One thing became visible when writing the blamed commit, and that was
that STP and PTP frames injected by net/dsa/tag_sja1105.c using the
deferred xmit mechanism are always classified to the pvid of the CPU
port, regardless of whatever VLAN there might be in these packets.
So a decision needed to be taken regarding the mechanism through which
we should ensure that delivery of STP and PTP traffic is possible when
we are in a VLAN awareness mode that involves tag_8021q. This is because
tag_8021q is not concerned with managing the pvid of the CPU port, since
as far as tag_8021q is concerned, no traffic should be sent as untagged
from the CPU port. So we end up not actually having a pvid on the CPU
port if we only listen to tag_8021q, and unless we do something about it.
The decision taken at the time was to keep VLAN 1 in the list of
priv->dsa_8021q_vlans, and make it a pvid of the CPU port. This ensures
that STP and PTP frames can always be sent to the outside world.
However there is a problem. If we do the following while we are in
the best_effort_vlan_filtering=true mode:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1
Then untagged and pvid-tagged frames should be dropped. But we observe
that they aren't, and this is because of the precaution we took that VID
1 is always installed on all ports.
So clearly VLAN 1 is not good for this purpose. What about VLAN 0?
Well, VLAN 0 is managed by the 8021q module, and that module wants to
ensure that 802.1p tagged frames are always received by a port, and are
always transmitted as VLAN-tagged (with VLAN ID 0). Whereas we want our
STP and PTP frames to be untagged if the stack sent them as untagged -
we don't want the driver to just decide out of the blue that it adds
VID 0 to some packets.
So what to do?
Well, there is one other VLAN that is reserved, and that is 4095:
$ ip link add link swp2 name swp2.4095 type vlan id 4095
Error: 8021q: Invalid VLAN id.
$ bridge vlan add dev swp2 vid 4095
Error: bridge: Vlan id is invalid.
After we made this change, VLAN 1 is indeed forwarded and/or dropped
according to the bridge VLAN table, there are no further alterations
done by the sja1105 driver.
Fixes: ec5ae61076 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver continues probing when a port is configured for an
unsupported PHY interface type, instead it should stop.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If any of sja1105_static_config_load(), sja1105_clocking_setup() or
sja1105_devlink_setup() fails, we can't just return in the middle of
sja1105_setup() or memory will leak. Add a cleanup path.
Fixes: 0a7bdbc23d ("net: dsa: sja1105: move devlink param code to sja1105_devlink.c")
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike other drivers which pretty much end their .probe() execution with
dsa_register_switch(), the sja1105 does some extra stuff. When that
fails with -ENOMEM, the driver is quick to return that, forgetting to
call dsa_unregister_switch(). Not critical, but a bug nonetheless.
Fixes: 4d7525085a ("net: dsa: sja1105: offload the Credit-Based Shaper qdisc")
Fixes: a68578c20a ("net: dsa: Make deferred_xmit private to sja1105")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of the sja1105_dynamic_config.c file there is a diagram
of the dynamic config interface layout:
packed_buf
|
V
+-----------------------------------------+------------------+
| ENTRY BUFFER | COMMAND BUFFER |
+-----------------------------------------+------------------+
<----------------------- packed_size ------------------------>
So in order to pack/unpack the command bits into the buffer,
sja1105_vl_lookup_cmd_packing must first advance the buffer pointer by
the length of the entry. This is similar to what the other *cmd_packing
functions do.
This bug exists because the command packing function for P/Q/R/S was
copied from the E/T generation, and on E/T, the command was actually
embedded within the entry buffer itself.
Fixes: 94f94d4acf ("net: dsa: sja1105: add static tables for virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the tiocmset and rfkill requests which erroneously used
usb_rcvctrlpipe().
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify some fields of the USB descriptor to make sure the driver
could be used by the device.
Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.
BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa
Reported-by: syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com
Fixes: c2198943e3 ("r8152: search the configuration of vendor mode")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/nfc/nfcmrvl follows this syntax, but the content
inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warnings from kernel-doc.
