When a Tx hang happens, usually the Tx queue disable fails. At
this point if we try to recover by a VSI reinit the HW gets
unhappy and we get a Malicious Driver Detect (MDD) event.
HW expects a PF reset if a queue disable fails, if we don't do a PF
reset and restart the queue we get an MDD. This patch makes sure we
do a PF reset on Tx hang and that way we avoid any MDD because of Tx
queue disable failure.
Change-ID: I665ab6223577c788da857ee2132e733dc9a451e4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF reset to clean up at the end of the remove is a nice thing
to do, but it also removes any LAA setting that Wake On LAN wants
for future wake up.
Change-ID: Ic090ec714df2d722281d11735cf75f2aa4432e2c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LAA is lost on a reset, so be sure to replay it when rebuilding
the switch after any reset.
Change-ID: I6e643f9a59dfd899b6cbdf84d93b4bc9c37bb949
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't short-circuit the LAA assignment when the driver thinks it has
already been done - it is possible that the user might want to force
the address setting again. At the same time, this requires a little
re-ordering of the filter management.
Change-ID: Ia0d71e3bc04edd7b68cf67edecc00abe7b9f6639
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Firmware sets up the LAA as a Wake-On-LAN address.
Change-ID: I57b9acd8c288424fcfed0911053eb725c400b41c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the i40e_set_coalesce function to allow 0 as a disable
value. Also, added message to user about invalid value and provides valid
range.
Change-ID: I6c9ff11a9861f2045bd543745a3d132999ffbbd8
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This log print message will probably never be seen, but it needs to match
the "attempting to rebuild switch\n" log message a few lines above.
Change-ID: Ic3f5b4f67568d721cb02e826cf2cb33847f51c11
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the firmware's API minor number is larger than the one expected, log
a warning and recommend driver SW update.
If the firmware's API major or minor number is smaller then the one expected
(n for major, n or n-1 for minor), log a warning and recommend NVM update.
Change-ID: If0b887e055478f8e435ba7fa28113b63a6f1bb35
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the spec when the PF driver receives a Malicious driver event
the queue that caused the event is already stopped and it is expected
that the function that owns the queue will reset the queue.
In some cases it may not be possible to determine the queue and it is
suggested to reset the whole function.
This patch takes the later approach when the event is owned by the PF
that owns it.
Change-ID: I40f9764a6a5e068c0ef8438db00c5aa9c2c6c1c8
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The return from i40e_prep_for_reset() was being ignored by almost all
its callers. The one place it wasn't ignored could have caused a silent
and confusing failure of the driver to finish a reset. Since we really
are doing a rebuild anyway, ignore this last case as well and simply
make the function a void type.
Change-ID: Ia4fed7f903d39a6c47c5722625a53e59c3f7ed53
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the RSS configuration to set table size
and write to hardware to confirm RSS table size being used.
Change-ID: I455a4c09c9dd479f5791ee1f09fdc83ff9908df5
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the service tasks don't try to meddle with the
device while a reset is in progress. Odd things can happen
such as funky stats values.
Change-ID: I6929cb9d6d96839c9279362ca7c0e3fe6c8fcc66
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VEB really is part of the whole PF and should be cleared
at the same time.
Change-ID: Ia1d4d1df5cf421f2578a22486650dd256cc4617a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The bug is encountered when all the Tx hang recovery mechanisms have
failed and driver tries to bring down the interface in the interrupt context.
The patch defers this and schedules it for next cycle.
Change-ID: Id9cd1da15b0e5c018dce18da4d0eed5ef1e8a809
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Introduce helper routines that would wait for the Rx/Tx queue
to reach the enable or disable state as requested.
Change-ID: I518d9d0e2afef3f45107af3b46e9af402ff587c3
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we resize the number of queues, the driver needs to disassociate any
qvectors that are no longer in use from the original rings, this way we
do not try to access the rings through these qvectors at the time of freeing
the qvectors.
Change-ID: Ie4eb9fc749f8e12348517fe1560f599c58f4a2a4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The NVM wasn't filling in the GLQF_HKEY register on
some old NVM versions. If this is the case, fill
in some values so receive with flow rules works right.
Change-ID: Ic737888ee68f96efb4cf8a1a49d2301615e09ed2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This updates the register file for new hardware.
The format of the file has changed requiring drivers to
declare I40E_MASK. I40E_MASK is to be used with 32 bit registers.
This patch also updates the drivers to accommodate the register changes.
Change-ID: If9bc8d736391024cbf99054efe50f9acc12ee4f1
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.
Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default. The system
must request a VLAN tag packet filter to get packets with that tag.
Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.
This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.
Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bumpity and Fred Worm say it's time to change the numbers again.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I658731d022ea23cedede4be2bfecd8b4cc68d270
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We tell the HW upper boundary of power of 2 in VSI config,
but the HW does not restrict us to use just power of 2 GPS in
case of RSS as long as we are not sharing the RSS table with
another VSI (VMDq). We at present are not doing RSS in VMDq
VSI.
If we were to enable that and if the system had CPU count which
was not power 2, the VMDq VSIs will see a little skewed distribution.
Change-ID: I3ea797ce9065a3ca4fc4d04251bf195463410473
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FD_SB and FD_ATR needs to be checked independently in order to decide if
we will support multiple queues or not.
Change-ID: I9d3274f5924c79e29efdbcf66a2fcca1fee2107f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the logic in i40e_determine_queue_usage() so that
SR-IOV doesn't get turned off unnecessarily.
Change-ID: I86ca304fa9f742a50e9ea831b887f358a6a9d53d
Signed-off-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way resources are distributed to special features.
Change-ID: I847e49d714a1d70e97f3f994cb39bfb5e02ab016
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware supports VF antispoofing for both MAC addresses and VLANs.
Enable this feature by default for all VFs and implement the netdev op
to control it from the command line.
Change-ID: Ifb941da22785848aa3aba6b2231be135b8ea8f31
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to complain in the log about mac addresses that
can't be deleted because they don't exist.
Change-ID: I4e6370df175bf72726f06d2206c03bcbfded8387
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was a vestige of early driver development that no longer
has any actual use.
Change-ID: I95b5b19c4bbfaff8759197af671ebaf716cb6ab5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of VSIs that the firmware reports to us is a guaranteed
minimum, not an absolute maximum. The hardware actually supports far
more than the reported value, which we often need.
To allow for this, we allocate space for a larger number of VSIs than is
guaranteed by the firmware, with the knowledge that we may fail to get
them all in the future.
Note that we are just allocating pointers here, the actual (much larger)
VSI structures are allocated on demand.
Change-ID: I6f4e535ce39d3bf417aef78306e04fbc7505140e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for error status bits on the AdminQ event queue and announce them
if seen. If the Firmware sets these bits, it will trigger an AdminQ
interrupt to get the driver's attention to process the ARQ, which will
likely be enough to clear the actual issue.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I009e0ebc8be764e40e193b29aed2863f43eb5cb0
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.5 and i40evf to 0.9.29.
Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove two device IDs 1582 and 1573, because they will not be shipped.
Change-ID: Ica2e550b5b21a69e3f353eba2fe5e1c532a548c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a coding error where during the registration for NAPI
the driver requested 256 budget. The max recommended
value for this is NAPI_POLL_WEIGHT or 64.
Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.
Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.
Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once more, with feeling: not all VSIs have rings. To assume so is to
invite null pointers to your party.
Change-ID: I576858824468d9712d119fa1015a1f28c27712c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Be sure to clear PXE mode bit on each reset after AdminQ has been rebuilt.
Change-ID: I992d8c79594f8ca0660c50844ace675ecb9c9bf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where FD SB/ATR and NTUPLE configurations status are
reported erroneously. Without this patch, driver reports FDir without further
information.
