RKFZ8w7MMsmG8m0rk=
=m68Y
-----END PGP SIGNATURE-----
Merge branch 'omap/multiplatform-fixes', tag 'v3.8-rc5' into next/multiplatform
The omap multiplatform support uncovered a bug in the cwdavinci_cpdma
code and was missing two drivers that are enabled now but are not
quite ready for multiplatform, as found by allyesconfig builds.
There is also a conflict generated by automated merge in
arch/arm/mach-omap2/drm.c between a bug fix that went into v3.8-rc5
and a different version of the same fix that went into the
omap/multiplatform branch. This merge removes the extraneous
#include that was causing build errors.
* omap/multiplatform-fixes:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch registers the pl330 dma controller driver with the generic
device tree dma helper functions.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add xlate to translate the device-tree binding information into
the appropriate format. The filter function requires the dma
controller device and dma channel number as filter_params.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds a new pl330_dt_filter for DT case to filter the
required channel based on the new filter params and modifies the
old filter only for non-DT case as suggested by Arnd Bergmann.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to assign 0 to residue, because dma_cookie_status() does this
for us.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Accordingly to commentary in the platform_device_register_full the memory
allocated for dma_mask will not going to be freed. That's why is better to
assign dma_mask afterwards.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When status is DMA_SUCCESS the residue should be zero. Otherwise it's a bug.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In case the len is 0 we must return without trying to unlock the lock that was
not locked.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It's possible to have an inconsistency in the list due to unprotected operation
on it. The patch adds a proper locking on the list operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix dma_tc_handle() to call d40_desc_remove() and d40_desc_done() only
for non-cyclic transfers, as this was breaking ux500_pcm since
introduced in:
d49278e dmaengine: dma40: Add support to split up large elements
Reported-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The memory allocated to ofdma might be a leakage when error occurs.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In some cases we got the device without dma_mask configured. We have to apply
the default value to avoid crashes during memory mapping.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a race that can hit during __cleanup() when the ioat->head pointer is
incremented during descriptor submission. The __cleanup() can clear the
PENDING flag when it does not see any active descriptors. This causes new
submitted descriptors to be ignored because the COMPLETION_PENDING flag is
cleared. This was introduced when code was adapted from ioatdma v1 to ioatdma
v2. For v2 and v3, IOAT_COMPLETION_PENDING flag will be abandoned and a new
flag IOAT_CHAN_ACTIVE will be utilized. This flag will also be protected under
the prep_lock when being modified in order to avoid the race.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Intel Lynxpoint PCH Low Power Subsystem has DMA controller to support general
purpose serial buses like SPI, I2C, and HSUART. This controller is enumerated
from ACPI namespace with ACPI ID INTL9C60.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRCYtBAAoJEMzrak5tbycxKb8P/0cXt2X7mPfoApWV96bI2c9h
VE1wZYREcq0Au3hiNuMmPp1Nwous2zvrXRKXMvLoQi42KwpvZlFjlyn8+xACKmxO
okSJ+aXETzlGh85l5RlnFJMgq181Kn0nDhN5Iwy0FUEJ8/oqdS8fEz5mwQlHflX1
CLaquDVr/edr8LffvsFlxtSmeYNvZ2jYkSgroWeDhVR5Np1/LUCyh5y3edjVl/es
B0/keuZ2fnYZnEfqLTpBEARYDBimymuu8gIoHK5nvtz3d/GGu92sVeda4LuHt8eH
1N+f41ceDR2JG/MIJbLr6PGYmCkAGSM/5Vcfa33G+A7GQT0EVb8jLozGCdrCjaEG
OM33pN5wtv1M9gTLR9swITBWhbTpRWaHnXeZQF7ttaV8dvr/fuOzWBw47k8Jw0FJ
zjGta66kwW7WkT3HDNoM2RRzm9dlJr1xdHOzAaVJnX3VHtHcIvYzDi90Xv9Nn46D
E/qIpExmL4rMrb2+4MxT9CdbfzdBSmsnlRFoWZTIM1NPxA/97i7oAyYVAJ34LCNx
xWqwimhXK14LzGffpSHm9CSz8DHNbehDZRMQD0jGYMn61PFtDB+E/oEq5AEqneuC
KDht3Qdx/mPzJQPE8WV3d5FxeXfXDjj203x/i6x8TOdH8Bt4aoK9ajvPYBpA+2aE
4fPJIobLHGYN/F+GF1VJ
=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
* Move sp810 header to a more generic location,
mainly to share it with arm64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCULAAAoJEL9jRaJfXa5PyysH/AsFbihoAGU0S7o+ggyN4S8m
5myEfbdMvgI5Hjcl/MgcVJAl6jFpDjmBH5ZPu+o8WzoP5L91C9F//kMRZqK0zATj
Y2OdMVNfVQG94bSsmjHryWF8W0RYcY2bQr0wJmgguNDpRLFsFdF3Rb58AWzG+2tP
KFxDg9u/CyhC/sv7BzoKI+J3ol5wEmv4BNMbPyjYG8L5TcBfe/IZqnl6KZ/QAw5i
QUFs3oXtT4/v8bnsxAym+VXIvjSHWs2t0CivfMyH+ZIgb3NbfJ1gIOCOJIk5XWTu
6L1yYyBBcRr60y9p4s2Nd4NxHZEB7pyZYuboUOxSmRNnEM54RT2Nkvcdon8j6Rw=
=uB7w
-----END PGP SIGNATURE-----
Merge tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux into next/drivers
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
DMA controller down into the driver and cleans up in
the <mach/*> namespace for the U300 platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=IGqm
-----END PGP SIGNATURE-----
Merge tag 'coh901318-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
This pushes the platform data for the U300 COH901318
DMA controller down into the driver and cleans up in
the <mach/*> namespace for the U300 platform.