For e.g., running scripts/kernel-doc -none on drivers/nfc/nfcmrvl/spi.c
causes warning:
warning: expecting prototype for Marvell NFC(). Prototype was for SPI_WAIT_HANDSHAKE() instead
Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCR_MATRIX field was set to all 1's when VLAN filtering is enabled, but
was not reset when it is disabled, which may cause traffic leaks:
ip link add br0 type bridge vlan_filtering 1
ip link add br1 type bridge vlan_filtering 1
ip link set swp0 master br0
ip link set swp1 master br1
ip link set br0 type bridge vlan_filtering 0
ip link set br1 type bridge vlan_filtering 0
# traffic in br0 and br1 will start leaking to each other
As port_bridge_{add,del} have set up PCR_MATRIX properly, remove the
PCR_MATRIX write from mt7530_port_set_vlan_aware.
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
two fixes for the fq_pie scheduler
- patch 1/2 restores the possibility to use 65536 flows with fq_pie,
preserving the fix for an endless loop in the control plane
- patch 2/2 fixes an OOB access that can be observed in the traffic
path of fq_pie scheduler, when the classification selects a flow
beyond the allocated space.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the following script:
# tc qdisc add dev eth0 handle 0x1 root fq_pie flows 2
# tc qdisc add dev eth0 clsact
# tc filter add dev eth0 egress matchall action skbedit priority 0x10002
# ping 192.0.2.2 -I eth0 -c2 -w1 -q
produces the following splat:
BUG: KASAN: slab-out-of-bounds in fq_pie_qdisc_enqueue+0x1314/0x19d0 [sch_fq_pie]
Read of size 4 at addr ffff888171306924 by task ping/942
CPU: 3 PID: 942 Comm: ping Not tainted 5.12.0+ #441
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014
Call Trace:
dump_stack+0x92/0xc1
print_address_description.constprop.7+0x1a/0x150
kasan_report.cold.13+0x7f/0x111
fq_pie_qdisc_enqueue+0x1314/0x19d0 [sch_fq_pie]
__dev_queue_xmit+0x1034/0x2b10
ip_finish_output2+0xc62/0x2120
__ip_finish_output+0x553/0xea0
ip_output+0x1ca/0x4d0
ip_send_skb+0x37/0xa0
raw_sendmsg+0x1c4b/0x2d00
sock_sendmsg+0xdb/0x110
__sys_sendto+0x1d7/0x2b0
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fe69735c3eb
Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 f3 0f 1e fa 48 8d 05 75 42 2c 00 41 89 ca 8b 00 85 c0 75 14 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 75 c3 0f 1f 40 00 41 57 4d 89 c7 41 56 41 89
RSP: 002b:00007fff06d7fb38 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 000055e961413700 RCX: 00007fe69735c3eb
RDX: 0000000000000040 RSI: 000055e961413700 RDI: 0000000000000003
RBP: 0000000000000040 R08: 000055e961410500 R09: 0000000000000010
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fff06d81260
R13: 00007fff06d7fb40 R14: 00007fff06d7fc30 R15: 000055e96140f0a0
Allocated by task 917:
kasan_save_stack+0x19/0x40
__kasan_kmalloc+0x7f/0xa0
__kmalloc_node+0x139/0x280
fq_pie_init+0x555/0x8e8 [sch_fq_pie]
qdisc_create+0x407/0x11b0
tc_modify_qdisc+0x3c2/0x17e0
rtnetlink_rcv_msg+0x346/0x8e0
netlink_rcv_skb+0x120/0x380
netlink_unicast+0x439/0x630
netlink_sendmsg+0x719/0xbf0
sock_sendmsg+0xe2/0x110
____sys_sendmsg+0x5ba/0x890
___sys_sendmsg+0xe9/0x160
__sys_sendmsg+0xd3/0x170
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff888171306800
which belongs to the cache kmalloc-256 of size 256
The buggy address is located 36 bytes to the right of
256-byte region [ffff888171306800, ffff888171306900)
The buggy address belongs to the page:
page:00000000bcfb624e refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x171306
head:00000000bcfb624e order:1 compound_mapcount:0
flags: 0x17ffffc0010200(slab|head|node=0|zone=2|lastcpupid=0x1fffff)
raw: 0017ffffc0010200 dead000000000100 dead000000000122 ffff888100042b40
raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888171306800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888171306880: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
>ffff888171306900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888171306980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888171306a00: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
fix fq_pie traffic path to avoid selecting 'q->flows + q->flows_cnt' as a
valid flow: it's an address beyond the allocated memory.
