In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate. Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.
This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported. It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SDIO Simplified Specification V2.00 states that it is strongly recommended
that the host executes either a power reset or issues a CMD52 (I/O Reset)
to re-initialize an I/O only card or the I/O portion of a combo card.
Additionally, the CMD52 must be issued first because it cannot be issued
after a CMD0.
With this patch the Nintendo Wii SDIO-based WLAN card is detected after a
system reset, without requiring a complete system powercycle.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
And bring them back to 4-bit mode during resume.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards may suspend while keeping function interrupts active
especially in the powered suspend case. Upon resume we need to kick the
SDIO interrupt thread to check for pending interrupts and to restart card
IRQ detection at the host controller level.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Seen on a Marvell 8686 SDIO card and Via VX855 controller: we must avoid
sending CMD3/5/7 on a resume where power has been maintained, because the
8686 will refuse to respond to them and the MMC stack will give up on the
card.
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series provides the core changes needed to allow SDIO cards to
remain powered and active while the host system is suspended, and let them
wake up the host system when needed. This is used to implement
wake-on-lan with SDIO wireless cards at the moment. Patches to add that
support to the libertas driver will be posted separately.
This patch:
Some SDIO cards have the ability to keep on running autonomously when the
host system is suspended, and wake it up when needed. This however
requires that the host controller preserve power to the card, and
configure itself appropriately for wake-up.
There is however 4 layers of abstractions involved: the host controller
driver, the MMC core code, the SDIO card management code, and the actual
SDIO function driver. To make things simple and manageable, host drivers
must advertise their PM capabilities with a feature bitmask, then function
drivers can query and set those features from their suspend method. Then
each layer in the suspend call chain is expected to act upon those bits
accordingly.
[akpm@linux-foundation.org: fix typo in comment]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDIO cards expect byte transfers not to exceed the configured block
transfer size. Add a quirk to that effect.
Patches to make use of this quirk will be sent separately.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Drake noticed a crash in the error path of mmc_attach_sdio(). This
bug is discussed at http://dev.laptop.org/ticket/9707.
BUG: unable to handle kernel paging request at 6b6b6c57
IP: [<b066d6e2>] sdio_remove_func+0x9/0x27
Call Trace:
[<b066cfb4>] ? mmc_sdio_remove+0x34/0x65
[<b066d1fc>] ? mmc_attach_sdio+0x217/0x240
[<b066a22f>] ? mmc_rescan+0x1a2/0x20f
[<b042e9a0>] ? worker_thread+0x156/0x1e
We need to accurately track how many SDIO functions have been initialised
(and keep card->sdio_funcs in sync) so that we don't try to remove more
functions than we initialised if we hit the error path in
mmc_attach_sdio().
Without this patch if we hit the error path in mmc_attach_sdio() we run
the risk of deferencing invalid memory in sdio_remove_func(), leading to a
crash.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Cc: Daniel Drake <dsd@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sdio_remove_func() needs to be more careful about reference counting. It
can be called in error paths where sdio_add_func() has never been called
e.g. mmc_attach_sdio error path --> mmc_sdio_remove --> sdio_remove_func
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.
In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend. So there are
two possible behaviours, each of which will cause data loss in some cases:
CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend. Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.
CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend. They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.
Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rework the current CIS tuple parsing code, reusing the existing
infrastructure and providing an easy way to add new CISTPL_FUNCE parsers
by TPLFE_TYPE.
Valid known CIS tuples are now silently queued for the SDIO function
driver when not parsed/processed (-EILSEQ) by the SDIO core. Unknown CIS
tuples (-ENOENT) are queued too for the SDIO function driver without
aborting the initialization, but emit a warning in the kernel log.
CISTPL_FUNCE tuples can be "whitelisted" now by adding a matching entry to
the cis_tpl_funce_list table.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Pierre Ossman <pierre@ossman.eu>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PC Card 8.0 specification (vol. 4, section 3.2.10) says the
TPLLV1_INFO field of the CISTPL_VERS_1 tuple must contain 4 strings. Some
cards don't have all 4 so just parse as many as we can.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Tested-by: Jonathan Cameron <jic23@cam.ac.uk>
Tested-by: Bing Zhao <bzhao@marvell.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some manufacturers provide vendor information in non-vendor specific CIS
tuples. For example, Broadcom uses an Extended Function tuple to provide
the MAC address on some of their network cards, as in the case of the
Nintendo Wii WLAN daughter card.