* tag 'coh901318-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dma: coh901318: cut down on platform data abstraction
dma: coh901318: merge header files
dma: coh901318: push definitions into driver
dma: coh901318: push header down into the DMA subsystem
dma: coh901318: skip hard-coded addresses
dma: coh901318: remove hardcoded target addresses
dma: coh901318: push platform data into driver
dma: coh901318: create a proper platform data file
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-u300/core.c
Migrate Tegra clock support to drivers/clk/tegra, this involves
moving:
1. definition of tegra_cpu_car_ops to clk.c
2. definition of reset functions to clk-peripheral.c
3. change parent of cpu clock.
4. Remove legacy clock initialization.
5. Initialize clocks using DT.
6. Remove all instance of mach/clk.h
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: use to_clk_periph_gate().]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Currently the driver returns full length of the active descriptor which is
wrong. We have to go throught the active descriptor and substract the length of
each sent children in the chain from the total length along with the actual
data in the DMA channel registers.
The cyclic case is not handled by this patch due to len field in the descriptor
structure is left untouched by the original code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It will be useful to have the length of the transfer in the descriptor. The
cyclic transfer functions remained untouched.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
By this new field we distinguish a total length of the chain and the individual
length of each descriptor in the chain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The soft LLP mode is working for active descriptor only. So, we do not need to
have a copy of its pointer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It's usefull to have the values of the DW_PARAMS and DWC_PARAMS printed when
debug mode is enabled.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Just like Russell pointed out in "DMAEngine: sirf: add DMA
pause/resume support" at
http://www.spinics.net/lists/arm-kernel/msg212496.html
here I find sirfsoc_dma_terminate_all() has same problem,
so move the locking to the front of registers access.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
pause/resume are important for users like ALSA sound drivers,
this patches make the sirf prima2/marco support DMA commands
DMA_PAUSE and DMA_RESUME.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes on slave dmanengine. There are trivial fixes in imx-dma,
tegra-dma & ioat driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: implement flags parameters for cyclic transfer
dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
ioat: Fix DMA memory sync direction correct flag
The proper place for the main logic of the soft LLP mode is
dwc_scan_descriptors. It prevents to get the transfer unexpectedly aborted in
case the user calls dwc_tx_status.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver assumes that hardware has two AHB masters which might not be always
true. In such cases we must not exceed number of the AHB masters present in the
hardware. In the proposed scheme in this patch, we would choose the master with
highest possible number whenever we exceed max AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently descriptors are allocated from normal cacheable memory and that slows
down filling the descriptors, as we need to call cache_coherency routines
afterwards. It would be better to allocate memory for these descriptors from
DMA_COHERENT memory. This would make code much cleaner too.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
the variable chan is dereferenced in line 635, so it is no reason to check
null again in line 641.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
the pointer cfg is dereferenced in line 594, so it's no reason to check null
again in line 620.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The edma_slave_config() implementation depends on the
direction field such that it will not properly configure
a slave channel when called without direction set.