Fixes: ec97ecf1eb ("net: sched: add Flow Queue PIE packet scheduler")
CC: stable@vger.kernel.org
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the patch that fixed an endless loop in_fq_pie_init() was not considering
that 65535 is a valid class id. The correct bugfix for this infinite loop
is to change 'idx' to become an u32, like Colin proposed in the past [1].
Fix this as follows:
- restore 65536 as maximum possible values of 'flows_cnt'
- use u32 'idx' when iterating on 'q->flows'
- fix the TDC selftest
This reverts commit bb2f930d6d.
[1] https://lore.kernel.org/netdev/20210407163808.499027-1-colin.king@canonical.com/
CC: Colin Ian King <colin.king@canonical.com>
CC: stable@vger.kernel.org
Fixes: bb2f930d6d ("net/sched: fix infinite loop in sch_fq_pie")
Fixes: ec97ecf1eb ("net: sched: add Flow Queue PIE packet scheduler")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If runtime power menagement is enabled, the gigabit ethernet PLL would
be disabled after macb_probe(). During this period of time, the system
would hang up if we try to access GEMGXL control registers.
We can't put runtime_pm_get/runtime_pm_put/ there due to the issue of
sleep inside atomic section (7fa2955ff7 ("sh_eth: Fix sleeping
function called from invalid context"). Add netif_running checking to
ensure the device is available before accessing GEMGXL device.
Changed in v2:
- Use netif_running instead of its own flag
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7628/88 SoC(s) have other (limited) packet counter registers than
currently supported in the mtk_eth_soc driver. This patch adds support
for reading these registers, so that the packet statistics are correctly
updated.
Additionally the defines for the non-MT7628 variant packet counter
registers are added and used in this patch instead of using hard coded
values.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Reto Schneider <code@reto-schneider.ch>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Vinicius Costa Gomes as maintainer for these qdiscs.
These qdiscs are all TSN (Time Sensitive Networking) related.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dbd1759e6a ("ipv6: on reassembly, record frag_max_size")
filled the frag_max_size field in IP6CB in the input path.
The field should also be filled in case of atomic fragments.
Fixes: dbd1759e6a ('ipv6: on reassembly, record frag_max_size')
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFC driver can be configured via modparam to work using MSI-X, MSI or
legacy IRQ interrupts. In the last one, the interrupt was not properly
released on module remove.
It was not freed because the flag irqs_hooked was not set during
initialization in the case of using legacy IRQ.
Example of (trimmed) trace during module remove without this fix:
remove_proc_entry: removing non-empty directory 'irq/125', leaking at least '0000:3b:00.1'
WARNING: CPU: 39 PID: 3658 at fs/proc/generic.c:715 remove_proc_entry+0x15c/0x170
...trimmed...
Call Trace:
unregister_irq_proc+0xe3/0x100
free_desc+0x29/0x70
irq_free_descs+0x47/0x70
mp_unmap_irq+0x58/0x60
acpi_unregister_gsi_ioapic+0x2a/0x40
acpi_pci_irq_disable+0x78/0xb0
pci_disable_device+0xd1/0x100
efx_pci_remove+0xa1/0x1e0 [sfc]
pci_device_remove+0x38/0xa0
__device_release_driver+0x177/0x230
driver_detach+0xcb/0x110
bus_remove_driver+0x58/0xd0
pci_unregister_driver+0x2a/0xb0
efx_exit_module+0x24/0xf40 [sfc]
__do_sys_delete_module.constprop.0+0x171/0x280
? exit_to_user_mode_prepare+0x83/0x1d0
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f9f9385800b
...trimmed...