This patch allows passing whitelisted FUNCE tuples unknown to the SDIO
core to a matching SDIO driver instead of rejecting them and failing.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Especially with the PM framework, those are quite handy to have in driver
code too.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Especially for SDIO drivers which may have special conditions/errors to
report, it is a good thing to relay the returned error code back to upper
layers.
This also allows for the rationalization of the resume path where code to
"remove" a no-longer-existing or replaced card was duplicated into the
MMC, SD and SDIO bus drivers.
In the SDIO case, if a function suspend method returns an error, then all
previously suspended functions are resumed and the error returned. An
exception is made for -ENOSYS which the core interprets as "we don't
support suspend so just kick the card out for suspend and return success".
When resuming SDIO cards, the core code only validates the manufacturer
and product IDs to make sure the same kind of card is still present before
invoking functions resume methods. It's the function driver's
responsibility to perform further tests to confirm that the actual same
card is present (same MAC address, etc.) and return an error otherwise.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all SDIO cards are virtually removed upon a suspend, and
completely reprobed upon a resume. This adds the suspend and resume
methods to the SDIO bus driver so to be able to dispatch those events to
the actual SDIO function drivers for real suspend/resume instead.
All active functions on a card must have a driver with both a suspend and
a resume method though. Failing that, we fall back to the current
behavior of simply "removing" the card when suspending.
When resuming, we make sure the same card is still inserted by comparing
the vendor and product IDs. If there is a mismatch, or if there is simply
no card anymore in the slot, then the previous card is "removed" and the
new card is detected. This is further enhanced with the next patch.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some time ago, I have send a patch to the mmc_spi subsystem changing the
error codes. This was after a discussion with Pierre about using EINVAL
only for non-recoverable errors. This patch was accepted as
http://git.kernel.org/linus/fdd858db7113ca64132de390188d7ca00701013d
Unfortunately, several weeks later, I realized that this patch has opened
a little can of worms because there are SD cards on the market which
a) claim that they support the switch command
AND
b) refuse to execute this command if operating in SPI mode.
So, such a card would get unusuable in an embedded linux system in SPI
mode, because the init sequence terminates with an error.
This patch adds the missing error codes to the caller of the switch
command and restores the old behaviour to fail gracefully if these
commands can not execute.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org> [2.6.31.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Normally writes to SDIO function 0 outside the vendor specific CCCR
registers are prohibited.
To support embedded devices that require writes to SDIO function 0 outside
this range (e.g. TI WL127x embedded sdio wifi device),
MMC_QUIRK_LENIENT_FN0 is introduced.
A card quirks field is added to `struct mmc_card' to support non-standard
devices (e.g. embedded sdio devices).
[akpm@linux-foundation.org: code in C, not cpp!]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to disconnect the pull-up resistor on CD/DAT[3] (pin 1)
of the card. This may be desired on certain setups of boards,
controllers and embedded sdio devices which do not need the card's
pull-up. As a result, card detection is disabled and power is saved.
[akpm@linux-foundation.org: simplify sdio_disable_cd() a bit]
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the standard, the SWITCH command should be followed by a
SEND_STATUS command to check for errors.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Power can be saved by powering off cards that are not in use. This is
similar to suspend / resume except it is under the control of the driver,
and does not require any power management support. It can only be used
when the driver can monitor whether the card is removed, otherwise it is
unsafe. This is possible because, unlike suspend, the driver still
receives card detect and / or cover switch interrupts.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eMMC's are not removable, so unsafe resume is OK always.
To permit this a new host capability MMC_CAP_NONREMOVABLE has been added
and suspend / resume updated accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change allows the MMC host to be claimed in situations where the host
may or may not have already been claimed. Also 'mmc_try_claim_host()' is
now exported.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MMC hosts that support power saving can use the 'enable' and 'disable'
methods to exit and enter power saving states. An explanation of their
use is provided in the comments added to include/linux/mmc/host.h.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed for 1.8V embedded SDIO devices and supporting host controllers
(e.g. TI 127x and ZOOM2 boards)
Signed-off-by: Ohad Ben-Cohen <ohad@bencohen.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When mmc_power_up is called during unsafe resume, host->ocr should be used
instead of host->ocr_avail.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Philip Langdale <philipl@overt.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some controllers allow a much lower frequency than 400kHz.