This fixes the implementation so that the slave config
is copied as is and prep_slave_sg() handles the
direction dependent handling. spi-omap2-mcspi and
omap_hsmmc both expose this bug as they configure the
slave channel config from a common path with an unconfigured
direction field.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clock code was changed to use clk_prepare_enable in:
b707c65 dma/ste_dma40: Fixup clock usage during probe
but clk_disable on probe fail path was not updated. This patch fix this
by using clk_disable_unprepare in place of clk_disable.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Some DMA channels may be used by other cores in the SoC. This patch
modifies the dma interrupt handler to ignore interrupts from unknown
channels.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
This patch add support to manage LLI by SW for select phy channels.
There is a HW issue in certain controllers due to which on certain
occassions HW LLI cannot be used on some physical channels. To avoid
the HW issue on a specific phy channel, the phy channel number can be
added to the list of soft_lli_channels and there after all the transfers
on that channel will use software LLI, for peripheral to memory
transfers.
SoftLLI introduces relink overhead, that could impact performace for
certain use cases.
This is based on a previous patch of Narayanan Gopalakrishnan.
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Use internal variables to the cycles to improve code readability, no
functional changes.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
This is to keep the active queue for only those transfers which are
actually active in the hardware. Descriptors will be moved to the done
queue after they are completed in the hardware (interrupt handler) but
before all the cleanup work has been completed (tasklet).
Mostly based on a previous patch by Rabin Vincent.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
U8540 DMA controller is different from u9540 we need define new
registers and use them to support handling more than 128 event lines.
Signed-off-by: Tong Liu <tong.liu@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
DMAC_ICFG[0:2]=SCHNB only allows to count 'multiple of 4' physical
channels so it was ok with platforms having 8 channels but cannot be
used for next versions (with 10 or 14 channels). This patch allows to
provide the number of physical channels for a DMA device via
platform_data, or still rely on SCHNB if platform_data announces 0
channel.
Signed-off-by: Gerald Baeza <gerald.baeza@stericsson.com>
Reviewed-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Hardware bug: when a logical channel is triggerred by a high priority
destination event line, an extra packet transaction is generated in case
of important data write response latency on previous logical channel A
and if the source transfer of current logical channel B is already
completed and if no other channel with a higher priority than B is
waiting for execution.
Software workaround: do not set the high priority level for the
destination event lines that trigger logical channels.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
The check for runtime suspend is not needed during a regular suspend, as
the framework takes care of this. This fixes the issue of DMA driver
not letting the system to go to deepsleep in the first attempt.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
The client is not aware of the maximum burst size in the dma driver. If
the size exceeds 16 set max to 16.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Maximum DMA seg size is (0xffff x data_width). If max seg
size is not set it deafults to 64k. This results in failure
if transferring 64k in byte mode.
Large seg sizes may be supported by splitting large transfer.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
lcpa and lcla are written often and the cache_sync() overhead in writel
is costly, especially for wlan where every single network packet (in RX
mode) corresponds to a separate DMA transfer.
Signed-off-by: Per Forlin <per.forlin@stericsson.com>
Reviewed-by: Narayanan Gopalakrishnan <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
This patch sets the SSCFG/SDCFG bit[7] PRI only for physical channel
requests with high priority. For logical channels, this bit will be
zero.
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
The header is used by drivers/dma/amba-pl08x.c, which can be compiled
under x86, where PL080 exists under a PCI-to-AMBA bridge. This patche
moves it where it can be accessed by other architectures, and fixes
all users.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DMA transfer could not be established if previously it was paused and
terminated. In that case the channel's suspend bit remains set that prevents to
transfer anything until channel is resumed.
The patch adds the dwc_chan_resume() call instead of a plain flag assignment.
That clears the DWC_CFGL_CH_SUSP bit as well during termination.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The same information could be extracted from the struct dma_chan.
The patch introduces helper function dwc_get_data_width() as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The driver requires a custom slave configuration to be present to be able to
make the slave transfers. Nevertheless, in some cases we need only the request
line as an additional information to the generic slave configuration. The
request line is provided by slave_id parameter of the dma_slave_config
structure. That's why the custom slave configuration could be optional for such
cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the direction value comes from the generic slave configuration
structure and explicitly as a preparation function parameter. The first one is
kinda obsoleted. Thus, we have to store the value passed to the preparation
function somewhere in our structures to be able to use it later. The best
candidate to provide the storage is a custom channel structure. Until now we
still keep and check the direction field of the slave config structure as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If we don't yet have the platform device for the driver when it is being loaded
we fail to probe the driver. So instead of calling probe() directly we call
platform_driver_register(). It will call the probe() immediately if we have the
device but also makes the driver to work on platforms where the platform device
is created later.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Jingoo Han