Change-ID: I5bdd2871b7f2db1e5f5e76c741ae6a0dc603b453
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. There is no ixgbe_watchdog_task function in the driver, so change
the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
because it is never used.
3. Remove some TBD comments that are not needed.
Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use an extra state variable to keep track of when the IRQs are fully
set up. This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.
Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up. We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.
Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver should print link messages like all the
other Intel Ethernet drivers.
Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing unicast, multicast, and broadcast stats for the port.
Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.
Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware are not expected to work correctly
with revision_id 0 hardware. Don't prevent the user from
using it, but be sure to print a warning.
Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.
Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.
Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.
Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.
Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.
Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.
Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.
The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.
Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If pf_reset failed, it becomes necessary to clear recovery pending bit, instead
of falling through the setup process.
Change-ID: Ic1611e6a32741fe3a2782ec7be173cb65e7492ed
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The storm control features are not part of the hardware
and mistakenly were left in the code. Remove them as
they are not needed any more.
Change-ID: I6e9277c8da2c52e69348a657bae25271449c2099
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a function to calculate this, so update the code to use the function.
Change-ID: Ia345b6fe6ec7f0b2dcf1199471b0d0f959ad3908
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the declaration of Tx/Rx rings inside several loops. It
eliminates declaring the same rings every time for the duration of the loop,
instead declaring them once before the loop.
Change-ID: I59dea54276f18c47dca522f520c18f65fe42a15d
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to igb, igbvf, ixgbe, i40e and i40evf.
Jacob provides eight patches to cleanup the ixgbe driver to resolve various
checkpatch.pl warnings/errors as well as minor coding style issues.
Stephen Hemminger and I provide simple cleanups of void functions which
had useless return statements at the end of the function which are not
needed.
v2: Dropped Emil's patch "ixgbe: fix the detection of SFP+ capable interfaces"
while I wait for his updated patch to be validated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove cases where useless bare return is left at end of function.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 6c167f582e ("i40e: Refactor and cleanup i40e_open(),
adding i40e_vsi_open()") introduced a new function i40e_vsi_open()
with the regression by a typo. Due to the commit, the wrong error
code would be passed to i40e_open(). Fix this error in
i40e_vsi_open() by turning the macro into a negative value so that
i40e_open() could return the pertinent error code correctly.
Fixes: 6c167f582e ("i40e: Refactor and cleanup i40e_open(), adding i40e_vsi_open()")
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The call to i40e_alloc_vfs needs to be wrapped in CONFIG_PCI_IOV because
the function itself is wrapped in the same conditional compile block.
Change-ID: I663c5f1b85e5cfba0b36da8966f7db1a034f408b
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool consistently reports 0 values for our ITR settings because
we never actually set them. Fix this by setting the default values
to the specified default values.
Change-ID: I2832406a66f7140f2b1230945d6ff6cbf77467c8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the formal parameters to remove argument which is no longer used.
Change-ID: I493b56eba74a1f396fa1b7d24c0a4acbe536b5bf
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Although NTUPLE feature control is disabled by default, do not
allow user to be able to change it.
Change-ID: I4c3f95fb6dbc56b1b6cc47116ea1f72de02bc99c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In case of any AQ command to query port's DCB configuration fails
during driver's probe time; the probe fails and returns an error.
This patch prevents this issue by continuing the driver probe even
when an error is returned.
Also, added an error message to dump the AQ error status to show what
error caused the failure to get the DCB configuration from firmware.
Change-ID: Ifd5663512588bca684069bb7d4fb586dd72221af
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The queue vectors are originally distributed among the total
number of queues that are configured for a given VSI. The number
of queues that are configured for a VSI depends on the number of
TCs that are enabled for the VSI at VSI setup/creation time.
But, the total number of queues that are configured for a VSI may
change based on change in the total number of TCs enabled as a
result of change in DCB configuration based on DCBX.