Keep the minimum frequency within sensible limits.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
With this patch, mmc_rescan can detect the removal of an mmc card and
the insertion of (possibly another) card in the same run. This means
that a card change can be detected without having to call
mmc_detect_change multiple times.
This change generalises the core such that it can be easily used by
hosts which provide a mechanism to detect only the presence of a card
reader cover, which has to be taken off in order to insert a card. Other
hosts ("card detect" or "MMC_CAP_NEEDS_POLL") each receive an event when
a card is removed and when a card is inserted, so it is sufficient for
them if mmc_rescan handles only one event at a time. "Cover detect"
hosts, however, only receive events about the cover status. This means
that between 2 subsequent events, both a card removal and a card
insertion can occur. In this case, the pre-patch version of mmc_rescan
would only detect the removal of the previous card but not the insertion
of the new card.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The TI controller on Toshiba Tecra M5 needs more time to power up or
the cards will init incorrectly or not at all.
Signed-off-by: José M. Fernández <josemariafg@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
atmel-mci: fix sdc_reg typo
tmio_mmc: add maintainer
mmc: Add OpenFirmware bindings for SDHCI driver
sdhci: Add quirk for forcing maximum block size to 2048 bytes
sdhci: Add quirk for controllers that need IRQ re-init after reset
sdhci: Add quirk for controllers that need small delays for PIO
sdhci: Add set_clock callback and a quirk for nonstandard clocks
sdhci: Add get_{max,timeout}_clock callbacks
sdhci: Add support for hosts reporting inverted write-protect state
sdhci: Add support for card-detection polling
sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
sdhci: Split card-detection IRQs management from sdhci_init()
sdhci: Add support for bus-specific IO memory accessors
mmc_spi: adjust for delayed data token response
omap_hsmmc: Wait for SDBP
omap_hsmmc: Fix MMC3 dma
omap_hsmmc: Disable SDBP at suspend
omap_hsmmc: Do not prefix slot name
omap_hsmmc: Allow cover switch to cause rescan
omap_hsmmc: Add 8-bit bus width mode support
...
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.
These calls are intended to be used by MMC host adapters
using at least one regulator per host. Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
During mmc unsafe resume, choose the right voltage for the card after
powerup.
Although this has not seen to cause trouble, it's the wrong behaviour.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Extended CSD is a MMC card register. As increasingly interesting
fields are being added to Extended CSD, it is helpful to see its
value. Note that SD cards do not have an Extended CSD
register, so it is MMC only.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently we are using an explicit udev rule to trigger loading of the
mmc-block module when an MMC or SD card is detected:
SUBSYSTEM=="mmc", RUN+="/sbin/modprobe -Qba mmc-block"
It makes much more sense for the mmc bus driver and the mmc-block module to
share MODALIAS information so that they are linked automatically.
There is no real information of use in the MMC system at the current time.
All devices inserted require us to load the mmc-block device. Until such
time as useful parameters exist simply reflect the module linkage via
the module alias below:
mmc:block
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The delayed work item mmc_host.detect is now cancelled before flushing
the work queue. This takes care of cases when delayed_work was scheduled
for mmc_host.detect, but not yet placed in the work queue.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Commit 0d3e0460f3
"MMC: CSD and CID timeout values" inadvertently broke
the timeout for the MMC command SEND_EXT_CSD.
This patch puts it back again.
Depending on the characteristics of the controller,
this bug may prevent the use of MMC cards.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Get rid of a silent failure mode when the MMC/SD host doesn't
support the voltages needed to operate a given card, by
adding a warning. A 3.3V host and a 3.0V card, for example,
no longer need to mysteriously just not work at all.
This isn't the best diagnostic; ideally it would also tell
what voltage the card and host support (and not just by
dumping the bitmasks).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This function sets the OCR mask bits according to provided voltage
ranges. Will be used by the mmc_spi OpenFirmware bindings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Adrian Hunter