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP is used as transport and a program on the
system connects to RDS port 16385, connection is
accepted but denied per the rules of RDS. However,
RDS connections object is left in the list. Next
loopback connection will select that connection
object as it is at the head of list. The connection
attempt will hang as the connection object is set
to connect over TCP which is not allowed
The issue can be reproduced easily, use rds-ping
to ping a local IP address. After that use any
program like ncat to connect to the same IP
address and port 16385. This will hang so ctrl-c out.
Now try rds-ping, it will hang.
To fix the issue this patch adds checks to disallow
the connection object creation and destroys the
connection object.
Signed-off-by: Rao Shoaib <rao.shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove Ioana Radulescu from dpaa2-eth since she is no longer working on
the DPAA2 set of drivers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a situation where memory allocation or dma mapping fails, an
invalid address is programmed into the descriptor. This can lead
to memory corruption. If the memory allocation fails, DMA should
reuse the previous skb and mapping and drop the packet. This patch
also increments rx drop counter.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver ")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot call bcm_sf2_reg_rgmii_cntrl() for a port that is not RGMII,
yet we do that in bcm_sf2_sw_mac_link_up() irrespective of the port's
interface. Move that read until we have properly qualified the PHY
interface mode. This avoids triggering a warning on 7278 platforms that
have GMII ports.
Fixes: 55cfeb3969 ("net: dsa: bcm_sf2: add function finding RGMII register")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discussions for network-related code should include the netdev list.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating to latest mainline for some testing on the GARDENA smart
gateway based on the MT7628, I noticed that ethernet does not work any
more. Commit e9229ffd55 ("net: ethernet: mtk_eth_soc: implement
dynamic interrupt moderation") introduced this problem, as it missed the
RX_DIM & TX_DIM configuration for this SoC variant. This patch fixes
this by calling mtk_dim_rx() & mtk_dim_tx() in this case as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: e9229ffd55 ("net: ethernet: mtk_eth_soc: implement dynamic interrupt moderation")
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Reto Schneider <code@reto-schneider.ch>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang says:
====================
net: fixes for stmmac
Two clock fixes for stmmac driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be a mistake to fix conflicts when removing RFC tag to
repost the patch.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/net/ethernet/microchip/encx24j600 files follows
this syntax, but the content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc.
For e.g., running scripts/kernel-doc -none
drivers/net/ethernet/microchip/encx24j600_hw.h emits:
warning: expecting prototype for h(). Prototype was for _ENCX24J600_HW_H() instead
Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9 ("ixgbe: Enable jumbo frames support w/ SR-IOV")
Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the nci test suite produces a binary, nci_dev, that git then
tries to track. Add a .gitignore file to tell git to ignore this binary.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 31db0dbd72 ("net: hso: check for allocation failure in
hso_create_bulk_serial_device()") recently started returning an error
when the driver fails to allocate resources for the interrupt endpoint
and tiocmget functionality.
For consistency let's bail out from probe also if the URB allocation
fails.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update Sergei's email address, as per commit 534a8bf0cc
("MAINTAINERS: switch to my private email for Renesas Ethernet
drivers").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware register having the server TID base can contain
invalid values when adapter is in bad state (for example,
due to AER fatal error). Reading these invalid values in the
register can lead to out-of-bound memory access. So, fix
by using the saved server TID base when clearing filters.