Hence, it is required for the queue vectors to be redistributed
when the total queues that are configured for a given VSI changes.
Without redistributing the vectors the queues that are configured
for the newly enabled TCs may not be able to do any Tx/Rx.
Change-ID: I4e780903db019e6199c7ce43627cef22c916acfe
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver version string was added to this struct to be passed
down through the firmware to low-level NC-SI functions. We tell
the firmware about the length of the ASCII string not counting
any terminating null.
Change-ID: I09ac98ff9b869e8661c55fc6a5c98808fc280c91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Anjali Singhai <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.
This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.
Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/igb/e1000_mac.c
net/core/filter.c
Both conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to version 0.3.43 and i40evf to version 0.9.21.
Change-ID: Ice4c715731bfa1dfc12dd45418675a3ba6e08d57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the newer i40e_vsi_open() and i40e_vsi_close() in the FDIR VSI
lifetime. This makes sure we're using standard methods for all the
VSI open and close paths. This also fixes a memory leak of the
FDIR queue buffer info structs across a reset.
Change-ID: I1b60a1b08ab923afe4f49810c2c7844d850e19b9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the new i40e_vsi_open() for waking VSIs back up in order to
be sure all the standard actions happen.
Change-ID: Ic3479410dd3079733f4951dcea69f101e69e77df
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Abstract out the vsi close actions into a single function so they
can be used correctly for both netdev and non-netdev based VSIs.
Change-ID: I59e3d115fcb20e614a09477281b7787dd340d276
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the FW workaround to increment the number of msix vectors.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PREFENA field in the receive host memory cache (RX-HMC)
must be visible in order to be set to 1 at driver init for
best performance.
Change-ID: I16b0bcd84cf56f4b6c938201ff5e954bee5a1992
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the netdev ops to support addition of static FDB entries in the
physical function (PF) MAC/VLAN filter table so that virtual functions
(VFs) can communicate with bridged virtual Ethernet ports such as those
provided by the virtio driver.
Change-ID: Ifbd6817a75074e3b5cdf945a5635f26440bf15df
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the i40e driver was allowing the hardware
to replicate the PSH flag on all segments of a TSO operation.
This patch fixes the first/middle/last TCP flags settings which
makes the TSO operations work correctly.
With this change we are now configuring the CWR bit to only be set
in the first packet of a TSO, so this patch also enables TSO_ECN,
in order to advertise to the stack that we do the right thing
on the wire.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit 6494294f27 ("i40e/i40evf: Use
dma_set_mask_and_coherent") uses dma_set_mask_and_coherent() to
replace dma_set_coherent_mask() for the benefit of return error.
The conversion brings some confusion in error checking as whether
against DMA_BIT_MASK(64) or DMA_BIT_MASK(32). For one, if error is
zero, the check will be against DMA_BIT_MASK(64) twice. Fix this
error checking by binding the check to the pertinent one.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to verify the eeprom checksum and firmware crc status bits,
and shutdown the driver if they fail. This code stops the processing of traffic,
but doesn't kill the PF netdev so that the NVMUpdate process should still have a
chance at fixing the image. The eeprom is checked on driver load and after an
EMP reset, the latter of which should be generated after an NVMUpdate.
Change-ID: I34deef21d2e16bf5a43c603cf8af27e6a29dc9d2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's annoying to search for a matching alloc and free set of function calls
when they don't use the same framework for the name of the functions. Fix
that up in the case of alloc and free of vsi queue vectors.
i40e_vsi_free_q*
i40e_vsi_alloc_q*
Change-ID: I510eb863a0fbe405312bebea55c2846c76285e6d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.
Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to. Enable this feature.
Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up and moves a portion of i40e_open to i40e_vsi_open,
in order to have a shorter vsi_open function that does only that.
Change-ID: I1c418dda94dcfc0eb7d4386a70c330692ef5ecc9
Signed-off-by: Elizabeth Kappler <elizabeth.m.kappler@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.
Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.
Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.
Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The networking core does it for the driver during registration time.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Linux 3.13, dma_set_mask_and_coherent was introduced, and we have
been encouraged to use it. It simplifies the DMA mapping code a bit as
well.
Change-ID: I66e340245af7d0dedfa8b40fec1f5e352754432e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have a separate handler for MDD events, a generic reset is not required.
Change-ID: I77858e2d479e4e65c52aede67109464649ea0253
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FDIR replay logic was being run a little too soon (before the
queues were enabled) and hence the tail bump was not effective till
a later transaction happened on the queue.
Change-ID: Icfd7cd2e79fc3cae3cbd3f703a2b3a148b4e7bf6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to enforce the following policy:
- If the HW reports filter programming error, we check if it's due to a
full table.
- If so, we go ahead and turn off new rule addition for ATR and then SB
in that order.
- We monitor the programmed filter count, if enough room is created due
to filter deletion/reset, we then re-enable SB and ATR new rule addition.
Change-ID: I69d24b29e5c45bc4fa861258e11c2fa7b8868748
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In a similar way to how ixgbe works, print a short one-line string
showing what features and number of queues the driver and hardware has
enabled at probe time.
Example (wrapped for the commit message):
i40e 0000:06:00.1: Features: PF-id[1] VFs: 64 VSIs: 66 QP: 32 FDir RSS
ATR NTUPLE DCB
Change-ID: I177bf7f93d1c4c921529c92fdf66e614f6b4f755
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the strings that the driver prints during normal
operation and moves many strings into dev_dbg. It also cleans up
strings printed during reset.
Change-ID: I1835cc4e3c3b22596182b683284e6bb87eac61b2
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This cleans up strings for consistency, q is replaced with queue.
Change-ID: Ia5f9dfae9af261f4c24485854264e02363729cf3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We've been deleting the netdev before getting around to deleting the napi
structs. Unfortunately, we then didn't delete the napi structs because we
have a check for netdev, thus we were leaving garbage around in the system.
Change-ID: Ife540176f6c9f801147495b3f2d2ac2e61ddcc58
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to use the format that the current NVM
uses when printing the version of the NVM. It should remain
this way from now on forward.
The driver was reporting when firmware was less than
an expected version number, but this is not a requirement
for the product and we print the firmware number at
init and in ethtool -i output. Just remove the print.
Change-ID: Ide0b856cd454ebf867610ef9a0d639bb358a4a60
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Number of MSIX vectors being reported is correct and hence
we need a check to do the right thing for FWs before and after.
Change-ID: I50902d1c848adcb960ea49ac73f7865ca871a1c3
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix inconsistent use of MSIX and MSI-X in messages.
Change-ID: Iae9ffb42819677c34544719044ed77632e06147d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the do/while to a for loop, so we don't hit the delay each
time, even when the register is ready for action.
Don't bother to set or clear the QENA_STAT bit as it is
read-only.
Change-ID: Ie464718804dd79f6d726f291caa9b0c872b49978
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the DOWN flag before attempting to disable VFs when unloading the
driver. Also, don't attempt to reset the VFs when the driver is
unloading, because the switch configuration will fail. This fixes a
panic on unload when VFs are enabled.
Change-ID: I25a6567e89c9687145f510ff4f630932412c5c5d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If VFs are present when the driver loads, then set up some resources
so they can function.
Change-ID: I485916a811609a9990ce663d06dc645f625b07ff
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset all of the VFs after a PF reset, so that they are in a known
state, and the VF driver can detect the reset and reinit itself.
Change-ID: I93c5b3a0f8b1371d0da078f92de948b9d3a6413f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tx_timeout recovery failed, then it becomes necessary to set
i40e_down bit before actually shutdown the connection.
