When the run bit is set in the xHCI command register, it may take a few
microseconds for the host to start running. We cannot ring any doorbells
until the host is actually running, so wait until the status register says
the host is running.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Shinya Saito <shinya.saito.sx@renesas.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After software resets an xHCI host controller, it must wait for the
"Controller Not Ready" (CNR) bit in the status register to be cleared.
Software is not supposed to ring any doorbells or write to any registers
except the status register until this bit is cleared.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Blackfin code is incorrectly casting the argument to inw() to a pointer.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: implement on-demand HPA unlocking
libata: use the enlarged capacity after late HPA unlock
SCSI: implement sd_unlock_native_capacity()
libata-sff: trivial corrections to Kconfig help text
sata_nv: don't diddle with nIEN on mcp55
sata_via: magic vt6421 fix for transmission problems w/ WD drives
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched, trace: Fix sched_switch() prev_state argument
sched: Fix wake_affine() vs RT tasks
sched: Make sure timers have migrated before killing the migration_thread
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, smpboot: Fix cores per node printing on boot
x86/amd-iommu: Fall back to GART if initialization fails
x86/amd-iommu: Fix crash when request_mem_region fails
x86/mm: Remove unused DBG() macro
arch/x86/kernel: Add missing spin_unlock
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/macio: Fix probing of macio devices by using the right of match table
agp/uninorth: Fix oops caused by flushing too much
powerpc/pasemi: Update MAINTAINERS file
powerpc/cell: Fix integer constant warning
powerpc/kprobes: Remove resume_execution() in kprobes
powerpc/macio: Don't dereference pointer before null check
* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: avoid allocation causing potential swap activity on the resume path
xen: ensure timer tick is resumed even on CPU driving the resume
* 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Fix crash in swevents
perf buildid-list: Fix --with-hits event processing
perf scripts python: Give field dict to unhandled callback
perf hist: fix objdump output parsing
perf-record: Check correct pid when forking
perf: Do the comm inheritance per thread in event__process_task
perf: Use event__process_task from perf sched
perf: Process comm events by tid
blktrace: Fix new kernel-doc warnings
perf_events: Fix unincremented buffer base on partial copy
perf_events: Fix event scheduling issues introduced by transactional API
perf_events, trace: Fix perf_trace_destroy(), mutex went missing
perf_events, trace: Fix probe unregister race
perf_events: Fix races in group composition
perf_events: Fix races and clean up perf_event and perf_mmap_data interaction
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio: console: Fix crash when port is unplugged and blocked for write
virtio: console: Fix crash when hot-unplugging a port and read is blocked
virtio-blk: fix minimum number of S/G elements
Frederic reported that because swevents handling doesn't disable IRQs
anymore, we can get a recursion of perf_adjust_period(), once from
overflow handling and once from the tick.
If both call ->disable, we get a double hlist_del_rcu() and trigger
a LIST_POISON2 dereference.
Since we don't actually need to stop/start a swevent to re-programm
the hardware (lack of hardware to program), simply nop out these
callbacks for the swevent pmu.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1275557609.27810.35218.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
drm/radeon/kms: make sure display hw is disabled when suspending
drm/vmwgfx: Allow userspace to change default layout. Bump minor.
drm/vmwgfx: Fix framebuffer modesetting
drm/vmwgfx: Fix vga save / restore with display topology.
vgaarb: use MIT license
vgaarb: convert pr_devel() to pr_debug()
drm: fix typos in Linux DRM Developer's Guide
drm/radeon/kms/pm: voltage fixes
drm/radeon/kms/pm: radeon_set_power_state fixes
drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
drm/radeon/kms/evergreen: add initial CS parser
drm/kms: disable/enable poll around switcheroo on/off
drm/nouveau: fixup confusion over which handle the DSM is hanging off.
drm/nouveau: attempt to get bios from ACPI v3
drm/nv50: cast IGP memory location to u64 before shifting
drm/ttm: Fix ttm_page_alloc.c
drm/ttm: Fix cached TTM page allocation.
drm/vmwgfx: Remove some leftover debug messages.
...
When a program that has a virtio port opened and blocked for a write
operation, a port hot-unplug event will later led to a crash when
SIGTERM was sent to the program. Fix that.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When removing a port we don't check if a program was blocked for read.
This leads to a crash when SIGTERM is sent to the program after
hot-unplugging the port.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We need at least one S/G element to operate properly, as does the block
layer which increments it to one anyway. We hit this due to a qemu
bug which advertises a sg_elements of 0 under some circumstances.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (tweaked logic)
I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b04d to fix the faulty drivers.
As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move strict I2C address validity check to a single function, and
document the reserved I2C addresses there.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Do basic address validity checks when a client is being registered. We
already had checks in place for devices which are being detected, but
not for devices which are simply instantiated.
This is a very basic check. We don't want to do strict checking here
because some devices are known to infringe the I2C address constraints
(e.g. IR receivers at 7-bit address 0x7a while this value is
supposedly reserved for 10-bit addresses.) So we assume the caller
knows what it is doing.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Use the same I2C device presence detection code for legacy and new
device detection functions. This is more consistent and makes the code
smaller.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Remove all trailing whitespace in Documentation/i2c.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Since the device we are resuming could be the device containing the
swap device we should ensure that the allocation cannot cause
IO.
On resume, this path is triggered when the running system tries to
continue using its devices. If it cannot then the resume will fail;
to try to avoid this we let it dip into the emergency pools.
The majority of these changes were made when linux-2.6.18-xen.hg
changeset e8b49cfbdac0 was ported upstream in
a144ff09bc but somehow this hunk was
dropped.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Stable Kernel <stable@kernel.org> # .32.x
The core suspend/resume code is run from stop_machine on CPU0 but
parts of the suspend/resume machinery (including xen_arch_resume) are
run on whichever CPU happened to schedule the xenwatch kernel thread.
As part of the non-core resume code xen_arch_resume is called in order
to restart the timer tick on non-boot processors. The boot processor
itself is taken care of by core timekeeping code.
xen_arch_resume uses smp_call_function which does not call the given
function on the current processor. This means that we can end up with
one CPU not receiving timer ticks if the xenwatch thread happened to
be scheduled on CPU > 0.
Use on_each_cpu instead of smp_call_function to ensure the timer tick
is resumed everywhere.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Stable Kernel <stable@kernel.org> # .32.x
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The host may change the layout and, since the change is
communicated to the master, the master needs a way to
communicate the change to the kernel driver.
The minor version number is bumped to advertize the
availability of this feature.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Must set SVGA_NUM_REG_GUEST_DISPLAY before setting up the display information.
Signed-off-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vga save / restore previously didn't handle the display topology case.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We want to be able to use CONFIG_DYNAMIC_DEBUG in arbiter code, switch
the few existing pr_devel() calls to pr_debug().
Also, add one more debug information regarding decoding count.
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A few typos in the DRM Developer's Guide.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Enable GPIO voltage for non pm modes as well so resetting
the default voltage works.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- wait for vbl for both profile and dynpm
- unify profile and dynpm code paths more
- call pm_misc before of after clocks to make
sure voltage is changed in the proper order.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The default power state does not always match the default clocks and voltage
for a particular card. The information in the firmware info table is correct
and should be used in preference to the info the default power state.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- This enables voltage adjustment on r6xx+ and certain
r5xx asics.
- Voltage drop support is already available for most
r1xx-r5xx asics.
V2: endian fix for voltage table.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build errors in EDAC drivers caused by the OF
device_node pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fixes build errors in drivers caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sarah Sharp