Fixes: b1a79360ee ("cxgb4: Delete all hash and TCAM filters before resource cleanup")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmCkqdYACgkQSD+KveBX
+j7Otwf/YXMyRa87Tw91e01Rcc5v+2TYd2rsqAwI0WsX58PnxaMZ//pxs7ki0si2
m9Q0sFLW8xhn58fUyKKzhddpG+w2UamRLGn7pht0iO3sq11ccFV10YfuuyS4uEGk
G6w4FXVKvubM7j8DMYfLtBocsUidIxfWc5VqsAJdY3IpWeIsFPqv8N/q3KkgYZuD
1kJpg9pnxWgO4+8eLWoWWTKw6w2+yjVhcahrJ4ZRf0p1IVAhN07exwdpcMk1dDoi
xmEt+7027PjTKEP9oRB22235sIu+ryqLY3IFTnq2WsthHu1nfxFUzspECLMB6aEY
Ujv8TxwY/H1/ElaVIyKnYa0dUJWB0g==
=Ehdm
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2021-05-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2021-05-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
data->ctrl_stats should be memset with correct size.
Fixes: bfad2b979d ("ethtool: add interface to read standard MAC Ctrl stats")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not correct to call napi_schedule() in pure process
context. Because we use __raise_softirq_irqoff() we require
callers to be in a context which will eventually lead to
softirq handling (hardirq, bh disabled, etc.).
With code as is users will see:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Fixes: a8dd7ac12f ("net/mlx5e: Generalize RQ activation")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Termination tables are restricted to have the default miss action and
cannot be set to forward to another table in case of a miss.
If the fs prio of the termination table is not the last one in the
list, fs_core will attempt to attach it to another table.
Set the unmanaged ft flag when creating the termination table ft
and select the tc offload prio for it to prevent fs_core from selecting
the forwarding to next ft miss action and use the default one.
In addition, set the flow that forwards to the termination table to
ignore ft level restrictions since the ft level is not set by fs_core
for unamanged fts.
Fixes: 249ccc3c95 ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
During driver probe of device that has dynamic MSI-X feature enabled,
the following error is printed in some FW flavour (not released yet).
mlx5_core 0000:06:00.0: firmware version: 4.7.4387
mlx5_core 0000:06:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link)
mlx5_core 0000:06:00.0: mlx5_cmd_check:777:(pid 70599): SET_HCA_CAP(0x109) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x0)
mlx5_core 0000:06:00.0: set_hca_cap:622:(pid 70599): handle_hca_cap failed
mlx5_core 0000:06:00.0: mlx5_function_setup:1045:(pid 70599): set_hca_cap failed
mlx5_core 0000:06:00.0: probe_one:1465:(pid 70599): mlx5_init_one failed with error code -22
mlx5_core: probe of 0000:06:00.0 failed with error -22
In order to make the setting capability of MSI-X future proof, let's
query the current capabilities first.
Fixes: 604774add5 ("net/mlx5: Dynamically assign MSI-X vectors count")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
net/mlx5: Expose MPFS configuration API
MPFS is the multi physical function switch that bridges traffic between
the physical port and any physical functions associated with it. The
driver is required to add or remove MAC entries to properly forward
incoming traffic to the correct physical function.
We export the API to control MPFS so that other drivers, such as
mlx5_vdpa are able to add MAC addresses of their network interfaces.
The MAC address of the vdpa interface must be configured into the MPFS L2
address. Failing to do so could cause, in some NIC configurations, failure
to forward packets to the vdpa network device instance.
Fix this by adding calls to update the MPFS table.
CC: <mst@redhat.com>
CC: <jasowang@redhat.com>
CC: <virtualization@lists.linux-foundation.org>
Fixes: 1a86b377aa ("vdpa/mlx5: Add VDPA driver for supported mlx5 devices")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Avoid division by zero in the error flow. In the driver TC number can be
either 1 or 8. When TC count is set to 1, driver zero netdev->num_tc.
Hence, need to convert it back from 0 to 1 in the error flow.
Fixes: fa3748775b ("net/mlx5e: Handle errors from netif_set_real_num_{tx,rx}_queues")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Rules with MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE dest flag are
translated to destination FT in eswitch. Currently it is not possible to
mirror such rules because firmware doesn't support mixing FT and Vport
destinations in single rule when one of them adds encapsulation. Since the
only use case for MLX5_ESW_DEST_CHAIN_WITH_SRC_PORT_CHANGE destination is
support for tunnel endpoints on VF and trying to offload such rule with
mirror action causes either crash in fs_core or firmware error with
syndrome 0xff6a1d, reject all such rules in mlx5 TC layer.
Fixes: 10742efc20 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When handling FIB_EVENT_ENTRY_REPLACE event for a new multipath route,
lag activation can be missed if a stale (struct lag_mp)->mfi pointer
exists, which was associated with an older multipath route that had been
removed.
Normally, when a route is removed, it triggers mlx5_lag_fib_event(),
which handles FIB_EVENT_ENTRY_DEL and clears mfi pointer. But, if
mlx5_lag_check_prereq() condition isn't met, for example when eswitch is
in legacy mode, the fib event is skipped and mfi pointer becomes stale.
Fix by resetting mfi pointer to NULL every time mlx5_lag_mp_init() is
called.
Fixes: 544fe7c2e6 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5e_attach_netdev can be called prior to registering the netdevice:
Example stack:
ipoib_new_child_link ->
ipoib_intf_init->
rdma_init_netdev->
mlx5_rdma_setup_rn->
mlx5e_attach_netdev->
mlx5e_num_channels_changed ->
mlx5e_set_default_xps_cpumasks ->
netif_set_xps_queue ->
__netif_set_xps_queue -> kmalloc
If any later stage fails at any point after mlx5e_num_channels_changed()
returns, XPS allocated maps will never be freed as they
are only freed during netdev unregistration, which will never happen for
yet to be registered netdevs.
Fixes: 3909a12e79 ("net/mlx5e: Fix configuration of XPS cpumasks and netdev queues in corner cases")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
It could be the lag dev is null so stop processing the event.
In bond_enslave() the active/backup slave being set before setting the
upper dev so first event is without an upper dev.
After setting the upper dev with bond_master_upper_dev_link() there is
a second event and in that event we have an upper dev.
Fixes: 7e51891a23 ("net/mlx5e: Use netdev events to set/del egress acl forward-to-vport rule")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The result of __dev_get_by_index() is not checked for NULL, which then
passed to mlx5e_attach_encap() and gets dereferenced.
Also, in case of a successful lookup, the net_device reference count is
not incremented, which may result in net_device pointer becoming invalid
at any time during mlx5e_attach_encap() execution.
Fix by using dev_get_by_index(), which does proper reference counting on
the net_device pointer. Also, handle nullptr return value when mirred
device is not found.
It's safe to call dev_put() on the mirred net_device pointer, right
after mlx5e_attach_encap() call, because it's not being saved/copied
down the call chain.
Fixes: 3c37745ec6 ("net/mlx5e: Properly deal with encap flows add/del under neigh update")
Addresses-Coverity: ("Dereference null return value")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When a SF is inactivated and when it is in a TEARDOWN_REQUEST
state, driver still returns its state as active. This is incorrect.
Fix it by treating TEARDOWN_REQEUST as inactive state. When a SF
is still attached to the driver, on user request to reactivate EINVAL
error is returned. Inform user about it with better code EBUSY and
informative error message.
Fixes: 6a32732174 ("net/mlx5: SF, Port function state change support")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Fix print to print correct error code and not using IS_ERR() which
will just result in always printing 1.
Also return real err instead of always -EOPNOTSUPP.
Fixes: 10caabdaad ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
For remote mirroring, after the tunnel packets are received, they are
decapsulated and sent to representor, then re-encapsulated and sent
out over another tunnel. So reformat action is set only when the
destination is required to do encapsulation.
Fixes: 249ccc3c95 ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Vladimir Oltean