Remove an erroneous BUG_ON() in the case of a hard reset timeout. The
reset timeout handler puts the port into the "awaiting link-up" state.
The timeout causes the device to be disconnected and we need to be in
the awaiting link-up state to re-connect the port. The BUG_ON() made
the incorrect assumption that resets never timeout and we always
complete the reset in the "resetting" state.
Testing this patch also uncovered that libata continues to attempt to
reset the port long after the driver has torn down the context. Once
the driver has committed to abandoning the link it must indicate to
libata that recovery ends by returning -ENODEV from
->lldd_I_T_nexus_reset().
Cc: <stable@vger.kernel.org>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reported-by: David Milburn <dmilburn@redhat.com>
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Xun Ni <xun.ni@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It seems the "phy_index++;" have been placed in wrong place, without it
the while circle up will do a infinite loop.
Signed-off-by: Xinghai Yu <yuxinghai@cn.fujitsu.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing. However, the implementation is not correctly syncing with the
port configuration agent. In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.
Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.
Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
When the first phy of a wide port comes up, don't report the port ready
yet, always wait for 250 miliseconds then config the port with all phys
added to the port. So that we can avoid reporting wide port device too
early to kernel, which caused the first IOs (report luns, inquirys)
failed due to not all the phys are configured into its port. Changes
also made that the phys in a wide port don't need to go through half
second wait time for consuming power.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When hot insert the wide port device through the mini-sas port,
the first IOs (Report Luns or Inquiry) may fail due to the device
trying to open to a SCU phy that is still in suspended state. This
IO failure causes the wide port device stuck in UPDATING_PORT_WIDTH
state.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Needed to jump to scic_lock unlock.
Also spotted by coccicheck.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Most of these simple dereference macros are longer than their open coded
equivalent. Deleting enum sci_controller_mode is thrown in for good
measure.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_. The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.
Also unwind the 'sds1' out of the parameter structs.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost). Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_port (local instances named iport). The duplicate '->owning_port' and
'->isci_port' in both isci_phy and isci_remote_device will be fixed in a later
patch... this is just the straightforward rename/unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
They are one in the same object so remove the distinction. The near
duplicate fields (owning_port, and isci_port) will be cleaned up
after the scic_sds_port isci_port unification.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This cleans up several areas of the state machine mechanism:
o Rename sci_base_state_machine_change_state to sci_change_state
o Remove sci_base_state_machine_get_state function
o Rename 'state_machine' struct member to 'sm' in client structs
o Shorten the name of request states
o Shorten state machine state names as follows:
SCI_BASE_CONTROLLER_STATE_xxx to SCIC_xxx
SCI_BASE_PHY_STATE_xxx to SCI_PHY_xxx
SCIC_SDS_PHY_STARTING_SUBSTATE_xxx to SCI_PHY_SUB_xxx
SCI_BASE_PORT_STATE_xxx to SCI_PORT_xxx and
SCIC_SDS_PORT_READY_SUBSTATE_xxx to SCI_PORT_SUB_xxx
SCI_BASE_REMOTE_DEVICE_STATE_xxx to SCI_DEV_xxx
SCIC_SDS_STP_REMOTE_DEVICE_READY_SUBSTATE_xxx to SCI_STP_DEV_xxx
SCIC_SDS_SMP_REMOTE_DEVICE_READY_SUBSTATE_xxx to SCI_SMP_DEV_xxx
SCIC_SDS_REMOTE_NODE_CONTEXT_xxx_STATE to SCI_RNC_xxx
Signed-off-by: Edmund Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
While cleaning up the driver it is very tempting to convert scic_sds_get_*
macros to their open coded equivalent. They are all just pointer dereferences
*except* scic_sds_phy_get_port() which returns NULL if the phy is assigned to
the dummy port. Clarify this by renaming it to phy_get_non_dummy_port().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* Move port configuration agent implementation
* Merge core/scic_sds_port.[ch] into port.[ch]
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams