Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update all open-coded tests for all 4 PHY_INTERFACE_MODE_RGMII* values
to use the newly introduced helper: phy_interface_is_rgmii.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ethtool command is used to set the speed of the device while
the device is down, the check to set the initial mode may fail when
the device is brought up, causing failure to bring the device up.
Update the code to set the initial mode based on the desired speed if
auto-negotiation is disabled.
This patch fixes a bug introduced by:
d9663c8c21 ("amd-xgbe-phy: Use phydev advertising field vs supported")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pair of nested spin locks was introduced in commit 63502b8d0
"dp83640: Fix receive timestamp race condition".
Unfortunately the 'flags' parameter was reused for the inner lock,
clobbering the originally saved IRQ state. This patch fixes the issue
by changing the inner lock to plain spin_lock without irqsave.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of the ext_write function are supposed to hold a mutex that
protects the state of the dialed page, but one caller was missing the
lock from the very start, and over time the code has been changed
without following the rule. This patch cleans up the call sites in
violation of the rule.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the calibration function that corrects the initial offsets
among multiple devices only works the first time. If the function is
called more than once, the calibration fails and bogus offsets will be
programmed into the devices.
In a well hidden spot, the device documentation tells that trigger indexes
0 and 1 are special in allowing the TRIG_IF_LATE flag to actually work.
This patch fixes the issue by using one of the special triggers during the
recalibration method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.
Fixes: d068b02cfd ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an alternative way of fixing:
commit db9683fb41 ("net: phy: Make sure PHY_RESUMING state change
is always processed")
When the PHY state transitions from PHY_HALTED to PHY_RESUMING, there are
two things we need to do:
1). Re-enable interrupts (and power up the physical link, if powered down)
2). Update the PHY state and net-device based on the link status.
There's no strict reason why #1 has to be done from within the main
phy_state_machine() function. There is a risk that other changes to the
PHY (e.g. setting speed/duplex, which calls phy_start_aneg()) could cause
a subsequent state transition before phy_state_machine() has processed
the PHY_RESUMING state change. This would leave the PHY with interrupts
disabled and/or still in the BMCR_PDOWN/low-power mode.
Moving enabling the interrupts and phy_resume() into phy_start() will
guarantee this work always gets done. As the PHY is already in the HALTED
state and interrupts are disabled, it shouldn't conflict with any work
being done in phy_state_machine(). The downside of this change is that if
the PHY_RESUMING state is ever entered from anywhere else, it'll also have
to repeat this work.
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy_start_aneg() was called while the phydev is in the PHY_RESUMING
state, then its state would immediately transition to PHY_AN (or
PHY_FORCING). This meant the phy_state_machine() never processed the
PHY_RESUMING state change, which meant interrupts weren't enabled for the
PHY. If the PHY used low-power mode (i.e. using BMCR_PDOWN), then the
physical link wouldn't get powered up again.
There seems no point for phy_start_aneg() to make the PHY_RESUMING -->
PHY_AN transition, as the state machine will do this anyway. I'm not sure
about the case where autoneg is disabled, as my patch will change
behaviour so that the PHY goes to PHY_NOLINK instead of PHY_FORCING. An
alternative solution would be to move the phy_config_interrupt() and
phy_resume() work out of the state machine and into phy_start().
The background behind this: we're running linux v3.16.7 and from user-space
we want to enable the eth port (i.e. do a SIOCSIFFLAGS ioctl with the
IFF_UP flag) and immediately afterward set the interface's speed/duplex.
Enabling the interface calls .ndo_open() then phy_start() and the PHY
transitions PHY_HALTED --> PHY_RESUMING. Setting the speed/duplex ends up
calling phy_ethtool_sset(), which calls phy_start_aneg() (meanwhile the
phy_state_machine() hasn't processed the PHY_RESUMING state change yet).
Signed-off-by: Tim Beale <tim.beale@alliedtelesis.co.nz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be useful to debug the PHY state machine, add dynamic debug
prints of the old and new PHY devices state under a friendly format.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RGMII interfaces come in multiple flavors: RGMII with transmit or
receive internal delay, no delays at all, or delays in both direction.
This change extends the initial check for PHY_INTERFACE_MODE_RGMII to
cover all of these variants since EEE should be allowed for any of these
modes, since it is a property of the RGMII, hence Gigabit PHY capability
more than the RGMII electrical interface and its delays.
Fixes: a59a4d1921 ("phy: add the EEE support and the way to access to the MMD registers")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also changes mii_bus.phy_mask to u32 for consistency.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update mdiobb_read() to read whether the PHY has a broken turn-around,
and if it does, ignore it to make the read succeeed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't do clock-mode-select if clk == NULL,
since when building without CONFIG_HAVE_CLK,
clk_get returns NULL and clk_get_rate returns 0.
Doing clock-mode-select in this cause causes kszphy_probe to
return -EINVAL and thus prevents the device from being probed.
The original code (before regression) would return 0
when building without CONFIG_HAVE_CLK.
Cc: stable <stable@vger.kernel.org> # 3.18+
Fixes: 1fadee0c36 ("net/phy: micrel: Add clock support for
KSZ8021/KSZ8031")
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Niklas Cassel <niklass@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bus id was supplied via a struct platform_device, the driver wasn't
handling -1 to mean an unspecified id of the only instance of this driver,
as the platform spec requires.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The amd-xgbe driver currently only works with the Seattle SoC, which
is ARM64 architecture, so there is no point in building this driver on
other architectures except for build testing purpose. The dependency
list can be updated later if the driver ever supports other
architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new gpiod_get_array and gpiod_put_array functions
(added to mainline in the v4.1 merge window) for obtaining and
disposing of GPIO descriptors.
Cc: David Miller <davem@davemloft.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some systems using mdio-gpio may use gpio on message based busses, which
require sleeping (e.g. gpio from an I2C I/O expander).
Since this driver does not use IRQ handler, it is safe to use the
_cansleep suffixed gpio accessors.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently fixed_phy uses a callback to periodically poll the link state.
This patch adds the fixed_phy_update_state() API.
It solves the following problems:
- On link state interrupt, MAC driver can't update status.
Instead it needs to provide the callback to periodically query
the HW about the link state. It is more efficient to update status
after interrupt.
- The callback needs to be unregistered before phy_disconnect(),
or otherwise it will be called with net_dev==NULL. phy_disconnect()
does not have enough info to unregister the callback automatically.
- The callback needs to be registered before of_phy_connect() to
avoid running with outdated state, but of_phy_connect() returns the
phy_device pointer, which is needed to register the callback. Registering
it before of_phy_connect() will therefore require a hack to get the
pointer earlier.
Overall, this addition makes the subsequent patch that implements
SGMII link status for mvneta, much cleaner.
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Moreover use devm_gpiod_get_optional instead of ignoring all errors
returned by devm_gpiod_get and simplify accordingly.
The result is more strict error handling which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device stores the number of seconds in a 32 bit register, and the
stored value is unsigned. Therefore this driver and device are ready
for the year 2038. However, more work will be needed prior to 2106.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no interrupt code that indicates auto-negotiation
has timed out. If the auto-negotiation has timed out then the start of
a new auto-negotiation will begin again with a new base page being
received. The state machine could be in a state that is not expecting
this interrupt code which results in an error during auto-negotiation.
Update the code to timestamp when the auto-negotiation starts. Should
another page received interrupt code occur before auto-negotiation has
completed but after the auto-negotiation timeout, then reset the state
machine to allow the auto-negotiation to continue.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the setting of the transceiver type when retrieving the device
settings using ethtool and instead set the transceiver type in the
phy_driver structure flags field. Change the transceiver type to be
internal, also.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ethtool being able to control what is advertised, the advertising
field is what should be used for priming the auto-negotiation registers
and for various other checks, instead of the supported field.
Also, move the initial setting of the supported and advertising fields
into the probe function so that they are not reset each time the device
is brought up, thus allowing the user to set as desired before bringing
the device up.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7439 has an alternate PHY OUI: 0xae025080 which is to be found in
some variants of this chip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY requires different settings for the Decision Feedback Analyzer
(DFE) when running in KX mode vs. KR mode. Update the code to change
these settings when changing modes in order to provide a more stable
link.