Change-ID: Iaac81df0e302116571827aa0cff450697fbb7fa3
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.31-k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b044 ("i40e: add DCB and DCBNL support")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the device ID #defines to follow the _DEV_ID convention
already established in the other Intel drivers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds capability to configure DCB on i40e network
interfaces using Intel XL710 adapter firmware APIs.
By default all VSIs are only enabled for the default traffic
class enabled by firmware for any given PF. The driver would
query the firmware for the traffic classes that are enabled for
the port and reconfigure the LAN VSI to match to the port traffic
class settings. All other VSIs are only enabled for the default
traffic class settings for now.
The driver registers and listens to firmware events that may
require change in the DCB settings. It may reconfigure the VSI
settings based on these events.
This patch exposes IEEE DCBNL interfaces for the i40e driver to
allow any application to query the DCB settings on the adapter.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-By: Jack Morgan<jack.morgan@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e hardware was generating some inconsistent results
when using current programming methods. This refactor
fixes the inconsistencies that were preventing clean
unloads of the driver, and moves the queues for handling
flow director errors into their own hardware VSI.
This patch also implements a corrected version of the
basic ethtool add ntuple rule, which will disable
the driver's automatic flow programming. A future patch
adds remove/replay/list support for ntuple.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FLAG_FDIR_* defines can be renamed to be more descriptive.
This patch is in preparation for the following where the fdir
code is refactored.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix more whitespace issues, including making some locals declared
in a nicer order.
Also update Copyright string printed when the driver loads.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a workaround that is no longer necessary and implement
a better understanding of what firmware is returning in the MSI-X
vector count. This makes it so that the driver ends up with the
right amount of queues when using all available MSI-X vectors.
Change-ID: I34e60cc71dcfb1b5412f37df956fedcc49ade187
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.30-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some whitespace and comment issues.
Change-ID: I1587599e50ce66fd389965720e86f9e331d86643
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where the queue was not associated with the right set-up
within the hardware. The fix is to use the right QTX_CTL VSI type
when associating it to the VSI.
Change-ID: I65ef6c5a8205601c640a6593e4b7e78d6ba45545
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.28-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.
Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.
Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed. Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.
Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver needs to set the MFP flag earlier in i40e_sw_init
and then can use that flag to decide if other hardware
work-arouds are required.
Change-ID: Ib17ad1e3485f57b28845ab4722294a99f203bd48
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The alloc_rx_buff_failed and alloc_rx_page_failed variables
are both part of an rx specific structure so just remove
the _rx part of the name. No functional changes.
Change-ID: Icffa2f5d13c6f2b1e09cf45b9472b83c9dae8fc6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The admin queue can be used to send messages among the physical
function interfaces. This adds the code to handle that case.
Change-ID: I0700fcc47e41433131a381f0eb72fc7b01b6bd87
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
RSS initialization was doing some extra work, remove the extra
work and any bugs it created when managing number of queues.
Change-ID: Iea75b04a70d73ce76947b6a177ce89ab4899d4c6
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware support splitting packets on headers
but with the use of GRO we don't need the extra bus
overhead, so make this driver more like igb and ixgbe and
disable packet split.
Change-ID: Id42f2c3736baa9d5bdfe1f72d64226e7d8ebd737
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The memory barrier used in maybe_stop_tx can use a comment.
Also add checks to VSI->rx_rings to ensure a kernel panic is not induced.
Change-ID: I48cc1bf1d6cf301818155b737edeef77c0d790c7
Change-ID: I1363a8445fbf521a26267849966296ed55f43ad8
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The GPL header included in each file in the i40e driver doesn't
need to include the "this program" text since this driver
is already part of the larger kernel.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The hardware can occasionally give an interrupt on the misc
queue for which there is no driver work to do. In that case
the driver was not re-enabling interrupts even though they
were auto masked by hardware. This left interrupts disabled
on this queue.
Re-enable the interrupt whenever leaving this function.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anjali Singhai Jain