Additionally, adjust the 10GbE PQ skew default setting to a more sane
value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_init_eee uses phy_find_setting(phydev->speed, phydev->duplex)
to find a valid entry in the settings array for the given speed
and duplex value. For full duplex 1000baseT, this will return
the first matching entry, which is the entry for 1000baseKX_Full.
If the phy eee does not support 1000baseKX_Full, this entry will not
match, causing phy_init_eee to fail for no good reason.
Fixes: 9a9c56cb34 ("net: phy: fix a bug when verify the EEE support")
Fixes: 3e7077067e ("phy: Expand phy speed/duplex settings array")
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode for all Micrel PHYs
using IRQ line as a NAND-tree toggle mode at reset.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to see the old value of the LP advertising flags
through ethtool after reconfiguring the PHY and before autonegotiation
completes. If autonegotiation is turned off then the last value seen
will persist indefinitely.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a call to ndo_close() a netdevice driver may call
phy_disconnect() -> phy_detach() -> phy_suspend(), such that the PHY is
suspsended at this point and a netdevice driver may clock gate the
backing peripheral providing MDIO bus accessses as well.
Update mdio_bus_phy_may_suspend() to return whether a PHY is allowed to
be suspended and conversely resumed if and only if it was not previously
suspended before while it is currently in detached (netdev pointer is
NULL) state.
This fixes bus errors seen during S2/S3 suspend/resume cycles for
netdevice drivers such as GENET which clock gates the entire Ethernet
MAC, including the MDIO bus block.
Acked-by: Fugang Duan <B38611@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid double calls to phydev->drv->suspend and resume, keep
track of whether the PHY has already been suspended as a consequence of
a successful call to phy_suspend(). We will use this in our MDIO bus
suspend/resume hooks to avoid a double suspend call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend and phy_resume are an abstraction on top of the PHY device
driver suspend and resume callbacks, utilize those since they are the
proper interface to suspending and resuming a PHY device.
Acked-by: Fugang Duan <B38611@freescale.com>
Tested-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fixed_phy_set_link_update() contains an early check against a NULL
callback pointer, which basically prevents us from removing any
previous callback we may have set. The users of the fp->link_update
callback deal with a NULL callback just fine, so we really want to allow
"removing" a link_update callback to avoid dangling callback pointers
during e.g: module removal.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain PHY settings need to be configurable by UEFI depending on the
platform being used. Add new device tree / ACPI properties that, if
present, will override the pre-determined values currently used.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ACPI to the amd-xgbe and amd-xgbe-phy drivers. This
support converts many of the device tree APIs to the new device_property
APIs.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving and processing extended next pages the base registers
were used instead of the XNP registers. Update the code to use the
device XNP and link partner XNP registers.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advertise and apply the Forward Error Correction capabilities of the
device based on the FEC ability of the device. Also, remove the use
of some hard coded values related to KR and FEC in preference of some
#defines.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The auto negotiation logic was geared to being the initiator of the
auto negotiation. This presented problems when auto negotiation was
initiated by the remote end. Change the auto negotiation logic to
make use of the auto negotiation event interrupt thus allowing the
auto negotiation state machine to function properly in either scenario.
This also removes the polling during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reads to registers are undefined when the PCS is powered down. To be
safe, save the CTRL1 register used for power down during suspend and
restore that value during resume.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This set of patches resolves some checks reported by the checkpatch
tool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic config_init callback also for KSZ8021 and KSZ8031.
This has been avoided this far due to commit b838b4aced ("phy/micrel:
KSZ8031RNL RMII clock reconfiguration bug"), which claims that the PHY
becomes unresponsive if the broadcast-disable flag is set before
configuring the clock mode.
Turns out that the problem seemingly worked-around by the above
mentioned commit was really due to a hardware-configuration issue, where
the PHY was in fact strapped to address 3 rather than 0.
Tested-by: Bruno Thomsen <bth@kamstrup.dk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Murphy